Exar CLC1007 Single, dual, and quad low cost, high speed rro amplifier Datasheet

CLC1007, CLC2007, CLC4007
Single, Dual, and Quad Low Cost,
High Speed RRO Amplifiers
FE ATU R E S
■■ 260MHz bandwidth
■■ Fully specified at +3V, +5V and ±5V
supplies
■■ Output voltage range:
❏❏ 0.03V to 4.95V; V = +5; R = 2kΩ
S
L
■■ Input voltage range:
❏❏ -0.3V to +4.1V; V = +5
S
■■ 220V/μs slew rate
■■ 2.6mA supply current per amplifier
■■ ±100mA linear output current
■■ ±125mA short circuit current
■■ CLC2007 directly replaces LMH6643,
AD8042, AD8052, and AD8092
■■ CLC1007 directly replaces LMH6642,
AD8041, AD8051, and AD8091
General Description
The CLC1007 (single), CLC2007 (dual) and CLC4007(quad) are low cost,
voltage feedback amplifiers. These amplifiers are designed to operate on
+3V to +5V, or ±5V supplies. The input voltage range extends 300mV below
the negative rail and 0.9V below the positive rail.
The CLC1007, CLC2007, and CLC4007 offer superior dynamic
performance with a 260MHz small signal bandwidth and 220V/μs slew
rate. The combination of low power, high output current drive, and rail-torail performance make these amplifiers well suited for battery-powered
communication/computing systems.
The combination of low cost and high performance make the CLC1007,
CLC2007, and CLC4007 suitable for high volume applications in both
consumer and industrial applications such as wireless phones, scanners,
color copiers, and video transmission.
A P P LICATION S
■■ A/D driver
■■ Active filters
■■ CCD imaging systems
■■ CD/DVD ROM
■■ Coaxial cable drivers
■■ High capacitive load driver
■■ Portable/battery-powered applications
■■ Twisted pair driver
■■ Telecom and optical terminals
■■ Video driver
Ordering Information - page 26
Output Voltage Swing vs Competition
Large Signal Frequency Response
6
5
3
CLC2007
Output Amplitude (V)
Normalized Gain (dB)
4
0
Vout = 2Vpp
-3
Vout = 3Vpp
Vout = 4Vpp
-6
3
2
Competition
1
0
-1
-2
-3
-4
Vs = +/- 5V
-9
0.1
RL = 50Ω
VS = ±5V
-5
1
10
100
-6
1000
-5
Frequency (MHz)
© 2007-2014 Exar Corporation -4
-3
-2
-1
0
1
2
3
4
5
Input Amplitude (V)
1 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Absolute Maximum Ratings
Operating Conditions
Stresses beyond the limits listed below may cause
permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect
device reliability and lifetime.
Supply Voltage Range..................................................2.7 to 12.6V
Operating Temperature Range................................-40°C to 125°C
Junction Temperature............................................................ 150°C
Storage Temperature Range....................................-65°C to 150°C
Lead Temperature (Soldering, 10s).......................................260°C
VS.................................................................................. 0V to +14V
VIN............................................................. -VS - 0.5V to +VS +0.5V
Package Thermal Resistance
θJA (TSOT23-5).................................................................215°C/W
θJA (SOIC-8)......................................................................150°C/W
θJA (MSOP-8)................................................................... 200°C/W
θJA (SOIC-14)..................................................................... 90°C/W
θJA (TSSOP-14).................................................................100°C/W
Package thermal resistance (θJA), JEDEC standard, multi-layer
test boards, still air.
ESD Protection
TSOT-5 (HBM)...........................................................................1kV
SOIC-8 (HBM)...........................................................................1kV
TSOT-5 (CDM)...........................................................................2kV
SOIC-8 (CDM)...........................................................................2kV
ESD Rating for HBM (Human Body Model) and CDM (Charged
Device Model).
© 2007-2014 Exar Corporation 2 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Electrical Characteristics at +3V
TA = 25°C, VS = +3V, Rf = 1.5kΩ, RL = 2kΩ to VS/2; G = 2; unless otherwise noted.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Frequency Domain Response
GBWP
-3dB Gain Bandwidth Product
G = +11, VOUT = 0.2Vpp
90
MHz
UGBW
Unity Gain Bandwidth
VOUT = 0.2Vpp, RF = 0
245
MHz
BWSS
-3dB Bandwidth
VOUT = 0.2Vpp
85
MHz
f0.1dB
0.1dB Gain Flatness
VOUT = 0.2Vpp, RL = 150Ω
16
MHz
BWLS
Large Signal Bandwidth
VOUT = 2Vpp
55
MHz
DC-coupled Output
0.03
%
AC-coupled Output
0.04
%
DC-coupled Output
0.03
°
AC-coupled Output
0.06
°
DG
DP
Differential Gain
Differential Phase
Time Domain
tR, tF
Rise and Fall Time
VOUT = 0.2V step; (10% to 90%)
5
ns
tS
Settling Time to 0.1%
VOUT = 1V step
25
ns
OS
Overshoot
VOUT = 0.2V step
8
%
SR
Slew Rate
G = -1, 2V step
175
V/μs
Distortion/Noise Response
THD
Total Harmonic Distortion
1MHz, VOUT = 1Vpp
75
dBc
en
Input Voltage Noise
>50kHz
16
nV/√Hz
XTALK
Crosstalk
f = 5MHz
58
dB
DC Performance
VIO
Input Offset Voltage
dVIO
Average Drift
IB
Input Bias Current
dIB
Average Drift
IOS
Input Offset Current
PSRR
Power Supply Rejection Ratio
AOL
Open Loop Gain
IS
Supply Current
0.5
mV
5
μV/°C
1.4
μA
2
nA/°C
0.05
μA
DC
102
dB
RL = 2kΩ
92
dB
per channel
2.6
mA
Input Characteristics
CIN
Input Capacitance
CMIR
Common Mode Input Range
CMRR
Common Mode Rejection Ratio
0.5
pF
-0.3 to
2.1
V
100
dB
RL = 150Ω
0.3 to
2.75
V
RL = 2kΩ
0.02 to
2.96
V
DC, VCM = 0 to 1.5V
Output Characteristics
VOUT
Output Swing
IOUT
Output Current
ISC
Short Circuit Current
VS
Power Supply Operating Range
VOUT = VS / 2
© 2007-2014 Exar Corporation 3 / 27
±100
mA
±125
V
2.7 to
12.6
V
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Electrical Characteristics at +5V
TA = 25°C, VS = +5V, Rf = 1.5kΩ, RL = 2kΩ to VS/2; G = 2; unless otherwise noted.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Frequency Domain Response
GBWP
-3dB Gain Bandwidth Product
G = +11, VOUT = 0.2Vpp
95
MHz
UGBW
Unity Gain Bandwidth
VOUT = 0.2Vpp, RF = 0
250
MHz
BWSS
-3dB Bandwidth
VOUT = 0.2Vpp
85
MHz
f0.1dB
0.1dB Gain Flatness
VOUT = 0.2Vpp, RL = 150Ω
35
MHz
BWLS
Large Signal Bandwidth
VOUT = 2Vpp
65
MHz
DC-coupled Output
0.03
%
AC-coupled Output
0.04
%
DC-coupled Output
0.03
°
AC-coupled Output
0.06
°
DG
DP
Differential Gain
Differential Phase
Time Domain
tR, tF
Rise and Fall Time
VOUT = 0.2V step
5
ns
tS
Settling Time to 0.1%
VOUT = 2V step
25
ns
OS
Overshoot
VOUT = 0.2V step
5
%
SR
Slew Rate
G = -1, 4V step
220
V/μs
Distortion/Noise Response
THD
Total Harmonic Distortion
1MHz, VOUT = 2Vpp
-75
dBc
en
Input Voltage Noise
>50kHz
16
nV/√Hz
XTALK
Crosstalk
f = 5MHz
58
dB
DC Performance
VIO
Input Offset Voltage
dVIO
Average Drift
-7
IB
Input Bias Current
dIB
Average Drift
IOS
Input Offset Current
PSRR
Power Supply Rejection Ratio
AOL
Open Loop Gain
IS
Supply Current
per channel
0.5
7
5
-2
1.4
2
2
-0.75
0.05
DC
80
102
RL = 2kΩ
80
92
2.6
mV
μV/°C
μA
nA/°C
0.75
μA
dB
dB
4
mA
Input Characteristics
CIN
Input Capacitance
CMIR
Common Mode Input Range
CMRR
Common Mode Rejection Ratio
DC, VCM = 0 to 3.5V
0.5
pF
-0.3 to
4.1
V
75
100
dB
0.35
0.1 to
4.9
Output Characteristics
RL = 150Ω
VOUT
Output Swing
RL = 2kΩ
IOUT
Output Current
ISC
Short Circuit Current
VS
Power Supply Operating Range
VOUT = VS / 2
© 2007-2014 Exar Corporation 4 / 27
4.65
V
0.03 to
4.95
V
±100
mA
±125
V
2.7 to
12.6
V
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Electrical Characteristics at ±5V
TA = 25°C, VS = ±5V, Rf = 1.5kΩ, RL = 2kΩ to GND; G = 2; unless otherwise noted.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Frequency Domain Response
GBWP
-3dB Gain Bandwidth Product
G = +11, VOUT = 0.2Vpp
90
MHz
UGBW
Unity Gain Bandwidth
VOUT = 0.2Vpp, RF = 0
260
MHz
BWSS
-3dB Bandwidth
VOUT = 0.2Vpp
85
MHz
f0.1dB
0.1dB Gain Flatness
VOUT = 0.2Vpp, RL = 150Ω
22
MHz
BWLS
Large Signal Bandwidth
VOUT = 2Vpp
65
MHz
DC-coupled Output
0.03
%
AC-coupled Output
0.04
%
DC-coupled Output
0.03
°
AC-coupled Output
0.06
°
DG
DP
Differential Gain
Differential Phase
Time Domain
tR, tF
Rise and Fall Time
VOUT = 0.2V step
5
ns
tS
Settling Time to 0.1%
VOUT = 2V step, RL = 100Ω
25
ns
OS
Overshoot
VOUT = 0.2V step
5
%
SR
Slew Rate
G = -1, 5V step
225
V/μs
Distortion/Noise Response
THD
Total Harmonic Distortion
1MHz, VOUT = 2Vpp
76
dBc
en
Input Voltage Noise
>50kHz
16
nV/√Hz
XTALK
Crosstalk
f = 5MHz
58
dB
DC Performance
VIO
Input Offset Voltage
dVIO
Average Drift
IB
Input Bias Current
dIB
Average Drift
IOS
Input Offset Current
PSRR
Power Supply Rejection Ratio
AOL
Open Loop Gain
IS
Supply Current
0.5
mV
5
μV/°C
1.3
μA
2
nA/°C
0.04
μA
DC
102
dB
RL = 2kΩ
92
dB
per channel
2.6
mA
Input Characteristics
CIN
Input Capacitance
CMIR
Common Mode Input Range
CMRR
Common Mode Rejection Ratio
0.5
pF
-5.3 to
4.1
V
100
dB
RL = 150Ω
-4.8 to
4.8
V
RL = 2kΩ
-4.95 to
4.93
V
DC, VCM = -5 to 3.5V
Output Characteristics
VOUT
Output Swing
IOUT
Output Current
ISC
Short Circuit Current
VS
Power Supply Operating Range
VOUT = VS / 2
© 2007-2014 Exar Corporation 5 / 27
±100
mA
±125
V
2.7 to
12.6
V
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
CLC1007 Pin Configurations
CLC1007 Pin Assignments
TSOT-5
TSOT-5
OUT
1
-Vs
2
+IN
3
5
+
+Vs
4
-IN
SOIC-8
Pin Name
Description
1
OUT
Output
2
-VS
Negative supply
3
+IN
Positive input
4
-IN
Negative input
5
+VS
Positive supply
SOIC-8
NC
1
-IN
2
+IN
3
-Vs
Pin No.
+
4
8
NC
7
+Vs
6
OUT
5
NC
Pin No.
Pin Name
Description
1
NC
No Connect
2
-IN
Negative input
3
+IN
Positive input
4
-VS
Negative supply
5
NC
No Connect
6
OUT
Output
7
+VS
Positive supply
8
NC
No Connect
CLC2007 Pin Configuration
CLC2007 Pin Assignments
SOIC-8 / MSOP-8
SOIC-8 / MSOP-8
OUT1
1
-IN1
2
+IN1
3
-Vs
4
+
+
Pin Name
1
OUT1
Description
Output, channel 1
+Vs
2
-IN1
Negative input, channel 1
7
OUT2
3
+IN1
Positive input, channel 1
4
-IN2
-VS
6
5
+IN2
Positive input, channel 2
+IN2
6
-IN2
Negative input, channel 2
7
OUT2
8
+VS
8
-
Pin No.
5
© 2007-2014 Exar Corporation 6 / 27
Negative supply
Output, channel 2
Positive supply
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
CLC4007 Pin Configuration
CLC4007 Pin Assignments
SOIC-14 / TSSOP-14
SOIC-14 / TSSOP-14
OUT1
1
14
OUT4
-IN1
2
13
-IN4
+IN1
3
12
+IN4
+VS
4
11
-VS
+IN2
5
10
+IN3
-IN2
6
9
-IN3
OUT2
7
8
OUT3
© 2007-2014 Exar Corporation Pin No.
Pin Name
Description
1
OUT1
2
-IN1
Negative input, channel 1
3
+IN1
Positive input, channel 1
4
+VS
Positive supply
5
+IN2
Positive input, channel 2
6
-IN2
Negative input, channel 2
7
OUT2
Output, channel 2
8
OUT3
Output, channel 3
Output, channel 1
9
-IN3
Negative input, channel 3
10
+IN3
Positive input, channel 3
11
-VS
12
+IN4
Positive input, channel 4
13
-IN4
Negative input, channel 4
14
OUT4
7 / 27
Negative supply
Output, channel 4
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at +3V
TA = 25°C, VS = +3V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted.
