[ /Title (CD54H C74, CD74H C74, CD74H CT74) /Subject (Dual D FlipFlop with Set CD54HC74, CD74HC74, CD54HCT74, CD74HCT74 Data sheet acquired from Harris Semiconductor SCHS124D Dual D Flip-Flop with Set and Reset Positive-Edge Trigger January 1998 - Revised September 2003 Features Description • Hysteresis on Clock Inputs for Improved Noise Immunity and Increased Input Rise and Fall Times The ’HC74 and ’HCT74 utilize silicon gate CMOS technology to achieve operating speeds equivalent to LSTTL parts. They exhibit the low power consumption of standard CMOS integrated circuits, together with the ability to drive 10 LSTTL loads. • Asynchronous Set and Reset • Complementary Outputs This flip-flop has independent DATA, SET, RESET and CLOCK inputs and Q and Q outputs. The logic level present at the data input is transferred to the output during the positive-going transition of the clock pulse. SET and RESET are independent of the clock and are accomplished by a low level at the appropriate input. • Buffered Inputs • Typical fMAX = 50MHz at VCC = 5V, CL = 15pF, TA = 25oC • Fanout (Over Temperature Range) - Standard Outputs . . . . . . . . . . . . . . . 10 LSTTL Loads - Bus Driver Outputs . . . . . . . . . . . . . 15 LSTTL Loads The HCT logic family is functionally as well as pin compatible with the standard LS logic family. • Wide Operating Temperature Range . . . -55oC to 125oC Ordering Information • Balanced Propagation Delay and Transition Times • Significant Power Reduction Compared to LSTTL Logic ICs PART NUMBER TEMP. RANGE (oC) PACKAGE • HC Types - 2V to 6V Operation - High Noise Immunity: NIL = 30%, NIH = 30% of VCC at VCC = 5V CD54HC74F3A -55 to 125 14 Ld CERDIP CD54HCT74F3A -55 to 125 14 Ld CERDIP CD74HC74E -55 to 125 14 Ld PDIP CD74HC74M -55 to 125 14 Ld SOIC • HCT Types - 4.5V to 5.5V Operation - Direct LSTTL Input Logic Compatibility, VIL= 0.8V (Max), VIH = 2V (Min) - CMOS Input Compatibility, Il ≤ 1µA at VOL, VOH CD74HC74MT -55 to 125 14 Ld SOIC CD74HC74M96 -55 to 125 14 Ld SOIC CD74HCT74E -55 to 125 14 Ld PDIP CD74HCT74M -55 to 125 14 Ld SOIC CD74HCT74MT -55 to 125 14 Ld SOIC CD74HCT74M96 -55 to 125 14 Ld SOIC NOTE: When ordering, use the entire part number. The suffix 96 denotes tape and reel. The suffix T denotes a small-quantity reel of 250. CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright © 2003, Texas Instruments Incorporated 1 CD54HC74, CD74HC74, CD54HCT74, CD74HCT74 Pinout CD54HC74, CD54HCT74 (CERDIP) CD74HC74, CD74HCT74 (PDIP, SOIC) TOP VIEW 1R 1 14 VCC 1D 2 13 2R 1CP 3 12 2D 1S 4 11 2CP 1Q 5 10 2S 1Q 6 9 2Q GND 7 8 2Q Functional Diagram 1 RESET R 2 DATA 5 Q D F/F 1 3 CLOCK 6 Q CP S 4 SET RESET 13 R 12 11 Q F/F 2 CP CLOCK S SET 9 D DATA 10 8 Q GND = PIN 7 VCC = PIN 14 TRUTH TABLE INPUTS OUTPUTS SET RESET CP D Q Q L H X X H L H L X X L H L L X X H (Note 1) H (Note 1) H H ↑ H H L H H ↑ L L H H H L X Q0 Q0 H= High Level (Steady State) L= Low Level (Steady State) X= Don’t Care ↑= Low-to-High Transition Q0 = the level of Q before the indicated input conditions were established. NOTE: 1. This configuration is nonstable, that is, it will not persist when set and reset inputs return to their inactive (high) level. 