Aluminum electrolytic capacitors Single-ended capacitors Series/Type: B41896 Date: December 2006 EPCOS AG 2007. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Single-ended capacitors B41896 Extra long useful life 125 °C Long-life grade capacitors Applications Automotive applications Power supplies Features Wide temperature range up to 125 °C Extra long useful life High ripple current capability Compact design Low ESR Construction Radial leads Charge-discharge proof, polar Aluminum case with insulating sleeve Minus pole marking on the insulating sleeve Case with safety vent Delivery mode Terminal configurations and packing: Bulk Taped, Ammo pack Cut Kinked PAPR (protection against polarity reversal): crimped leads, J leads, bent leads Refer to chapter "Single-ended capacitors - Taping, packing and lead configurations" for further details and ordering example. Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 32 B41896 Extra long useful life 125 °C Specifications and characteristics in brief Rated voltage VR Surge voltage VS Rated capacitance CR Capacitance tolerance 10 ... 63 V DC 1.15 VR 1 ... 10000 µF ±20% M Dissipation factor tan δ (20 °C, 120 Hz) For capacitance higher than 1000 µF add 0.02 for every increase of 1000 µF. VR (V DC) tan δ (max.) Leakage current Ileak (20 °C, 5 min) Self-inductance ESL Useful life 125 °C, VR, IAC,R 10 0.20 16 ... 25 0.17 50 0.10 63 0.15 or 3 µA, whichever is greater Diameter (mm) ≤ 12.5 16 18 ESL (nH) 20 26 34 > 2500 h for d = 8 mm up to 50 V > 2000 h for d = 8 mm for 63 V > 3500 h for d = 10 mm up to 50 V > 3000 h for d = 10 mm for 63 V > 7000 h for d ≥ 12.5 mm up to 50 V > 5000 h for d ≥ 12.5 mm for 63 V 135 °C, VR, 0.75 IAC,R > 3000 h for d ≥ 12.5 mm up to 50 V Requirements ∆C/C tan δ Ileak ≤ ±35% of initial value ≤ 3 times initial specified limit ≤ initial specified limit Voltage endurance test 125 °C, VR 2500 h for d = 8 mm up to 50 V 3500 h for d = 10 mm up to 50 V 7000 h for d ≥ 12.5 mm up to 50 V Post test requirements 35 0.12 ∆C/C tan δ Ileak 2000 h for d = 8 mm for 63 V 3000 h for d = 10 mm for 63 V 5000 h for d ≥ 12.5 mm for 63 V ≤ ±30% of initial value ≤ 2 times initial specified limit ≤ initial specified limit Vibration resistance test To IEC 60068-2-6, test Fc: Displacement amplitude 0.75 mm, frequency range 10 … 2000 Hz, acceleration max. 20 g, duration 3 × 2 h. Capacitor rigidly clamped by the aluminum case. IEC climatic category To IEC 60068-1: 55/125/56 (55 °C/+125 °C/56 days damp heat test) Sectional specification AEC-Q200, IEC 60384-4 Please read Cautions and warnings and Important notes at the end of this document. Page 3 of 32 B41896 Extra long useful life 125 °C Dimensional drawings With stand-off rubber seal Diameters (mm): 8, 10, 12.5, 16, 18 With flat rubber seal Diameter (mm): 8 Dimensions and weights Dimensions (mm) d +0.5 8 10 10 10 12.5 12.5 12.5 16 16 16 18 18 18 18 18 l 11.5 +1.5 12.5 +1.0 16 +1.0 20 +2.0 20 +2.0 25 +2.0 30 +2.0 20 +2.0 25 +2.0 31.5 +2.0 20 +2.0 25 +2.0 31.5 +2.0 35 +2.0 40 +2.0 Please read Cautions and warnings and Important notes at the end of this document. a ±0.5 3.5 5.0 5.0 5.0 5.0 5.0 5.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 Page 4 of 32 b 0.60 ±0.05 0.60 ±0.05 0.60 ±0.05 0.60 ±0.05 0.60 ±0.05 0.60 ±0.05 0.80 ±0.05 0.80 ±0.05 0.80 ±0.05 0.80 ±0.05 0.80 ±0.1 0.80 ±0.1 0.80 ±0.1 0.80 ±0.1 0.80 ±0.1 Approx. weight g 1.0 1.6 1.9 2.6 3.6 4.5 5.3 5.5 7.5 7.8 8.0 9.0 11.0 13.0 16.0 B41896 Extra long useful life 125 °C Overview of available types VR (V DC) 10 16 25 35 50 63 Case dimensions d × l (mm) CR (µF) 1.0 8 × 11.5 2.2 8 × 11.5 3.3 8 × 11.5 4.7 8 × 11.5 10 8 × 11.5 12 8 × 11.5 15 8 × 11.5 18 8 × 11.5 22 8 × 11.5 27 8 × 11.5 33 8 × 11.5 39 8 × 11.5 47 8 × 11.5 56 8 × 11.5 68 8 × 11.5 82 8 × 11.5 8 × 11.5 8 × 11.5 10 × 12.5 10 × 16 10 × 20 100 8 × 11.5 8 × 11.5 8 10 × 11.5 × 12.5 10 × 12.5 120 8 × 11.5 8 × 