Product Folder Sample & Buy Support & Community Tools & Software Technical Documents LM1771 SNVS446D – JUNE 2006 – REVISED JANUARY 2016 LM1771 Low-Voltage Synchronous Buck Controller With Precision Enable and No External Compensation 1 Features 3 Description • • • • • • • • • The LM1771 device is an efficient synchronous buck switching controller with a precision enable requiring no external compensation. The constant ON-time control scheme provides a simple design free of compensation components, allowing minimal component count and board space. The precision enable pin allows flexibility in sequencing multiple rails and setting UVLO. The LM1771 also incorporates a unique input feedforward to maintain a constant frequency independent of the input voltage. The LM1771 is optimized for a low-voltage input range of 2.8 V to 5.5 V and can provide an adjustable output as low as 0.8 V. Driving an external high-side PFET and low-side NFET, it can provide efficiencies as high as 95%. 1 Input Voltage Range of 2.8 V to 5.5 V 0.8-V Reference Voltage Precision Enable No Compensation Required Constant Frequency Across Input Range Low Quiescent Current of 400 µA Internal Soft-Start Short Circuit Protection 6-Pin WSON Package and 8-Pin VSSOP Package 2 Applications • • • • • • • • Simple-to-Design, High-Efficiency, Step-Down Switching Regulators FPGAs, DSPs, and ASIC Power Supplies Set-Top Boxes Cable Modems Printers Digital Video Recorders Servers Graphic Cards Three versions of the LM1771 are available depending on the switching frequency desired for the application. Nominal switching frequencies are in the range of 100 kHz to 1000 kHz. Device Information(1) PART NUMBER LM1771 PACKAGE BODY SIZE (NOM) WSON (6) 3.00 mm × 3.00 mm VSSOP (8) 3.00 mm × 3.00 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. Typical Application Circuit VIN VIN EN HG EN LM1771 VOUT LG FB GND 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LM1771 SNVS446D – JUNE 2006 – REVISED JANUARY 2016 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 4 6.1 6.2 6.3 6.4 6.5 6.6 4 4 4 4 5 6 Absolute Maximum Ratings ..................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics........................................... Typical Characteristics .............................................. Detailed Description .............................................. 9 7.1 7.2 7.3 7.4 Overview ................................................................... 9 Functional Block Diagram ......................................... 9 Feature Description................................................. 10 Device Functional Modes........................................ 12 8 Application and Implementation ........................ 13 8.1 Application Information............................................ 13 8.2 Typical Applications ................................................ 13 9 Power Supply Recommendations...................... 20 10 Layout................................................................... 21 10.1 Layout Guidelines ................................................. 21 10.2 Layout Examples................................................... 21 10.3 Thermal Considerations ........................................ 22 11 Device and Documentation Support ................. 23 11.1 11.2 11.3 11.4 11.5 11.6 Device Support .................................................... Documentation Support ........................................ Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 23 23 23 23 23 23 12 Mechanical, Packaging, and Orderable Information ........................................................... 23 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision C (April 2013) to Revision D • Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section. ................................................................................................ 1 Changes from Revision B (April 2013) to Revision C • 2 Page Page Changed layout of National Data Sheet to TI format ........................................................................................................... 22 Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 LM1771 www.ti.com SNVS446D – JUNE 2006 – REVISED JANUARY 2016 5 Pin Configuration and Functions NGG Package 6-Pin WSON Top View FB 1 GND 2 HG 3 DAP 6 EN 5 VIN 4 LG DGK Package 8-Pin VSSOP Top View 1 2 FB EN GND VIN GND VIN 3 4 HG 8 LG 7 6 5 Pin Functions PIN NAME TYPE (1) DESCRIPTION WSON VSSOP DAP — — GND EN 6 8 I Enable Pin FB 1 1 A Feedback Pin GND 2 2, 3 GND HG 3 4 AO PFET Gate Drive LG 4 5 AO NFET Gate Drive VIN 5 6, 7 PWR (1) Die Attach Pad is internally connected to GND, but it cannot be used as the primary GND connection Ground Input Supply I = Input, A = Analog, GND = Ground, AO = Analog output, PWR = Power Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 3 LM1771 SNVS446D – JUNE 2006 – REVISED JANUARY 2016 www.ti.com 6 Specifications 6.1 Absolute Maximum Ratings (1) (2) See MIN MAX UNIT VIN –0.3 6 V EN, FB, HG, LG –0.3 Junction temperature Lead temperature Soldering, 10 sec Storage temperature, Tstg (1) (2) –65 VIN V 150 °C 260 °C 150 °C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. 6.2 ESD Ratings V(ESD) (1) Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) Electrostatic discharge VALUE UNIT ±2000 V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions MIN VIN to GND Junction temperature, TJ MAX UNIT 2.8 5.5 V −40 125 °C 6.4 Thermal Information LM1771 THERMAL METRIC (1) NGG (WSON) DGK (VSSOP) 6 PINS 8 PINS UNIT RθJA Junction-to-ambient thermal resistance 52.8 169.2 °C/W RθJC(top) Junction-to-case (top) thermal resistance 51.4 59.7 °C/W RθJB Junction-to-board thermal resistance 27.2 89.3 °C/W ψJT Junction-to-top characterization parameter 0.7 7.0 °C/W ψJB Junction-to-board characterization parameter 27.3 87.9 °C/W RθJC(bot) Junction-to-case (bottom) thermal resistance 7.4 N/A °C/W (1) 4 For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953. Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 LM1771 www.ti.com SNVS446D – JUNE 2006 – REVISED JANUARY 2016 6.5 Electrical Characteristics Specifications are for TJ = 25°C. All maximum and minimum limits apply over the full junction temperature range (−40°C to +125°C), unless otherwise specified. Minimum and maximum limits are ensured through test, design or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C and are provided for reference purposes only. Unless otherwise specified, VIN = 3.3 V. PARAMETER VFB Feedback pin voltage IQ Quiescent current TON TEST CONDITIONS 0.782 VFB = 0.9 V Switch ON-time TOFF_MIN MIN Minimum OFF-time TYP MAX 0.8 0.818 V 400 700 µA LM1771S - (500 ns) 0.4 0.5 0.6 LM1771T - (1000 ns) 0.8 1 1.2 LM1771U - (2000 ns) 1.6 2 2.4 LM1771S - (500 ns) 150 250 LM1771T - (1000 ns) 135 225 LM1771U - (2000 ns) 120 220 TD Gate drive dead-time VIH_EN EN pin rising threshold VEN_HYS EN pin hysteresis IFB Feedback pin bias current VFB = 0.9 V VUVLO Undervoltage lockout VIN Rising Edge VUVLO_HYS Undervoltage lockout hysteresis VSC_TH Feedback pin short circuit latch threshold UNIT 70 1.15 ns ns 1.2 1.25 V 50 200 mV 50 2.65 nA 2.8 50 0.42 µs 0.55 V mV 0.65 V RDS(ON) 1 HG FET driver pullup ON-resistance IHG = 20 mA 4 Ω RDS(ON) 2 HG FET driver pulldown ON-resistance IHG = 20 mA 6 Ω 3 LG FET driver pullup ON-resistance ILG = 20 mA 4 Ω 4 LG FET driver pulldown ON-resistance ILG = 20 mA 6 Ω RDS(ON) RDS(ON) Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 5 LM1771 SNVS446D – JUNE 2006 – REVISED JANUARY 2016 www.ti.com 6.6 Typical Characteristics All curves taken at VIN = 3.3 V with configuration in typical application circuit shown in Typical Applications. TJ = 25°C, unless otherwise specified. 6 Figure 1. TON vs VIN (LM1771S) Figure 2. TON vs VIN (LM1771T) Figure 3. TON vs VIN (LM1771U) Figure 4. TON vs Temperature (LM1771S) Figure 5. TON vs Temperature (LM1771T) Figure 6. TON vs Temperature (LM1771U) Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 LM1771 www.ti.com SNVS446D – JUNE 2006 – REVISED JANUARY 2016 Typical Characteristics (continued) All curves taken at VIN = 3.3 V with configuration in typical application circuit shown in Typical Applications. TJ = 25°C, unless otherwise specified. Figure 7. TOFF vs Temperature (LM1771S) Figure 8. TOFF vs Temperature (LM1771T) Figure 9. TOFF vs Temperature (LM1771U) Figure 10. Feedback Voltage vs Temperature Figure 11. VEN Threshold vs Temperature Figure 12. Short-Circuit Threshold vs Temperature Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 7 LM1771 SNVS446D – JUNE 2006 – REVISED JANUARY 2016 www.ti.com Typical Characteristics (continued) All curves taken at VIN = 3.3 V with configuration in typical application circuit shown in Typical Applications. TJ = 25°C, unless otherwise specified. Figure 13. Quiescent Current vs Temperature VIN = 5 V VOUT = 1.8 V FSW = 545 kHz Figure 14. Dead-Time vs Temperature VIN = 5 V Figure 15. Efficiency vs IOUT (LM1771T) VIN = 5 V VOUT = 3.3 V FSW = 500 kHz FSW = 379 kHz Figure 16. Efficiency vs IOUT (LM1771U) VIN = 5 V Figure 17. Efficiency vs IOUT (LM1771U) 8 VOUT = 2.5 V Submit Documentation Feedback VOUT = 1.2 V FSW = 727 kHz Figure 18. Efficiency vs IOUT (LM1771S) Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 LM1771 www.ti.com SNVS446D – JUNE 2006 – REVISED JANUARY 2016 7 Detailed Description 7.1 Overview The LM1771 synchronous buck controller has a control scheme that is referred to as adaptive ON-time control. This topology relies on a fixed switch ON-time to regulate the output voltage. This ON-time is internally set by EEPROM and is available with three different set-points to allow for different frequency options. The LM1771 automatically adjusts the ON-time during operation inversely with the input voltage (VIN) to maintain a constant frequency. Therefore the switching frequency during continuous conduction mode is independent of the inductor and capacitor size unlike hysteretic switchers. At the beginning of the cycle, the LM1771 turns on the high-side PFET for a fixed duration. This ON-time is predetermined (internally set by EEPROM and adjusted by VIN) and the switch does not turn off until the timer has completed its period. The PFET then turns off for a minimum predetermined time period. This minimum TOFF of 150 ns is internally set and cannot be adjusted. This is to prevent false triggering from occurring on the comparator due to noise from the SW node transition. After the minimum TOFF period has expired, the PFET remains off until the comparator trip-point has been reached. Upon passing this trip-point (set at 0.8 V at the feedback pin), the PFET turns back on and the process repeats, thus regulating the output. The NFET control is complementary to the PFET control with the exception of a short dead-time to prevent shoot-through from occurring. 