LM368-10,LM368-5.0 LM368-5.0 and LM368-10 Precision Voltage References Literature Number: SNVS744A LM368-5.0 and LM368-10 Precision Voltage References General Description Features The LM368 is a precision, monolithic, temperature-compensated voltage reference. The LM368 makes use of thin-film technology enhanced by the discrete laser trimming of resistors to achieve excellent Temperature coefficient (Tempco) of VOUT (as low as 5ppm/§ C), along with tight initial tolerance, (as low as 0.02%). The trim scheme is such that individual resistors are cut open rather than being trimmed (partially cut), to avoid resistor drift caused by electromigration in the trimmed area. The LM368 also provides excellent stability vs. changes in input voltage and output current (both sourcing and sinking). This device is available in output voltage options of 5.0V and 10.0V and will operate in both series or shunt mode. Also see the LM368-2.5 data sheet for a 2.5V output. The devices are short circuit proof when sourcing current. A trim pin is made available for fine trimming of VOUT or for obtaining intermediate values without greatly affecting the Tempco of the device. Y Y Y Y Y Y Y et Y 300 mA operating current Low output impedance Excellent line regulation (.0001%/V typical) Single-supply operation Externally trimmable Low temperature coefficient Operates in series or shunt mode 10.0V or 5.0V Excellent initial accuracy (0.02% typical) e Y Connection Diagram bs ol Metal Can Package TL/H/5522 – 1 Top View *case connected to Vb Order Number LM368YH-10, LM368YH-5.0, LM368H-10, LM368H-5.0 See NS Package Number H08C O Typical Applications Series Regulator Shunt Regulator TL/H/5522– 2 TL/H/5522 – 3 C1995 National Semiconductor Corporation TL/H/5522 RRD-B30M115/Printed in U. S. A. LM368-5.0 and LM368-10 Precision Voltage References January 1995 Absolute Maximum Ratings (Note 8) Input Voltage (Series Mode) Power Dissipation Storage Temperature Range Operating Temperature Range LM368 Soldering Information TO-5 (H) Package, 10 sec. 35V Reverse Current (Shunt Mode) 50 mA a 300§ C See AN-450 ‘‘Surface Mounting Methods and Their Effect on Product Reliability’’ (Appendix D) for other methods of soldering surface mount devices. 600 mW b 60§ C to a 150§ C 0§ C to a 70§ C Electrical Characteristics (Note 1) LM368 Parameter Conditions Tested Limit (Note 2) Design Limit (Note 3) Units (Max. unless noted) g 0.02 g 0.1 % Line Regulation (VOUT a 3V) s VIN s 30V g 0.0001 g 0.0005 %/V Load Regulation (Note 4) 0 mA s ISOURCE s 10 mA b 10 mA s ISINK s 0 mA g 0.0003 g 0.001 g 0.003 g 0.008 %/mA %/mA Thermal Regulation T e 20 mS (Note 5) g 0.005 Quiescent Current 250 (VOUT a 3V) s VIN s 30V Temperature Coefficient of VOUT (see graph): LM368Y (Note 6) LM368 0§ C s TA s 70§ C 0§ C s TA s 70§ C Short Circuit Current VOUT e 0 10.0V: 0.1 - 10Hz 100Hz - 10 kHz 6.2V: 0.1 - 10Hz 100Hz - 10 kHz 5.0V: 0.1 - 10Hz 100Hz - 10 kHz %/100 mW 350 mA 5 mA/V g 11 g 20 g 15 30 70 g 30 ppm/§ C ppm/§ C 100 mA 30 1100 20 700 16 575 bs ol Noise: 3 g 0.01 et Change of Quiescent Current vs. VIN e VOUT Error Typical VOUT Adjust Range: 10.000V 5.000V 0V s VPIN5 s VOUT 4.5-17.0 4.4-7.0 6.0-15.5 4.5-6.0 uVp-p nV/0Hz uVp-p nV/0Hz uVp-p nV/0Hz V min. V min. Note 1: Unless otherwise noted, these specifications apply: TA e 25§ C, VIN e 15V, ILOAD e 0, 0 s CL s 200 pF, Circuit is operating in Series Mode. Or, circuit is operating in Shunt Mode, VIN e a 15V or VIN e VOUT, TA e a 25§ C, ILOAD e b 1.0 mA, 0 s CL s 200 pF. Note 2: Tested Limits are guaranteed and 100% tested in production. Note 3: Design Limits are guaranteed (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are not used to calculate outgoing quality levels. Note 4: The LM368 has a Class B output, and will exhibit transients at the crossover point. This point occurs when the device is asked to sink approximately 120 mA. In some applications it may be advantageous to preload the output to either VIN or Ground, to avoid this crossover point. Note 5: Thermal Regulation is defined as the change in the output Voltage at a time T after a step change in power dissipation of 100 mW. O Note 6: Temperature Coefficient of VOUT is defined as the worst case delta-VOUT measured at Specified Temperatures divided by the total span of the Specified Temperature Range (See graphs). There is no guarantee that the Specified Temperatures are exactly at the minimum or maximum deviation. Note 7: In metal can (H), iJ–C is 75§ C/W and iJ–A is 150§ C/W. Note 8: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its Rated Operating Conditions (see Note 1 and Conditions). 2 Typical Performance Characteristics (Note 1) Dropout Voltage vs. Output Current (Series Mode Sourcing Current) Output Change vs. Output Current Output Impedance vs. Frequency (Sourcing Current) Ripple Rejection vs. Frequency Output Impedance vs. Frequency (Sinking Current) et e Quiescent Current vs. Input Voltage and Temperature bs ol Temperature Coefficient: LM368-10 (Curve A) Typical Temperature Coefficient Calculations: LM368-10 (see Curve A) O T.C. e 7.7 mV/(70§ c 10V) e 11 c 10E-6 e 11ppm/§ C Output Noise vs. Frequency (1) LM368 alone. (2) with 0.01 mf Mylar, Trim to Gnd. (3) with 10X in series with 10 mf, VOUT to Gnd. (4) with Both. TL/H/5522 – 5 3 TL/H/5522 – 4 Typical Applications Wide Range Trimmable Regulator Narrow Range Trimmable Regulator ( g 1% min.) TL/H/5522–7 TL/H/5522 – 8 Improved Noise Performance e Adjustable Zener et TL/H/5522 – 10 g 10V, g 5V References bs ol TL/H/5522–9 O g Reference e (/4 LF444A or (/2 LF412A TL/H/5522 – 12 Re TL/H/5522–11 4 Thin Film Resistor Network, g 0.05% Matching and 5ppm Tracking (Beckman 694-3-R-10K-A), (Caddock T-914-10K-100-05) or similar. Typical Applications (Continued) Multiple Output Voltages TL/H/5522 – 14 et e TL/H/5522 – 13 Thin Film Resistor Network 0.05% Matching and 5ppm Tracking (Beckman 694-3-R-10K-A), (Caddock T-914-10K-100-05) or similar. bs ol Re TL/H/5522 – 15 100 mA Boosted Reference O Reference with Booster TL/H/5522 – 16 TL/H/5522 – 17 5 Typical Applications (Continued) e Buffered High-Current Reference with Filter O bs ol Simplified Schematic Diagram et TL/H/5522 – 18 TL/H/5522 – 6 *Reg. U.S. Pat. Off. 6 7 e et bs ol O e et bs ol LM368-5.0 and LM368-10 Precision Voltage References Physical Dimensions inches (millimeters) Thermal resistance is 45§ C/W, junction to case, and 150§ C/W, junction to still air. Metal Can Package (H) Order Number LM368YH-10, LM368YH-5.0, LM368H-10, LM368H-5.0 NS Package Number H08C LIFE SUPPORT POLICY O NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation 1111 West Bardin Road Arlington, TX 76017 Tel: 1(800) 272-9959 Fax: 1(800) 737-7018 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Europe Fax: (a49) 0-180-530 85 86 Email: cnjwge @ tevm2.nsc.com Deutsch Tel: (a49) 0-180-530 85 85 English Tel: (a49) 0-180-532 78 32 Fran3ais Tel: (a49) 0-180-532 93 58 Italiano Tel: (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Centre, 5 Canton Rd. Tsimshatsui, Kowloon Hong Kong Tel: (852) 2737-1600 Fax: (852) 2736-9960 National Semiconductor Japan Ltd. Tel: 81-043-299-2309 Fax: 81-043-299-2408 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated