Kemet C114G1402G5C Multilayer ceramic capacitors/axial & radial leaded Datasheet

MULTILAYER CERAMIC CAPACITORS/AXIAL
& RADIAL LEADED
Multilayer ceramic capacitors are available in a
variety of physical sizes and configurations, including
leaded devices and surface mounted chips. Leaded
styles include molded and conformally coated parts
with axial and radial leads. However, the basic
capacitor element is similar for all styles. It is called a
chip and consists of formulated dielectric materials
which have been cast into thin layers, interspersed
with metal electrodes alternately exposed on opposite
edges of the laminated structure. The entire structure is
fired at high temperature to produce a monolithic
block which provides high capacitance values in a
small physical volume. After firing, conductive
terminations are applied to opposite ends of the chip to
make contact with the exposed electrodes.
Termination materials and methods vary depending on
the intended use.
TEMPERATURE CHARACTERISTICS
Ceramic dielectric materials can be formulated with
Class III: General purpose capacitors, suitable
a wide range of characteristics. The EIA standard for
for by-pass coupling or other applications in which
ceramic dielectric capacitors (RS-198) divides ceramic
dielectric losses, high insulation resistance and
dielectrics into the following classes:
stability of capacitance characteristics are of little or
no importance. Class III capacitors are similar to Class
Class I: Temperature compensating capacitors,
II capacitors except for temperature characteristics,
suitable for resonant circuit application or other appliwhich are greater than ± 15%. Class III capacitors
cations where high Q and stability of capacitance charhave the highest volumetric efficiency and poorest
acteristics are required. Class I capacitors have
stability of any type.
predictable temperature coefficients and are not
affected by voltage, frequency or time. They are made
KEMET leaded ceramic capacitors are offered in
from materials which are not ferro-electric, yielding
the three most popular temperature characteristics:
superior stability but low volumetric efficiency. Class I
C0G: Class I, with a temperature coefficient of 0 ±
capacitors are the most stable type available, but have
30 ppm per degree C over an operating
the lowest volumetric efficiency.
temperature range of - 55°C to + 125°C (Also
known as “NP0”).
Class II: Stable capacitors, suitable for bypass
X7R: Class II, with a maximum capacitance
or coupling applications or frequency discriminating
change of ± 15% over an operating temperature
circuits where Q and stability of capacitance charrange of - 55°C to + 125°C.
acteristics are not of major importance. Class II
Z5U: Class III, with a maximum capacitance
capacitors have temperature characteristics of ± 15%
change of + 22% - 56% over an operating temor less. They are made from materials which are
perature range of + 10°C to + 85°C.
ferro-electric, yielding higher volumetric efficiency but
less stability. Class II capacitors are affected by
Specified electrical limits for these three temperature
temperature, voltage, frequency and time.
characteristics are shown in Table 1.
SPECIFIED ELECTRICAL LIMITS
Temperature Characteristics
Parameter
Dissipation Factor: Measured at following conditions.
C0G – 1 kHz and 1 vrms if capacitance >1000pF
1 MHz and 1 vrms if capacitance 1000 pF
X7R – 1 kHz and 1 vrms* or if extended cap range 0.5 vrms
Z5U – 1 kHz and 0.5 vrms
C0G
X7R
Z5U
0.10%
2.5%
(3.5% @ 25V)
4.0%
Dielectric Stength: 2.5 times rated DC voltage.
Pass Subsequent IR Test
Insulation Resistance (IR): At rated DC voltage,
whichever of the two is smaller
1,000 M
F
or 100 G
1,000 M
F
or 100 G
Temperature Characteristics: Range, °C
Capacitance Change without
DC voltage
-55 to +125
0 ± 30 ppm/°C
-55 to +125
± 15%
* MHz and 1 vrms if capacitance
1,000 M
or 10 G
100 pF on military product.
Table I
4
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
F
+ 10 to +85
+22%,-56%
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
Polarity: Multilayer ceramic capacitors are not polar,
and may be used with DC voltage applied in either direction.
Rated Voltage: This term refers to the maximum continuous DC working voltage permissible across the entire
operating temperature range. Multilayer ceramic capacitors
are not extremely sensitive to voltage, and brief applications
of voltage above rated will not result in immediate failure.