7.2 Functional Block Diagram LM1771 VIN ON TIMER Vin Q UVLO OFF TIMER SD Q 0.8V Level Shift and Shoot Through Protection R Q S FB Q REGULATION COMPARATOR 0.55 V High-Side Driver Low-Side Driver HG LG SD UVLO SHORT CIRCUIT PROTECTION R Q S /Soft-Start Q EN 1.2 V ENABLE COMPARATOR GND Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 9 LM1771 SNVS446D – JUNE 2006 – REVISED JANUARY 2016 www.ti.com 7.3 Feature Description 7.3.1 Timing Opinion Three versions of the LM1771 are available each with a predetermined TON set internally by EEPROM. This TON setting determines the switching frequency for the application. Derivation and calculation of the dependence of the switching frequency on VIN and TON is shown in Equation 1 through Equation 6. In a PWM buck switcher, Equation 1, Equation 2, and Equation 3 can be manipulated to obtain the switching frequency. Equation 1 shows the standard duty-cycle equation given by the volts-seconds balance on the inductor with Equation 2 and Equation 3 defining standard relationships: D= VOUT VIN TON = D x TP (1) (2) 1 fSW (3) TP = Using these equations and solving for duty-cycle for Equation 4: D = fSW x TON (4) Frequency can now be expressed in Equation 5: F= VOUT VIN x TON (5) Or simply written as Equation 6: fSW = VOUT D where • α = VIN x TON (6) To maintain a set frequency in an application, α is always held constant by varying TON inversely with VIN. The three versions of the LM1771 are identified by the ON-times at a VIN of 3.3 V for consistency. For clarification, see Table 1. Table 1. Timing for All Variants Product ID TON at 3.3 V α (V µs) LM1771S 0.5 µs 1.65 LM1771T 1.0 µs 3.3 LM1771U 2.0 µs 6.6 The variation of TON versus VIN can also be expressed graphically. These graphs can be found in the Typical Characteristics of the data sheet. With α being a constant regardless of the version of the LM1771 used, Equation 6 shows that the only dependent variable remaining is VOUT. Because VOUT is a constant in any application, the frequency also remains constant. The switching frequency at which the application runs depends upon the VOUT desired and the LM1771 version chosen. For any VOUT, three frequency options (LM1771 versions) can be selected. This can be seen Table 2. The recommended frequency range of operation is 100 kHz to 1000 kHz. 10 Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 LM1771 www.ti.com SNVS446D – JUNE 2006 – REVISED JANUARY 2016 Table 2. Frequency vs VOUT for Variants VOUT (1) TIMING OPTIONS (1) 500 ns 1000 ns 2000 ns 0.8 485 242 121 1 606 303 152 1.2 727 364 182 1.5 909 455 227 1.8 1091 545 273 2.5 1515 758 379 3.3 2000 1000 500 Switching Frequency (kHz) of LM1771 based on output voltage and timing option. 7.3.2 Short-Circuit Protection The LM1771 has an internal short-circuit comparator that constantly monitors the feedback node (except during soft-start). If the feedback voltage drops below 0.55 V (equivalent to the output voltage dropping below 68% of nominal), the comparator trips causing the part to latch off. The LM1771 does not resume switching until the input voltage is taken below the UVLO threshold and then brought back into its normal operating range, or the part is disabled then re-enabled through the enable pin. The purpose of this function is to prevent a severe short circuit from causing damage to the application. Due to the fast transient response of the LM1771 a severe short on the output causing the feedback to drop would only occur if the load applied had an effective resistance that approaches the PMOS RDS(ON). 7.3.3 Precision Enable The LM1771 features a precision enable circuit. If the voltage on the EN pin is 1.2 V or greater, the part is enabled and switching occurs. If the enable voltage falls below 1.2 V, the part is placed into a shutdown state and the drivers is tri-stated. This allows the LM1771 to be easily sequenced using a resistive divider from the output of another regulator, or the working input voltage range of the LM1771 to be set using a resistive divider on VIN. There is no internal pullup connected to the EN pin, so an external signal is required to initiate switching. NOTE When power is first applied to the LM1771, there is a slight delay before the enable comparator is functional. During this delay, typically on the order of 400 µs, the part is disabled regardless of the voltage on the EN pin. The falling enable threshold features 50 mV of hysteresis 7.3.4 Soft-Start To limit in-rush current and allow for a controlled start-up the LM1771 incorporates an internal soft-start scheme. Every time the enable voltage rises above 1.2 V while VIN is greater than the UVLO threshold, the LM1771 goes through an adaptive soft-start that limits the ON-time and expands the minimum OFF-time. In addition the part only activates the PMOS allowing a discontinuous mode of operation enabling a prebiased start-up. The time spent in soft-start depends on the load applied to the output, but is usually close to a set time that is dependent on the timing option. The approximate soft-start time can be seen in Table 3 for each timing option. Table 3. Soft-Start Timing for All Variants PRODUCT ID TIMING TSS LM1771S 0.5 µs 1 ms LM1771T 1.0 µs 1.2 ms LM1771U 2.0 µs 1.8 ms Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 11 LM1771 SNVS446D – JUNE 2006 – REVISED JANUARY 2016 www.ti.com Therefore, if the input supply is extremely slow rising such that at the end of soft-start the input voltage is still near the UVLO threshold, a timing option must be chosen to ensure that maximum duty-cycle permits the output to meet the minimum condition. TI recommends using the 2000-ns option (LM1771U) in conditions where the output voltage is 2.5 V or greater to avoid false latch-offs when there is concern regarding the input supply slew rate. NOTE As soon as soft-start terminates the short-circuit protection is enabled. This means that if the output voltage does not reach at least 68% of its final value the part latches off. In some situations, the internal soft-start routine can create a slight overshoot on the output voltage. If this must be avoided, the use of a feedforward capacitor as detailed in the Feedforward Capacitor section. 7.3.5 Jitter The LM1771 uses an adaptive ON-time control scheme that relies on the output voltage ripple to provide a consistent switching frequency. Under certain conditions, excessive noise can couple onto the feedback pin causing the switch node to appear to have a slight amount of jitter. This is not indicative of an unstable design. The output voltage still regulates to the exact same value. Careful component selection and layout must minimize any external influence. In addition to any external noise that can add to the jitter seen on the switch node, the LM1771 always has a slight amount of switch jitter. This is because the LM1771 makes a small alteration in the reference voltage every 128 cycles to improve its accuracy and long-term performance. This has the effect of causing a change in the switching frequency at that instant. When viewed on an oscilloscope this can be seen as a jitter in the switch node. The change in feedback voltage or output voltage, however, is almost indistinguishable. 7.4 Device Functional Modes The LM1771 has essentially one normal operational mode: in normal operation, the part operates in full synchronous mode to regulate the FB input to 0.8 V (typical) after soft-start period is over. The EN pin allows the user to shut down the part. When the part is enabled, the IC enters soft-start for 1 ms to 1.8 ms depending on the variant of the IC. See Soft-Start for more detail on the soft-start pattern. 12 Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 LM1771 www.ti.com SNVS446D – JUNE 2006 – REVISED JANUARY 2016 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers must validate and test their design implementation to confirm system functionality. 8.1 Application Information Design Guide details the design procedure to follow for the typical application. Because of the nature of constant ON-time controller, a certain degree of iteration might be necessary on the sizing of some key components to achieve optimal response, such as the inductor L1. 8.2 Typical Applications 8.2.1 LM1771 Typical Application VIN CIN VIN EN HG EN Q1 L1 LM1771 VOUT LG Q2 RSNS CFF RFB1 COUT FB RFB2 GND Figure 19. Example Circuit Schematic 8.2.1.1 Design Requirements The main parameters needed to successfully design an application based on the LM1171 are typical of buck DC–DC converters. The input and output voltage must be known as well as the worst-case input voltage operating conditions. The maximum output current helps the designer size the inductor appropriately. In addition, the designer needs to be aware of the requirement on the output capacitor to achieve stable operation. See Output Capacitor for details on the output capacitor requirements. 8.2.1.2 Detailed Design Procedure 8.2.1.2.1 Design Guide As with any DC–DC converter, numerous trade-offs are possible to optimize the design for efficiency, size, or performance. These are taken into account and highlighted throughout this discussion. Equation 7 calculates for any buck converter is duty-cycle. Ignoring conduction losses associated with the FETs and parasitic resistances it can be approximated by: D= VOUT VIN (7) A more accurate calculation for duty-cycle can be used that takes into account the voltage drops across the FETs. Equation 8 determines the slight load dependency on switch frequency if needed. Otherwise the simplified equation works well for component calculation. Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 13 LM1771 SNVS446D – JUNE 2006 – REVISED JANUARY 2016 www.ti.com Typical Applications (continued) D= VOUT + VDS_NMOS VIN + VDS_NMOS + VDS_PMOS (8) 8.2.1.2.1.1 Frequency Selection The LM1771 is available with three preset timing options that select the ON-time and hence determine the switching frequency of the application. Increasing the switching frequency has the effect of reducing the inductor size needed for the application while requiring a slight trade-off in efficiency. Table 4 shows the same frequency table as shown earlier (Table 2) with the exception that the recommended timing option for each VOUT is highlighted. TI does not recommend using a high switching frequency with VOUT equal to or greater than 2.5 V due to the maximum duty-cycle limitations of the device coupled with the internal start-up. Table 4. Recommended Switching Frequency vs VOUT VOUT (1) TIMING OPTIONS (1) 500 ns 1000 ns 2000 ns 0.8 485 242 - 1 606 303 - 1.2 727 364 - 1.5 909 455 2237 1.8 - 545 273 2.5 - - 379 3.3 - - 500 Recommended switching frequency (kHz) based on output voltage and timing option. 