2 CD54HC74, CD74HC74, CD54HCT74, CD74HCT74 Absolute Maximum Ratings Thermal Information DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V DC Input Diode Current, IIK For VI < -0.5V or VI > VCC + 0.5V . . . . . . . . . . . . . . . . . . . . . .±20mA DC Drain Current, per Output, IO For -0.5V < VO < VCC + 0.5V. . . . . . . . . . . . . . . . . . . . . . . . . .±25mA DC Output Diode Current, IOK For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±20mA DC Output Source or Sink Current per Output Pin, IO For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±25mA DC VCC or Ground Current, ICC . . . . . . . . . . . . . . . . . . . . . . . . .±50mA Thermal Resistance (Typical, Note 2) θJA (oC/W) E (PDIP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 M (SOIC) Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Maximum Junction Temperature (Hermetic Package or Die) . . . 175oC Maximum Junction Temperature (Plastic Package) . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range (TA) . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Supply Voltage Range, VCC HC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 6V HCT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V DC Input or Output Voltage, VI, VO . . . . . . . . . . . . . . . . . 0V to VCC Input Rise and Fall Time 2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000ns (Max) 4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500ns (Max) 6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400ns (Max) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 2. The package thermal impedance is calculated in accordance with JESD 51-7. DC Electrical Specifications TEST CONDITIONS PARAMETER SYMBOL VI (V) VIH - 25oC IO (mA) VCC (V) -40oC TO 85oC -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS 2 1.5 - - 1.5 - 1.5 - V 4.5 3.15 - - 3.15 - 3.15 - V 6 4.2 - - 4.2 - 4.2 - V 2 - - 0.5 - 0.5 - 0.5 V 4.5 - - 1.35 - 1.35 - 1.35 V 6 - - 1.8 - 1.8 - 1.8 V HC TYPES High Level Input Voltage Low Level Input Voltage High Level Output Voltage CMOS Loads VIL VOH - VIH or VIL High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads Input Leakage Current II VCC or GND - - -0.02 2 1.9 - - 1.9 - 1.9 - V 4.5 4.4 - - 4.4 - 4.4 - V 6 5.9 - - 5.9 - 5.9 - V - - - - - - - - - V -4 4.5 3.98 - - 3.84 - 3.7 - V -5.2 6 5.48 - - 5.34 - 5.2 - V 0.02 2 - - 0.1 - 0.1 - 0.1 V 4.5 - - 0.1 - 0.1 - 0.1 V 6 - - 0.1 - 0.1 - 0.1 V - - - - - - - - - V 4 4.5 - - 0.26 - 0.33 - 0.4 V 5.2 6 - - 0.26 - 0.33 - 0.4 V - 6 - - ±0.1 - ±1 - ±1 µA 3 CD54HC74, CD74HC74, CD54HCT74, CD74HCT74 DC Electrical Specifications (Continued) TEST CONDITIONS SYMBOL VI (V) ICC VCC or GND 0 High Level Input Voltage VIH - Low Level Input Voltage VIL High Level Output Voltage CMOS Loads VOH PARAMETER Quiescent Device Current 25oC IO (mA) VCC (V) -40oC TO 85oC -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS 6 - - 4 - 40 - 80 µA - 4.5 to 5.5 2 - - 2 - 2 - V - - 4.5 to 5.5 - - 0.8 - 0.8 - 0.8 V VIH or VIL -0.02 4.5 4.4 - - 4.4 - 4.4 - V -4 4.5 3.98 - - 3.84 - 3.7 - V 0.02 4.5 - - 0.1 - 0.1 - 0.1 V 4 4.5 - - 0.26 - 0.33 - 0.4 V ±0.1 - ±1 - ±1 µA HCT TYPES High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads Input Leakage