However, reliability will be reduced by exposure to sustained
voltages above rated.
Capacitance: The standard unit of capacitance is the
farad. For practical capacitors, it is usually expressed in
microfarads (10-6 farad), nanofarads (10-9 farad), or picofarads
(10-12 farad). Standard measurement conditions are as
follows:
Class I (up to 1,000 pF):
1MHz and 1.2 VRMS
maximum.
Class I (over 1,000 pF):
1kHz and 1.2 VRMS
maximum.
Class II:
1 kHz and 1.0 ± 0.2 VRMS.
Class III:
1 kHz and 0.5 ± 0.1 VRMS.
Like all other practical capacitors, multilayer ceramic
capacitors also have resistance and inductance. A simplified
schematic for the equivalent circuit is shown in Figure 1.
Other significant electrical characteristics resulting from
these additional properties are as follows:
R
P
Figure 1
R
S
L
C
C = Capacitance
L = Inductance
R = Equivalent Series Resistance (ESR)
S
R = Insulation Resistance (IR)
P
Impedance: Since the parallel resistance (Rp) is normally very high, the total impedance of the capacitor is:
Z=
Where
2
RS + (XC - XL)
2
Z = Total Impedance
RS = Equivalent Series Resistance
XC = Capacitive Reactance =
1
2π
πfC
XL = Inductive Reactance = 2π
πfL
The variation of a capacitor’s impedance with frequency
determines its effectiveness in many applications.
Application Notes
ELECTRICAL CHARACTERISTICS
The fundamental electrical properties of multilayer
ceramic capacitors are as follows:
Dissipation Factor: Dissipation Factor (DF) is a measure of the losses in a capacitor under AC application. It is the
ratio of the equivalent series resistance to the capacitive reactance, and is usually expressed in percent. It is usually measured simultaneously with capacitance, and under the same
conditions. The vector diagram in Figure 2 illustrates the relationship between DF, ESR, and impedance. The reciprocal of
the dissipation factor is called the “Q”, or quality factor. For
convenience, the “Q” factor is often used for very low values
of dissipation factor. DF is sometimes called the “loss tangent”
or “tangent d”, as derived from this diagram.
ESR
Figure 2
O
DF = ESR
Xc
δ
X
c
Ζ
1
Xc =
2πfC
Insulation Resistance: Insulation Resistance (IR) is the
DC resistance measured across the terminals of a capacitor,
represented by the parallel resistance (Rp) shown in Figure 1.
For a given dielectric type, electrode area increases with
capacitance, resulting in a decrease in the insulation resistance. Consequently, insulation resistance is usually specified
as the “RC” (IR x C) product, in terms of ohm-farads or
megohm-microfarads. The insulation resistance for a specific
capacitance value is determined by dividing this product by
the capacitance. However, as the nominal capacitance values
become small, the insulation resistance calculated from the
RC product reaches values which are impractical.
Consequently, IR specifications usually include both a minimum RC product and a maximum limit on the IR calculated
from that value. For example, a typical IR specification might
read “1,000 megohm-microfarads or 100 gigohms, whichever
is less.”
Insulation Resistance is the measure of a capacitor to
resist the flow of DC leakage current. It is sometimes referred
to as “leakage resistance.” The DC leakage current may be
calculated by dividing the applied voltage by the insulation
resistance (Ohm’s Law).
Dielectric Withstanding Voltage: Dielectric withstanding voltage (DWV) is the peak voltage which a capacitor is
designed to withstand for short periods of time without damage. All KEMET multilayer ceramic capacitors will withstand a
test voltage of 2.5 x the rated voltage for 60 seconds.
KEMET specification limits for these characteristics at
standard measurement conditions are shown in Table 1 on
page 4. Variations in these properties caused by changing
conditions of temperature, voltage, frequency, and time are
covered in the following sections.
