Order Now Product Folder Support & Community Tools & Software Technical Documents LMK60E2-125M, LMK60E2-156M, LMK60E0-156M LMK60E0-212M, LMK60I2-100M, LMK60I2-322M SNAS718B – DECEMBER 2016 – REVISED OCTOBER 2017 LMK60XX High Performance Low Jitter Oscillator 1 Features 3 Description • The LMK60EX is a family of low jitter oscillators that generate a commonly used reference clock. The device is pre-programmed in factory to support any reference clock frequency; supported output formats are LVPECL, LVDS, and HCSL up to 400 MHz. Internal power conditioning provide excellent power supply ripple rejection (PSRR), reducing the cost and complexity of the power delivery network. The device operates from a single 3.3-V ±5% supply. 1 • • • • • Low Noise, High Performance – Jitter: 150 fs RMS Typical Fout > 100 MHz – PSRR: –60 dBc, Robust Supply Noise Immunity Supported Output Format – LVPECL, LVDS and HCSL up to 400 MHz Total Frequency Tolerance of ±50 ppm (LMK60X2) and ±25 ppm (LMK60X0) 3.3-V Operating Voltage Industrial Temperature Range (–40ºC to +85ºC) 7-mm × 5-mm 6-pin Package That is PinCompatible With Industry Standard 7050 XO Package Device Information(1) PART NUMBER PACKAGE SIZE LMK60E2-125M QFM (6) 7.00 mm × 5.00 mm LMK60E2-156M QFM (6) 7.00 mm × 5.00 mm LMK60E0-156M QFM (6) 7.00 mm × 5.00 mm LMK60E0-212M QFM (6) 7.00 mm × 5.00 mm 2 Applications LMK60I2-100M QFM (6) 7.00 mm × 5.00 mm • LMK60I2-322M QFM (6) 7.00 mm × 5.00 mm • • • • High-Performance Replacement for Crystal-, SAW-, or Silicon-Based Oscillators Switches, Routers, Network Line Cards, Base Band Units (BBU), Servers, Storage/SAN Test and Measurement Medical Imaging FPGA, Processor Attach (1) For all available packages, see the orderable addendum at the end of the data sheet. Output Frequency Options OUTPUT FREQ (MHz) AND FORMAT TOTAL FREQ STABILITY (ppm) LMK60E2-125M 125 LVPECL ±50 LMK60E2-156M 156.25 LVPECL ±50 LMK60E0-156M 156.25 LVPECL ±25 LMK60E0-212M 212.5 LVPECL ±25 LMK60I2-100M 100 HCSL ±50 LMK60I2-322M 322.265625 HCSL ±50 PART NUMBER Pinout 6 OE 1 6 VDD NC 2 5 OUTN GND 3 4 OUTP 1 2 5 4 3 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LMK60E2-125M, LMK60E2-156M, LMK60E0-156M LMK60E0-212M, LMK60I2-100M, LMK60I2-322M SNAS718B – DECEMBER 2016 – REVISED OCTOBER 2017 www.ti.com Table of Contents 1 2 3 4 5 6 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 3 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 6.10 3 3 4 4 4 4 5 5 5 5 Absolute Maximum Ratings ...................................... ESD Ratings ............................................................ Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics - Power Supply ................. LVPECL Output Characteristics................................ LVDS Output Characteristics .................................... HCSL Output Characteristics.................................... OE Input Characteristics ........................................... Frequency Tolerance Characteristics ..................... 6.11 6.12 6.13 6.14 Power-On/Reset Characteristics (VDD).................. PSRR Characteristics ............................................. PLL Clock Output Jitter Characteristics .................. Additional Reliability and Qualification .................... 6 6 6 6 7 Parameter Measurement Information .................. 7 8 9 Power Supply Recommendations........................ 9 Layout ..................................................................... 9 7.1 Device Output Configurations ................................... 7 9.1 Layout Guidelines ..................................................... 9 10 Device and Documentation Support ................. 11 10.1 10.2 10.3 10.4 10.5 Receiving Notification of Documentation Updates Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 11 11 11 11 11 11 Mechanical, Packaging, and Orderable Information ........................................................... 11 4 Revision History Changes from Revision A (June 2017) to Revision B Page • New release of LMK60E2-125M............................................................................................................................................. 1 • New release of LMK60I2-100M .............................................................................................................................................. 1 • New release of LMK60I2-322M ............................................................................................................................................. 1 Changes from Original (December 2016) to Revision A • 2 Page Added LMK60E0-156M and LMK60E0-212M ....................................................................................................................... 1 Submit Documentation Feedback Copyright © 2016–2017, Texas Instruments Incorporated Product Folder Links: LMK60E2-125M LMK60E2-156M LMK60E0-156M LMK60E0-212M LMK60I2-100M LMK60I2322M LMK60E2-125M, LMK60E2-156M, LMK60E0-156M LMK60E0-212M, LMK60I2-100M, LMK60I2-322M www.ti.com SNAS718B – DECEMBER 2016 – REVISED OCTOBER 2017 5 Pin Configuration and Functions SIA Package 6-pin QFM Top View OE 1 6 VDD NC 2 5 OUTN GND 3 4 OUTP Pin Functions PIN NAME I/O NO. DESCRIPTION POWER GND 3 Ground Device ground VDD 6 Analog 3.3-V power supply 4, 5 Universal OUTPUT BLOCK OUTP, OUTN Differential output pair (LVPECL, LVDS or HCSL). DIGITAL CONTROL / INTERFACES NC 2 N/A OE 1 LVCMOS No connect Output enable (internal pullup). When set to low, output pair is disabled and set at high impedance. 6 Specifications 6.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) MIN MAX UNIT VDD Device supply voltage –0.3 3.6 V VIN Output voltage for logic inputs –0.3 VDD + 0.3 V VOUT Output voltage for clock outputs –0.3 VDD + 0.3 V TJ Junction temperature 150 °C TSTG Storage temperature 125 °C (1) –40 Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute maximum-rated conditions for extended periods may affect device reliability. 6.2 ESD Ratings VALUE V(ESD) (1) (2) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) ±2000 Charged-device model (CDM), per JEDEC specification JESD22-C101 (2) ±500 UNIT V JEDEC document JEP155 states that 500 V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 250 V CDM allows safe manufacturing with a standard ESD control process. Copyright © 2016–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMK60E2-125M LMK60E2-156M LMK60E0-156M LMK60E0-212M LMK60I2-100M LMK60I2322M 3 LMK60E2-125M, LMK60E2-156M, LMK60E0-156M LMK60E0-212M, LMK60I2-100M, LMK60I2-322M SNAS718B – DECEMBER 2016 – REVISED OCTOBER 2017 www.ti.com 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) VDD Device supply voltage TA Ambient temperature TJ Junction temperature tRAMP VDD power-up ramp time MIN NOM MAX 3.135 3.3 3.465 V –40 25 85 °C 0.1 UNIT 105 °C 100 ms 6.4 Thermal Information (2) (3) (4) LMK60EX SIA (QFM) THERMAL METRIC (1) UNIT 6 PINS Airflow (LFM) 0 RθJA Junction-to-ambient thermal resistance 74.8 °C/W RθJC(top) Junction-to-case (top) thermal resistance 46.7 °C/W RθJB Junction-to-board thermal resistance 49.0 °C/W ψJT Junction-to-top characterization parameter 14.8 °C/W ψJB Junction-to-board characterization parameter 48.7 °C/W RθJC(bot) Junction-to-case (bottom) thermal resistance n/a °C/W (1) (2) (3) (4) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report. The package thermal resistance is calculated on a 4 layer JEDEC board. Connected to GND with 2 thermal vias (0.3-mm diameter). ψJB (junction to board) is used when the main heat flow is from the junction to the GND pad. Please refer to Thermal Considerations section for more information on ensuring good system reliability and quality. 