Current Quiescent Device Current Additional Quiescent Device Current Per Input Pin: 1 Unit Load II VCC and GND - 5.5 - ICC VCC or GND 0 5.5 - - 4 - 40 - 80 µA ∆ICC (Note 3) VCC - 2.1 - 4.5 to 5.5 - 100 360 - 450 - 490 µA NOTE: 3. For dual-supply systems theoretical worst case (VI = 2.4V, VCC = 5.5V) specification is 1.8mA. HCT Input Loading Table INPUT UNIT LOADS D 0.5 R 0.5 CP 0.7 S 0.75 NOTE: Unit Load is ∆ICC limit specified in DC Electrical Specifications table, e.g., 360µA max at 25oC. Prerequisite For Switching Specifications PARAMETER 25oC -40oC TO 85oC -55oC TO 125oC SYMBOL TEST CONDITIONS VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS tSU - 2 60 - - 75 - 90 - ns 4.5 12 - - 15 - 18 - ns 6 10 - - 13 - 15 - ns HC TYPES Data to CP Setup Time (Figure 5) 4 CD54HC74, CD74HC74, CD54HCT74, CD74HCT74 Prerequisite For Switching Specifications PARAMETER Hold Time (Figure 5) -40oC TO 85oC -55oC TO 125oC SYMBOL VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS tH - 2 3 - - 3 - 3 - ns 4.5 3 - - 3 - 3 - ns 6 3 - - 3 - 3 - ns 2 30 - - 40 - 45 - ns 4.5 6 - - 8 - 9 - ns tREM Pulse Width R, S (Figure 1) tW CP Frequency 25oC TEST CONDITIONS Removal Time R, S, to CP (Figure 5) Pulse Width CP (Figure 1) (Continued) - - tW - fMAX - 6 5 - - 7 - 8 - ns 2 80 - - 100 - 120 - ns 4.5 16 - - 20 - 24 - ns 6 14 - - 17 - 20 - ns 2 80 - - 100 - 120 - ns 4.5 16 - - 20 - 24 - ns 6 14 - - 17 - 20 - ns 2 6 - - 5 - 4 - MHz 4.5 30 - - 25 - 20 - MHz 6 35 - - 29 - 23 - MHz HCT TYPES Data to CP Setup Time (Figure 6) tSU - 4.5 12 - - 15 - 18 - ns tH - 4.5 3 - - 3 - 3 - ns Removal Time R, S, to CP (Figure 6) tREM - 4.5 6 - - 8 - 9 - ns Pulse Width R, S (Figure 2) tW - 4.5 16 - - 20 - 24 - ns Pulse Width CP (Figure 2) tW - 4.5 18 - - 23 - 27 - ns fMAX - 4.5 25 - - 20 - 16 - MHz SYMBOL TEST CONDITIONS VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS tPLH, tPHL CL = 50pF 2 - - 175 - 220 - 265 ns CL = 50pF 4.5 - - 35 - 44 - 53 ns CL = 15pF 5 - 14 - - - - - ns CL = 50pF 6 - - 30 - 37 - 45 ns Hold Time (Figure 6) CP Frequency Switching Specifications Input tr, tf = 6ns PARAMETER 25oC -40oC TO 85oC -55oC TO 125oC HC TYPES Propagation Delay, CP to Q, Q (Figure 3) Propagation Delay, R, S to Q, Q (Figure 3) Transition Time (Figure 3) Input Capacitance tPLH, tPHL tTLH, tTHL CI CL = 50pF 2 - - 200 - 250 - 300 ns CL = 50pF 4.5 - - 40 - 50 - 60 ns CL = 15pF 5 - 17 - - - - - ns CL = 50pF 6 - - 34 - 43 - 51 ns CL = 50pF 2 - - 75 - 95 - 110 ns CL = 50pF 4.5 - - 15 - 19 - 22 ns CL = 50pF 6 - - 13 - 16 - 19 ns - - - 10 - 10 - 10 pF - 5 CD54HC74, CD74HC74, CD54HCT74, CD74HCT74 Switching Specifications Input tr, tf = 6ns (Continued) 25oC -40oC TO 85oC -55oC TO 125oC SYMBOL TEST CONDITIONS VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS CP Frequency fMAX CL = 15pF 5 - 50 - - - - - MHz Power Dissipation Capacitance (Notes 4, 5) CPD - 5 - 25 - - - - - pF PARAMETER HCT TYPES Propagation Delay, CP to Q, Q (Figure 4) tPLH, tPHL CL = 50pF 4.5 - - 35 - 44 - 53 ns Propagation Delay, R, S to Q, Q (Figure 4) tPHL, tPLH CL = 50pF 4.5 - - 40 - 50 - 60 ns Transition Time (Figure 4) tTLH, tTHL CL = 50pF 4.5 - - 15 - 19 - 22 ns Input Capacitance CI - - - - 10 - 10 - 10 pF CP