MC4 Series High Voltage 4-Resistor SMD DIP Package Ohmite’s MC4 Series offers 4 high voltage SMD resistors in a single DIP package, supplied on tape and reel for automated placement. Each resistor provides a rating of 0.75W with a maximum voltage of 2500 VDC. Designers can specify up to 4 different resistor value/ tolerance combinations and connect then individually, in series, or parallel to derive countless results. The flexible S-Bend terminals provide solder joint integrity while leaving space between the resistor pack and the PCB. Standard parts are available in single resistance values for immediate delivery. F e at u r e s • Unique terminals allow spacing between board and resistor • Design allows multiple configurations • 2,500 volts max. per resistor per pack; 10KV total • Supplied on tape & reel for automated placement S ER I E S S PE C I F I C AT I ON S Series MC4 Resistance Range (Ohms) 200Ω to 5,000M Power @25°C per resistor 0.75W Max. Operating Voltage 2,500 c h a r a c t e r is t ics Standard Temperature Coefficient 50PPM/°C 100PPM/°C 200Ω-250M 251M-5,000M p e r f o r m a n c e d ata Characteristic Test Method Resistor Thick film on Alumina Humidity MIL-STD-202, Method 103B, Condition B Resistance Range 200 ohms to 5,000M Power Rating 0.75W per resistor, 3.0W total Voltage Rating 2500 VDC per resistor Tolerance 5% to 20% Specification Dielectric Withstanding MIL-STD-202, Method 301, Voltage 750V Insulation Resistance MIL-STD-202, Method 302, Condition A or B Operating -55°C to +180°C Temperature Thermal Shock MIL-STD-202, Method 107G, Condition B, B-1, or F TCR and VCR see Slim Mox Solder Silver solder is recommended for MC4 resistors. Leaching of the silver in the termination will occur if non-silver solder is used. 60/40 tinlead solders are not recommended for use with the MC4 product. Load Life MIL-STD-202, Method 108A, Condition D Resistance to Solvents MIL-STD-202, Method 215G 26 3 in parallel 2.25W 2500 VDC 1 individual 0.75W 2500 VDC >10,000M or greater dry ±0.20% ±1.0% No degradation of coating or marking ±0.25% Vibration, High MIL-STD-202, Method 204D, Frequency Condition D ±.020% ±0.50% P o ssi b l e c o n f i g u r a t i o n s 2 pairs in parallel 1.5W each 2500 VDC each ±0.25% Shock (Specified Pulse) MIL-STD-202, Method 213B, Condition I Power Conditioning MIL-R-49462A, Par 4.8 4 individual 0.75W each 2500 VDC each ±0.25% 4 in series 3W 10,000 VDC 2 in series 1.5W 5000 VDC 2 in parallel 1.5W 2500 VDC 3 in series 2.25W 7500 VDC 1 individual 0.75W 2500 VDC 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • [email protected] 2 pairs in series 1.5W each 5000 VDC each 4 in parallel 3W 2500 VDC MC4 Series High Voltage 4-Resistor SMD DIP Package d im e n si o n s (in./mm) Land Pattern 0.750" max. (19.05mm) 0.71" ±.01 (18.03mm) 0.740" (18.8mm) R1 0.190" typ. (4.8mm) 0.110" (2.8mm) R2 0.75" ±.01 (19.05mm) 0.650" (16.5mm) 0.080" (2.0mm) R3 R4 0.03" (0.76mm) 0.080" (2.0mm) 0.580" (14.7mm) 0.676" (17.17mm) o r d e r i n g i n f o r m at i o n Tape and Reel E = RoHS optional compliant 250 per reel M C 4 - 1 0 0 2 F E R MC4 Series Ohms First 3 digits are significant; 4th digit is multiplier (# of zeroes to follow). Examples: 1003 = 100KΩ 5004 = 5MΩ 1007 = 1GΩ Tolerance J = 5% K = 10% P = 20% Standard Part Numbers Part Tape and Reel Orientation Description MC4-1003JER 100K ohms per resistor, 5% MC4-5003JER 500K ohms per resistor, 5% MC4-1004JER 1M ohms per resistor, 5% MC4-5004JER 5M ohms per resistor, 5% MC4-1005JER 10M ohms per resistor, 5% MC4-5005JER 50M ohms per resistor, 5% MC4-1006JER 100M ohms per resistor, 5% MC4-5006JER 500M ohms per resistor, 5% MC4-1007KER 1G ohms per resistor, 10% MC4-5007KER 5G ohms per resistor, 10% *Custom part numbers are assigned sequentially. MC4-SP0001, MC4-SP0002, etc. Go to this link to design your own MC4 resistor and have a unique part number assigned. www. ohmite.com/mc4sp/ Design online at: www.ohmite.com/mc4sp/ 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • [email protected] 27