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
5
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
TABLE 1
EIA TEMPERATURE CHARACTERISTIC CODES
FOR CLASS I DIELECTRICS
Significant Figure
of Temperature
Coefficient
Multiplier Applied
to Temperature
Coefficient
Tolerance of
Temperature
Coefficient *
PPM per
Degree C
Letter
Symbol
Multiplier
Number
Symbol
PPM per
Degree C
Letter
Symbol
0.0
0.3
0.9
1.0
1.5
2.2
3.3
4.7
7.5
C
B
A
M
P
R
S
T
U
-1
-10
-100
-1000
-100000
+1
+10
+100
+1000
+10000
0
1
2
3
4
5
6
7
8
9
±30
±60
±120
±250
±500
±1000
±2500
G
H
J
K
L
M
N
* These symetrical tolerances apply to a two-point measurement of
temperature coefficient: one at 25°C and one at 85°C. Some deviation
is permitted at lower temperatures. For example, the PPM tolerance
for C0G at -55°C is +30 / -72 PPM.
TABLE 2
EIA TEMPERATURE CHARACTERISTIC CODES
FOR CLASS II & III DIELECTRICS
6
Low Temperature
Rating
High Temperature Maximum Capacitance
Rating
Shift
Degree
Celcius
Letter
Symbol
Degree
Celcius
Number
Symbol
+10C
-30C
-55C
Z
Y
X
+45C
+65C
+85C
+105C
+125C
+150C
+200C
2
4
5
6
7
8
9
Percent
±1.0%
±1.5%
±2.2%
±3.3%
±4.7%
±7.5%
±10.0%
±15.0%
±22.0%
+22 / -33%
+22 / -56%
+22 / -82%
Letter
Symbol
A
B
C
D
E
F
P
R
S
T
U
V
+10
+20
+30
+40
+50
+60
+70
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
+80
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
Application Notes
At higher AC voltages, both capacitance and dissipation factor
begin to decrease.
Typical curves showing the effect of applied AC and DC
voltage are shown in Figure 6 for KEMET X7R capacitors and
Figure 7 for KEMET Z5U capacitors.
Effect of Frequency: Frequency affects both capacitance and dissipation factor. Typical curves for KEMET multilayer ceramic capacitors are shown in Figures 8 and 9.
The variation of impedance with frequency is an important consideration in the application of multilayer ceramic
capacitors. Total impedance of the capacitor is the vector of the
capacitive reactance, the inductive reactance, and the ESR, as
illustrated in Figure 2. As frequency increases, the capacitive
reactance decreases. However, the series inductance (L)
shown in Figure 1 produces inductive reactance, which
increases with frequency. At some frequency, the impedance
ceases to be capacitive and becomes inductive. This point, at
the bottom of the V-shaped impedance versus frequency
curves, is the self-resonant frequency. At the self-resonant frequency, the reactance is zero, and the impedance consists of
the ESR only.
Typical impedance versus frequency curves for KEMET
multilayer ceramic capacitors are shown in Figures 10, 11, and
12. These curves apply to KEMET capacitors in chip form, without leads. Lead configuration and lead length have a significant
impact on the series inductance. The lead inductance is
approximately 10nH/inch, which is large compared to the
inductance of the chip. The effect of this additional inductance
is a decrease in the self-resonant frequency, and an increase
in impedance in the inductive region above the self-resonant
frequency.
Effect of Time: The capacitance of Class II and III
dielectrics change with time as well as with temperature, voltage and frequency. This change with time is known as “aging.”
It is caused by gradual realignment of the crystalline structure
of the ceramic dielectric material as it is cooled below its Curie
temperature, which produces a loss of capacitance with time.
The aging process is predictable and follows a logarithmic
decay. Typical aging rates for C0G, X7R, and Z5U dielectrics
are as follows:
C0G
X7R
Z5U
Effect of Temperature: Both capacitance and dissipation factor are affected by variations in temperature. The maximum capacitance change with temperature is defined by the
temperature characteristic. However, this only defines a “box”
bounded by the upper and lower operating temperatures and
the minimum and maximum capacitance values. Within this
“box”, the variation with temperature depends upon the specific dielectric formulation. Typical curves for KEMET capacitors are shown in Figures 3, 4, and 5. These figures also
include the typical change in dissipation factor for KEMET
capacitors.
Insulation resistance decreases with temperature.
Typically, the insulation resistance at maximum rated temperature is 10% of the 25°C value.
Effect of Voltage: Class I ceramic capacitors are not
affected by variations in applied AC or DC voltages. For Class
II and III ceramic capacitors, variations in voltage affect only
the capacitance and dissipation factor. The application of DC
voltage higher than 5 vdc reduces both the capacitance and
dissipation factor. The application of AC voltages up to 10-20
Vac tends to increase both capacitance and dissipation factor.
None
2.0% per decade of time
5.0% per decade of time
Typical aging curves for X7R and Z5U dielectrics are
shown in Figure 13.
The aging process is reversible. If the capacitor is heated to a temperature above its Curie point for some period of
time, de-aging will occur and the capacitor will regain the
capacitance lost during the aging process. The amount of deaging depends on both the elevated temperature and the
length of time at that temperature. Exposure to 150°C for onehalf hour or 125°C for two hours is usually sufficient to return
the capacitor to its initial value.
Because the capacitance changes rapidly immediately
after de-aging, capacitance measurements are usually delayed
for at least 10 hours after the de-aging process, which is often
referred to as the “last heat.” In addition, manufacturers utilize
the aging rates to set factory test limits which will bring the
capacitance within the specified tolerance at some future time,
to allow for customer receipt and use. Typically, the test limits
are adjusted so that the capacitance will be within the specified
tolerance after either 1,000 hours or 100 days, depending on
the manufacturer and the product type.
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
7
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
POWER DISSIPATION
Power dissipation has been empirically determined for
two representative KEMET series: C052 and C062. Power dissipation capability for various mounting configurations is shown
in Table 3. This table was extracted from Engineering Bulletin
F-2013, which provides a more detailed treatment of this subject.
Note that no significant difference was detected between
the two sizes in spite of a 2 to 1 surface area ratio. Due to the
materials used in the construction of multilayer ceramic capacitors, the power dissipation capability does not depend greatly
on the surface area of the capacitor body, but rather on how
well heat is conducted out of the capacitor lead wires.
Consequently, this power dissipation capability is applicable to
other leaded multilayer styles and sizes.
TABLE 3
POWER DISSIPATION CAPABILITY
(Rise in Celsius degrees per Watt)
Mounting Configuration
Power
Dissipation
of C052 & C062
1.00" leadwires attached to binding post
of GR-1615 bridge (excellent heat sink)
90 Celsius degrees
rise per Watt ±10%
0.25" leadwires attached to binding post
of GR-1615 bridge
55 Celsius degrees
rise per Watt ±10%
Capacitor mounted flush to 0.062" glassepoxy circuit board with small copper traces
77 Celsius degrees
rise per Watt ±10%
Capacitor mounted flush to 0.062" glassepoxy circuit board with four square inches
of copper land area as a heat sink
53 Celsius degrees
rise per Watt ±10%
As shown in Table 3, the power dissipation capability of
the capacitor is very sensitive to the details of its use environment. The temperature rise due to power dissipation should not
exceed 20°C. Using that constraint, the maximum permissible
power dissipation may be calculated from the data provided in
Table 3.
It is often convenient to translate power dissipation capability into a permissible AC voltage rating. Assuming a sinusoidal wave form, the RMS “ripple voltage” may be calculated
from the following formula:
E=Zx
Where
PMAX
R
RELIABILITY
A well constructed multilayer ceramic capacitor is
extremely reliable and, for all practical purposes, has an infinite life span when used within the maximum voltage and
temperature ratings. Capacitor failure may be induced by sustained operation at voltages that exceed the rated DC voltage,
voltage spikes or transients that exceed the dielectric withstanding voltage, sustained operation at temperatures above
the maximum rated temperature, or the excessive temperature rise due to power dissipation.
Failure rate is usually expressed in terms of percent per
1,000 hours or in FITS (failure per billion hours). Some
KEMET series are qualified under U.S. military established
reliability specifications MIL-PRF-20, MIL-PRF-123, MILPRF-39014, and MIL-PRF-55681. Failure rates as low as
0.001% per 1,000 hours are available for all capacitance /
voltage ratings covered by these specifications. These specifications and accompanying Qualified Products List should
be consulted for details.
For series not covered by these military specifications,
an internal testing program is maintained by KEMET Quality
Assurance. Samples from each week’s production are subjected to a 2,000 hour accelerated life test at 2 x rated voltage
and maximum rated temperature. Based on the results of
these tests, the average failure rate for all non-military series
covered by this test program is currently 0.06% per 1,000
hours at maximum rated conditions. The failure rate would be
much lower at typical use conditions. For example, using MILHDBK-217D this failure rate translates to 0.9 FITS at 50%
rated voltage and 50°C.
Current failure rate details for specific KEMET multilayer ceramic capacitor series are available on request.
MISAPPLICATION
Ceramic capacitors, like any other capacitors, may fail
if they are misapplied. Typical misapplications include exposure to excessive voltage, current or temperature. If the
dielectric layer of the capacitor is damaged by misapplication
the electrical energy of the circuit can be released as heat,
which may damage the circuit board and other components
as well.
If potential for misapplication exists, it is recommended
that precautions be taken to protect personnel and equipment
during initial application of voltage. Commonly used precautions include shielding of personnel and sensing for excessive
power drain during board testing.
E = RMS Ripple Voltage (volts)
P = Power Dissipation (watts)
Z = Impedance
R = ESR
The data necessary to make this calculation is included in
Engineering Bulletin F-2013. However, the following criteria
must be observed:
1. The temperature rise due to power dissipation
should be limited to 20°C.
2. The peak AC voltage plus the DC voltage must not
exceed the maximum working voltage of the
capacitor.
Provided that these criteria are met, multilayer ceramic
8
capacitors may be operated with AC voltage applied without
need for DC bias.
STORAGE AND HANDLING
Ceramic chip capacitors should be stored in normal
working environments. While the chips themselves are quite
robust in other environments, solderability will be degraded
by exposure to high temperatures, high humidity, corrosive
atmospheres, and long term storage. In addition, packaging
materials will be degraded by high temperature – reels may
soften or warp, and tape peel force may increase. KEMET
recommends that maximum storage temperature not exceed
40˚ C, and maximum storage humidity not exceed 70% relative humidity. In addition, temperature fluctuations should be
minimized to avoid condensation on the parts, and atmospheres should be free of chlorine and sulfur bearing compounds. For optimized solderability, chip stock should be
used promptly, preferably within 1.5 years of receipt.
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
APPLICATION NOTES FOR MULTILAYER
CERAMIC CAPACITORS
IMPEDANCE VS FREQUENCY
0.20
100
Impedance vs. Frequency
Ceramic C0G
Leaded
.001μF
%ΔC
0.10
%DF
.01μF
100
%DF
-0.2
100
Figure 8.
1K
10K
100K
1M
0.0
10M
Frequency - Hertz
Capacitance & DF vs Frequency - C0G
Impedance (Ohms)
10
10.
Figure 10. Figure
-0.1
Impedance (Ohms)
%ΔC
+0.1
0
Application Notes
EFFECT OF FREQUENCY
+0.2
vs Frequency
ImpedanceImpedance
vs Frequency
for C0G Dielectric
for C0G Dielectric
10
1
0.001µF
1
0.1
10.
Figure 10. Figure
0.1
vs Frequency
vs 0.01µF
Frequency
ImpedanceImpedance
for C0G Dielectric
for C0G Dielectric
0.01
0.01 0.1
1
1 0
100
1000
Frequency - MHz
5.0
-10
2.5
-15
0.0
10M
100
1K
10K
100K
1M
Figure 9.
Frequency - Hertz
Capacitance & DF vs Frequency - X7R & Z5U
Figure 10.
Frequency - MHz
Impedance Impedance
vs Frequency
for C0G Dielectric
vs. Frequency
Leaded X7R
100
100
Impedance (Ohms)
%ΔC
%ΔC
-5
1,000
7.5
Impedance (Ohms)
%DF
0
Impedance
vs Frequency
Figure 10. Figure 10. Impedance vs
Frequency
10.0
0.001
for
C0G Dielectric
for
0.1
1 C0G Dielectric
10
100
%DF
+5
0.1μF
10
10
0.01µF
.01μF
0.1µF
1.0 μF
1
1.0µF Impedance
11. Impedance
vs Frequency
Figure 11. Figure
vs Frequency
1
0.1
for X7R Dielectric
for X7R Dielectric
EFFECT OF TIME (hours)
0.1
1
10
100
1000
Frequency - MHz
vs Frequency
Figure 11. Figure 11. ImpedanceImpedance
vs Frequency
0.01
for X7R Dielectric
for X7R Dielectric
X7R
X7R
Capacitance
Capacitance
0.001
0.1
1 Impedance vs.
10 Frequency
100
1,000
Z5U
Z5U
Impedance (Ohms)
Leaded Z5U
Figure
Impedance
vs Frequency
Figure 11.Figure
vs
Frequency
11.11.ImpedanceFrequency
- MHz
for X7Rfor
Dielectric
for
X7R
Dielectric
100
Impedance vs Frequency
X7R Dielectric
10
100
10
10
100
100
1000
1000
10K
10K
Figure 13. Typical Aging Rates for X7R & Z5U
100K
100K
Impedance (Ohms)
100%
100%
98%
98%
96%
96%
94%
94%
92%
92%
90%
90%
88%
88%
86%
86%
84%
84%
82%
82%
80%
80%
78%
78%
76%
76%
74%
74%
11
0.01
0.1
0.1µF
1
0.1μF
1.0µF
10
0.1
1.0 μF
0.01
1
0.1
1
1 0
100
1000
Frequency - MHz
vs Frequency
Figure 12. Figure 12. ImpedanceImpedance
vs Frequency
for Z5U Dielectric
for Z5U Dielectric
0.1
0.01
vs Frequency
Figure 12. Figure 12. ImpedanceImpedance
vs Frequency
for Z5U Dielectric
for Z5U Dielectric
0.001
0.1
1
10
100
1,000
Figure 12.
Frequency - MHz
Impedance vs Frequency for Z5U Dielectric
Impedance
vs Frequency
Figure 12. Figure 12.Impedance vs
Frequency
for Z5U Dielectric
for Z5U Dielectric
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
9
CERAMIC MOLDED/AXIAL
& RADIAL — MIL-PRF-20
CAPACITOROUTLINE
OUTLINEDRAWINGS
DRAWINGS- (AXIAL
CAPACITOR
(AXIALLEADS)
LEADS)
L
1.50 Min.
(38.10)
D
1.50 Min.
(38.10)
C
DIMENSIONS — INCHES (MILLIMETERS)
Case
Size
Military
Equivalent Styles
L
Length
D
Body Diameter
C
Lead Diameter
C114
CC75, CCR75
.160 ± .010 (4.06 ± .25)
.090 ± .010 (2.29 ± .25)
.020, +.000, -.003 (.51, +.00, -.08)
C124
CC76, CCR76
.250 ± .010 (6.35 ± .25)
.090 ± .010 (2.29 ± .25)
.020, +.000, -.003 (.51, +.00, -.08)
C192
CC77, CCR77
.390 ± .010 (9.91 ± .25)
.140 ± .010 (3.56 ± .25)
.025, +.004, -.001 (.64, +.10, -.025)
C202
CC78, CCR78
.500 ± .020 (12.70 ± .51)
.250 ± .015 (6.35 ± .38)
.025, +.004, -.001 (.64, +.10, -.025)
C222
CC79, CCR79
.690 ± .020 (17.53 ± .51)
.350 ± .015 (8.89 ± .38)
.025, +.004, -.001 (.64, +.10, -.025)
CAPACITOR OUTLINE DRAWINGS (RADIAL LEADS)
C052 (CC05, CCR05)
L
C062 (CC06, CCR06), C512 (CC07, CCR07),
C522 (CC08, CCR08)
C056 (CCR05)
L
W
H
1.25
MIN.
Lead Dia.
.025
(+.004
-.002)
1.25
MIN.
.026
MIN.
Lead Dia.
.025
(+.004
-.002)
S
S
1.25
MIN.
C066 (CCR06)
W
L
H
H
.045
MAX.
L
W
.026
MIN.
H
Lead Dia.
.025
(+.004
-.002)
1.25
MIN.
S
Center Line of leads within .030" of Center Line of case.
