MIC2788/MIC2789 Push-Button Reset IC General Description Features The MIC2788/MIC2789 are low-current, ultra-small, pushbutton reset supervisors with long set-up delays. The devices feature two manual reset inputs and two reset outputs. The devices initiate a reset for the reset timeout period when the /MR0 and /MR1 inputs are asserted low for a period longer than the set-up delay. The two manual reset inputs and long set-up period help to avoid unintended system resets. Both manual reset inputs can be tied together if a single push-button reset is desired. The MIC2788 features integrated pull-up resistors on the /MR0 and /MR1 inputs, while the MIC2789 requires external pull-up resistors. The PDY input pin selects between a 2s, 4s or 6s set-up period. Factory-programmed reset timeout periods of 140ms (min.) and 240ms (min.) are available. An active-low, open-drain reset output (/RST) and an active-high, push-pull reset output (RSTP) provide flexibility when interfacing to various microcontrollers, PMICs, or load switches. The MIC2788/MIC2789 consume a quiescent current of only 2.9µA and are offered in a tiny, space-saving 8-pin ® thin MLF (2mm x 2mm x 0.55mm) package. Data sheets and support documentation can be found on Micrel’s web site at: www.micrel.com. • 1.6V to 5.5V operating voltage • 2.9µA supply current when /MR0, /MR1 are not asserted • Asserting /MR0 and /MR1 for longer than set-up delay asserts reset output for the reset timeout period • Programmable delay (PDY) input selects 2.0s, 4.0s or 6.0s set-up delay • Factory-programmed 140ms (min.) or 240ms (min.) reset timeout period • Integrated /MR0, /MR1 pull-up resistors (MIC2788) • Dual Reset Outputs: − Open-drain active-low reset (/RST) output − Push-pull active-high reset (RSTP) output • −40°C to 85°C ambient operating temperature range • 8-pin 2mm x 2mm x 0.55mm thin MLF® package Applications • • • • • Smart phones MP3 players Portable navigation devices Set-top boxes (STBs) Tablets/pads _________________________________________________________________________________________________________________________ Typical Application MLF and MicroLeadFrame are registered trademarks of Amkor Technologies, Inc. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com October 2011 M9999-102711-A Micrel, Inc. MIC2788/MIC2789 Ordering Information (1) Part Number MIC2788-XYMT MIC2788-YYMT (2) MIC2789-XYMT MIC2789-YYMT (2) Marking Minimum tRESET (ms) 8XA 140 8-Pin (2mm × 2mm) Thin MLF® Yes 8YA 240 ® 8-Pin (2mm × 2mm) Thin MLF Yes 9XA 140 8-Pin (2mm × 2mm) Thin MLF® No 240 ® No 9YA Package (3,4) Integrated Pull-Up Resistors 8-Pin (2mm × 2mm) Thin MLF Notes: 1. All devices available in Tape and Reel only. 2. Contact factory for availability. 3. Thin MLF ® ▲ = Pin 1 identifier. Thin MLF ® is a Green RoHS compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free. 4. Pin Configuration MIC2788/89 ® 8-Pin (2mm × 2mm) Thin MLF Top View Pin Description Pin Number Pin Name 1 RSTP 2 GND Supply Ground. 3 /MR1 Active-Low Manual Reset Input. The MIC2788 has an internal 65kΩ pull-up resistor to VIN while the MIC2789 requires an external pull-up resistor to VIN if used with a push-button. Pull this pin low to assert and force a reset. Pulling both manual reset inputs low for the setup delay time causes one reset output pulse for the reset timeout delay period. Connect to VIN if unused, do not leave floating. 4 /RST Active-Low Open Drain Reset Output. This output changes from high to low when both manual reset pins are pulled low for the setup delay period. /RST remains low for the reset timeout delay after the setup delay has elapsed and it requires an external pull-up resistor. 5 PDY Programmable Delay Input with Tri-State Connection. When left open, set-up delay is 2s, when connected to GND, set-up delay is 4s and when connected to VIN, set-up delay is 6s. October 2011 Pin Function Active-High Push-Pull Reset Output. This output changes from low-to-high when both manual reset pins are pulled low for the setup delay period. RSTP remains high for the reset timeout delay duration after the setup delay period has elapsed. 2 M9999-102711-A Micrel, Inc. MIC2788/MIC2789 Pin Description (Continued) Pin Number Pin Name 6 NC 7 /MR0 8 VIN EPAD EPAD October 2011 Pin Function No Connect. Leave pin floating. Active-Low Manual Reset Input. The MIC2788 has an internal 65kΩ pull-up resistor to VIN while the MIC2789 requires an external pull-up resistor to VIN if used with a push-button. Pull this pin low to assert and force a reset. Pulling both manual reset inputs low for the setup delay time causes one reset output pulse for the reset timeout delay period. If unused, connect to VIN; do not leave floating. Positive Supply Voltage. A minimum 0.1μF decoupling ceramic capacitor must be connected between VIN and GND close to the pins. Exposed Pad. Connect to GND. 3 M9999-102711-A Micrel, Inc. MIC2788/MIC2789 Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VIN) ..................................... −0.3V to +6.0V Reset Input Voltage (/MR0, /MR1)........ −0.3V to VIN + 0.3V Open Drain Reset Output (/RST) ................. −0.3V to +6.0V Push-Pull Reset Output (RSTP)............ −0.3V to VIN + 0.3V Tri-State Programmable Delay (PDY)... −0.3V to VIN + 0.3V Lead Temperature (soldering, 10sec.)....................... 260°C Junction Temperature (TJ) ........................−40°C to +150°C Storage Temperature (Ts)......................... −55°C to +150°C ESD Rating (Human Body Model)(3) .............................. 2kV ESD Rating (Machine Model)(3) ....................................300V Supply Voltage (VIN)..................................... +1.6V to +5.5V Reset Input Voltage (/MR0, /MR1)......................... 0V to VIN Open Drain Reset Output (/RST)...................... 0V to +5.5V Push-Pull Reset Output (/RSTP) ........................... 0V to VIN Tri-State Programmable Delay (PDY).................... 0V to VIN Ambient Temperature (TA) .......................... –40°C to +85°C Junction Thermal Resistance 2mm × 2mm Thin MLF® (θJA).............................90°C/W Electrical Characteristics(4) VIN = 3.0V, TA = 25°C, Bold values indicate –40°C ≤ TA ≤ +85°C; unless noted otherwise. Parameter Conditions Min. Typ. Max. Units 5.5 V Power Supply Input Supply Voltage (VIN) Supply Current (IIN) 1.6 VIN = 5V; /MR0, /MR1, /RST, RSTP, and PDY open 3.4 VIN = 3V; /MR0, /MR1, /RST, RSTP, and PDY open 2.9 7.5 µA Reset Time Set-Up Delay (tSETUP) Reset Timeout Delay (tRESET) PDY = Open 1.6 2.0 2.4 PDY = 0V 3.2 4.0 4.8 PDY = VIN 4.8 6.0 7.2 Option X 140 220 280 Option Y 240 350 480 s ms Reset Outputs (/RST, RSTP) Reset Output Voltage Low (/RST Output and RSTP Output) (VOL) Reset Output Voltage High (RSTP Output) (VOH) /RST Output Leakage (ILO) VIN = 4.5V, ISINK = 3.2mA 0.3 VIN = 3.3V, ISINK = 2.5mA 0.3 VIN = 1.6V, ISINK = 1.0mA 0.3 VIN = 4.5V, ISOURCE = 0.8mA 0.8 × VIN VIN = 2.7V, ISOURCE = 0.5mA 0.8 × VIN VIN = 1.6V, ISOURCE = 250μA 0.8 × VIN V/RST = 5.5V V V 0.3 μA Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5kΩ in series with 100pF. 4. Specification for packaged product only. October 2011 4 M9999-102711-A Micrel, Inc. MIC2788/MIC2789 Electrical Characteristics (4) (Continued) VIN = 3.0V, TA = 25°C, Bold values indicate –40°C ≤ TA ≤ +85°C; unless noted otherwise. Parameter Conditions Min. Typ. Max. Units Manual Reset Inputs (/MR0, /MR1) Input High Voltage (VIH) V 1.2 Input Low Voltage (VIL) 0.3 Internal Pull-Up Resistor (RPU) MIC2788 only 65 Leakage Current /MR0, /MR1 pin (IMR) /MR0, /MR1 inputs; MIC2789 only −1.0 V kΩ 1.0 μA Programmable Setup Delay Input (PDY) Input Bias Current PDY Pin (IPDY) October 2011 PDY = VIN, /MR0 = /MR1 = 0V +60 μA PDY = VIN, /MR0 = VIN or /MR1= VIN 100 nA PDY = 0V, /MR0 = /MR1 = 0V -60 μA PDY = 0V, /MR0 = VIN or /MR1 = VIN 100 nA 5 M9999-102711-A Micrel, Inc. MIC2788/MIC2789 Typical Characteristics 3.0 DUAL RESET DELAY (s) VIN = 3.0V PDY = OPEN 3.4 2.8 2.2 1.6 1.0 2.5 2.0 1.5 10 35 60 -15 10 35 60 DUAL RESET DELAY (s) 2.8 2.2 1.6 1.0 60 85 4.5 4.0 3.5 10 35 60 PDY = VIN PDY = VIN 1.0 35 TEMPERATURE (°C) October 2011 -40 -15 60 85 10 35 60 85 TEMPERATURE (°C) Reset Timeout Delay (Option X) vs. Temperature (PDY = VIN) 6.5 6.0 5.5 5.0 10 210 250 VIN = 3.0V -15 220 85 7.0 1.6 -40 230 200 -15 V IN = 3.0V 2.2 85 240 Setup Delay vs. Temperature (PDY = VIN) 2.8 60 VIN = 3.0V PDY = 0V TEMPERATURE (°C) DUAL RESET DELAY (s) 3.4 35 250 -40 VIN Supply Current vs. Temperature (PDY = VIN) 10 Reset Timeout Delay (Option X) vs. Temperature (PDY = 0V) VIN = 3.0V PDY = 0V TEMPERATURE (°C) 4.0 -15 TEMPERATURE (°C) RESET TIMEOUT DELAY(ms) 35 210 -40 3.0 10 220 85 5.0 3.4 -15 230 Setup Delay vs. Temperature (PDY = 0V) VIN = 3.0V PDY = 0V -40 240 TEMPERATURE (°C) VIN Supply Current vs. Temperature (PDY = 0V) 4.0 VIN = 3.0V PDY = OPEN 200 -40 85 RESET TIMEOUT DELAY (ms) -15 TEMPERATURE (°C) SUPPLY CURRENT (µA) 250 VIN = 3.0V PDY = OPEN 1.0 -40 SUPPLY CURRENT (µA) Reset Timeout Delay (Option X) vs. Temperature (PDY = OPEN) RESET TIMEOUT DELAY (ms) 4.0 SUPPLY CURRENT (µA) Setup Delay vs. Temperature (PDY = OPEN) VIN Supply Current vs. Temperature (PDY = OPEN) VIN = 3.0V PDY = VIN 240 230 220 210 200 -40 -15 10 35 TEMPERATURE (°C) 6 60 85 -40 -15 10 35 60 85 TEMPERATURE (°C) M9999-102711-A Micrel, Inc. MIC2788/MIC2789 Typical Characteristics (Continued) Setup Delay vs. Input Voltage VIN Supply Current vs. Input Voltage 4.3 3.6 2.9 2.2 1.5 250 RESET TIMEOUT DELAY (ms) 10.0 /MR0 = NOT ASSERTED /MR1 = NOT ASSERTED DUAL RESET DELAY (s) SUPPLY CURRENT (µA) 5.0 Reset Timeout Delay (Option X) vs. Input Voltage 8.0 PDY =VIN 6.0 PDY = 0V 4.0 PDY =OPEN 2.0 0.0 0 1 2 3 4 INPUT VOLTAGE (V) October 2011 5 6 240 230 220 210 200 0 1 2 3 4 INPUT VOLTAGE (V) 7 5 6 0 1 2 3 4 5 6 INPUT VOLTAGE (V) M9999-102711-A Micrel, Inc. MIC2788/MIC2789 Timing Diagram October 2011 8 M9999-102711-A Micrel, Inc. MIC2788/MIC2789 Functional Diagram October 2011 9 M9999-102711-A Micrel, Inc. MIC2788/MIC2789 to tie this resistor to some other voltage, other than VIN, thus enabling level-shifting of the /RST output. The pullup voltage must be limited to 5.5V or less to avoid damage to the MIC2788/MIC2789. The pull-up resistor must be small enough to supply current to the inputs and leakage paths that are driven by the /RST output. A recommended value is 100kΩ. Leave floating if the /RST pin is unused. The RSTP pin is a push-pull output that is driven to VIN. It cannot be level-shifted to another voltage. It is an inverted signal of /RST. Application Information Design and Product Advantages The dual reset programmability of the MIC2788/ MIC2789 allows for already existing manual push buttons to be used to generate a hardware reset based on pre-programmed timing requirements. This ability to