6.5 Electrical Characteristics - Power Supply (1) VDD = 3.3 V ± 5%, TA = -40C to 85°C PARAMETER IDD Device current consumption Device current consumption when output is disabled IDD-PD (1) (2) (3) TEST CONDITIONS TYP MAX LVPECL (2) MIN 95 110 LVDS 85 100 HCSL (3) 90 105 OE = GND 70 UNIT mA mA Refer to Parameter Measurement Information for relevant test conditions. On-chip power dissipation should exclude 40 mW, dissipated in the 150 Ω termination resistors, from total power dissipation. Excludes load current. 6.6 LVPECL Output Characteristics (1) VDD = 3.3 V ± 5%, TA = -40C to 85°C PARAMETER fOUT Output frequency (2) VOD Output voltage swing (VOH – VOL) (2) VOUT, DIFF, PP Differential output peak-to-peak swing VOS Output common-mode voltage tR / tF Output rise/fall time (20% to 80%) (3) ODC Output duty cycle (3) (1) (2) (3) 4 TEST CONDITIONS MIN TYP 700 950 MAX UNIT 400 MHz 1200 mV 2 × |VOD| V VDD – 1.45 260 45% V 350 ps 55% Refer to Parameter Measurement Information for relevant test conditions. An output frequency over fOUT max spec is possible, but output swing may be less than VOD min spec. Ensured by characterization. Submit Documentation Feedback Copyright © 2016–2017, Texas Instruments Incorporated Product Folder Links: LMK60E2-125M LMK60E2-156M LMK60E0-156M LMK60E0-212M LMK60I2-100M LMK60I2322M LMK60E2-125M, LMK60E2-156M, LMK60E0-156M LMK60E0-212M, LMK60I2-100M, LMK60I2-322M www.ti.com SNAS718B – DECEMBER 2016 – REVISED OCTOBER 2017 6.7 LVDS Output Characteristics (1) VDD = 3.3 V ± 5%, TA = -40°C to 85°C PARAMETER TEST CONDITIONS fOUT Output frequency VOD Output voltage swing (VOH – VOL) (1) VOUT, DIFF, PP Differential output peak-to-peak swing VOS Output common-mode voltage tR / tF Output rise/fall time (20% to 80%) ODC Output duty cycle (2) ROUT Differential output impedance (1) (2) MIN TYP 300 390 (1) MAX UNIT 400 MHz 480 mV 2 x |VOD| V 1.2 V (2) 260 350 45% ps 55% 107 Ω An output frequency over fOUT max spec is possible, but output swing may be less than VOD min spec. Ensured by characterization. 6.8 HCSL Output Characteristics (1) VDD = 3.3 V ± 5%, TA = -40°C to 85°C PARAMETER TEST CONDITIONS MIN TYP MAX UNIT fOUT Output frequency 400 MHz VOH Output high voltage 660 900 mV VOL Output low voltage –100 100 mV 250 475 mV 0 140 mV 1 3 V/ns 45% 55% VCROSS Absolute crossing voltage (2) (3) VCROSS-DELTA Variation of VCROSS (2) (3) dV/dt Slew rate (4) ODC Output duty cycle (4) (1) (2) (3) (4) Refer to Parameter Measurement Information for relevant test conditions. Measured from –150 mV to +150 mV on the differential waveform with the 300 mVpp measurement window centered on the differential zero crossing. Ensured by design. Ensured by characterization. 