Non-Inverting Frequency Response
Inverting Frequency Response
3
3
G = -1
Normalized Gain (dB)
Normalized Gain (dB)
G = +1, RF = 0Ω
0
G = +2
-3
G = +5
G = +10
-6
0
G = -2
-3
G = -5
G = -10
-6
Vs = +3V, VOUT = 0.2Vpp
Vs = +3V, VOUT = 0.2Vpp
-9
-9
0.1
1
10
100
1000
0.1
1
10
Frequency (MHz)
100
1000
Frequency (MHz)
Frequency Response vs CL
Frequency Response vs RL
Vs = +3V, VOUT = 0.2Vpp
CL = 47pF
RS = 20Ω
CL = 100pF
RS = 18Ω
3
CL = 22pF
No RS
0
Normalized Gain (dB)
Normalized Gain (dB)
3
CL = 492pF
RS = 7.5Ω
-3
CL = 1000pF
RS = 4.3Ω
RL = 150Ω
0
RL = 500Ω
-3
-6
-6
-9
-9
RL = 5KΩ
RL = 1KΩ
Vs = +3V, VOUT = 0.2Vpp
0.1
1
10
100
1000
0.1
1
10
Frequency (MHz)
100
1000
Frequency (MHz)
Large Signal Frequency Response
-3dB BW vs Output Voltage
120
3
110
RL = 2KΩ
-3dB Bandwidth (MHz)
Normalized Gain (dB)
100
0
Vout = 1Vpp
-3
Vout = 2Vpp
-6
90
80
RL = 150Ω
70
60
50
40
30
Vs = +3V
-9
0.1
1
10
100
1000
0
Frequency (MHz)
© 2007-2014 Exar Corporation Vs = +3V
20
0.5
1
1.5
2
Output Voltage (Vpp)
8 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at +3V
TA = 25°C, VS = +3V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted.
2nd Harmonic Distortion vs RL over Frequency
55
-20
50
-30
45
-40
Distortion (dBc)
Input Voltage Noise (nV/√Hz)
Input Voltage Noise vs Frequency
40
35
30
Hd2_RL = 2KΩ
-50
-60
Hd2_RL = 150Ω
-70
25
-80
20
-90
15
-100
Vs = +3V_VOUT = 1Vpp
0.1
1
10
100
1000
0
5
10
Frequency (KHz)
15
20
Frequency (MHz)
3rd Harmonic Distortion vs RL over Frequency
2nd Harmonic Distortion vs VO over Frequency
-20
-40
-30
-50
Hd3_RL = 150Ω
-50
-60
Distortion (dBc)
Distortion (dBc)
-40
Hd3_RL = 2KΩ
-70
-60
5MHz
2MHz
-70
1MHz
-80
-80
-90
-90
Vs = +3V_VOUT = 1Vpp
Vs = +3V_RL = 150Ω
-100
-100
0
5
10
15
20
0.5
1
Frequency (MHz)
1.5
2
Output Amplitude (Vpp)
3rd Harmonic Distortion vs VO over Frequency
Non-Inverting Small Signal Pulse Response
1.7
-40
-50
-70
Voltage (V)
Distortion (dBc)
1.6
5MHz
-60
2MHz
1.5
-80
1.4
-90
1MHz
Vs = +3V_RL = 150Ω
Vs = +3V
-100
1.3
0.5
1
1.5
0
2
Output Amplitude (Vpp)
© 2007-2014 Exar Corporation 50
100
150
200
Time (ns)
9 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at +3V
TA = 25°C, VS = +3V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted.
Crosstalk vs Frequency (CLC2007)
3
-40
2.5
-50
2
-60
Crosstalk (dB)
Voltage (V)
Non-Inverting Large Signal Pulse Response
1.5
1
-70
-80
-90
0.5
Vs = +3V, RL = 150Ω, VOUT = 2Vpp
Vs = +3V
-100
0.01
0
0
50
100
150
200
Differential Gain & Phase_DC Coupled
0.1
1
10
Frequency (MHz)
Time (ns)
Differential Gain & Phase_AC Coupled
© 2007-2014 Exar Corporation 10 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at +5V
TA = 25°C, VS = +5V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted.
Non-Inverting Frequency Response
Inverting Frequency Response
3
3
G = -1
Normalized Gain (dB)
Normalized Gain (dB)
G = +1, RF = 0Ω
0
G = +2
-3
G = +5
G = +10
-6
0
G = -2
-3
G = -5
G = -10
-6
Vs = +5V, VOUT = 0.2Vpp
Vs = +5V, VOUT = 0.2Vpp
-9
-9
0.1
1
10
100
1000
0.1
1
10
Frequency (MHz)
100
1000
Frequency (MHz)
Frequency Response vs CL
Frequency Response vs RL
Vs = +5V, VOUT = 0.2Vpp
CL = 47pF
RS = 20Ω
CL = 100pF
RS = 18Ω
3
CL = 22pF
No RS
0
Normalized Gain (dB)
Normalized Gain (dB)
3
CL = 492pF
RS = 7.5Ω
-3
CL = 1000pF
RS = 4.3Ω
RL = 150Ω
0
RL = 500Ω
-3
-6
-6
-9
-9
RL = 5KΩ
RL = 1KΩ
Vs = +5V, VOUT = 0.2Vpp
0.1
1
10
100
1000
0.1
1
10
Frequency (MHz)
100
1000
Frequency (MHz)
Large Signal Frequency Response
-3dB BW vs Output Voltage
110
3
RL = 2KΩ
100
-3dB Bandwidth (MHz)
Normalized Gain (dB)
90
0
Vout = 1Vpp
-3
Vout = 2Vpp
Vout = 3Vpp
-6
80
RL = 150Ω
70
60
50
40
30
Vs = 5V
Vs = +5V
20
-9
0.1
1
10
100
0
1000
© 2007-2014 Exar Corporation 0.5
1
1.5
2
2.5
3
Output Voltage (Vpp)
Frequency (MHz)
11 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at +5V
TA = 25°C, VS = +5V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted.
2nd Harmonic Distortion vs RL over Frequency
55
-20
50
-30
45
-40
Distortion (dBc)
Input Voltage Noise (nV/√Hz)
Input Voltage Noise vs Frequency
40
35
30
Hd2_RL = 2KΩ
-50
-60
Hd2_RL = 150Ω
-70
25
-80
20
-90
15
-100
Vs = +5V_VOUT = 2Vpp
0.1
1
10
100
1000
0
5
10
Frequency (KHz)
3rd Harmonic Distortion vs RL over Frequency
20
2nd Harmonic Distortion vs VO over Frequency
-20
-40
-30
-50
-40
Hd3_RL = 150Ω
Distortion (dBc)
Distortion (dBc)
15
Frequency (MHz)
-50
-60
-70
Hd3_RL = 2kΩ
-60
2MHz
5MHz
-70
-80
1MHz
-80
-90
-90
Vs = +5V_V
+/-5V_V
==2V2V
OUT
OUT
pppp
Vs = +5V_RL = 150Ω
-100
-100
0
5
10
15
20
0.5
1
Frequency (MHz)
1.5
2
Output Amplitude (Vpp)
3rd Harmonic Distortion vs VO over Frequency
Non-Inverting Small Signal Pulse Response
2.7
-40
-50
-70
Voltage (V)
Distortion (dBc)
2.6
5MHz
-60
2MHz
2.5
-80
2.4
-90
1MHz
Vs = +5V_RL = 150Ω
Vs = +5V
2.3
-100
0.5
1
1.5
0
2
© 2007-2014 Exar Corporation 50
100
150
200
Time (ns)
Output Amplitude (Vpp)
12 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at +5V
TA = 25°C, VS = +5V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted.
Non-Inverting Large Signal Pulse Response
Crosstalk vs Frequency (CLC2007)
-40
5
-50
Crosstalk (dB)
Voltage (V)
4
3
2
1
-60
-70
-80
-90
Vs = +5V, RL = 150Ω, VOUT = 2Vpp
Vs = +5V
-100
0.01
0
0
50
100
150
200
Differential Gain & Phase_DC Coupled
0.1
1
10
Frequency (MHz)
Time (ns)
Differential Gain & Phase_AC Coupled
© 2007-2014 Exar Corporation 13 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at ±5V
TA = 25°C, VS = ±5V, RL = 2kΩ to GND, G = +2, RF = 1.5kΩ; unless otherwise noted.
Non-Inverting Frequency Response
Inverting Frequency Response
3
3
G = -1
Normalized Gain (dB)
Normalized Gain (dB)
G = +1, RF = 0Ω
0
G = +2
-3
G = +5
G = +10
0
G = -2
-3
G = -5
G = -10
-6
-6
Vs = +/- 5V, VOUT = 0.2Vpp
Vs = +/- 5V, VOUT = 0.2Vpp
-9
-9
0.1
1
10
100
0.1
1000
1
10
100
1000
Frequency (MHz)
Frequency (MHz)
Frequency Response vs CL
Frequency Response vs RL
Vs = +/- 5V, VOUT = 0.2Vpp
CL = 47pF
RS = 15Ω
CL = 100pF
RS = 15Ω
3
CL = 22pF
No RS
0
Normalized Gain (dB)
Normalized Gain (dB)
3
CL = 492pF
RS = 6.5Ω
-3
CL = 1000pF
RS = 4.3Ω
RL = 150Ω
0
RL = 500Ω
-3
-6
-6
-9
-9
RL = 5KΩ
RL = 1KΩ
Vs = +/-5V, VOUT = 0.2Vpp
0.1
1
10
100
1000
0.1
1
10
Frequency (MHz)
100
1000
Frequency (MHz)
Large Signal Frequency Response
-3dB BW vs Output Voltage
110
3
100
RL = 2KΩ
-3dB Bandwidth (MHz)
Normalized Gain (dB)
90
0
Vout = 2Vpp
-3
Vout = 3Vpp
Vout = 4Vpp
-6
80
RL = 150Ω
70
60
50
40
30
Vs = +/- 5V
-9
Vs = +/-5V
20
0.1
1
10
100
1000
0
Frequency (MHz)
© 2007-2014 Exar Corporation 0.5
1
1.5
2
2.5
3
3.5
4
Output Voltage (Vpp)
14 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at ±5V
TA = 25°C, VS = ±5V, RL = 2kΩ to GND, G = +2, RF = 1.5kΩ; unless otherwise noted.
2nd Harmonic Distortion vs RL over Frequency
55
-20
50
-30
45
-40
Distortion (dBc)
Input Voltage Noise (nV/√Hz)
Input Voltage Noise vs Frequency
40
35
30
Hd2_RL = 2KΩ
-50
-60
Hd2_RL = 150Ω
-70
25
-80
20
-90
15
-100
Vs = +/-5V_VOUT = 2Vpp
0.1
1
10
100
1000
0
5
10
Frequency (KHz)
3rd Harmonic Distortion vs RL over Frequency
20
2nd Harmonic Distortion vs VO over Frequency
-20
-40
-30
-50
-40
Hd3_RL = 150Ω
Distortion (dBc)
Distortion (dBc)
15
Frequency (MHz)
-50
-60
-70
Hd3_RL = 2kΩ
-60
5MHz
2MHz
-70
-80
-80
1MHz
-90
-90
Vs = +/-5V_VOUT = 2Vpp
Vs = +/-5V_RL = 150Ω
-100
-100
0
5
10
15
20
0.5
1
Frequency (MHz)
1.5
2
Output Amplitude (Vpp)
3rd Harmonic Distortion vs VO over Frequency
Non-Inverting Small Signal Pulse Response
-40
0.25
0.2
0.15
0.1
-60
5MHz
-70
Voltage (V)
Distortion (dBc)
-50
2MHz
-80
0.05
0
-0.05
-0.1
-0.15
-90
1MHz
-0.2
Vs = +/-5V_RL = 150Ω
-100
Vs = +/-5V
-0.25
0.5
1
1.5
2
0
Output Amplitude (Vpp)
© 2007-2014 Exar Corporation 50
100
150
200
Time (ns)
15 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at ±5V
TA = 25°C, VS = ±5V, RL = 2kΩ to GND, G = +2, RF = 1.5kΩ; unless otherwise noted.
Crosstalk vs Frequency (CLC2007)
3
-40
2
-50
1
-60
Crosstalk (dB)
Voltage (V)
Non-Inverting Large Signal Pulse Response
0
-1
-70
-80
-90
-2
Vs = +/- 5V, RL = 150Ω, VOUT = 2Vpp
Vs = +/-5V
-100
0.01
-3
0
50
100
150
200
Differential Gain & Phase_DC Coupled
0.1
1
10
Frequency (MHz)
Time (ns)
Differential Gain & Phase_AC Coupled
© 2007-2014 Exar Corporation 16 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Application Information
+Vs
General Description
The CLC1007, CLC2007, and CLC4007 are single supply,
general purpose, voltage-feedback amplifiers fabricated on
a complementary bipolar process using a patent pending
topography. They feature a rail-to-rail output stage and is
unity gain stable. Both gain bandwidth and slew rate are
insensitive to temperature.
Input
0.1μF
+
Output
RL
0.1μF
The common mode input range extends to 300mV below
ground and to 0.9V below Vs. Exceeding these values will
not cause phase reversal. However, if the input voltage
exceeds the rails by more than 0.5V, the input ESD devices
will begin to conduct. The output will stay at the rail during
this overdrive condition.
6.8μF
G=1
-Vs
Figure 3: Unity Gain Circuit
+Vs
The design is short circuit protected and offers “soft”
saturation protection that improves recovery time.
6.8μF
+
Figures 1, 2, and 3 illustrate typical circuit configurations for
non-inverting, inverting, and unity gain topologies for dual
supply applications. They show the recommended bypass
capacitor values and overall closed loop gain equations. Figure
4 shows the typical non-inverting gain circuit for single supply
applications.
+Vs
6.8μF
In
0.1μF
+
Out
-
Rf
Rg
6.8μF
Figure 4: Single Supply Non-Inverting Gain Circuit
Input
0.1μF
+
Output
RL
0.1μF
Rg
6.8μF
-Vs
Rf
G = 1 + (Rf/Rg)
Figure 1: Typical Non-Inverting Gain Circuit
+Vs
Overdrive Recovery
For an amplifier, an overdrive condition occurs when the
output and/or input ranges are exceeded. The recovery time
varies based on whether the input or output is overdriven
and by how much the ranges are exceeded. The CLC1007,
CLC2007, and CLC4007 will typically recover in less than
20ns from an overdrive condition. Figure 5 shows the
CLC2007 in an overdriven condition.
6
6.8μF
OUTPUT
4
Input
Rg
0.1μF
+
2
Voltage (V)
R1
Output
RL
0.1μF
0
INPUT
-2
Rf
-4
6.8μF
-Vs
Vs = +/-5V_RL=2K_AV=+5
G = - (Rf/Rg)
-6
0
For optimum input offset
voltage set R1 = Rf || Rg
200
300
400
500
600
700
800
900
1,000
Time (ns)
Figure 2: Typical Inverting Gain Circuit
© 2007-2014 Exar Corporation 100
Figure 5: Overdrive Recovery
17 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Power Dissipation
Power dissipation should not be a factor when operating
under the stated 2kΩ load condition. However, applications
with low impedance, DC coupled loads should be analyzed
to ensure that maximum allowed junction temperature is
not exceeded. Guidelines listed below can be used to verify
that the particular application will not cause the device to
operate beyond it’s intended operating range.
Assuming the load is referenced in the middle of the power
rails or Vsupply/2.
The CLC1007 is short circuit protected. However, this may
not guarantee that the maximum junction temperature
(+150°C) is not exceeded under all conditions. Figure 6
shows the maximum safe power dissipation in the package
vs. the ambient temperature for the packages available.
2.5
Maximum Power Dissipation (W)
Maximum power levels are set by the absolute maximum
junction rating of 170°C. To calculate the junction
temperature, the package thermal resistance value ThetaJA
(θJA) is used along with the total die power dissipation.
TJunction = TAmbient + (θJA × PD)
Where TAmbient is the temperature of the working
environment.
In order to determine PD, the power dissipated in the load
needs to be subtracted from the total power delivered by the
supplies.
TSSOP-14
2
SOIC-14
1.5
SOIC-8
1
0.5
TSOT-5
MSOP-8
0
-40
-20
0
20
40
60
80
100
120
Ambient Temperature (°C)
PD = Psupply - Pload
Figure 6. Maximum Power Derating
Supply power is calculated by the standard power equation.
Psupply = Vsupply × IRMSsupply
Vsupply = VS+ - VSPower delivered to a purely resistive load is:
Pload = ((Vload)RMS2)/Rloadeff
The effective load resistor (Rloadeff) will need to include the
effect of the feedback network. For instance,
Driving Capacitive Loads
Increased phase delay at the output due to capacitive loading
can cause ringing, peaking in the frequency response, and
possible unstable behavior. Use a series resistance, RS,
between the amplifier and the load to help improve stability
and settling performance. Refer to Figure 7.
Rloadeff in Figure 3 would be calculated as:
Input
+
RL || (Rf + Rg)
-
These measurements are basic and are relatively easy to
perform with standard lab equipment. For design purposes
however, prior knowledge of actual signal levels and load
impedance is needed to determine the dissipated power.
Here, PD can be found from
PD = PQuiescent + PDynamic - Pload
Quiescent power can be derived from the specified IS values
along with known supply voltage, Vsupply. Load power can
be calculated as above with the desired signal amplitudes
using:
Rf
Output
CL
RL
Rg
Figure 7. Addition of RS for Driving Capacitive Loads
Table 1 provides the recommended RS for various capacitive
loads. The recommended RS values result in approximately
<1dB peaking in the frequency response.
CL (pF)
(Vload)RMS = Vpeak / √2
( Iload)RMS = ( Vload)RMS / Rloadeff
The dynamic power is focused primarily within the output
stage driving the load. This value can be calculated as:
PDynamic = (VS+ - Vload)RMS × ( Iload)RMS
© 2007-2014 Exar Corporation Rs
RS (Ω)
-3dB BW (MHz)
22pF
0
118
47pF
15
112
100pF
15
91
492pF
6.5
59
Table 1: Recommended RS vs. CL
18 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
For a given load capacitance, adjust RS to optimize the
tradeoff between settling time and bandwidth. In general,
reducing RS will increase bandwidth at the expense of
additional overshoot and ringing.
Layout Considerations
General layout and supply bypassing play major roles in
high frequency performance. Exar has evaluation boards to
use as a guide for high frequency layout and as an aid in
device testing and characterization. Follow the steps below
as a basis for high frequency layout:
■■
Include 6.8µF and 0.1µF ceramic capacitors for power supply
decoupling
■■
Place the 6.8µF capacitor within 0.75 inches of the power pin
■■
Place the 0.1µF capacitor within 0.1 inches of the power pin
■■
■■
Remove the ground plane under and around the part,
especially near the input and output pins to reduce parasitic
capacitance
Minimize all trace lengths to reduce series inductances
Refer to the evaluation board layouts below for more
information.
Figure 8. CEB002 & CEB003 Schematic
Evaluation Board Information
The following evaluation boards are available to aid in the
testing and layout of these devices:
Evaluation Board #
Products
CEB002
CLC1007 in TSOT
CEB003
CLC1007 in SOIC
CEB006
CLC2007 in SOIC
CEB010
CLC2007 in MSOP
CEB018
CLC4007 in SOIC
CEB019
CLC4007 in TSSOP
Evaluation Board Schematics
Figure 9. CEB002 Top View
Evaluation board schematics and layouts are shown in
Figures 8-20. These evaluation boards are built for dualsupply operation. Follow these steps to use the board in a
single-supply application:
1. Short -VS to ground.
2. Use C3 and C4, if the -VS pin of the amplifier is not
directly connected to the ground plane.
© 2007-2014 Exar Corporation 19 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Figure 10. CEB002 Bottom View
Figure 13. CEB006 & CEB010 Schematic
Figure 11. CEB003 Top View
Figure 14. CEB006 Top View
Figure 12. CEB003 Bottom View
© 2007-2014 Exar Corporation 20 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Figure 15. CEB006 Bottom View
Figure 18. CEB018 Schematic
Figure 16. CEB010 Top View
Figure 19. CEB018 Top View
Figure 17. CEB010 Bottom View
© 2007-2014 Exar Corporation 21 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Figure 20. CEB018 Bottom View
© 2007-2014 Exar Corporation 22 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Mechanical Dimensions
TSOT-5 Package
MSOP-8 Package
© 2007-2014 Exar Corporation 23 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
SOIC-8 Package
SOIC-14 Package
© 2007-2014 Exar Corporation 24 / 27
exar.com/CLC1007
Rev 1D
ECN 1344-13 11/01/2013
CLC1007, CLC2007, CLC4007
TSSOP-14 Package
ECN 1347-07 11/19/2013
© 2007-2014 Exar Corporation 25 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Ordering Information
Part Number
Package
Green
Operating Temperature Range
Packaging
CLC1007IST5X
TSOT-5
Yes
-40°C to +125°C
Tape & Reel
CLC1007IST5MTR
TSOT-5
Yes
-40°C to +125°C
Mini Tape & Reel
CLC1007IST5EVB
Evaluation Board
N/A
N/A
N/A
CLC1007ISO8X
SOIC-8
Yes
-40°C to +125°C
Tape & Reel
CLC1007ISO8MTR
SOIC-8
Yes
-40°C to +125°C
Mini Tape & Reel
CLC1007ISO8EVB
Evaluation Board
N/A
N/A
N/A
CLC2007ISO8X
SOIC-8
Yes
-40°C to +125°C
Tape & Reel
CLC2007ISO8MTR
SOIC-8
Yes
-40°C to +125°C
Mini Tape & Reel
CLC2007ISO8EVB
Evaluation Board
N/A
N/A
N/A
CLC2007IMP8X
MSOP-8
Yes
-40°C to +125°C
Tape & Reel
CLC2007IMP8MTR
MSOP-8
Yes
-40°C to +125°C
Mini Tape & Reel
CLC2007IMP8EVB
Evaluation Board
N/A
N/A
N/A
CLC4007ITP14X
TSSOP-14
Yes
-40°C to +125°C
Tape & Reel
CLC4007ITP14MTR
TSSOP-14
Yes
-40°C to +125°C
Mini Tape & Reel
CLC4007ITP14EVB
Evaluation Board
N/A
N/A
N/A
CLC4007ISO14X
SOIC-14
Yes
-40°C to +125°C
Tape & Reel
CLC4007ISO14MTR
SOIC-14
Yes
-40°C to +125°C
Mini Tape & Reel
CLC4007ISO14EVB
Evaluation Board
N/A
N/A
N/A
CLC1007 Ordering Information
CLC2007 Ordering Information
CLC4007 Ordering Information
Moisture sensitivity level for all parts is MSL-1.
© 2007-2014 Exar Corporation 26 / 27
exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Revision History
Revision
1D (ECN 1451-07)
Date
December
2014
Description
Reformat into Exar data sheet template. Updated ordering information table to include MTR and EVB
part numbers. Increased “I” temperature range from +85 to +125°C. Removed “A” temp grade parts,
since “I” is now equivalent. Updated thermal resistance numbers and package outline drawings.
For Further Assistance:
Email: [email protected] or [email protected]
Exar Technical Documentation: http://www.exar.com/techdoc/
Exar Corporation Headquarters and Sales Offices
48760 Kato Road
Tel.: +1 (510) 668-7000
Fremont, CA 94538 - USA
Fax: +1 (510) 668-7001
NOTICE
EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation
assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free
of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user’s specific application. While the information
in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies.
EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected
to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation
receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR
Corporation is adequately protected under the circumstances.
Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
© 2007-2014 Exar Corporation 27 / 27
exar.com/CLC1007
Rev 1D
Similar pages