Frequency fMAX CL = 15pF 5 - 50 - - - - - MHz Power Dissipation Capacitance (Notes 4, 5) CPD - 5 - 30 - - - - - pF NOTES: 4. CPD is used to determine the dynamic power consumption, per flip-flop. 5. PD = CPD VCC2 fi + Σ (CL VCC2 fo) where fi = input frequency, fo = output frequency, CL = output load capacitance, VCC = supply voltage. Test Circuits and Waveforms tfCL trCL CLOCK tWL + tWH = 90% 10% I tr = 6ns tf = 6ns tr = 6ns GND tTLH 3V 2.7V 1.3V 0.3V INPUT GND tTHL 90% 50% 10% INVERTING OUTPUT tWH FIGURE 2. HCT CLOCK PULSE RISE AND FALL TIMES AND PULSE WIDTH VCC tTHL GND NOTE: Outputs should be switching from 10% VCC to 90% VCC in accordance with device truth table. For fMAX, input duty cycle = 50%. tf = 6ns 90% 50% 10% 1.3V 1.3V tWL FIGURE 1. HC CLOCK PULSE RISE AND FALL TIMES AND PULSE WIDTH tPHL 1.3V 0.3V tWH NOTE: Outputs should be switching from 10% VCC to 90% VCC in accordance with device truth table. For fMAX, input duty cycle = 50%. INPUT 2.7V 0.3V GND tWL I fCL 3V CLOCK 50% 50% tfCL = 6ns fCL VCC 50% 10% tWL + tWH = trCL = 6ns tTLH 90% 1.3V 10% INVERTING OUTPUT tPHL tPLH FIGURE 3. HC AND HCU TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC tPLH FIGURE 4. HCT TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC 6 CD54HC74, CD74HC74, CD54HCT74, CD74HCT74 Test Circuits and Waveforms trCL tfCL trCL CLOCK INPUT (Continued) VCC 90% GND tH(H) GND tH(H) VCC DATA INPUT 50% tH(L) 3V 1.3V 1.3V 1.3V GND tSU(H) tSU(H) tSU(L) tTLH 90% OUTPUT tTHL 90% 50% 10% tTLH 90% 1.3V OUTPUT tREM 3V SET, RESET OR PRESET GND tTHL 1.3V 10% FIGURE 5. HC SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS tPHL 1.3V GND IC CL 50pF GND 90% tPLH 50% IC tSU(L) tPHL tPLH tREM VCC SET, RESET OR PRESET 1.3V 0.3V tH(L) DATA INPUT 3V 2.7V CLOCK INPUT 50% 10% tfCL CL 50pF FIGURE 6. HCT SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS 7 PACKAGE OPTION ADDENDUM www.ti.com 28-Feb-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty 5962-8685301CA ACTIVE CDIP J 14 1 None Call TI Level-NC-NC-NC CD54HC74F ACTIVE CDIP J 14 1 None Call TI Level-NC-NC-NC CD54HC74F3A ACTIVE CDIP J 14 1 None Call TI Level-NC-NC-NC CD54HCT74F ACTIVE CDIP J 14 1 None Call TI Level-NC-NC-NC CD54HCT74F3A ACTIVE CDIP J 14 1 None Call TI Level-NC-NC-NC CD74HC74E ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC CD74HC74M ACTIVE SOIC D 14 50 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM CD74HC74M96 ACTIVE SOIC D 14 2500 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM CD74HC74MT ACTIVE SOIC D 14 250 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM CD74HCT74E ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC CD74HCT74M ACTIVE SOIC D 14 50 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM CD74HCT74M96 ACTIVE SOIC D 14 2500 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM CD74HCT74MT ACTIVE SOIC D 14 250 Pb-Free (RoHS) CU NIPDAU Level-2-260C-1 YEAR/ Level-1-235C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. None: Not yet available Lead (Pb-Free). Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens, including bromine (Br) or antimony (Sb) above 0.1% of total product weight. (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated