RF SOLUTIONS FQ1216ME (MK3 family) Multi-Standard Desktop Video Modules Product specification 3139 149 10330 1 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 FEATURES • • • • • • • • • • • • Multi-Standard TV Systems Broadcast reception True 5 V device (low power dissipation) Full frequency range from channel E2 (48.25 MHz) to channel E69 (855.25 MHz) PLL controlled tuning Programmable PLL step size (31.25 / 50 kHz or 62.5 kHz) True-synchronous vision IF demodulator (PLL) Ultra linear FM PLL demodulator Demodulated video output, AF sound output, second IF sound output. 2 I C-bus control of tuning, address selection, AFC status information nd User-settable 2 IF address for PIP application Complies with European regulations on radiation, signal handling and immunity (“CENELEC 55020, 55013” ) Small horizontally mounted metal 70 mm housing ORDERING INFORMATION TYPE DESCRIPTION nd ORDER NUMBERS FQ1216ME/I H-3 IEC / Horizontal / User-settable 2 FQ1216MP/I H-3 IEC / Horizontal User-settable 2 IF address IF address nd nd FQ1216ME/I V-3 IEC / Vertical / 2 FQ1216ME/P H-3 Phono / Horizontal / User-settable 2 IF address FQ1216ME/L H-3 fixed IF address 3139 147 18291 3139 147 18321 3139 147 19151 nd nd Long IEC / Horizontal / User-settable 2 IF address 3139 147 18771 3139 147 18891 MARKING The following items of information are printed on a sticker that is on the top cover of the tuner: • • • • • Type number Code number Origin letter of factory Change code Year and week code 3139 149 10330 2 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 DESCRIPTION The FQ1216ME family belongs to the new FM1200 MK3 family of small size frontends, which are designed to meet a wide range of RF applications in the PC /TV Multi-Media environment. The FQ1216ME combines the functions of an all-band TV tuner, and a multi-standard TV IF demodulation unit for both positive and negative modulated TV systems. The FQ1216ME is intended for CCIR L/L’ (France), B/G, I and D/K systems. The FQ1216MP covers only CCIR B/G, D/K and I. 2 The frontends have a built-in digital (I C) PLL tuning system. A DC-DC converter circuit is built-in in the FQ1216ME to synthesize the tuning voltage required, thus making the frontend a true 5V device. The FQ1216ME/IV-3 has a fixed address of # 84 for the IF processor. For all others, a second address can be set by using a 2K2 resistor at 10 of the module. All modules use the narrowband AGC detection system. INTERMEDIATE FREQUENCIES SYSTEM L L’ B/G D/K I Picture carrier 38.90 33.95 38.90 38.90 38.90 Colour 34.47 38.38 34.47 34.47 34.47 Sound 1 32.40 40.40 33.40 32.40 32.90 Sound 2 - - 33.16 - - NICAM 33.05 39.80 33.05 33.05 32.348 CHANNEL COVERAGE BAND FREQUENCY (MHz) Low band 48.25 to 158.00 MHz Mid band 160.00 to 442.00 MHz + High band 442.00 to 863.25 MHz + Can cover down to 45.75 MHz (Ch A for Ireland) 3139 149 10330 3 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 PINNING SYMBOL PIN DESCRIPTION N.C. 1 (AGC Monitor) Do Not Connect * N.C. 2 (Tuning Voltage Monitor) Do Not Connect * +5V 3 Supply Voltage Vb, Tuner section SCL 4 I²C-Serial Clock SDA 5 I²C-Serial Data AS_TU 6 I²C-Address Select_Tuner part (see Pg 20) - x Not Connected - x Not Connected NC 9 Not Connected IF-AS 10 Second Address for IF circuit * see Pg 20) 2 IF sound 11 Second IF sound output CVBS 12 Composite Video Baseband Signal +5V, IF 13 Supply Voltage, IF section AF O/P 14 AF sound output nd GROUND Mounting Tags (TH1,TH2,TH3,TH4) * For process use only 3139 149 10330 4 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 LIMITING VALUES Limiting values under operational conditions The tuners are guaranteed to function properly under the following conditions. SYMBOL VAGC VT VS PARAMETER AGC Voltage Monitor (not to be connected) (See Note 1) Tuning Voltage Monitor (not to be connected) Supply Voltage Vb Ripple susceptibility (see Note 2) 20Hz 1kHz 1kHz 200kHz Supply current PIN 1 MIN. 10 M TYP. MAX. UNIT Ω 2 - - - - 3 4.75 5 5.25 V 80 2 10 150 mVpp mVpp mA VSCL SCL bus input voltage 4 -0.3 5.25 V VSDA SDA Bus input voltage SDA Bus current (open collector) 5 -0.3 -1.0 5.25 5 V mA AS voltage (see Note 3) 6 5.25 V nd 2 IF sound output - Load impedanceD.C. 11 1.0 1.0 kΩ kΩ 12 75 75 100 Ω Ω ns 5.25 V 2 10 160 mVpp mVpp mA A.C. Composite Video Baseband Signal - Load impedanceD.C. (see 10.3) (modulus) A.C. - Load time constant 13 Supply voltage, IF section 4.75 Ripple susceptibility (see Note 2) 20Hz 1kHz Current - 1kHz 500kHz 100 AF output - Load impedance 14 D.C. A.C. 100.0 10.0 kΩ kΩ Note 1 : Minimum impedance required is 10MΩ, otherwise AGC voltage is loaded down. For process only. Note 2 : Maximum allowable Ripple voltage superimposed on the +5V supply in the frequency range from 20 Hz to 500 kHz. Criteria : for TV : ∆f<2.12 kHz or AM < 0.28% Note 3 : For detailed information about address coding, refer to Application Information. 3139 149 10330 5 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 Environmental conditions SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT -25 +85 °C - 100 % Non-operational Conditions TAMB Ambient temperature RH Relative humidity gB Bump acceleration 25 g - 245 m/s gS Shock acceleration 50 g - 490 m/s Vibration amplitude (10-55 Hz) - 0.35 mm 2 2 Operational conditions TAMB Ambient temperature 0 +60 °C RH Relative humidity - 95 % OVERALL PERFORMANCE Conditional data Unless otherwise specified, all electrical values for “Overall performance” apply at the following conditions. SYMBOL PARAMETER VALUE UNIT TAMB ambient temperature 25 ± 5 o RH relative humidity 60 ± 15 % VS supply voltage (tuner and IF section) 5 ± 0.125 V aerial source impedance (unbalanced) 75 Ω second IF sound output load 0.5 kΩ Video output load 75 Ω AF1 sound output load 100 kΩ ZS(AE) ZIF VST 3139 149 10330 6 C Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 TUNER CHARACTERISTICS EQUIPMENT PARAMETER VALUE UNIT DC Voltmeter input impedance 10 MΩ Oscilloscope input impedance resistance 1 MΩ capacitance 15 pF Spectrum analyzer input impedance 50 Ω FET probe input impedance resistance 10 MΩ capacitance 3.5 pF 3139 149 10330 7 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 TEST DIAGRAM The frontend characteristics are measured according to the test diagram depicted below : aerial connector TV 7 8 1 2 3 4 5 6 9 10 11 12 13 14 1 nF SCL SDA 3 kΩ 33 µF + 10 nF + 5V FM1200 MK3 Evaluation board BU4 BU5 P BU6 Video out (1) SA (1) BU4 loaded with 75 Ω (video monitor) DA SA = Spectrum Analyzer P = FET probe DA = Distortion Analyzer (Zi - 100 k Ω) The minimum load impedance required at the CVBS output75 Ω (both AC and DC) 3139 149 10330 8 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 Definitions of test signals TEST SIGNAL FREQ. AMPLITUDE MODULATION (MHz) A0: unmodulated vision carrier A1: L-system signal with video modulation A2: B/G/D/K/I -system signal with video modulation A3: L' - system signal with video modulation. B1: unmodulated main sound carrier B/G/I/D/K system as chosen B2: AM-modulated sound carrier L-system B3: FM-modulated main sound carrier B/G/I/D/K system respectively B4: unmodulated 2nd sound carrier B/G – system B5: unmodulated main sound carrier L system B6: AM modulated sound carrier L' system 3139 149 10330 480.25 60 dB(µV) 480.25 60 dB(µV) (peak white) 480.25 60 dB(µV) (top sync.) 55.75 60 dB(µV) (peak white) A2 + 5.5/6.0/6.5 MHz 486.75 MHz -13 dB respectively wrt A2 -10 dB with respect to test signals A0 or A1 A2 + 5.5/6.0/6.5 MHz -13 dB respectively wrt A2 A2 + 5.85 MHz -20 dB respectively wrt A2 A1 + 6.5 MHz A3 - 6.5 MHz -10 dB wrt test signal A1 -10 dB wrt test signal A3 9 100 % (sync. level at 0%), 2T-pulse and bar, unless otherwise indicated. 100% (rest carrier 10%), 2T-pulse and bar, unless otherwise indicated 100% (sync. white < 6%), 2T pulse and bar, unless otherwise indicated m=0.54, mod. freq. 1 kHz, unless otherwise indicated freq.dev.=27 kHz, mod.freq. 1kHz, 50 µs pre-emphasis, unless otherwise indicated M = 0.54, mod. freq. 1 kHz, unless otherwise indicated Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 AERIAL INPUT CHARACTERISTICS SYMBOL PARAMETER CONDITIONS referred to 75 Ω at RF picture carrier frequency VSWR VSURGE VANT surge protection MIN. MAX. - 5 5 antenna terminal disturbance voltage up to 1.75 GHz UNIT kV - 46 dBµV TYP. MAX. UNIT 158.00 442.00 863.25 MHz MHz MHz 55 55 55 MHz MHz dB dB dB GENERAL CHARACTERISTICS SYMBOL PARAMETER fb ∆fb voltage gain αj frequency range low band mid band high band margin low band mid/high band low band mid band high band Image rejection low band mid band αIF high band IF rejection All bands tlj Oscillators lock-in time VESD ESD protection at the terminals Maximum signal handling 3139 149 10330 CONDITIONS MIN. 48.25 160.00 442.00 1.5 1.5 36 36 36 - wanted test signal Fant at 60 dBuV - unwanted test signal at (Fant + 77.7) MHz - wanted test signal Fant. - unwanted test signal A0 with frequency (FIF,PC - 1) MHz Tuning speed (lock bit, CP = 1) All terminals of each frontend are protected against electrostatic discharge up to The products are classified in category B (MIL-STD883C). Fwanted 65 dB 60 dB 50 dB 60 dB 150 ms KV 2 100 10 45 45 45 110 - dBµV Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 Video and audio characteristics PARAMETER TEST SIGNAL TEST MIN. TYP. MAX. UNIT 0.7 1.0 1.3 Vpp POINT CVBS output level Amplitude video signal DC level of sync. Pulse CVBS amplitude at discrete frequencies 2 MHz 3 MHz 4.43 MHz Sound Carriers Rejection Specification valid for : B/G, I and D/K mode wrt 1 MHz for : 5.5/6.0 MHz 6.5 MHz Unweighted CVBS Signal to Noise Ratio Specification valid for : L/L’, B/G, I, D/K modes Unweighted SNR Gain limited sensitivity (-1dB video signal) Carrier level of test signal PARAMETER A1 BU4 A1 BU4 0.35 A1 A1 A1 BU4 BU4 BU4 0.0 - 0.5 -1.0 A2 + B1 + B4 BU4 V - 1.5 - 2.5 - 4.0 dB dB 42 40 A1 or A2 or A3 BU4 A2 BU4 TEST SIGNAL TEST 40 dB dB dB 44 dB 33 dBµV MIN. TYP. MAX. UNIT POINT Audio output characteristics Specification valid for : B/G, D/K and I modes AF output level (C7 = 0) measured via LP 20 kHz filter, RMS detector 50µs de-emphasis for AF1 at 1 kHz (C5 = 1, C6 = 1) Specification valid for : L/L’ mode (C5 = 0) modulation = 54% AF output level (C7 = 0) Specification valid for : B/G, D/K, I modes THD (Total Harmonic Distortion) Signal-to –Noise ratio measured via LP 20 kHz filter, RMS detector 50µs de-emphasis for AF1 at 1 kHz (C5 = 1, C6 = 1) Specification valid for : L/L’ mode THD (Total Harmonic Distortion) Signal-to –Noise ratio measured via LP 20 kHz filter, RMS detector for AF1 at 1 kHz Specification valid for : B/G, D/K and I modes (S/N = 40 dB) (C5 = 1, C6 = 1) Audio sensitivity Specification valid for : L/L’ mode (S/N = 38 dB) Audio sensitivity 3139 149 10330 A2 + B3 BU6 400 500 600 mVrms A1 +B2 or A3 + B6 BU6 350 450 550 mVrms 50 0.2 63 0.6 - % dB 42 0.8 50 1.5 - % dB A2 + B3 BU6 A1 + B2 or A3 + B6 BU6 A2 + B3 BU6 40 dBµV A1 + B2 or A3 + B6 BU6 45 dBµV 11 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 APPLICATION INFORMATION DEMONSTRATION KIT A demonstration kit is available for the FQ1216ME (software, Application Note and evaluation board). Please contact your local Sales Engineer for details about the price and availability 2 I C PROGRAMMING 2 For information regarding general aspects of I²C bus control see 'The I C-bus and how to use it', published by Philips Semiconductors under the code : 9398 393 40011. 2 The FQ1216ME contains two I C transceivers, one in the tuner part and one in the IF part. It is imperative to 2 ensure that both I C devices are programmed correctly according to their addresses If in doubt, please refer to the demonstration software. 3139 149 10330 12 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 Tuner Part Programming (Write Mode) BIT ALLOCATION (WRITE MODE , R/W = 0). Write Data MSB bit6 bit5 bit4 bit3 bit2 bit1 LSB ACK Address Byte ADB 1 1 0 0 0 MA1 MA0 R/W=0 A Divider Byte 1 DB1 0 N14 N13 N12 N11 N10 N9 N8 A Divider Byte 2 DB2 N7 N6 N5 N4 N3 N2 N1 N0 A Control Byte 1 CP T2 T1 T0 RSA RSB OS A Bandswitch Byte BB P7 P6 P5 P4 P3 P2 P1 P0 A Auxiliary Byte AB (note *) ATC AL2 AL1 AL0 0 0 0 0 A CB Note *: By default it is set to AL2=0, AL1=1, AL0=0. This sets the tuner TOP to 112 dBuV upon power-on reset. ADDRESS SELECTION (BYTE ADB) Voltage at terminal 6 Address MA1 MA0 0 .......... 0.1 Vcc C0 0 0 0.2..........0.3 Vcc C2 0 1 0.4 ........ 0.6 Vcc C4 1 0 0.9 Vcc ...... 5 V C6 1 1 Note: If the AS pin is left floating, the internal biasing will automatically set the address to C2. PROGRAMMABLE DIVIDER SETTING (BYTES DB1 AND DB2) Divider ratio: N = FOSC/Fss where FOSC = ( FRF + FIF ) and Fss is the step-size set by RSA and RSB as described below. N = 8192*N13 + 4096*N12 + 2048*N11 + 1024*N10 + 512*N9 + 256*N8 + 128*N7 + 64*N6 + 32*N5 + 16*N4 + 8*N3 + 4*N2 + 2*N1 + N0 Note: FIF = 38.9 MHz, except for L' mode. In this case FIF = 33.95 MHz CONTROL BYTE CB Charge Pump Setting: CP can be set to either 0 (low current) or 1 (high current). CP = 1, charge pump current = 280uA results in fastest tuning (default mode) CP = 0 , charge pump current = 60uA results in moderate speed tuning with slightly better residual oscillator Test Mode Setting: T2 = 0, T1 = 0, T0 = 1 for normal operation (default) T2 = 0, T1 = 1, T0 = 1 indicates that Byte AB will follow Byte CB instead of Byte BB for the current IIC Byte sequence. 3139 149 10330 13 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 PLL Disabling: OS=0 OS=1 for normal operation, switches off the PLL tuning amplifier (PLL tuning is disabled) Ratio Select Bits RSA = 0, RSB = 0 RSA = 0, RSB = 1 RSA = 1, RSB = 0 RSA = 1, RSB = 1 gives 50 kHz step-size gives 31.25 kHz step-size (for slow picture-search) gives 166.7 kHz step-size gives 62.5 kHz step-size (for normal picture-search) BANDSWITCHING BYTE BB PORTS P0 P1 P2 P3 P4 P5 P6 P7 LOW BAND 1 0 0 0 0 X X X MID BAND 0 1 0 0 0 X X X HIGH BAND 0 0 1 0 0 X X X AUXILLIARY BYTE AB The AGC Take Over Point can be set by programming the following bits AL2, AL1, AL0 IF output level, symmetrical mode Remark AL2 AL1 AL0 115 dBµV 0 0 0 115 dBµV 0 0 1 112 dBµV default mode at POR 0 1 0 109 dBµV Recommended for negative modulation 0 1 1 106 dBµV Recommended for positive modulation 1 0 0 1 0 1 103 dBµV I AGC = 0 External AGC . See remarks (1) & (3). 