8.2.1.2.1.2 Inductor Selection The inductor selection is an iterative process likely requiring several passes before settling on a final value. The reason for this is because it influences the amount of ripple seen at the output, a critical component to ensure general stability of an adaptive ON-time circuit. For the first pass at inductor selection the value can be obtained by targeting a maximum peak-to-peak ripple current equal to 30% of the maximum load current. The inductor current ripple (ΔIL) can be calculated by Equation 9: 'IL = (VIN ± VOUT) x D L x fSW (9) Therefore, L can be initially set by applying the 30% rule in Equation 10: L= (VIN ± VOUT) x D 0.3 x fSW x IOUT (10) The other features of the inductor that can be selected besides inductance value are saturation current and core material. Because the LM1771 does not have a current limit, TI recommends having a saturation current higher than the maximum output current to handle any ripple or momentary overcurrent events. The core material also influences the saturation characteristics as ferrite materials have a hard saturation curve and take care that they never saturate during normal use. A shielded inductor or low-profile unshielded inductor is recommended to reduce EMI. This also helps prevent any spurious noise from picking up on the feedback node resulting in unexpected tripping of the feedback comparator. 8.2.1.2.1.3 Output Capacitor One of the most important components to select with the LM1771 is the output capacitor. This is because its size and ESR have a direct effect on the stability of the loop. A constant ON-time control scheme works by sensing the output voltage ripple and switching the FETs appropriately. The output voltage ripple on a buck converter can be approximated by stating that the AC inductor ripple flows entirely into the output capacitor and is created by the ESR of the capacitor. This can be expressed in Equation 11: ΔVOUT = ΔIL x RESR 14 (11) Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 LM1771 www.ti.com SNVS446D – JUNE 2006 – REVISED JANUARY 2016 To ensure stability, two constraints need to be met. The first is that there is sufficient ESR to create enough voltage ripple at the feedback pin. TI recommends having at least 10 mV of ripple seen at the feedback pin. This can be calculated by multiplying the output voltage ripple by the gain seen through the feedback resistors. This gain, H, can be calculated in Equation 12: H= VFB VOUT = 0.8V VOUT (12) If the output voltage is fairly high, causing significant attenuation through the feedback resistors, a feedforward capacitor can be used. This is actually recommended for most circuits as it improves performance. See the Feedforward Capacitor section for more details. The second criteria is to ensure that there is sufficient ripple at the output that is in-phase with the switch. The problem exists that there is actually ripple caused by the capacitor charging and discharging, not only the ESR ripple. Because these are effectively out of phase, problems can exist. To avoid this issue, TI recommends that the ratio of the two ripples (β) is always greater than 5. To calculate the minimum ESR value needed, Equation 13 can be used: § ¨ © 'IL2 ICIN_RMS = IOUT D §¨1 - D + © 12 x IOUT2 (13) In general, the best capacitors to use are chemistries that have a known and consistent ESR across the entire operating temperature range. Tantalum capacitors or similar chemistries such as Niobium Oxide perform well along with certain families of Aluminum Electrolytics. Small value POSCAPs and SP CAPs also work as they have sufficient ESR. When used in conjunction with a low-value inductor it is possible to have an extremely stable design. The only capacitors that require modification to the circuit are ceramic capacitors. Ceramic capacitors cause problems meeting both criteria because they have low ESR and low capacitance. Therefore, if they are to be used, an external ESR resistor (RSNS) must be added. This can be seen in Figure 20. VIN CIN VIN EN HG EN Q1 L1 LM1771 RSNS VOUT COUT LG Q2 CFF RFB1 FB RFB2 GND Figure 20. LM1771 With an External ESR Resistor (RSNS) This circuit uses an additional resistor in series with the inductor to add ripple at the output. It is placed in this location and used in combination with the feedforward capacitor (CFF) to provide ripple to the feedback pin, without adding ripple or a DC offset to the output. The benefit of using a ceramic capacitor is still obtained with this technique. Because the addition of the resistor results in power loss, this circuit implementation is only recommended for low currents (2 A and below). The power loss and rating of the resistor must be taken into account when selecting this component. This circuit implementation using the feedforward capacitor begins to experience limitations when the output voltage is small. Previously the circuit relied on the CFF for all the ripple at the feedback node by assuming that the resistor divider was negligible. As VOUT decreases this can not be assumed. The resistor divider contributes a larger amount of ripple which is problematic as it is also out of phase. Therefore the resistor location must be changed to be in series with the output capacitor. This can be viewed as adding an effective ESR to the output capacitor. This can be seen in Figure 21. Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 15 LM1771 SNVS446D – JUNE 2006 – REVISED JANUARY 2016 www.ti.com VIN CIN VIN EN HG EN Q1 L1 LM1771 VOUT LG Q2 RSNS RFB1 COUT FB RFB2 GND Figure 21. LM1771 With ESR Resistor (RSNS) in Series With Output Capacitor 8.2.1.2.1.4 Feedforward Capacitor The feedforward capacitor is used across the top feedback resistor to provide a lower impedance path for the high-frequency ripple without degrading the DC accuracy. Typically the value for this capacitor must be small enough to prevent load transient errors because of the discharging time, but large enough to prevent attenuation of the ripple voltage. In general a small ceramic capacitor in the range of 1 nF to 10 nF is sufficient. If CFF is used then it can be assumed that the ripple voltage seen at the feedback pin is the same as the ripple voltage at the output. The attenuation factor H no longer needs to be used. However, in these conditions, TI recommends having a minimum of 20-mV ripple at the feedback pin. The use of a CFF capacitor is recommended as it improves the regulation and stability of the design. However, its benefit is diminished as VOUT starts approaching VREF , therefore it is not needed in this situation. 8.2.1.2.1.5 Input Capacitor The dominating factor that usually sets the size of an input capacitor is the current handling ability. This is usually determined by the package size and ESR of the capacitor. If these two criteria are met then there usually must be enough capacitance to prevent impedance interactions with the source. In general, TI recommends using a ceramic capacitor for the input as they provide a low impedance and small footprint. NOTE Use a good dielectric for the ceramic capacitor such as X5R or X7R. These provide better over temperature performance and also minimize the DC voltage derating that occurs on Y5V capacitors. To calculate the input capacitor RMS current, Equation 14 can be used: § ¨ © 'IL2 ICIN_RMS = IOUT D §¨1 - D + © 12 x IOUT2 (14) which can be approximated by, Equation 15 ICIN_RMS = IOUT x D(1 - D) (15) 8.2.1.2.2 MOSFET Selection The two FETs used in the LM1771 requires attention to selection of parameters to ensure optimal performance of the power supply. The high-side FET must be a PFET and the low-side an NFET. These can be integrated in one package or as two separate packages. 16 Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 LM1771 www.ti.com SNVS446D – JUNE 2006 – REVISED JANUARY 2016 8.2.1.2.2.1 VDS Voltage Rating The first selection criteria is to select FETs that have sufficient VDS voltage ratings to handle the maximum voltage seen at the input plus any transient spikes that can occur from parasitic ringing. In general most FETs available for this application have ratings from 8 V to 20 V. If a larger voltage rating is used then the performance is most likely be degraded because of higher gate capacitance. 8.2.1.2.2.2 RDSON The RDS(ON) specification is important as it determines several attributes of the FET and the overall power supply. The first is that it sets the maximum current of the FET for a given package. A lower RDS(ON) permits a higher allowable current and reduce conduction losses, however, it increases the gate capacitance and the switching losses. 8.2.1.2.2.3 Gate Drive The next step is to ensure that the FETs are capable of switching at the low Vin supplies used by the LM1771. The FET must have the Rdson specified at either 1.8 V or 2.5 V to ensure that it can switch effectively as soon as the LM1771 starts up. 8.2.1.2.2.4 Gate Charge Because the LM1771 uses a fixed dead-time scheme to prevent cross conduction, the FET transitions must occur in this time. The rise and fall time of the FETs gate can be influenced by several factors including the gate capacitance. Therefore the total gate charge of both FETs must be limited to less than 20 nC at 4.5 V VGS. The lower the number the faster the FETs must switch and the better the efficiency. 8.2.1.2.2.5 Rise and Fall Times A better indication of the actual switching times of the FETs can be found in their Electrical Characteristics table. The rise and fall time must be specified and selected to be at a minimum. This helps improve efficiency and ensuring that shoot-through does not occur. 8.2.1.2.2.6 Gate Charge Ratio Another consideration in selecting the FETs is to pay attention to the Qgd / Qgs ratio. The reason for this is that proper selection can prevent spurious turnon. If we look at the NFET for example, when the FET is turning off, the gate signal pulls to ground. Conversely the PFET is turning on, causing the SW node to rise towards VIN. The gate-to-drain capacitance of the NFET couples the SW node to the gate and causes it to rise. If this voltage is excessive, then it could weakly turn on the low-side FET causing an efficiency loss. However, this coupling is mitigated by having a large gate to source capacitance of the FET, which helps to hold the gate voltage down. Ideally, a very low Qgd / Qgs would be ideal, but in practice it is common to find the number around 1. As a general rule, the lower the ratio, the better. If the above selection criteria have been met it is useful to generate a figure of merit to allow comparison between the FETs. One such method is to multiply the RDS(ON) of the FET by the total gate charge. This allows an easy comparison of the different FETs available. Once again, the lower the product, the better. 8.2.1.2.2.7 Feedback Resistors The feedback resistors are used to scale the output voltage to the internal reference value such that the loop can be regulated. The feedback resistors must not be made arbitrarily large as this creates a high impedance node at the feedback pin that is more susceptible to noise. A combined value of 50 kΩ for the two resistors is adequate. To calculate the resistor values use Equation 16. Typically, the low-side resistor is initially set to a predetermined value such as 10 kΩ. § ¨ © RFB1 = RFB2 § VOUT -1 ¨ © VFB where • VFB is the internal reference voltage that can be found in the Electrical Characteristics table or approximated by 0.8 V (16) Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 17 LM1771 SNVS446D – JUNE 2006 – REVISED JANUARY 2016 www.ti.com The output voltage value can be set in a precise manner by taking into account the fact that the reference voltage is regulating the bottom of the output ripple as opposed to the average value. This relationship is shown in Figure 22. VOUT 'VOUT VOUT_ACTUAL VOUT_SET Figure 22. Output Voltage Waveform The average output voltage (VOUT_ACTUAL) is higher than the output voltage (VOUT_SET) that was calculated by the earlier equation by exactly half the output voltage ripple. The output voltage that is targeted for regulation may then be appended according to the voltage ripple. This can be seen in Equation 17: VOUT_ACTUAL= VOUT_SET + ½ΔVOUT = VOUT_SET + ½ΔIL x RESR (17) 8.2.1.2.3 Efficiency Calculations One of the most important parameters to calculate during the design stage is the expected efficiency of the system. This can help determine optimal FET selection and can be used to calculate expected temperature rise of the individual components. 8.2.1.2.3.1 Quiescent Current The quiescent current consumed by the LM1771 is one of the major sources of loss within the controller. However, from a system standpoint this is usually less than 0.5% of the overall efficiency. Therefore, it could easily be omitted but is shown for completeness: PIQ = VIN x IQ (18) 8.2.1.2.3.2 Conduction Loss There are three losses associated with the external FETs. From the DC standpoint there is the I-squared R loss, caused by the ON-resistance of the FET. This can be modeled for the PMOS by: PP_COND = D x RDSON_PMOS x IOUT2 (19) and the NMOS by: PN_COND = (1 - D) x RDSON_NMOS x IOUT2 (20) 8.2.1.2.3.3 Switching Loss The next loss is the switching loss that is caused by the need to charge and discharge the gate capacitance of the FETs every cycle. This can be approximated by: PP_SWITCH = VIN x Qg_PMOS x fSW (21) for the PMOS, and the same approach can be adapted for the NMOS: PN_SWITCH = VIN x Qg_NMOS x fSW (22) 8.2.1.2.3.4 Transitional Loss The last FET power loss is the transitional loss. This is caused by switching the PMOS while it is conducting current. This approach only models the PMOS transition, the NMOS loss is considered negligible because it has minimal drain to source voltage when it switches due to the conduction of the body diode. Therefore the transitional loss of the PMOS can be modeled by: PP_TRANSITIONAL = 0.5 x VIN x IOUT x fSW x (tr + tf) 18 Submit Documentation Feedback (23) Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 LM1771 www.ti.com SNVS446D – JUNE 2006 – REVISED JANUARY 2016 tr and tf are the rise and fall times of the FET and can be found in their corresponding datasheet. Typically these numbers are simulated using a 6-Ω drive, which corresponds well to the LM1771. Given this, no adjustment is needed. 8.2.1.2.3.5 DCR Loss The last source of power loss in the system that needs to be calculated is the loss associated with the inductor resistance (DCR) which can be calculated by Equation 24: PDCR = RDCR x IOUT2 (24) 8.2.1.2.3.6 Efficiency The efficiency, η, can then be calculated by summing all the power losses and then using Equation 25: K= POUT POUT + PLOSSES (25) 8.2.1.3 Application Curve Figure 23. Typical Efficiency 5 VIN to 2.5 VOUT 8.2.2 Example Application 5 VIN to 1.8 VOUT Figure 24 and Table 5 show an application with conversion from 5-V input to 1.8-V output with a switching frequency of 1.1 MHz and a 2-A maximum output current. VIN CIN VIN EN HG EN Q1 L1 LM1771 VOUT LG Q2 RSNS CFF RFB1 COUT FB RFB2 GND Figure 24. Example Circuit Schematic, 5 VIN to 1.8 VOUT Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 19 LM1771 SNVS446D – JUNE 2006 – REVISED JANUARY 2016 www.ti.com Table 5. Bill of Materials (5-V to 1.8-V Conversion, fSW = 1090 kHz, IOUT = 2 A) DESIGNATOR DESCRIPTION PART NUMBER QUANTITY VENDOR U1 LM1771, 500 ns LM1771S 1 Texas Instruments Q1 PMOS Si3867DV 1 Siliconix Q2 NMOS Si3460DV 1 Siliconix CIN 22-μF Capacitor, 0805 GRM21BR60J226ME39 1 Murata COUT 100-μF Capacitor, 6.3 V, 100 mΩ TPSY107M006R0100 1 AVX RFB1 12.4-kΩ Resistor, 0603 CRCW06031242F 1 Vishay RFB2 10-kΩ Resistor, 0603 CRCW06031002F 1 Vishay CFF 1-nF Capacitor, 0603 VJ0603102KXXA 1 Vishay 3.3-μH Inductor MSS7341-332NLB 1 Coilcraft L 8.2.3 Example Application 5 VIN to 3.3 VOUT Figure 25 and Table 6 show an application with conversion from 5-V input to 3.3-V output with a switching frequency of 500 kHz and a 5-A maximum output current. VIN CIN VIN EN Q1 HG EN L1 LM1771 VOUT Q2 LG RSNS CFF RFB1 COUT FB RFB2 GND Figure 25. Example Circuit Schematic, 5 VIN to 3.3 VOUT Table 6. Bill of Materials (5-V to 3.3-V Conversion, fSW = 500 kHz, IOUT = 5 A) DESIGNATOR DESCRIPTION PART NUMBER QUANTITY VENDOR U1 LM1771, 200 ns LM1771U 1 Texas Instruments Q1 PMOS Si9433BDY 1 Siliconix Q2 NMOS Si4894DY 1 Siliconix CIN 100-μF Capacitor, 1812 GRM43SR60J107ME20B 1 Murata COUT 150-μF Capacitor, 6.3 V, 70 mΩ NOSD157M006R0070 1 AVX RFB1 29.4-kΩ Resistor, 0805 CRCW08052942F 