11.5 10 × 12.5 10 × 16 150 8 × 11.5 8 × 11.5 10 × 16 10 × 16 12.5 × 20 180 8 × 11.5 8 × 11.5 10 × 16 10 × 20 12.5 × 20 220 8 × 11.5 8 × 11.5 10 × 12.5 10 × 16 10 × 20 12.5 × 25 270 8 × 11.5 10 × 12.5 10 × 12.5 10 × 20 12.5 × 20 12.5 × 25 330 8 × 11.5 10 × 12.5 10 × 16 10 × 20 12.5 × 20 12.5 × 25 390 10 × 12.5 10 × 12.5 10 × 16 12.5 × 20 12.5 × 25 12.5 × 30 470 10 × 12.5 10 × 16 10 × 20 12.5 × 20 12.5 × 25 16 × 20 16 × 25 560 10 × 16 10 × 16 10 × 20 12.5 × 25 16 × 20 16 × 31.5 680 10 × 16 10 × 16 10 × 20 12.5 × 25 16 18 × 25 × 20 16 × 31.5 820 10 × 20 10 × 20 12.5 × 20 16 × 20 16 × 31.5 18 × 31.5 1000 10 × 20 12.5 × 20 12.5 × 25 16 × 20 12.5 × 40 16 × 25 18 × 20 16 × 31.5 18 × 35 Please read Cautions and warnings and Important notes at the end of this document. Page 5 of 32 B41896 Extra long useful life 125 °C VR (V DC) 10 16 25 35 50 63 16 × 25 18 × 20 18 × 31.5 18 × 40 Case dimensions d × l (mm) CR (µF) 1200 12.5 × 20 12.5 × 20 12.5 × 25 1500 12.5 × 20 12.5 × 25 16 × 20 16 × 31.5 18 × 35 1800 12.5 × 20 12.5 × 25 12.5 × 40 16 × 25 18 × 20 16 × 31.5 18 × 40 2200 12.5 × 25 12.5 × 30 16 × 20 16 18 × 31.5 × 25 18 × 35 2700 16 × 20 16 18 × 25 × 20 16 × 31.5 18 × 40 3300 16 × 25 16 × 31.5 18 × 31.5 3900 16 18 × 25 × 20 16 × 31.5 18 × 35 4700 16 × 31.5 18 × 31.5 18 × 40 5600 16 × 31.5 18 × 35 6800 18 × 31.5 18 × 40 8200 18 × 35 10000 18 × 40 Other voltage and capacitance ratings are available upon request. Please read Cautions and warnings and Important notes at the end of this document. Page 6 of 32 B41896 Extra long useful life 125 °C Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm ESRmax 10 kHz 40 °C Ω VR = 10 V DC 220 8 × 11.5 270 8 × 11.5 330 8 × 11.5 390 10 × 12.5 470 10 × 12.5 560 10 × 16 680 10 × 16 820 10 × 20 1000 10 × 20 1200 12.5 × 20 1500 12.5 × 20 1800 12.5 × 20 2200 12.5 × 25 2700 16 × 20 3300 16 × 25 3900 16 × 25 3900 18 × 20 4700 16 × 31.5 5600 16 × 31.5 6800 18 × 31.5 8200 18 × 35 10000 18 × 40 5.170 5.170 5.170 2.116 2.116 1.104 1.104 0.592 0.592 0.484 0.484 0.484 0.285 0.299 0.238 0.238 0.273 0.185 0.185 0.178 0.178 0.150 ESRmax 120 Hz 20 °C Ω 1.148 0.936 0.766 0.648 0.538 0.451 0.372 0.308 0.253 0.211 0.168 0.140 0.126 0.103 0.090 0.078 0.078 0.070 0.063 0.056 0.052 0.048 ESRmax 10 kHz 20 °C Ω Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 125 °C mA IAC,max Ordering code 100 kHz (composition see 105 °C below) mA 0.646 0.646 0.646 0.265 0.265 0.138 0.138 0.074 0.074 0.061 0.061 0.061 0.036 0.037 0.030 0.030 0.034 0.023 0.023 0.022 0.022 0.019 0.573 0.573 0.573 0.230 0.230 0.115 0.115 0.062 0.062 0.055 0.055 0.055 0.033 0.034 0.026 0.026 0.031 0.022 0.022 0.021 0.019 0.016 340 340 340 680 680 965 965 1205 1205 1820 1820 1820 2280 2280 2860 2860 2490 3160 3160 3500 3840 4230 442 442 442 884 884 1255 1255 1566 1566 2366 2366 2366 2964 2964 3718 3718 3237 4108 4108 4550 4992 5499 B41896C3227M*** B41896C3277M*** B41896C3337M*** B41896C3397M*** B41896C3477M*** B41896C3567M*** B41896C3687M*** B41896C3827M*** B41896C3108M*** B41896C3128M*** B41896C3158M*** B41896C3188M*** B41896C3228M*** B41896C3278M*** B41896C3338M*** B41896C3398M*** B41896D3398M*** B41896C3478M*** B41896C3568M*** B41896C3688M*** B41896C3828M*** B41896C3109M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 32 B41896 Extra long useful life 125 °C Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm ESRmax 10 kHz 40 °C Ω VR = 16 V DC 100 8 × 11.5 120 8 × 11.5 150 8 × 11.5 180 8 × 11.5 220 8 × 11.5 270 10 × 12.5 330 10 × 12.5 390 10 × 12.5 470 10 × 16 560 10 × 16 680 10 × 16 820 10 × 20 1000 12.5 × 20 1200 12.5 × 20 1500 12.5 × 25 1800 12.5 × 25 2200 12.5 × 30 2200 16 × 20 2700 16 × 25 2700 18 × 20 3300 16 × 31.5 3900 16 × 31.5 4700 18 × 31.5 5600 18 × 35 6800 18 × 40 5.170 5.170 5.170 5.170 5.170 2.116 2.116 2.116 1.104 1.104 1.104 0.592 0.484 0.484 0.285 0.285 0.238 0.299 0.238 0.273 0.185 0.185 0.178 0.178 0.150 ESRmax 120 Hz 20 °C Ω 2.147 1.789 1.432 1.193 0.976 0.795 0.651 0.551 0.457 0.383 0.316 0.262 0.215 0.179 0.143 0.119 0.109 0.109 0.089 0.089 0.080 0.068 0.060 0.056 0.050 ESRmax 10 kHz 20 °C Ω Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 125 °C mA IAC,max Ordering code 100 kHz (composition see 105 °C below) mA 0.646 0.646 0.646 0.646 0.646 0.265 0.265 0.265 0.138 0.138 0.138 0.074 0.061 0.061 0.036 0.036 0.030 0.037 0.030 0.034 0.023 0.023 0.022 0.022 0.019 0.573 0.573 0.573 0.573 0.573 0.230 0.230 0.230 0.115 0.115 0.115 0.062 0.055 0.055 0.033 0.033 0.026 0.034 0.026 0.031 0.022 0.022 0.021 0.019 0.016 340 340 340 340 340 680 680 680 965 965 965 1205 1820 1820 2280 2280 2860 2280 2860 2490 3160 3160 3500 3840 4230 442 442 442 442 442 884 884 884 1255 1255 1255 1566 2366 2366 2964 2964 3718 2964 3718 3237 4108 4108 4550 4992 5499 B41896C4107M*** B41896C4127M*** B41896C4157M*** B41896C4187M*** B41896C4227M*** B41896C4277M*** B41896C4337M*** B41896C4397M*** B41896C4477M*** B41896C4567M*** B41896C4687M*** B41896C4827M*** B41896C4108M*** B41896C4128M*** B41896C4158M*** B41896C4188M*** B41896C4228M*** B41896D4228M*** B41896C4278M*** B41896D4278M*** B41896C4338M*** B41896C4398M*** B41896C4478M*** B41896C4568M*** B41896C4688M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 32 B41896 Extra long useful life 125 °C Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm ESRmax 10 kHz 40 °C Ω VR = 25 V DC 100 8 × 11.5 120 8 × 11.5 150 8 × 11.5 180 8 × 11.5 220 10 × 12.5 270 10 × 12.5 330 10 × 16 390 10 × 16 470 10 × 20 560 10 × 20 680 10 × 20 820 12.5 × 20 1000 12.5 × 25 1000 16 × 20 1200 12.5 × 25 1500 16 × 20 1800 12.5 × 40 1800 16 × 25 1800 18 × 20 2200 16 × 31.5 2200 18 × 25 2700 16 × 31.5 3300 18 × 31.5 3900 18 × 35 4700 18 × 40 5.170 5.170 5.170 5.170 2.116 2.116 1.104 1.104 0.592 0.592 0.592 0.484 0.285 0.299 0.285 0.299 0.181 0.238 0.273 0.185 0.229 0.185 0.178 0.178 0.150 ESRmax 120 Hz 20 °C Ω 2.147 1.789 1.432 1.193 0.976 0.795 0.651 0.551 0.457 0.383 0.316 0.262 0.215 0.215 0.179 0.143 0.119 0.119 0.119 0.109 0.109 0.089 0.080 0.068 0.060 ESRmax 10 kHz 20 °C Ω Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 125 °C mA IAC,max Ordering code 100 kHz (composition see 105 °C below) mA 0.646 0.646 0.646 0.646 0.265 0.265 0.138 0.138 0.074 0.074 0.074 0.061 0.036 0.037 0.036 0.037 0.023 0.030 0.034 0.023 0.029 0.023 0.022 0.022 0.019 0.573 0.573 0.573 0.573 0.230 0.230 0.115 0.115 0.062 0.062 0.062 0.055 0.033 0.034 0.033 0.034 0.021 0.026 0.031 0.022 0.025 0.022 0.021 0.019 0.016 340 340 340 340 680 680 965 965 1205 1205 1205 1820 2280 2280 2280 2280 3340 2860 2490 3160 3010 3160 3500 3840 4230 442 442 442 442 884 884 1255 1255 1566 1566 1566 2366 2964 2964 2964 2964 4342 3718 3237 4108 3913 4108 4550 4992 5499 B41896C5107M*** B41896C5127M*** B41896C5157M*** B41896C5187M*** B41896C5227M*** B41896C5277M*** B41896C5337M*** B41896C5397M*** B41896C5477M*** B41896C5567M*** B41896C5687M*** B41896C5827M*** B41896C5108M*** B41896D5108M*** B41896C5128M*** B41896D5158M*** B41896C5188M*** B41896D5188M*** B41896E5188M*** B41896C5228M*** B41896D5228M*** B41896C5278M*** B41896C5338M*** B41896C5398M*** B41896C5478M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 9 of 32 B41896 Extra long useful life 125 °C Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm ESRmax 10 kHz 40 °C Ω VR = 35 V DC 100 8 × 11.5 100 10 × 12.5 120 10 × 12.5 150 10 × 16 180 10 × 16 220 10 × 16 270 10 × 20 330 10 × 20 390 12.5 × 20 470 12.5 × 20 560 12.5 × 25 680 12.5 × 25 820 16 × 20 1000 12.5 × 40 1000 16 × 25 1000 18 × 20 1200 16 × 25 1200 18 × 20 1500 16 × 31.5 1800 16 × 31.5 2200 18 × 35 2700 18 × 40 5.170 2.116 2.116 1.104 1.104 1.104 0.592 0.592 0.484 0.484 0.285 0.285 0.299 0.181 0.238 0.273 0.238 0.273 0.185 0.185 0.178 0.150 ESRmax 120 Hz 20 °C Ω 1.516 1.516 1.263 1.011 0.842 0.689 0.561 0.459 0.389 0.323 0.271 0.223 0.185 0.152 0.152 0.152 0.126 0.126 0.101 0.084 0.080 0.065 ESRmax 10 kHz 20 °C Ω Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 125 °C mA IAC,max Ordering code 100 kHz (composition see 105 °C below) mA 0.646 0.265 0.265 0.138 0.138 0.138 0.074 0.074 0.061 0.061 0.036 0.036 0.037 0.023 0.030 0.034 0.030 0.034 0.023 0.023 0.022 0.019 0.573 0.230 0.230 0.115 0.115 0.115 0.062 0.062 0.055 0.055 0.033 0.033 0.034 0.021 0.026 0.031 0.026 0.031 0.022 0.022 0.019 0.016 340 680 680 965 965 965 1205 1205 1820 1820 2280 2280 2280 3340 2860 2490 2860 2490 3160 3160 3840 4230 442 884 884 1255 1255 1255 1566 1566 2366 2366 2964 2964 2964 4342 3718 3237 3718 3237 4108 4108 4992 5499 B41896C7107M*** B41896D7107M*** B41896C7127M*** B41896C7157M*** B41896C7187M*** B41896C7227M*** B41896C7277M*** B41896C7337M*** B41896C7397M*** B41896C7477M*** B41896C7567M*** B41896C7687M*** B41896C7827M*** B41896C7108M*** B41896D7108M*** B41896E7108M*** B41896C7128M*** B41896D7128M*** B41896C7158M*** B41896C7188M*** B41896C7228M*** B41896C7278M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 10 of 32 B41896 Extra long useful life 125 °C Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm VR = 50 V DC 1 8 × 11.5 2.2 8 × 11.5 3.3 8 × 11.5 4.7 8 × 11.5 10 8 × 11.5 12 8 × 11.5 15 8 × 11.5 18 8 × 11.5 22 8 × 11.5 27 8 × 11.5 33 8 × 11.5 39 8 × 11.5 47 8 × 11.5 56 8 × 11.5 68 8 × 11.5 82 8 × 11.5 100 10 × 12.5 120 10 × 16 150 10 × 16 180 10 × 20 220 10 × 20 270 12.5 × 20 330 12.5 × 20 390 12.5 × 25 470 12.5 × 25 470 16 × 20 ESRmax 10 kHz 40 °C Ω ESRmax 120 Hz 20 °C Ω ESRmax 10 kHz 20 °C Ω 6.396 126.313 0.800 6.396 57.415 0.800 6.396 38.277 0.800 6.396 26.875 0.800 6.396 12.631 0.800 6.396 10.526 0.800 6.396 8.421 0.800 6.396 7.017 0.800 6.396 5.742 0.800 6.396 4.678 0.800 4.920 3.828 0.615 4.129 3.239 0.516 3.466 2.688 0.433 2.909 2.256 0.364 2.441 1.858 0.305 2.049 1.540 0.256 1.820 1.263 0.228 1.104 1.053 0.138 1.104 0.842 0.138 0.592 0.702 0.074 0.592 0.574 0.074 0.484 0.468 0.061 0.484 0.383 0.061 0.285 0.324 0.036 0.269 0.069 0.036 0.299 0.269 0.037 Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 125 °C mA IAC,max Ordering code 100 kHz (composition see 105 °C below) mA 0.702 0.702 0.702 0.702 0.702 0.702 0.702 0.702 0.702 0.702 0.540 0.453 0.380 0.319 0.268 0.225 0.203 0.115 0.115 0.062 0.062 0.055 0.055 0.033 0.033 0.034 35 50 70 100 200 200 200 200 260 260 300 300 440 440 440 440 680 965 965 1205 1205 1820 1820 2280 2280 2280 46 65 91 130 260 260 260 260 338 338 390 390 572 572 572 572 884 1255 1255 1566 1566 2366 2366 2964 2964 2964 B41896C6105M*** B41896C6225M*** B41896C6335M*** B41896C6475M*** B41896C6106M*** B41896C6126M*** B41896C6156M*** B41896C6186M*** B41896C6226M*** B41896C6276M*** B41896C6336M*** B41896C6396M*** B41896C6476M*** B41896C6566M*** B41896C6686M*** B41896C6826M*** B41896C6107M*** B41896C6127M*** B41896C6157M*** B41896C6187M*** B41896C6227M*** B41896C6277M*** B41896C6337M*** B41896C6397M*** B41896C6477M*** B41896D6477M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 11 of 32 B41896 Extra long useful life 125 °C Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm ESRmax 10 kHz 40 °C Ω ESRmax 120 Hz 20 °C Ω VR = 50 V DC 560 16 × 20 0.299 680 16 × 25 0.238 680 18 × 20 0.273 820 16 × 31.5 0.185 1000 16 × 31.5 0.185 1200 18 × 31.5 0.178 1500 18 × 35 0.178 1800 18 × 40 0.150 VR = 63 V DC 22 8 × 11.5 24.600 33 8 × 11.5 24.600 47 10 × 12.5 7.963 68 10 × 16 5.097 100 10 × 20 3.434 150 12.5 × 20 2.522 180 12.5 × 20 2.522 220 12.5 × 25 1.671 270 12.5 × 25 1.671 330 12.5 × 25 1.671 390 12.5 × 30 1.422 470 16 × 25 1.522 560 16 × 31.5 1.219 680 16 × 31.5 1.341 820 18 × 31.5 1.108 1000 18 × 35 0.936 1200 18 × 40 0.840 ESRmax 10 kHz 20 °C Ω Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 125 °C mA IAC,max Ordering code 100 kHz (composition see 105 °C below) mA 0.226 0.186 0.186 0.154 0.100 0.095 0.084 0.070 0.037 0.030 0.034 0.023 0.023 0.022 0.022 0.019 0.034 0.026 0.031 0.022 0.022 0.021 0.019 0.016 2280 2860 2490 3160 3160 3500 3840 4230 2964 3718 3237 4108 4108 4550 4992 5499 B41896C6567M*** B41896C6687M*** B41896D6687M*** B41896C6827M*** B41896C6108M*** B41896C6128M*** B41896C6158M*** B41896C6188M*** 8.612 5.742 4.031 2.786 1.895 1.263 1.053 0.861 0.702 0.574 0.486 0.403 0.338 0.279 0.231 0.189 0.158 2.460 2.460 0.796 0.510 0.343 0.252 0.252 0.167 0.167 0.167 0.142 0.152 0.122 0.134 0.111 0.094 0.084 2.160 2.160 0.711 0.435 0.325 0.243 0.243 0.155 0.155 0.155 0.134 0.143 0.109 0.120 0.099 0.085 0.080 147 147 297 416 525 695 695 950 950 950 1103 1120 1403 1338 1581 1775 1936 191 191 386 540 682 903 903 1236 1236 1236 1433 1455 1824 1739 2055 2307 2516 B41896C8226M*** B41896C8336M*** B41896C8476M*** B41896C8686M*** B41896C8107M*** B41896C8157M*** B41896C8187M*** B41896C8227M*** B41896C8277M*** B41896C8337M*** B41896C8397M*** B41896C8477M*** B41896C8567M*** B41896C8687M*** B41896C8827M*** B41896C8108M*** B41896C8128M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 12 of 32 B41896 Extra long useful life 125 °C Useful life depending on ambient temperature TA under ripple current operating conditions1) VR ≤ 50 V, d = 8 mm VR ≤ 50 V, d = 10 mm 1) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life graphs. Please read Cautions and warnings and Important notes at the end of this document. Page 13 of 32 B41896 Extra long useful life 125 °C Useful life depending on ambient temperature TA under ripple current operating conditions2) VR ≤ 50 V, d ≥ 12.5 mm VR = 63 V, d = 8 mm 2) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life graphs. Please read Cautions and warnings and Important notes at the end of this document. Page 14 of 32 B41896 Extra long useful life 125 °C Useful life depending on ambient temperature TA under ripple current operating conditions3) VR = 63 V, d = 10 mm VR = 63 V, d ≥ 12.5 3) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life graphs. Please read Cautions and warnings and Important notes at the end of this document. Page 15 of 32 B41896 Extra long useful life 125 °C Frequency factor of permissible ripple current IAC versus frequency f Please read Cautions and warnings and Important notes at the end of this document. Page 16 of 32 B41896 Extra long useful life 125 °C Taping, packing and lead configurations Taping Single-ended capacitors are available taped in Ammo pack from diameter 5 to 18 mm as follows: Lead spacing F = 2.5 mm (∅ d = 5 … 6.3 mm) Lead spacing F = 3.5 mm (∅ d = 8 mm) Lead spacing F = 5.0 mm (∅ d = 5 … 12.5 mm) Lead spacing F = 7.5 mm (∅ d = 16 ... 18 mm). Lead spacing 2.5 mm (∅ d = 5 ... 6.3 mm) Last 3 digits of ordering code: 007 Dimensions in mm ∅d 5 F H W W0 W1 W2 H0 P P0 P1 I1 t ∆h D0 2.5 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 5.1 1.0 0.7 1.0 4.0 6.3 Toler- +0.8 ±0.75 ±0.5 min. ±0.5 max. ±0.5 ±1.0 ±0.2 ±0.5 max. ±0.2 max. ±0.2 ance 02 Please read Cautions and warnings and Important notes at the end of this document. Page 17 of 32 B41896 Extra long useful life 125 °C Lead spacing 3.5 mm (∅ d = 8 mm) Last 3 digits of ordering code: 006 Dimensions in mm ∅d 8 Tolerance F H W W0 W1 W2 P P0 P1 I1 t ∆h 3.5 18.5 18.0 12.5 9.0 1.5 12.7 12.7 4.6 1.0 0.7 1.0 +0.8 02 1.0 ±0.5 min. ±0.5 max. ±1.0 ±0.2 ±0.5 max. ±0.2 Please read Cautions and warnings and Important notes at the end of this document. Page 18 of 32 D0 4.0 max. ±0.2 B41896 Extra long useful life 125 °C Lead spacing 5.0 mm (∅ d = 5 ... 8 mm) Last 3 digits of ordering code: 008 Lead spacing 5.0 mm (∅ d = 10 ... 12.5 mm) Last 3 digits of ordering code: 008 Dimensions in mm ∅d 5 6.3 F H W W0 W1 W2 H0 P P0 P1 I1 t ∆h D0 5.0 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 3.85 1.0 0.7 1.0 4.0 16.0 12.7 12.7 3.85 18.0 12.5 9.0 1.5 12.7 12.7 3.85 1.0 0.7 1.0 4.0 15.0 15.0 5.0 ±1.0 ±0.2 ±0.5 8 10 20.0 5.0 12.5 Toler- +0.8 ance 02 19.0 19.0 ±0.75 ±0.5 min. ±0.5 max. ±0.5 Please read Cautions and warnings and Important notes at the end of this document. Page 19 of 32 max. ±0.2 max. ±0.2 B41896 Extra long useful life 125 °C Lead spacing 7.5 mm (∅ d = 16 ...18 mm) Last 3 digits of ordering code: 009 Dimensions in mm ∅d 16 F H W 7.5 18.5 18.0 18 *) Toler0.5 ±0.8 ±0.5 ance +0.75 W0 W1 W2 P P0 P1 I1 t ∆P ∆h D0 12.5 9.0 1.5 30.0 15.0 3.75 1.0 0.7 0 0 4.0 min. ±0.5 max. ±1.0 ±0.2 ±0.5 max. ±0.2 ±1.0 ±1.0 ±0.2 *) Available only for case dimensions 18 × 20, 18 × 25 and 18 × 31.5 mm Please read Cautions and warnings and Important notes at the end of this document. Page 20 of 32 B41896 Extra long useful life 125 °C Packing units and box dimensions Ammo pack Please read Cautions and warnings and Important notes at the end of this document. Case size d×l mm Dimensions (mm) Amax Bmax Cmax 5 × 11 345 55 240 2000 6.3 × 11 345 55 290 2000 8 × 11.5 345 55 240 1000 10 × 12.5 345 55 280 750 10 × 16 345 60 200 500 10 × 20 345 60 200 500 12.5 × 20 345 65 280 500 12.5 × 25 345 65 280 500 12.5 × 25 345 65 280 500 12.5 × 30 345 65 275 500 16 × 20 315 65 275 300 16 × 25 315 65 275 300 16 × 31.5 315 65 275 300 18 × 20 315 65 275 250 18 × 25 315 65 275 250 18 × 31.5 315 65 275 250 Page 21 of 32 Packing units pcs. B41896 Extra long useful life 125 °C Kinked or cut leads Single-ended capacitors are available with kinked or cut leads. Other lead configurations also available upon request. Kinked leads Last 3 digits of ordering code: 001 With stand-off rubber seal Case size d × l (mm) With flat rubber seal Please read Cautions and warnings and Important notes at the end of this document. Page 22 of 32 Dimensions (mm) a ±0.5 10 × 20 5.0 12.5 × 20 5.0 12.5 × 25 5.0 12.5 × 30 5.0 12.5 × 35 5.0 12.5 × 40 5.0 16 × 20 7.5 16 × 25 7.5 16 × 31.5 7.5 18 × 20 7.5 18 × 25 7.5 18 × 31.5 7.5 18 × 35 7.5 18 × 40 7.5 20 × 20 10.0 20 × 25 10.0 20 × 40 10.0 22 × 30 10.0 22 × 35 10.0 22 × 40 10.0 B41896 Extra long useful life 125 °C Cut leads Last 3 digits of ordering code: 002 With stand-off rubber seal Case size d × l (mm) With flat rubber seal Please read Cautions and warnings and Important notes at the end of this document. Page 23 of 32 Dimensions (mm) a ±0.5 10 × 12.5 5.0 10 × 16 5.0 10 × 20 5.0 12.5 × 20 5.0 12.5 × 25 5.0 12.5 × 30 5.0 12.5 × 35 5.0 12.5 × 40 5.0 16 × 20 7.5 16 × 25 7.5 16 × 31.5 7.5 18 × 20 7.5 18 × 25 7.5 18 × 31.5 7.5 18 × 35 7.5 18 × 40 7.5 20 × 20 10.0 20 × 25 10.0 20 × 40 10.0 B41896 Extra long useful life 125 °C PAPR leads (Protection Against Polarity Reversal) These lead configurations ensure correct placement of the capacitor on the PCB with regard to polarity. PAPR leads are available for diameters from 10 mm up to 20 mm. There are three configurations available: Crimped leads, J leads, bent 90° leads Crimped leads Last 3 digits of ordering code: 003 With stand-off rubber seal With flat rubber seal Suggestion for PCB hole diameter Case size d × l (mm) Dimensions (mm) B ±0.2 C ±0.5 D ±0.1 E ±0.1 16 × 20 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05 16 × 25 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05 16 × 31.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05 18 × 20 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1 18 × 25 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1 18 × 31.