1 1 0 3.5 V Disabled . See remarks (2). 1 1 1 Remarks: 1). The AGC detector is disabled. Both the sinking and sourcing current from the IC is disabled. The AGC output goes into a high impedance state and an external AGC source can be connected in parallel and will not be influenced. 2). The AGC detector is disabled and I AGC = 9 µA. Note: The AGC detection system has been changed to the narrowband mode for both negative and positive modulation systems. All new versions carry the code SV21 (old versions carry the code SV20). The settings have been hard-coded inside the modules and customers are not required to change their software to adapt to the new AGC system. 3139 149 10330 14 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 Tuner Part Programming (Read Mode) BIT ALLOCATION (READ MODE R/W = 1) MSB bit6 bit5 bit4 bit3 bit2 bit1 LSB ACK Address Byte ADB 1 1 0 0 0 MA1 MA0 R/W=1 A Status Byte POR FL 1 1 AGC A2 A1 A0 A SB The following data can be read from the device through the status byte: POR (power on reset): POR is internally set to 1 in case Vcc drops below 3V. The POR bit is reset when an end of data is detected by the PLL-IC. FL: in lock flag (FL = 1 when the phase lock loop is in lock). The loop must be phase-locked during at least 8 periods of the internal 7.8125 kHz reference-frequency (i.e. 1 msec) before the FL flag is internally set to 1. AGC : internal AGC flag. AGC=1 when internal AGC is active (level below 3V) A2, A1, A0 : Not used. 3139 149 10330 15 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 IF Part Programming (Write Mode) The IF uses the new TDA9887 demodulation IC from Philips Semiconductors. 2 I C Bus Control –format to WRITE (slave receives data) S SLAVE ADDRESS R/W=0 A BIT SAD A DATA A P FUNCTION S START condition Standard SLAVE ADDRESS 100 0011X where X is the value of R/W ** R/W = 0 Write Mode A acknowledge, generated by slave SUBADDRESS (SAD) See table below DATA Bytes B, C and E (described below) P STOP condition ** Note The FQ1216ME/IV-3 (12 NC = 3139 147 19151) has a fixed IF address of # 84. SUB ADDRESS BYTE (SAD, first byte after slave address) DATA BYTE FOLLOWING SAD SWITCHING (B DATA) ADJUST (C DATA) DATA (E DATA) MSB D7 0 0 0 D6 D5 D4 D3 D2 D1 0 0 0 X 0 0 X 0 0 X 0 0 X 0 0 0 0 1 LSB D0 0 1 0 DESCRIPTION OF THE BITS OF THE VARIOUS DATA BYTES DATA BYTE B DATA C DATA E DATA 3139 149 10330 BIT SUBADDRESS FUNCTION B0 SWITCHING video mode (sound trap) B1 SWITCHING auto mute FM B2 SWITCHING carrier mode B3 and B4 SWITCHING TV standard positive/negative modulation (B3=0) B5 SWITCHING forced mute audio B6 SWITCHING not used B7 SWITCHING L/L’ Sound Co to C4 ADJUST TOP adjustment C5 to C6 ADJUST de-emphasis C7 ADJUST audio gain E0 and E1 DATA standard sound carrier E2 to E4 DATA standard video IF E5 DATA VIF, SIF and tuner minimum gain E6 DATA L standard PLL gating HIGH E7 DATA VIF-AGC 16 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 3139 149 10330 X X X X X 0 Force Audio Mute X X X X X X X X X X X X X X X X X 1 0 0 1 1 0 0 0 0 1 0 0 1 0 1 0 0 1 0 L’ 1 0 1 0 1 0 0 0 1 1 0 0 0 0 0 0 0 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 0 0 0 0 0 0 0 1 0 1 1 1 0 1 0 1 1 0 0 0 0 0 0 0 1 0 1 1 0 L Description VIF AGC Output 1 0 0 1 0 1 IF Gain L/L’ PLL Gating 0 Video IF D/K Sound Intercarrier TV Systems Audio Gain 0 0 1 1 1 0 De-Emphasis De-Emphasis Time 1 0 0 1 0 1 TOP Adjustment 0 L/L’ Sound (OP2) I Not Used (OP1) 0 0 0 0 0 0 Forced Mute Audio 1 0 1 1 1 0 TV Modulation 1 0 0 1 0 0 FM Mode 0 Carrier Mode B/G Auto Mute FM Bits Video Trap Bypass E E E E E E E E C C C C C C C C B B B B B B B B 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 For convenience, the programming has been consolidated as a single table. 17 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 IF Part Programming (Read Mode) The IF uses the new TDA9885 (MP versions) or TDA9886 (ME versions) demodulation IC from Philips Semiconductors. 2 I C Bus Control –format to READ (slave transmits data) S SLAVE ADDRESS R/W=1 A DATA AN P BIT FUNCTION S START condition Standard SLAVE ADDRESS 100 0011X where X is the value of R/W ** R/W = 1 Read Mode A acknowledge, generated by slave DATA AN Byte D (described below) acknowledge not, generated by the master P STOP condition, generated by the master The master generates an acknowledge when it has received the dataword READ. The master next generates an acknowledge, then slave begins transmitting the dataword READ, and so on until the master generates no acknowledge and transmits a STOP condition. ** Note The FQ1216ME/IV-3 (12 NC = 3139 147 19151) has a fixed IF address of # 84. Byte D (Transmitted byte after read condition - Status Register) FUNCTION READ MSB D7 AFCWIN D6 VIFL D5 FMIFL D4 AFC4 D3 AFC3 D2 AFC2 D1 AFC1 LSB D0 PONR PONR = 1 After power-on reset or after supply breakdown PONR = 0 After a successful reading of the status register FMIFL = Not used. VIFL = 1 Video IF level HIGH VIFL = 0 Video IF level LOW 3139 149 10330 18 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 AFC STATUS It is possible to monitor the AFC status via the D1-D4 bits. Function Bits AFC FVIF vs F0 (1) D4 D3 D2 D1 0 1 1 1 FVIF = F0 − 162.5 kHz 0 1 1 0 FVIF = F0 − 137.5 kHz 0 1 0 1 FVIF = F0 − 112.5 kHz 0 1 0 0 FVIF = F0 − 87.5 kHz 0 0 1 1 FVIF = F0 − 62.5 kHz 0 0 1 0 FVIF = F0 − 37.5 kHz 0 0 0 1 0 0 0 0 FVIF = F0 + 12.5 kHz 1 1 1 1 FVIF = F0 + 37.5 kHz 1 1 1 0 FVIF = F0 + 62.5 kHz 1 1 0 1 FVIF = F0 + 87.5 kHz 1 1 0 0 FVIF = F0 + 112.5 kHz 1 0 1 1 FVIF = F0 + 137.5 kHz 1 0 1 0 FVIF = F0 + 162.5 kHz 1 0 0 1 FVIF ≥ F0 + 187.5 kHz 1 0 0 0 FVIF ≤ FVIF F0− 187.5 kHz = F0 − 12.5 kHz Note 1. F0 = nominal FVIF AFCWIN = 1 FVIF inside AFC Window AFCWIN = 0 FVIF outside AFC Window PROGRAMMING EXAMPLES Example 1: To tune to Ch E21 (471.25 MHz) in high band Fosc = 471.25 + 38.9 = 510.15 MHz N = (510.15 MHz) / (62.5 kHz) = 1F E2 (Hexadecimal) So DB1 = 1F H and DB2 = E2 H CB = 86H if CP is set to low or CB = C6H if CP is set to high BB = 44H (because of high band selected) 3139 149 10330 19 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 Example 2 : To tune to a PAL B/G program at 471.25 MHz 2 IF I C program 2 Tuner I C program Example 3 : To tune to a SECAM program at 471.25 MHz (L system) 2 IF I C program 2 Tuner I C program 3139 149 10330 20 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 2 LOADING OF I C BUS The FQ1216ME contains series impedances in the SCL and SDA lines : a total of R= 220 ohms leading to the tuner part and R= 300 ohms leading to the IF demodulation part. See the diagram below. Both lines also have capacitive loads of C= 22 pF max. Care must be taken to ensure that the total load on the bus does not 2 exceed that as mentioned in the brochure "The I C-bus and how to use it". 100 120 SDA 100 180 180 120 SCL AUDIO EMPHASIS The audio de-emphasis (50 us) is set by the bits C5 and C6 C5=0 de-emphasis OFF C5=1 de-emphasis ON C6=1 50us C6=0 75 us De-emphasis should be switched off in L/L’ mode since it is not required for AM sound. CVBS LOAD / TUNING VOLTAGE SUPPLY A video buffer is built into the frontend to enable the unit to drive a 75 Ω load directly (e.g. into the SAA711x directly). A DC-DC converter for providing the required tuning voltage supply is already built into the FQ1216ME. PIP APPLICATION The FQ1216ME has a second user-defined address for the IF circuit. By setting a 2K2 resistor at pin 10, the AFRIC address is set to # 84. In the same manner, with a 1K resistor to ground at pin 6, the tuner is set to an address of # C0. The other FQ1216ME Mk3 remains unchanged with an address of # C2 and # 86 respectively. An example is shown below. PIP Frontend Address: # C0 and # 84 FQ1216ME /PH-3 1 Active Splitter Module 6 10 1K0 2K2 Main Frontend Address: # C2 and # 86 FQ1216ME/PH-3 3139 149 10330 21 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 CVBS Output level CVBS at pin 12 (into 75 ohm load) V dc 1.35 V 1 Vpp 0.65 V 0.35 V VIDEO SIGNAL TO NOISE RATIO V i d e o S ig n a l-t o - N o is e R a t io ( W e ig h te d ) @ C h 2 1 65 60 55 50 SNR dB 45 40 35 30 25 20 15 10 10 20 30 40 50 60 70 80 90 100 110 In p u t L ev e l d B u V 3139 149 10330 22 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 MECHANICAL DATA See product drawing 3139 149 0120 AERIAL CONNECTIONS Standard connector in accordance with type order information found on Page 2 and drawings found on Page 25. SOLDERABILITY The solderability of pins and mounting tags when tested initially and after 16 hour steam ageing in accordance with “IEC 60068-2-20”, test Ta, method 1 (solder bath 235°C for 2s), results in a wetted area of 95%. No de-wetting will occur when soldered at 260°C for 5s. RESISTANCE TO SOLDERING HEAT The product will not be damaged when tested in accordance with “IEC 60068-2-20”, test Tb, ,method 1A (solder bath 260°C for 10±1 s). MASS ROBUSTNESS OF PINS The pins will not be damaged when tested in accordance with “IEC 60068-2-21”: • Test Ua1, tensile of 10N in axial direction • Test Ua2, thrust of 4N in axial direction PUNCHING PATTERN OF CHASSIS PCB For optimum mounting of the tuner to a PCB, the punching pattern is recommended (see 3139 149 0120). The tuner must be mounted without clearance between the tuner supporting surface and the printed circuit board (PCB). When mounted in this way, the tuner must be soldered to the PCB. This can be achieved by pressing the unit vertically onto the PCB during soldering. Approximately 45g. PACKAGING INFO The products are packed in the carton box and transferred to customers by Pallet Transport. Mounting Type Dimension B x w x h (cm) No. of sets Example of Carton Box: b Gross Wt (Kg) Horizontalmount type Carton 46 x 34 x 5.4 40 2.34 Pallet 120 x 105 x 105 4280 272.38 Verticalmount type Carton 46 x 34 x 10.2 120 6.38 Pallet 120 x 105 x 105 6960 392.04 Carton Boxes are made of Corrugated Fibreboard which are free of environmentally banned substances. 3139 149 10330 23 w h Rev g : 16.02.2004 Multi-Standard Desktop Video Module 3139 149 10330 FQ1216ME MK3 24 Rev g : 16.02.2004 Multi-Standard Desktop Video Module 3139 149 10330 FQ1216ME MK3 25 Rev g : 16.02.2004 Multi-Standard Desktop Video Module 3139 149 10330 FQ1216ME MK3 26 Rev g : 16.02.2004 Multi-Standard Desktop Video Module 3139 149 10330 FQ1216ME MK3 27 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 Document revision history Rev # Date Approved by Remarks 0 20-02-01 Toh Kong Lim New 0.1 16-04-01 Toh Kong Lim Trigger by Soh KL, changes in page 18 0.2 17-07-01 Toh Kong Lim Trigger by Toh KL, changes in pg 10-13, 16-19 Toh Kong Lim Trigger by Paxton Tan, changes in pg 11-20 and product drawings. 0.3 18-10-01 0.3 10-12-01 Updating last page 0.3 28-02-02 Updating last page 0.4 01-04-02 Toh Kong Lim 1 06-05-02 Toh Kong Lim 1 15-05-02 Toh Kong Lim 1.1 21-06-02 Toh Kong Lim 1.2 15-07-02 Toh Kong Lim 1.3 - - 1.4 20-09-02 Toh Kong Lim b 18-12-02 Toh Kong Lim Updating front and last page Trigger by Toh KL, changes in pg 2 Trigger by Soh KL, product drawings changed under CP 63459 Trigger by Paxton Tan, changes in pg 2 (1 new model added), pg 3 (Channel Coverage) and product drawings. Data sheet updated by Paxton, changes in pg 2, 3, 4, 5, 8, 10, 13, 14, 15, 20, 22 & prod. dwgs. Trigger by Toh KL, updating pg 10 (Audio output characteristics) no change Trigger by Toh KL, updating pg 9, 10 & last page. c 15-07-03 Toh Kong Lim Updating last page & Pg 13 : 1) change of TOP to a lower value; 2) set ATC = 0 d 01-10-03 Toh Kong Lim Trigger by Soh KL, updating mechanical drawings e 10-11-03 Toh Kong Lim f 10-02-04 Toh Kong Lim g 16-02-04 Toh Kong Lim 3139 149 10330 Triggered by Toh KL; Pg 2, 3, 13, 15, 17 : remarks added. 2 Pg 20 : Adding I C drawing and PIP drawing; Trigger by Toh KL; nd Pg 2 : features description add - User-settable 2 IF address for PIP application and ordering information description changed. Pg 3 : description add - For all others, a second address can be set by using a 2K2 resistor at 10 of the module. All modules use the narrowband AGC detection system. Pg 14 : add notes. Trigger by Toh KL; Pg 14 – notes – all new versions carry the code SV21 instead of SV22 with effect from 1 April 2004 28 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specification. Application Information Where application information is given, it is advisory and does not form part of the specification LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 2 PURCHASE OF PHILIPS I C COMPONENTS 2 2 Purchase of Philips I C components conveys a license under the Philips I C patent to use 2 2 the components in the I C systems to the I C specification defined by Philips. This specification can be ordered using the code 9398 393 40011. 3139 149 10330 29 Rev g : 16.02.2004 Philips RF Solutions Product specification Multi-Standard Desktop Video Module FQ1216ME MK3 RF Solutions Sales Offices Brazil: Philips RF Solutions, Tel: +55 11 2125 0833, Fax: +55 11 2125 0828 China: Philips RF Solutions, Tel. +86 21 6354 1088, ext. 5806, Fax. +86 21 6354 1060 (Shanghai) Tel: +86 512 6824 6688 ext 3786, Fax: +86 512 6825 0413 (Suzhou) Germany: Philips RF Solutions, Tel. +49 170 203 230 8, Fax. +49 221 2854452 Hong Kong: Philips RF Solutions, Tel. +852 2666 2809, Fax. +852 2666 2814 India: Philips RF Solutions, Tel. +91 22 5 691 2127, Fax. +91 22 5 691 2184 Korea (Republic of): Philips RF Solutions, Tel. +82 2 709 1475, Fax. +82 2 709 1480 Spain: Philips RF Solutions, Tel. +34 93 270 4059, Fax. +34 93 270 4012 Taiwan: Philips RF Solutions, Tel. +886 2 3789 2388, Fax. +886 2 3789 2394 Turkey: Philips RF Solutions, Tel. +90 216 522 1799, Fax. +90 216 522 1813 United States: Philips RF Solutions, Tel. +1 734 944 4299, Fax. +1 734 944 4427 For all other countries apply to: Philips RF Solutions Prof. Holstlaan 4, Building WL 5656 AA Eindhoven, The Netherlands Tel. +31 40 27 45 799, Fax. +31 40 27 43 653 Internet: www.rfsolutions.philips.com © Philips Electronics N.V. 2004. All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. 3139 149 10330 30 Rev g : 16.02.2004