increase the functionality of already existing buttons, allows for cost reduction and more robust phone designs. The dual reset delay time allows for significant protection against accidental resets due to its long time duration and dual push button requirement. The fixed reset timeout delay allows for more predictable phone operation during hardware resets. The tri-state option provides an easy to use way to select between three reset delay time options with no additional external components required. Supply Bypass Capacitor A 0.1µF input bypass capacitor must be placed from VIN (Pin 8) to GND (Pin 2). Programmable Delay Pin (PDY) The MIC2788/MIC2789 has a programmable dual reset delay time, tSETUP, that is set via a tri-state logic configuration. The PDY pin is intended to be connected to the VIN supply voltage, ground or left floating. PDY Configuration tSETUP OPEN 2s GND 4s VIN 6s Figure 1. MIC2788/MIC2789 Used in Multiple Supply System The reset outputs /RST and RSTP are asserted when the dual reset delay time, tSETUP, is exceeded while the /MR0, /MR1 pins are driven low. Both the reset outputs remain asserted for a factory-programmed reset timeout delay time tRESET. Two options are available with 140ms or 240ms minimum tRESET duration. The /RST pin is driven active low while the RSTP pin is driven active high for the tRESET duration. The reset outputs are deasserted for VIN < 1.6V. Dual Manual Reset Inputs (/MR0, /MR1) The /MR0, /MR1 input pins have integrated pull-up resistors for the MIC2788 but require external pull-up resistors for the MIC2789. A recommended value is 100kΩ to keep the current consumption low when the push-button switches are pressed. The behavior of the reset outputs is independent of the order in which the /MR0, /MR1 inputs are driven low. If both inputs are low for a setup delay time, only one reset pulse, of width tRESET, is generated. Keeping both inputs low for a longer time does not generate additional reset output pulses. Reset Outputs (/RST and RSTP) The /RST output is a simple open-drain N-channel MOSFET structure that requires a pull-up resistor. For most applications, the pull-up voltage will be the same as the power supply that supplies VIN to the MIC2788/MIC2789. As shown in Figure 1, it is possible October 2011 Figure 2. Manual Reset Function 10 M9999-102711-A Micrel, Inc. MIC2788/MIC2789 Typical Applications Figure 3. MIC2788/89 Used for Interrupting System Power Figure 4. MIC2788/89 Used for Microcontroller Reset October 2011 11 M9999-102711-A Micrel, Inc. MIC2788/MIC2789 Evaluation Board Schematic Bill of Materials Item Part Number C1 GRM188R71C104KA01D R1, R2, R4 CRCW0603100KJNEA U1 MIC2788-XYMT MIC2789-XYMT Manufacturer Murata(1) (2) Vishay Micrel, Inc.(3) Description Qty. 0.1µF, 16V capacitor, X7R, 0603 1 100k, 5% resistor, 0603 3 Push-Button Supervisor Reset ICs 1 Notes: 1. Murata Tel: www.murata.com. 2. Vishay Tel: www.vishay.com. 3. Micrel, Inc.: www.micrel.com. October 2011 12 M9999-102711-A Micrel, Inc. MIC2788/MIC2789 PCB Layout Recommendations Top Layer Top Silkscreen October 2011 13 M9999-102711-A Micrel, Inc. MIC2788/MIC2789 PCB Layout Recommendations (Continued) Copper Layer Bottom Silkscreen October 2011 14 M9999-102711-A Micrel, Inc. MIC2788/MIC2789 Package Information 8-Pin 2mm × 2mm Thin MLF® October 2011 15 M9999-102711-A Micrel, Inc. MIC2788/MIC2789 Recommended Landing Pattern 8-Pin 2mm × 2mm Thin MLF® October 2011 16 M9999-102711-A Micrel, Inc. MIC2788/MIC2789 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2011 Micrel, Incorporated. October 2011 17 M9999-102711-A