CURRENT 6.0 Amperes VOLTAGE 50 to 1000 Volts FR601 THRU FR607 Features · Fast switching · Low leakage · Low forward voltage drop · High current capability · High current surge · High reliability P-6 0.360(9.1) 0.340(8.6) DIA. 1.0(25.4) MIN. 0.360(9.1) 0.340(8.6) Mechanical Data · Case : P-6 molded plastic body · Terminals : Plated axial lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.074 ounce, 2.08 gram 1.0(25.4) MIN. 0.052(1.3) 0.048(1.2) DIA. Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols FR 601 FR 602 FR 603 FR 604 FR 605 FR 606 FR 607 Units Maximum recurrent peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current 0.375"(9.5mm) lead length TA=75℃ I(AV) 6.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 300 Amps VF 1.3 Volts Maximum instantaneous forward voltage at 6.0A Maximum DC reverse current at rated DC blocking voltage Maximum full load reverse current full cycle average. 0.375"(9.5mm) lead length at TL=55℃ 10 μA IR 150 Maximum reverse recovery time (Note 1) Trr Typical junction capacitance (Note 2) CJ 150 pF TJ TSTG -65 to +150 ℃ Operating junction and storage temperature range Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. 150 250 500 ns RATINGS AND CHARACTERISTIC CURVES FR601 THRU FR607 FIG.2-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 8 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 6 PEAK FORWARD SURGE CURRENT(AMPERES) AVERAGE FORWARD CURRENT(A) FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE 4 2 0 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE ( ℃) 600 8.3m SINGLE HALF SINE WAVE (JEDEC Method) 500 400 300 200 100 0 1 5 FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 50 100 NUMBER OF CYCLES AT 60Hz FIG.4-TYPICAL JUNCTION CAPACITANCE 1000 500 200 100 100 JUNCTION CAPACITANCE(pF) INSTANTANEOUS FORWARD CURRENT(AMPERES) 10 40 10 1 TJ=25℃ 60 40 TJ=25℃ 20 10 6 4 Pulse Width=300mS 2 1% Duty Cycle 1 0.1 0.2 0 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0.4 1 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) FIG.5-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50W NON INDUCTIVE 10W NON INDUCTIVE +0.5A (+) 25Vdc (APPROX) ( D.U.T. PULSE GENERATOR (NOTE2) Trr 0 -0.25A ) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE1) NOTES: 1.Rise Time=7ns max. input impedance=1 megohm 22pF 2.Rise Time=10ns max. source impedance =50 ohms 2 4 REVERSE VOLTAGE. (V) -1.0A 1cm SET TIME BASE FOR 50/100 ns/cm 10 20 40 100