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1 18 × 35 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1 18 × 40 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1 20 × 20 1.5 3.0 1.6 0.3 10.0 1.0 ±0.1 20 × 25 1.5 3.0 1.6 0.3 10.0 1.0 ±0.1 20 × 40 1.5 3.0 1.6 0.3 10.0 1.0 ±0.1 Please read Cautions and warnings and Important notes at the end of this document. Page 24 of 32 a ±0.5 ∅b B41896 Extra long useful life 125 °C J leads Last 3 digits of ordering code: 004 Suggestion for PCB hole diameter Case size d × l (mm) Dimensions (mm) C ±0.5 E ±0.5 J ±0.2 10 × 12.5 3.2 0.7 1.2 5.0 0.6 ±0.05 10 × 16 3.2 0.7 1.2 5.0 0.6 ±0.05 10 × 20 3.2 0.7 1.2 5.0 0.6 ±0.05 12.5 × 20 3.2 0.7 1.2 5.0 0.6 ±0.05 12.5 × 25 3.2 0.7 1.2 5.0 0.6 ±0.05 16 × 20 3.5 0.7 1.6 7.5 0.8 ±0.05 16 × 25 3.5 0.7 1.6 7.5 0.8 ±0.05 16 × 31.5 3.5 0.7 1.6 7.5 0.8 ±0.05 18 × 20 3.5 0.7 1.6 7.5 0.8 ±0.1 18 × 25 3.5 0.7 1.6 7.5 0.8 ±0.1 18 × 31.5 3.5 0.7 1.6 7.5 0.8 ±0.1 18 × 35 3.5 0.7 1.6 7.5 0.8 ±0.1 Please read Cautions and warnings and Important notes at the end of this document. Page 25 of 32 a ±0.5 ∅b B41896 Extra long useful life 125 °C Bent 90° leads for horizontal mounting pinning Last 3 digits of ordering code: 012 Case size d × l (mm) Dimensions (mm) C ±0.5 E ±0.5 F ±0.5 a ±0.5 ∅b 16 × 20 4.0 4.0 12.0 7.5 0.8 ±0.05 16 × 25 4.0 4.0 12.0 7.5 0.8 ±0.05 16 × 31.5 4.0 4.0 12.0 7.5 0.8 ±0.05 18 × 20 4.0 4.0 13.0 7.5 0.8 ±0.1 18 × 25 4.0 4.0 13.0 7.5 0.8 ±0.1 18 × 31.5 4.0 4.0 13.0 7.5 0.8 ±0.1 18 × 35 4.0 4.0 13.0 7.5 0.8 ±0.1 18 × 40 4.0 4.0 13.0 7.5 0.8 ±0.1 Bent leads for diameter 12.5 mm available upon request. Please read Cautions and warnings and Important notes at the end of this document. Page 26 of 32 B41896 Extra long useful life 125 °C Overview of packing units and code numbers for case sizes 5 × 11 ... 16 × 31.5 PAPR Case size d×l Taped, Ammo pack mm Standard, bulk pcs. 5 × 11 2000 6.3 × 11 2500 2000 8 × 11.5 1000 1000 10 × 12.5 1000 750 10 × 16 100 500 1000 10 × 20 500 500 500 500 12.5 × 20 350 500 350 350 12.5 × 25 250 500 500 500 12.5 × 30 200 500 175 175 12.5 × 35 175 - 175 175 12.5 × 40 175 - 175 175 16 × 20 250 300 200 200 16 × 25 250 300 200 16 × 31.5 200 300 The last three digits of the complete ordering code state the lead configuration 000 Code 006 007 008 009 1) pcs. Kinked leads, bulk pcs. Cut Crimped J leads leads, leads bulk pcs. pcs. pcs. 2000 F (mm) d (mm) 3.5 2.5 5 7.5 1000 675 675 500 300 1) 225 1) 180 1) 150 1) 150 1) 200 200 120 200 200 200 120 250 250 344 344 120 001 002 003 004 012 8 5...6.3 5...12.5 16...18 Available upon request Please read Cautions and warnings and Important notes at the end of this document. Bent 90° leads, blister pcs. Page 27 of 32 B41896 Extra long useful life 125 °C Overview of packing units and code numbers for case sizes 18 × 20 ... 25 × 40 PAPR Case size d×l Taped, Ammo pack mm Standard, bulk pcs. pcs. Kinked leads, bulk pcs. Cut Crimped J leads leads, leads bulk pcs. pcs. pcs. Bent 90° leads, blister pcs. 18 × 20 175 18 × 25 150 250 175 175 200 200 120 250 150 150 200 200 18 × 31.5 120 100 250 100 100 150 150 120 18 × 35 100 100 100 150 150 150 18 × 40 125 100 100 120 72 20 × 20 125 125 125 200 20 × 25 125 125 125 200 20 × 30 100 100 100 120 20 × 35 100 100 100 120 20 × 40 100 100 100 120 22 × 30 80 100 100 22 × 35 80 100 100 22 × 40 80 100 100 25 × 40 40 100 The last three digits of the complete ordering code state the lead configuration 000 Code 007 008 009 001 002 Please read Cautions and warnings and Important notes at the end of this document. F (mm) d (mm) 2.5 5 7.5 4...6.3 6.3...12.5 16...18 Page 28 of 32 003 004 012 B41896 Extra long useful life 125 °C Cautions and warnings Personal safety The electrolytes used by EPCOS have not only been optimized with a view to the intended application, but also with regard to health and environmental compatibility. They do not contain any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide (DMAC). Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They contain flame-retarding substances which will quickly extinguish any flame that may have been ignited. As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce operating electrolytes. However, in exceptional cases, such materials must be used in order to achieve specific physical and electrical properties because no safe substitute materials are currently known. However, the amount of dangerous materials used in our products has been limited to an absolute minimum. Nevertheless, the following rules should be observed when handling Al electrolytic capacitors: Any escaping electrolyte should not come into contact with eyes or skin. If electrolyte does come into contact with the skin, wash the affected parts immediately with running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If symptoms persist, seek medical treatment. Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be well ventilated. Clothing that has been contaminated by electrolyte must be changed and rinsed in water. Please read Cautions and warnings and Important notes at the end of this document. Page 29 of 32 B41896 Extra long useful life 125 °C Product safety The table below summarize the safety instructions that must be observed without fail. A detailed description can be found in the relevant sections of chapter "General technical information". Topic Safety information Polarity Make sure that polar capacitors are connected with the right polarity. Reverse voltage Voltages polarity classes should be prevented by connecting a diode. Do not exceed the upper category temperatur. Upper category temperature Maintenance Mounting position of screw terminal capacitors Mounting of single-ended capacitors Robustness of terminals Soldering Make periodic inspections of the capacitors. Before the inspection, make sure that the power supply is turned off and carefully discharge the electricity of the capacitors. Do not apply any mechanical stress to the capacitor terminals. Do not mount the capacitor with the terminals (safety vent) upside down. Reference Chapter "General technical information" 1 "Basic construction of aluminum electrolytic capacitors" 3.1.6 "Reverse voltage" 7.2 "Maximum permissible operating temperature" 10 "Maintenance" 11.1. "Mounting positions of capacitors with screw terminals" The internal structure of single-ended capacitors 11.4 might be damaged if excessive force is applied to "Mounting the lead wires. considerations for Avoid any compressive, tensile or flexural stress. single-ended capacitors" Do not move the capacitor after soldering to PC board. Do not pick up the PC board by the soldered capacitor. Do not insert the capacitor on the PC board with a hole space different to the lead space specified. The following maximum tightening torques must 11.3 not be exceeded when connecting screw "Mounting torques" terminals: M5: 2 Nm M6: 2.5 Nm Do not exceed the specified time or temperature 11.5 limits during soldering. "Soldering" Please read Cautions and warnings and Important notes at the end of this document. Page 30 of 32 B41896 Extra long useful life 125 °C Topic Soldering, cleaning agents Passive flammability Active flammability Safety information Reference Chapter "General technical information" Do not allow halogenated hydrocarbons to come 11.6 into contact with aluminum electrolytic capacitors. "Cleaning agents" Avoid external energy, such as fire or electricity. 8.1 "Passive flammability" Avoid overload of the capacitors. 8.2 "Active flammability" Breakdown strength Do not damage the insulating sleeve, especially of insulating when ring clips are used for mounting. sleeves Please read Cautions and warnings and Important notes at the end of this document. Page 31 of 32 Reference Chapter "Capacitors with screw terminals" "Screw terminals accessories" Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of passive electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of a passive electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of a passive electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as “hazardous”). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, EPCOS-JONES, BAOKE, Alu-X, CeraDiode, CSSP, MLSC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K, UltraCap, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 32 of 32