AD AD96687BP Ultrafast comparator Datasheet

a
FEATURES
Fast: 2.5 ns Propagation Delay
Low Power: 118 mW per Comparator
Packages: DIP, SOIC, PLCC
Power Supplies: +5 V, –5.2 V
Logic Compatibility: ECL
50 ps Delay Dispersion
APPLICATIONS
High Speed Triggers
High Speed Line Receivers
Threshold Detectors
Window Comparators
Peak Detectors
Ultrafast Comparators
AD96685/AD96687
AD96685 FUNCTIONAL BLOCK DIAGRAM
NONINVERTING
INPUT
INVERTING
INPUT
Q OUTPUT
Q OUTPUT
RL
LATCH
ENABLE
RL
VT
AD96687 FUNCTIONAL BLOCK DIAGRAM
NONINVERTING
INPUT
INVERTING
INPUT
LE
RL
Q OUTPUT
Q OUTPUT
Q OUTPUT
Q OUTPUT
RL
RL
LE
LATCH
ENABLE
NONINVERTING
INPUT
INVERTING
INPUT
RL
LE
VT
LE
LATCH
ENABLE
THE OUTPUTS ARE OPEN EMITTERS, REQUIRING EXTERNAL
PULL-DOWN RESISTORS. THESE RESISTORS MAY BE IN THE
RANGE OF 50⍀-200⍀ CONNECTED TO –2.0V, OR 200⍀-2000⍀
GENERAL DESCRIPTION
The AD96685 and AD96687 are ultrafast voltage comparators.
The AD96685 is a single comparator with 2.5 ns propagation
delay; the AD96687 is an equally fast dual comparator. Both
devices feature 50 ps propagation delay dispersion which is a
particularly important characteristic of high-speed comparators.
It is a measure of the difference in propagation delay under
differing overdrive conditions.
A fast, high precision differential input stage permits consistent
propagation delay with a wide variety of signals in the commonmode range from –2.5 V to +5 V. Outputs are complementary
digital signals fully compatible with ECL 10 K and 10 KH logic
families. The outputs provide sufficient drive current to directly
drive transmission lines terminated in 50 Ω to –2 V. A level
sensitive latch input which permits tracking, track-hold, or
sample-hold modes of operation is included.
The AD96685 is available in industrial –25°C to +85°C range
in 16-pin SOIC.
The AD96687 is available in industrial range –25°C to +85°C,
in 16-pin DIP, SOIC, and 20-lead PLCC.
REV. D
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2001
AD96685/AD96687–SPECIFICATIONS
ELECTRICAL CHARACTERISTICS (Positive Supply Voltage = 5.0 V; Negative Supply Voltage = –5.2 V, unless otherwise noted.)
Industrial Temperature Range –25ⴗC to +85ⴗC
Temp
Test
Level
25°C
Full
Full
25°C
Full
25°C
Full
25°C
25°C
Full
Full
I
VI
V
I
VI
I
VI
V
V
VI
VI
ENABLE INPUT
Logic “1” Voltage
Logic “0” Voltage
Logic “1” Current
Logic “0” Current
Full
Full
Full
Full
VI
VI
VI
VI
–1.1
DIGITAL OUTPUTS3
Logic “1” Voltage
Logic “0” Voltage
Full
Full
VI
VI
–1.1
25°C
25°C
25°C
25°C
25°C
IV
IV
IV
IV
V
2.5
2.5
2.5
2.5
50
3.5
3.5
3.5
3.5
2.5
2.5
2.5
2.5
50
3.5
3.5
3.5
3.5
ns
ns
ns
ns
ps
25°C
25°C
25°C
IV
IV
IV
2.0
0.5
0.5
3.0
1.0
1.0
2.0
0.5
0.5
3.0
1.0
1.0
ns
ns
ns
Full
Full
Full
VI
VI
VI
8
15
70
9
18
15
31
70
18
36
mA
mA
dB
Parameter
INPUT CHARACTERISTICS
Input Offset Voltage
Input Offset Drift
Input Bias Current
Input Offset Current
Input Resistance
Input Capacitance
Input Voltage Ranges2
Common-Mode Rejection Ratio
SWITCHING PERFORMANCES
Propagation Delays4
Input to Output HIGH
Input to Output LOW
Latch Enable to Output HIGH
Latch Enable to Output LOW
Dispersions5
Latch Enable
Minimum Pulsewidth
Minimum Setup Time
Minimum Hold Time
POWER SUPPLY6
Positive Supply Current (+5.0 V)
Negative Supply Current (–5.2 V)
Power Supply Rejection Ratio7
Min
AD96685BR
Typ
Max
1
20
7
0.1
AD96687BQ/BP/BR
Min
Typ
Max
2
3
1
20
7
10
13
1.0
1.2
0.1
200
2
–2.5
80
2
3
10
13
1.0
1.2
200
2
+5.0
90
–2.5
80
+5.0
90
–1.1
–1.5
40
5
60
60
mV
mV
µV/°C
µA
µA
µA
µA
kΩ
pF
V
dB
–1.5
40
5
V
V
µA
µA
–1.5
V
V
–1.1
–1.5
Unit
NOTES
1
RS = 100 Ω.
2
Input Voltage Range can be extended to –3.3 V if –VS = –6.0 V.
3
Outputs terminated through 50 Ω to –2.0 V.
4
Propagation delays measured with 100 mV pulse (10 mV overdrive) to 50% transition point of the output.
5
Change in propagation delay from 100 mV to 1 V input overdrive.
6
Supply voltages should remain stable within ± 5% for normal operation.
7
Measured at ± 5% of +VS and –VS.
Specifications subject to change without notice.
LATCH
ENABLE
COMPARE
50%
tS
LATCH
tH
DIFFERENTIAL
INPUT
VOLTAGE
Q
VDD
tPW(E)
VIN
VOS
tPD
tPD(E)
tS
– Minimum Setup Time
tH
– Minimum Hold Time
tPD
– Input to Output Delay
tPD(E) – LATCH ENABLE to Output Delay
tPW(E) – Minimum LATCH ENABLE Pulsewidth
50%
50%
Q
VOS
– Input Offset Voltage
VOD
– Overdrive Voltage
Figure 1. System Timing Diagram
–2–
REV. D
AD96685/AD96687
ABSOLUTE MAXIMUM RATINGS 1
EXPLANATION OF TEST LEVELS
Positive Supply Voltage (+VS) . . . . . . . . . . . . . . . . . . . . . 6.5 V
Negative Supply Voltage (–VS) . . . . . . . . . . . . . . . . . . . –6.5 V
Input Voltage Range2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 5 V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Latch Enable Voltage . . . . . . . . . . . . . . . . . . . . . . . . –VS to 0 V
Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA
Operating Temperature Range3
AD96685BR/AD96687BQ/BR/BP . . . . . . . –25°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –55°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 175°C
Lead Soldering Temperature (10 sec) . . . . . . . . . . . . . . 300°C
Test Level
I – 100% production tested.
II – 100% production tested at 25°C, and sample tested at
specified temperatures.
III – Sample tested only.
IV – Parameter is guaranteed by design and characterization
testing.
V – Parameter is a typical value only.
VI – All devices are 100% production tested at 25°C; 100%
production tested at temperature extremes for extended
temperature devices; sample tested at temperature extremes for commercial/industrial devices.
NOTES
1
Absolute maximum ratings are limiting values, may be applied individually, and
beyond which serviceability of the circuit may be impaired. Functional operation
under any of these conditions is not necessarily implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
2
Under no circumstances should the input voltages exceed the supply voltages.
3
Typical thermal impedances . . .
AD96685 SOIC
qJA = 170°C/W; qJC = 60°C/W
AD96687 Ceramic
qJA = 115°C/W; qJC = 57°C/W
AD96687 SOIC
qJA = 92°C/W; qJC = 47°C/W
AD96687 PLCC
qJA = 81°C/W; qJC = 45°C/W
FUNCTIONAL DESCRIPTION
Pin Name
Description
+VS
NONINVERTING INPUT
Positive supply terminal, nominally 5.0 V.
Noninverting analog input of the differential input stage. The NONINVERTING INPUT must be
driven in conjunction with the INVERTING INPUT.
Inverting analog input of the differential input stage. The INVERTING INPUT must be driven in
conjunction with the NONINVERTING INPUT.
In the “compare” mode (logic HIGH), the output will track changes at the input of the comparator. In the “latch” mode (logic LOW), the output will reflect the input state just prior to the
comparator being placed in the “latch” mode. LATCH ENABLE must be driven in conjunction
with LATCH ENABLE for the AD96687.
In the “compare” mode (logic LOW), the output will track changes at the input of the comparator.
In the “latch” mode (logic HIGH), the output will reflect the input state just prior to the comparator
being placed in the “latch” mode. LATCH ENABLE must be driven in conjunction with
LATCH ENABLE for the AD96687.
Negative supply terminal, nominally –5.2 V.
One of two complementary outputs. Q will be at logic HIGH if the analog voltage at the
NONINVERTING INPUT is greater than the analog voltage at the INVERTING INPUT (provided the comparator is in the “compare” mode). See LATCH ENABLE and LATCH ENABLE
(AD96687 only) for additional information.
One of two complementary outputs. Q will be at logic LOW if the analog voltage at the
NONINVERTING INPUT is greater than the analog voltage at the INVERTING INPUT
(provided the comparator is in the “compare” mode). See LATCH ENABLE and LATCH ENABLE
(AD96687 only) for additional information.
One of two grounds, but primarily associated with the digital ground. Both grounds should be
connected together near the comparator.
One of two grounds, but primarily associated with the analog ground. Both grounds should be
connected together near the comparator.
INVERTING INPUT
LATCH ENABLE
LATCH ENABLE
–VS
Q
Q
GROUND 1
GROUND 2
REV. D
–3–
AD96685/AD96687
PIN CONFIGURATIONS
3
14 NC
4
AD96685
13 NC
TOP VIEW
5 (Not to Scale) 12 Q OUTPUT
LATCH ENABLE 6
NC 7
VS– 8
11 Q OUTPUT
10 NC
9
NC
NC = NO CONNECT
GROUND
LATCH
ENABLE
NC
LATCH
ENABLE
VS–
Q OUTPUT
15 NC
Q OUTPUT
16 GROUND 2
2
Q OUTPUT 1
NC
VS+
NONINVERTING
INPUT
INVERTING
INPUT
NC
AD96687BQ/BR
Q OUTPUT
GROUND 1 1
AD96687BP
Q OUTPUT
AD96685BR
3
2
1
20
19
3
18
4
17
5
AD96687
6
TOP VIEW
(Not to Scale)
7
15
14
8
9
10
11
12
Q OUTPUT
15 Q OUTPUT
GROUND
LATCH ENABLE
4
LATCH ENABLE
5 (Not to Scale) 12 LATCH ENABLE
14 GROUND
AD96687
13 LATCH ENABLE
TOP VIEW
VS– 6
INVERTING INPUT 7
NONINVERTING 8
INPUT
11 VS+
10 INVERTING INPUT
9
NONINVERTING
INPUT
13
INVERTING
INPUT
NONINVERTING
INPUT
NC
NONINVERTING
INPUT
INVERTING
INPUT
NC = NO CONNECT
16
GROUND
LATCH
ENABLE
NC
LATCH
ENABLE
VS+
16 Q OUTPUT
2
ORDERING GUIDE
Model
Type
Temperature
Range
Description
Package
Options
AD96685BR
AD96687BP
AD96687BQ
AD96687BR
AD96687BR-REEL
Single
Dual
Dual
Dual
Dual
–25°C to +85°C
–25°C to +85°C
–25°C to +85°C
–25°C to +85°C
–25°C to +85°C
16-Pin SOIC, Industrial
20-Pin PLCC, Industrial
16-Pin DIP, Industrial
16-Pin SOIC, Industrial
16-Pin SOIC, Industrial
R-16A
P-20A
Q-16
R-16A
R-16A
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD96685/AD96687 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
–4–
WARNING!
ESD SENSITIVE DEVICE
REV. D
Typical Performance Characteristics–AD96685/AD96687
APPLICATIONS INFORMATION
The AD96685/AD96687 comparators are very high speed devices.
Consequently, high speed design techniques must be employed
to achieve the best performance. The most critical aspect of any
AD96685/AD96687 design is the use of a low impedance
ground plane.
Another area of particular importance is power supply decoupling.
Normally, both power supply connections should be separately
decoupled to ground through 0.1 µF ceramic and 0.001 µF mica
capacitors. The basic design of comparator circuits makes the
negative supply somewhat more sensitive to variations. As a
result, more attention should be placed on ensuring a “clean”
negative supply.
The LATCH ENABLE input is active LOW (latched). If the
latching function is not used, the LATCH ENABLE input should
be grounded (ground is an ECL logic HIGH). The LATCH
ENABLE input of the AD96687 should be tied to –2.0 V or left
“floating,” to disable the latching function. An alternate use of
the LATCH ENABLE input is as a hysteresis control input. By
varying the voltage at the LATCH ENABLE input for the
AD96685 and the differential voltage between both latch
inputs for the AD96687, small variations in the hysteresis can
be achieved.
REV. D
Occasionally, one of the two comparator stages within the
AD96687 will not be used. The inputs of the unused comparator
should not be allowed to “float.” The high internal gain may
cause the output to oscillate (possibly affecting the other comparator which is being used) unless the output is forced into a
fixed state. This is easily accomplished by ensuring that the two
inputs are at least one diode drop apart, while also grounding
the LATCH ENABLE input.
The best performance will be achieved with the use of proper
ECL terminations. The open-emitter outputs of the AD96685/
AD96687 are designed to be terminated through 50 Ω resistors to –2.0 V, or any other equivalent ECL termination. If high
speed ECL signals must be routed more than a few centimeters,
MicroStrip or StripLine techniques may be required to ensure
proper transition times and prevent output ringing.
The AD96685/AD96687 have been specifically designed to
reduce propagation delay dispersion over an input overdrive
range of 100 mV to 1 V. Propagation delay dispersion is the
change in propagation delay which results from a change in
the degree of overdrive (how far the switching point is exceeded
by the input). The overall result is a higher degree of timing
accuracy since the AD96685/AD96687 are far less sensitive
to input variations than most comparator designs.
–5–
AD96685/AD96687
Typical Applications
+VREF
AD96685/
AD96687
50⍀
VIN
AD96685/
AD96687
VIN
OUTPUTS
VREF
50⍀
50⍀
50⍀
50⍀
50⍀
50⍀
–VREF
LATCH ENABLE
INPUT
OUTPUT
50⍀
50⍀
50⍀
50⍀
–2V
–2V
Figure 2. High Speed Sampling Circuit
Figure 3. High Speed Window Comparator
–6–
REV. D
AD96685/AD96687
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
16-Lead Ceramic DIP
0.005 (0.13) MIN
16-Lead SOIC
0.098 (2.49) MAX
16
9
PIN 1
1
8
0.840 (21.34) MAX
0.200 (5.08)
MAX
0.394 (10.00)
0.385 (9.78)
0.310 (7.87)
0.220 (5.59)
0.158 (4.00)
0.150 (3.80)
0.320 (8.13)
0.290 (7.37)
0.060 (1.52)
0.015 (0.38)
0.150
(3.81)
0.200 (5.08)
MIN
0.125 (3.18)
SEATING
0.023 (0.58) 0.100 0.070 (1.78)
PLANE
0.014 (0.36) (2.54) 0.030 (0.76)
BSC
PIN 1
0.015 (0.38)
0.008 (0.20)
15°
0°
0.310 (7.87)
0.220 (5.58)
16
9
1
8
0.050 (1.27)
BSC
0.010 (0.25)
0.004 (0.10)
0.244 (6.20)
0.228 (5.80)
0.069 (1.75)
0.053 (1.35)
0.018 (0.46)
0.014 (0.36)
0.205 (5.20)
0.181 (4.60)
SEATING 0.015 (0.38)
PLANE
0.007 (0.18)
8ⴗ
0ⴗ 0.045 (1.15)
0.025 (0.50)
20-Lead PLCC
0.173 (4.39)
0.165 (4.19)
0.045 (1.14)
0.042 (1.07)
0.045 (1.14)
0.042 (1.07)
3
0.020 (0.51) MIN
0.035 (0.890)
R 0.034 (0.864)
19
PIN 1
IDENTIFIER
4
18
TOP VIEW
(PINS DOWN)
14
8
0.020
(0.50)
MAX
0.050
(1.27)
BSC
9
0.017 (0.432)
0.013 (0.330)
0.330 (8.38)
0.029 (0.737) 0.290 (7.37)
0.026 (0.660)
13
0.353 (8.97)
0.350 (8.89) SQ
0.390 (9.91)
SQ
0.385 (9.78)
0.025 (0.64) MIN
0.060 (1.53) MIN
Revision History
Location
Page
Data Sheet changed from REV. C to REV. D.
Edits to FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Edits to GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Edits to ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Edits to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Edits to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Deleted DIE LAYOUT AND MECHANICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Edits to OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
REV. D
–7–
–8–
PRINTED IN U.S.A.
C00698–0–2/02(D)