SPECIFICATION FOR APPROVAL PAGE: 1 REF : PROD. NAME ABC'S DWG NO. SMD POWER INDUCTOR ESR0403□□□□L□-□□□ ABC'S ITEM NO. Ⅰ﹒CONFIGURATION & DIMENSIONS： B 100 A A : 4.5±0.3 m/m B : 4.0±0.3 m/m C : 3.2±0.3 m/m D : 1.2 ref. m/m G : 1.5 ref. m/m H : 4.5 ref. m/m 5.0 ref. m/m C I : H D G I ( PCB Pattern ) Ⅱ﹒SCHEMATIC DIAGRAM： a b Ⅲ﹒MATERIALS： a﹒Core：Ferrite DR core b﹒Wire ：Enamelled copper wire (Class F & H) c c﹒Terminal： Ag/Ni/Sn Peak Temp：245±5℃ d﹒Remark：Products comply with RoHS' requirements Max time above 200℃ ：60sec max. Ⅳ﹒GENERAL SPECIFICATION： b﹒Operating temp.：-40℃----+105℃ c﹒Resistance to solder heat：245±5℃.10 secs. 150 ~ 200℃ / 60 ~ 120sec Reflow Area +2.0 ~ 4.0℃ / sec max. Forced Cooling Area -(1.0 ~ 5.0)℃ / sec max. P eak Temperature: 245±5℃ 200 150 60sec max. 100 50 0 AR-001A Preheat Area +4.0℃ / sec max. 250 Temperature ( ℃ ) a﹒Storage temp.：-40℃ ----+125℃ Temperature Rising Area 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL REF : PAGE: 2 PROD. NAME ABC'S DWG NO. SMD POWER INDUCTOR ESR0403□□□□L□-□□□ ABC'S ITEM NO. Ⅴ﹒ELECTRICAL CHARACTERISTICS： DWG No. Inductance ( μH ) ESR04031R0ML□-□□□ ESR04032R2ML□ -□□□ ESR04033R3ML□ -□□□ ESR04034R7ML□-□□□ ESR04036R8ML□ -□□□ ESR04038R2ML□ -□□□ ESR0403100ML□ -□□□ ESR0403120ML□ -□□□ ESR0403150ML□ -□□□ ESR0403180ML□ -□□□ ESR0403220ML□ -□□□ ESR0403270ML□ -□□□ ESR0403330KL□ -□□□ ESR0403390KL□ -□□□ ESR0403470KL□ -□□□ ESR0403560KL□ -□□□ ESR0403680KL□ -□□□ 1.0±20% 2.2±20% 3.3±20% 4.7±20% 6.8±20% 8.2±20% 10.0±20% 12.0±20% 15.0±20% 18.0±20% 22.0±20% 27.0±20% 33.0±10% 39.0±10% 47.0±10% 56.0±10% 68.0±10% RDC ( mΩ ) typ. max. 19.3 31.8 46.9 64.5 93.6 106.0 127.0 146.0 192.0 237.0 270.0 322.0 373.0 449.0 505.0 736.0 822.0 48 71 86 108 126 142 172 197 259 309 351 419 485 561 631 920 1028 Rated Current (A) 2.70 2.30 2.00 1.65 1.45 1.40 1.05 1.00 0.85 0.75 0.70 0.65 0.60 0.55 0.50 0.45 0.40 1). □：Packaging information… A：Bulk B：Taping Reel 2)."":Reference code 3). Inductance test condition :1MHz/1V 4). Rated current: The DC current at which the inductance decreases to 90% of it's initial value or when Δt=40℃,whichever is lower(Ta=20℃) □□□ AR-001A SRF (MHz) ref. 113 76 64 50 41 38 36 32 29 28 25 22 20 18 16 15 13 SPECIFICATION FOR APPROVAL PAGE: 3 REF : PROD. ABC'S DWG NO. SMD POWER INDUCTOR NAME ESR0403□□□□L□-□□□ ABC'S ITEM NO. Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover tape N B A 2.0±0.5 ∮C ∮C D G Embossed carrier ※Carrier tape width : D P:8 m/m 4 m/m Start End 100 100 Leadr no component 200 m/m min. 100 100 100 100 Trailer no component 400 m/m min. Components User direction of feed ( 2 ) Dimensions Unit:m/m Style A B 13 - 12 330 21±0.8 C 13±0.5 D 12 G 14 +0 N 50 -0 T 18.4 ( 3 ) Q'TY & G.W. Per package Inner : Reel Outer : Carton Series Q'TY (pcs) ESR0403 AR-001A 2000 G.W. (gw) 1100 Style 13 - 12 Q'TY (pcs) 16,000 G.W. (Kg) 11.9 Size (cm) 40 x 40 x 24 SPECIFICATION FOR APPROVAL REF : PROD. ABC'S DWG NO. SMD POWER INDUCTOR NAME PAGE: 4 ESR0403□□□□L□-□□□ ABC'S ITEM NO. Ⅶ﹒DWGING NUMBER EXPRESSION： E S R 0 4 0 3 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code E : Economy Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code AR-001A Inner package A T.B.D. B T / R ( Reel package ) Inner package Q'TY T.B.D. 2,000 pcs Remark SPECIFICATION FOR APPROVAL PAGE: 5 REF : PROD. NAME SMD POWER INDUCTOR ESR0403□□□□L□-□□□ ABC'S DWG NO. ABC'S ITEM NO. Ⅷ﹒RELIABILITY TEST： Test item Solderability Thermal shock test ( Temp. cycle ) Specification Test condition More than 95% of the terminal electrode Shall be covered With fresh solder. Preheat : 155℃ / 4 hours. Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 235±5℃ Flux : Rosin Dip time : 5±0.5 seconds Electrical oharacteristics shall not change more than ±20% Room temp. 15 minutes -40 ℃ 30 minutes Room temp. 15 minutes +105 ℃ Total : 50 cycles Humidity test Temperature : 40±2℃ Humidity : 90±5% Time : 1000 hours High temp. Resistance test Temperature : 105±5℃ Applied current : Per spec. Time : 96 hours AR-001A 30 minutes SPECIFICATION FOR APPROVAL REF : PAGE: 6 PROD. NAME ESR0403□□□□L□-□□□ ABC'S DWG NO. SMD POWER INDUCTOR ABC'S ITEM NO. Ⅸ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ BC Coat Typ Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyamideimide Polyamide Modified Epoxy ____ ____ Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Polyamide ____ ____ ____ ____Nylon ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ Modified Polyester Polyurethane SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 ANSI Type Temp Class MW81-C MW75C MW35C ___ ___ 220 130 200 180 200 ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ Mark Dsg ____ ____ ____ ____ ____ ____ 220 200 155 155 130 155 155 155 180 155 155 155 180 180 MW26C MW79 155 155 A not-for-profit organization dedicated to public safety and committed to quality service Page 1 of 2 287806002 Mtl Dsg OC ____ ____ E174837 Coat Typ BC OC Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyamide ____ ____ ____ Nylon Polyamide ANSI Type Temp Class MW80C MW2-C ___ 155 105 130 130 130 130 MW75C MW28-C MW28-C @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks Recognized Component Mark. or 榮星電線 , material designation or marked designation on packaed or reel, and See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 AR-001A Page 2 of 2 OBMW2⁄E174837 September 8 , 2000 SPECIFICATION FOR APPROVAL REF : PROD. PAGE: 7 ABC'S DWG NO. SMD POWER INDUCTOR NAME ESR0403□□□□L□-□□□ ABC'S ITEM NO. OBMW2 Magnet Wire-Comporent October 06, 2005 E143312 ELEKTRISOLA (MALAYSLA) SDN BHD JALAN DAMAI SATU JANDA BAIK 28750 BENTONG, PAHANG DARUL MAKMUR MALAYSIA Coating Type Mtl Dsg Estersol 180 Mark Dsg E180 BC Amldester 200 Polysol-N 155 A200 PN155 Polyesterimide (solderable) Polyesterimide Polyurechane Polysol 155 P155, G155 Polyurechane Polysol 155g Polysol 155p Polysol 160 Polysol 180 Pg155 Pp155,Gp155 P160 P180,G180 Polyurechane Polyurechane Polyurechane Polyurechane Polysol 170 Polysol-N 180 Polysol P155p P170 or G170 PN180 P155p Polyurechane Polyurechane OC ____ ____ Nylon ____ ____ ____ ____ ____ ____ Nylon ____ ANSI Typ Temp Class MW-77 180 MW-74 MW-80, MW-28 MW-79, MW-75 MW-75 MW-79 MW-79 MW-82 MW-79 MW-79 MW-83 MW-79 200 155, 130 155, 130 130 155 155 180 155 155 180 155 Marking：Company name, material designation or marked designation and factory identification on package ok reel See General Information preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. AR-001A