1 Vishay RFB2 10-kΩ Resistor, 0805 CRCW08051002F 1 Vishay CFF 1-nF Capacitor, 0805 VJ0805102KXXA 1 Vishay 2.2-μH Inductor DO3316P-222 1 Coilcraft L 9 Power Supply Recommendations The power line feeding the LM1771 must have low impedance. The input capacitor of the system must be placed as close to VIN as possible. If the power supply is very noisy, an additional bulk capacitor might be necessary in the system to ensure that clean power is delivered to the IC. 20 Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 LM1771 www.ti.com SNVS446D – JUNE 2006 – REVISED JANUARY 2016 10 Layout 10.1 Layout Guidelines The LM1771, like all switching regulators, requires careful attention to layout to ensure optimal performance. The following steps must be taken to aid in the layout. For more information refer to Application Note AN-1299 (SNVA074). 1. Ensure that the ground connections of the input capacitor, output capacitor and NMOS are as close as possible. Ideally these must all be grounded together in close proximity on the component side of the board. 2. Keep the switch node small to minimize EMI without degrading thermal cooling of the FETs. 3. Locate the feedback resistors close to the IC and keep the feedback trace as short as possible. Do not run any feedback traces near the switch node. 4. Keep the gate traces short and keep them away from the switch node as much as possible. 5. If a small bypass capacitor is used on VIN (0.1 µF) place it as close to the pin, with the ground connection as close to the chip ground, as possible. 10.2 Layout Examples CIN and COUT GND are close together Keep path of FET’s gate short Feedback components are close to the FB pin Limit surface of switch node to reduce capacitance Figure 26. LM1771 Layout Example (Top) Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 21 LM1771 SNVS446D – JUNE 2006 – REVISED JANUARY 2016 www.ti.com Layout Examples (continued) Figure 27. LM1771 Layout Example (Bottom) 10.3 Thermal Considerations By breaking down the individual power loss in each component it makes it easy to determine the temperature rise of each component. Generally the expected temperature rise of the LM1771 is extremely low as it is not in the power path. Therefore the only two items of concern are the PMOS and the NMOS. The power loss in the PMOS is the sum of the conduction loss and transitional loss, while the NMOS only has conduction loss. It is assumed that any loss associated with the body diode conduction during the dead-time is negligible. For completeness of design it is important to watch out for the temperature rise of the inductor. Assuming the inductor is kept out of saturation the predominant loss is the DC copper resistance. At higher frequencies, depending on the core material, the core loss could approach or exceed the DCR losses. Consult with the inductor manufacturer for appropriate temp curves based on current. 22 Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 LM1771 www.ti.com SNVS446D – JUNE 2006 – REVISED JANUARY 2016 11 Device and Documentation Support 11.1 Device Support 11.1.1 Third-Party Products Disclaimer TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE. 11.2 Documentation Support 11.2.1 Related Documentation For related documentation, see the following: User's Guide, AN-1299 LM5041 Evaluation Board, SNVA074 11.3 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 11.4 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. 11.5 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 11.6 Glossary SLYZ022 — TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. Submit Documentation Feedback Copyright © 2006–2016, Texas Instruments Incorporated Product Folder Links: LM1771 23 PACKAGE OPTION ADDENDUM www.ti.com 8-Oct-2015 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) LM1771SMM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LM1771SSD/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LM1771TMM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LM1771TSD/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LM1771UMM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LM1771USD/NOPB ACTIVE WSON NGG 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM Op Temp (°C) Device Marking (4/5) SNRB -40 to 125 1771S SNSB -40 to 125 1771T SNTB -40 to 125 1771U (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 8-Oct-2015 (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 24-Sep-2015 TAPE AND REEL INFORMATION *All dimensions are nominal Device LM1771SMM/NOPB Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM1771SSD/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LM1771TMM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM1771TSD/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LM1771UMM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM1771USD/NOPB WSON NGG 6 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 24-Sep-2015 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM1771SMM/NOPB LM1771SSD/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 WSON NGG 6 1000 210.0 185.0 35.0 LM1771TMM/NOPB LM1771TSD/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 WSON NGG 6 1000 210.0 185.0 35.0 LM1771UMM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 LM1771USD/NOPB WSON NGG 6 1000 210.0 185.0 35.0 Pack Materials-Page 2 MECHANICAL DATA NGG0006A SDE06A (Rev A) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2016, Texas Instruments Incorporated