6.9 OE Input Characteristics VDD = 3.3 V ± 5%, TA = -40°C to 85°C PARAMETER TEST CONDITIONS MIN VIH Input high voltage VIL Input low voltage IIH Input high current VIH = VDD –40 IIL Input low current VIL = GND –40 CIN Input capacitance TYP MAX UNIT 1.4 V 0.6 V 40 µA 40 µA 2 pF 6.10 Frequency Tolerance Characteristics (1) VDD = 3.3 V ± 5%, TA = -40°C to 85°C PARAMETER fT (1) Total frequency tolerance TEST CONDITIONS MIN LMK60X2: All output formats, frequency bands and device junction temperature up to 105°C; includes initial freq tolerance, temperature & supply voltage variation, solder reflow and 5-year aging at 40°C LMK60X0: All output formats, frequency bands and device junction temperature up to 105°C; includes initial freq tolerance, temperature & supply voltage variation, solder reflow and 5-year aging at 40°C TYP MAX UNIT –50 50 ppm –25 25 ppm Ensured by characterization. Copyright © 2016–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMK60E2-125M LMK60E2-156M LMK60E0-156M LMK60E0-212M LMK60I2-100M LMK60I2322M 5 LMK60E2-125M, LMK60E2-156M, LMK60E0-156M LMK60E0-212M, LMK60I2-100M, LMK60I2-322M SNAS718B – DECEMBER 2016 – REVISED OCTOBER 2017 www.ti.com 6.11 Power-On/Reset Characteristics (VDD) VDD = 3.3 V ± 5%, TA = -40°C to 85°C PARAMETER TEST CONDITIONS MIN (1) VTHRESH Threshold voltage VDROOP Allowable voltage droop (2) (1) TYP MAX 2.85 UNIT 3 V 0.1 V Time elapsed from VDD at 3.135 V to output enabled 10 ms tSTARTUP Start-up time tOE-EN Output enable time (2) Time elapsed from OE at VIH to output enabled 50 µs tOE-DIS Output disable time (2) Time elapsed from OE at VIL to output disabled 50 µs (1) (2) Ensured by characterization. Ensured by design. 6.12 PSRR Characteristics (1) VDD = 3.3 V, TA = 25°C PARAMETER PSRR (1) (2) (3) Spurs induced by 50-mV power supply ripple (2) (3) at 156.25-MHz output, all output types TEST CONDITIONS MIN TYP Sine wave at 50 kHz –60 Sine wave at 100 kHz –60 Sine wave at 500 kHz –60 Sine wave at 1 MHz –60 MAX UNIT dBc Refer to Parameter Measurement Information for relevant test conditions. Measured max spur level with 50 mVpp sinusoidal signal between 50 kHz and 1 MHz applied on VDD pin DJSPUR (ps, pk-pk) = [2*10(SPUR/20) / (π*fOUT)]*1e6, where PSRR or SPUR in dBc and fOUT in MHz. 6.13 PLL Clock Output Jitter Characteristics (1) (2) VDD = 3.3 V ± 5%, TA = -40°C to 85°C PARAMETER RJ (1) (2) (3) RMS phase jitter (3) (12 kHz – 20 MHz) TEST CONDITIONS fOUT ≥ 100 MHz, all output types MIN TYP MAX UNIT 150 250 fs RMS Refer to Parameter Measurement Information for relevant test conditions. Phase jitter measured with Agilent E5052 signal source analyzer using a differential-to-single ended converter (balun or buffer). Ensured by characterization. 6.14 Additional Reliability and Qualification 6 PARAMETER CONDITION / TEST METHOD Mechanical Shock MIL-STD-202, Method 213 Mechanical Vibration MIL-STD-202, Method 204 Moisture Sensitivity Level J-STD-020, MSL3 Submit Documentation Feedback Copyright © 2016–2017, Texas Instruments Incorporated Product Folder Links: LMK60E2-125M LMK60E2-156M LMK60E0-156M LMK60E0-212M LMK60I2-100M LMK60I2322M LMK60E2-125M, LMK60E2-156M, LMK60E0-156M LMK60E0-212M, LMK60I2-100M, LMK60I2-322M www.ti.com SNAS718B – DECEMBER 2016 – REVISED OCTOBER 2017 7 Parameter Measurement Information 7.1 Device Output Configurations High impedance differential probe LMK60XX LVPECL 150 Oscilloscope 150 Figure 1. LVPECL Output DC Configuration During Device Test High impedance differential probe LMK60XX LVDS Oscilloscope Figure 2. LVDS Output DC Configuration During Device Test High impedance differential probe HCSL LMK60XX 50 Oscilloscope 50 Figure 3. HCSL Output DC Configuration During Device Test LMK60XX Balun/ Buffer LVPECL 150 (1) Phase Noise/ Spectrum Analyzer 150 Figure 4. LVPECL Output AC Configuration During Device Test (1) Also compatible with 85 Ω termination Copyright © 2016–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMK60E2-125M LMK60E2-156M LMK60E0-156M LMK60E0-212M LMK60I2-100M LMK60I2322M 7 LMK60E2-125M, LMK60E2-156M, LMK60E0-156M LMK60E0-212M, LMK60I2-100M, LMK60I2-322M SNAS718B – DECEMBER 2016 – REVISED OCTOBER 2017 www.ti.com Device Output Configurations (continued) LMK60XX Balun/ Buffer LVDS Phase Noise/ Spectrum Analyzer Figure 5. LVDS Output AC Configuration During Device Test LMK60XX Balun/ Buffer HCSL 50 Phase Noise/ Spectrum Analyzer 50 Figure 6. HCSL Output AC Configuration During Device Test Sine wave Modulator Power Supply LMK60XX Balun 150 (LVPECL) Open (LVDS) 50 (HCSL) Phase Noise/ Spectrum Analyzer 150 (LVPECL) Open (LVDS) 50 (HCSL) Figure 7. PSRR Test Setup OUT_P VOD OUT_N 80% VOUT,DIFF,PP = 2 x VOD 0V 20% tR tF Figure 8. Differential Output Voltage and Rise/Fall Time 8 Submit Documentation Feedback Copyright © 2016–2017, Texas Instruments Incorporated Product Folder Links: LMK60E2-125M LMK60E2-156M LMK60E0-156M LMK60E0-212M LMK60I2-100M LMK60I2322M LMK60E2-125M, LMK60E2-156M, LMK60E0-156M LMK60E0-212M, LMK60I2-100M, LMK60I2-322M www.ti.com SNAS718B – DECEMBER 2016 – REVISED OCTOBER 2017 8 Power Supply Recommendations For best electrical performance of LMK60EX, TI recommends using a combination of 10 µF, 1 µF, and 0.1 µF on its power-supply bypass network. TI also recommends using component side mounting of the power-supply bypass capacitors and it is best to use 0201 or 0402 body size capacitors to facilitate signal routing. Keep the connections between the bypass capacitors and the power supply on the device as short as possible. Ground the other side of the capacitor using a low impedance connection to the ground plane. Figure 9 shows the layout recommendation for power supply decoupling of LMK60EX. 9 Layout 9.1 Layout Guidelines The following sections provides recommendations for board layout, solder reflow profile, and power supply bypassing when using LMK60EX to ensure good thermal and electrical performance, along with overall signal integrity of entire system. 9.1.1 Ensuring Thermal Reliability The LMK60EX is a high-performance device. Therefore, pay careful attention to device configuration and the printed-circuit board (PCB) layout with respect to power consumption. The ground pin must be connected to the ground plane of the PCB through three vias or more, as shown in Figure 9, to maximize thermal dissipation out of the package. Equation 1 describes the relationship between the PCB temperature around the LMK60EX and its junction temperature. TB = TJ – ΨJB * P where • • • • TB: PCB temperature around the LMK60EX TJ: Junction temperature of LMK60EX ΨJB: Junction-to-board thermal resistance parameter of LMK60EX (48.7°C/W without airflow) P: On-chip power dissipation of LMK60EX (1) To ensure that the maximum junction temperature of LMK60EX is below 105°C, it can be calculated that the maximum PCB temperature without airflow should be at 87°C or below when the device is optimized for best performance resulting in maximum on-chip power dissipation of 0.36 W. 9.1.2 Best Practices for Signal Integrity For best electrical performance and signal integrity of entire system with LMK60EX, TI recommends routing vias into decoupling capacitors and then into the LMK60EX. TI also recommends increasing the via count and width of the traces wherever possible. These steps ensure lowest impedance and shortest path for high frequency current flow. Figure 9 shows the layout recommendation for LMK60EX. Copyright © 2016–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMK60E2-125M LMK60E2-156M LMK60E0-156M LMK60E0-212M LMK60I2-100M LMK60I2322M 9 LMK60E2-125M, LMK60E2-156M, LMK60E0-156M LMK60E0-212M, LMK60I2-100M, LMK60I2-322M SNAS718B – DECEMBER 2016 – REVISED OCTOBER 2017 www.ti.com Layout Guidelines (continued) Figure 9. LMK60EX Layout Recommendation for Power Supply and Ground 9.1.3 Recommended Solder Reflow Profile TI recommends following the recommendations of the solder paste supplier to optimize flux activity and to achieve proper melting temperatures of the alloy within the guidelines of J-STD-20. Processing the LMK60EX to be processed with the lowest peak temperature possible while also remaining below the components peak temperature rating as listed on the MSL label is preferred. The exact temperature profile would depend on several factors including maximum peak temperature for the component as rated on the MSL label, board thickness, PCB material type, PCB geometries, component locations, sizes, densities within PCB, as well as the recommended soldering profile from the manufacturer and capability of the reflow equipment to as confirmed by the SMT assembly operation. 10 Submit Documentation Feedback Copyright © 2016–2017, Texas Instruments Incorporated Product Folder Links: LMK60E2-125M LMK60E2-156M LMK60E0-156M LMK60E0-212M LMK60I2-100M LMK60I2322M LMK60E2-125M, LMK60E2-156M, LMK60E0-156M LMK60E0-212M, LMK60I2-100M, LMK60I2-322M www.ti.com SNAS718B – DECEMBER 2016 – REVISED OCTOBER 2017 10 Device and Documentation Support 10.1 Receiving Notification of Documentation Updates To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document. 10.2 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 10.3 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. 10.4 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 10.5 Glossary SLYZ022 — TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 11 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. Copyright © 2016–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMK60E2-125M LMK60E2-156M LMK60E0-156M LMK60E0-212M LMK60I2-100M LMK60I2322M 11 LMK60E2-125M, LMK60E2-156M, LMK60E0-156M LMK60E0-212M, LMK60I2-100M, LMK60I2-322M SNAS718B – DECEMBER 2016 – REVISED OCTOBER 2017 www.ti.com PACKAGE OUTLINE SIA0006A QFM - 1.15 mm max height SCALE 2.200 QUAD FLAT MODULE 5.1 4.9 A B PIN 1 INDEX AREA 7.1 6.9 C 1.15 MAX 0.1 C 3X 3.7 6X (0.15) 3 4 4X (0.26) SYMM 2X 5.08 4X 2.54 6X 0.1 0.05 6 1 SYMM 1.43 1.37 6X C A C B 1.03 0.97 4222361/B 10/2015 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. www.ti.com 12 Submit Documentation Feedback Copyright © 2016–2017, Texas Instruments Incorporated Product Folder Links: LMK60E2-125M LMK60E2-156M LMK60E0-156M LMK60E0-212M LMK60I2-100M LMK60I2322M LMK60E2-125M, LMK60E2-156M, LMK60E0-156M LMK60E0-212M, LMK60I2-100M, LMK60I2-322M www.ti.com SNAS718B – DECEMBER 2016 – REVISED OCTOBER 2017 EXAMPLE BOARD LAYOUT SIA0006A QFM - 1.15 mm max height QUAD FLAT MODULE SYMM 6X (1) 1 6 6X (1.4) SYMM 4X (2.54) 4 3 (R0.05) TYP (3.7) LAND PATTERN EXAMPLE 1:1 RATIO WITH PACKAGE SOLDER PADS SCALE:8X 0.07 MIN ALL AROUND METAL SOLDER MASK OPENING SOLDER MASK OPENING METAL UNDER SOLDER MASK SOLDER MASK DEFINED NON SOLDER MASK DEFINED SOLDER MASK DETAILS NOT TO SCALE 4222361/B 10/2015 NOTES: (continued) 3. For more information, see Texas Instruments literature number SLUA271 (www.ti.com/lit/slua271). www.ti.com Copyright © 2016–2017, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMK60E2-125M LMK60E2-156M LMK60E0-156M LMK60E0-212M LMK60I2-100M LMK60I2322M 13 LMK60E2-125M, LMK60E2-156M, LMK60E0-156M LMK60E0-212M, LMK60I2-100M, LMK60I2-322M SNAS718B – DECEMBER 2016 – REVISED OCTOBER 2017 www.ti.com EXAMPLE STENCIL DESIGN SIA0006A QFM - 1.15 mm max height QUAD FLAT MODULE SYMM 12X (1) 1 6 12X (0.6) METAL TYP (R0.05) SYMM 4X (2.54) 4 3 (0.4) TYP (3.7) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL PRINTED SOLDER COVERAGE BY AREA ALL PADS: 86% SCALE:10X 4222361/B 10/2015 NOTES: (continued) 4. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. www.ti.com 14 Submit Documentation Feedback Copyright © 2016–2017, Texas Instruments Incorporated Product Folder Links: LMK60E2-125M LMK60E2-156M LMK60E0-156M LMK60E0-212M LMK60I2-100M LMK60I2322M PACKAGE OPTION ADDENDUM www.ti.com 16-Nov-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LMK60E0-156M25SIAR ACTIVE QFM SIA 6 2500 Green (RoHS & no Sb/Br) NIAU Level-3-260C-168 HR -40 to 85 LMK60E0 156M25 LMK60E0-156M25SIAT ACTIVE QFM SIA 6 250 Green (RoHS & no Sb/Br) NIAU Level-3-260C-168 HR -40 to 85 LMK60E0 156M25 LMK60E0-212M50SIAR ACTIVE QFM SIA 6 2500 Green (RoHS & no Sb/Br) NIAU Level-3-260C-168 HR -40 to 85 LMK60E0 212M50 LMK60E0-212M50SIAT ACTIVE QFM SIA 6 250 Green (RoHS & no Sb/Br) NIAU Level-3-260C-168 HR -40 to 85 LMK60E0 212M50 LMK60E2-125M00SIAR ACTIVE QFM SIA 6 2500 Green (RoHS & no Sb/Br) NIAU Level-3-260C-168 HR -40 to 85 LMK60E2 125M00 LMK60E2-125M00SIAT ACTIVE QFM SIA 6 250 Green (RoHS & no Sb/Br) NIAU Level-3-260C-168 HR -40 to 85 LMK60E2 125M00 LMK60E2-156M25SIAR ACTIVE QFM SIA 6 2500 Green (RoHS & no Sb/Br) Call TI | NIAU Level-3-260C-168 HR -40 to 85 LMK60E2 156M25 LMK60E2-156M25SIAT ACTIVE QFM SIA 6 250 Green (RoHS & no Sb/Br) Call TI | NIAU Level-3-260C-168 HR -40 to 85 LMK60E2 156M25 LMK60I2-100M00SIAR ACTIVE QFM SIA 6 2500 Green (RoHS & no Sb/Br) NIAU Level-3-260C-168 HR -40 to 85 LMK60I2 100M00 LMK60I2-100M00SIAT ACTIVE QFM SIA 6 250 Green (RoHS & no Sb/Br) NIAU Level-3-260C-168 HR -40 to 85 LMK60I2 100M00 LMK60I2-322M26SIAR ACTIVE QFM SIA 6 2500 Green (RoHS & no Sb/Br) NIAU Level-3-260C-168 HR -40 to 85 LMK60I2 322M26 LMK60I2-322M26SIAT ACTIVE QFM SIA 6 250 Green (RoHS & no Sb/Br) NIAU Level-3-260C-168 HR -40 to 85 LMK60I2 322M26 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 16-Nov-2017 Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 16-Nov-2017 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LMK60E0-156M25SIAR QFM SIA 6 2500 330.0 16.4 5.5 7.5 1.5 8.0 16.0 Q1 LMK60E2-125M00SIAR QFM SIA 6 2500 330.0 16.4 5.5 7.5 1.5 8.0 16.0 Q1 LMK60E2-125M00SIAT QFM SIA 6 250 178.0 16.4 5.5 7.5 1.5 8.0 16.0 Q1 LMK60E2-156M25SIAR QFM SIA 6 2500 330.0 16.4 5.5 7.5 1.5 8.0 16.0 Q1 LMK60E2-156M25SIAT QFM SIA 6 250 178.0 16.4 5.5 7.5 1.5 8.0 16.0 Q1 LMK60I2-100M00SIAR QFM SIA 6 2500 330.0 16.4 5.5 7.5 1.5 8.0 16.0 Q1 LMK60I2-100M00SIAT QFM SIA 6 250 178.0 16.4 5.5 7.5 1.5 8.0 16.0 Q1 LMK60I2-322M26SIAR QFM SIA 6 2500 330.0 16.4 5.5 7.5 1.5 8.0 16.0 Q1 LMK60I2-322M26SIAT QFM SIA 6 250 178.0 16.4 5.5 7.5 1.5 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Nov-2017 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LMK60E0-156M25SIAR QFM SIA 6 2500 367.0 367.0 38.0 LMK60E2-125M00SIAR QFM SIA 6 2500 367.0 367.0 38.0 LMK60E2-125M00SIAT QFM SIA 6 250 210.0 185.0 35.0 LMK60E2-156M25SIAR QFM SIA 6 2500 367.0 367.0 38.0 LMK60E2-156M25SIAT QFM SIA 6 250 210.0 185.0 35.0 LMK60I2-100M00SIAR QFM SIA 6 2500 367.0 367.0 38.0 LMK60I2-100M00SIAT QFM SIA 6 250 210.0 185.0 35.0 LMK60I2-322M26SIAR QFM SIA 6 2500 367.0 367.0 38.0 LMK60I2-322M26SIAT QFM SIA 6 250 210.0 185.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2017, Texas Instruments Incorporated