W
Lead Dia.
.025
(+.004
-.002)
S
Note: Leads are .625 minimum when tape and reel packaged
DIMENSIONS — INCHES (MILLIMETERS)
Case
Size
S
Lead
Spacing
Military
Equivalent Styles
H
Height
L
Length
W
Width
C062/
C066
CC05, CCR05
.190 ± .010 (4.83 ± .25)
.190 ± .010 (4.83 ± .25)
.090 ± .010 (2.29 ± .25)
.200 ± .015 (5.08 ± .38)
CC06, CCR06
.290 ± .010 (7.37 ± .25)
.290 ± .010 (7.37 ± .25)
.090 ± .010 (2.29 ± .25)
.200 ± .015 (5.08 ± .38)
C522
CC07, CCR07
CC08, CCR08
.480 ± .020 (12.19 ± .51)
.480 ± .020 (12.19 ± .51)
*.140 ± .010 (3.56 ± .25)
.400 ± .020 (10.16 ± .51)
C052/
C056
C512
.480 ± .020 (12.19 ± .51)
.480 ± .020 (12.19 ± .51)
.240 ± .010 (6.10 ± .25)
.400 ± .020 (10.16 ± .51)
* 0.200 (5.08) maximum for 100,000 pF only.
For packaging information, see pages 46, 47, and 48.
34
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
CERAMIC MOLDED/AXIAL
& RADIAL — MIL-PRF-20
CERAMIC
CASE SIZE
See Table Below
102
J
1
G
5
C
SPECIFICATION
G – MIL-PRF-20
CAPACITANCE PICOFARAD CODE
Expressed in picofarads (pF). First two digits represent
significant figures. Third digit specifies number of zeros
following except 9 indicates division by 10). Examples:
0.1 µF = 100,000 pF = 104 and 9.1 pF = 919. See
tables for standard values.
CAPACITANCE TOLERANCE
Standard
Others
G – ±2%
C – ±0.25pF
K – ±10%
F – ±1%
D – ±0.5pF
J – ±5%
B – ±0.1pF
Standard tolerances for each Series
are shown in the repetitive parts lists.
Radial
C052
C056
C062
C066
C512
C522
Case Sizes
Axial
C114
C124
C192
C202
C222
R
FAILURE RATE
A – Not Applicable
M – 1.0%
P – 0.1%
R – 0.01%
S – 0.001%
LEAD MATERIAL
C – 60/40 Tin/Lead (SnPb)
INTERNAL CONSTRUCTION
5 – Multilayer
MIL-PRF-20
C 052 G
ORDERING INFORMATION
TEMPERATURE CHARACTERISTIC
Capacitance Change with Temp.
KEMET
Military
EIA
Temp Measured withMeasured
Designator Equivalent Equivalent Range, out DC Bias
with Bias
°C
Voltage
(Rated Voltage)
G
*CG
(Ultra Stable) (See below)
C0G
(NP0)
-55 to
+125°
*CH – ±60 ppm/°C 8.2 pF-18.0 pF
*CJ – ±120 ppm/°C 4.3 pF-7.5 pF
*CK – ±250 ppm/°C 2.2 pF-3.9 pF
*CX – not measurable 0.1 pF-2.0 pF
±30
ppm/°C
±30
ppm/°C
WORKING VOLTAGE DC
2 – 200V; 1 – 100V; 5 – 50V
Part Number Example: C052G102J1G5CR (14 digits – no spaces)
CAPACITOR MARKING
CC(R) 75, 76
JCK
2R2
CM5
11AK
“J” Brand (CCR only), Temperature Characteristic
Capacitance
Capacitance Tolerance, Failure Rate (CCR only),
Year Code
Lot Code, Trademark (K)
CC(R) 77
CCR77C
G102JM
J31433
0804A
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
“J” Brand (CCR only), FSCM (Federal Source Code)
Date/Lot Code
CC(R) 78
CCR78CG
103FR
JAN K
31433
100V
0804A
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
“JAN” Brand (CCR only), Trademark (K)
FSCM (Federal Source Code)
Voltage
Date/Lot Code
CC(R) 79
CCR79CG
103KM
JAN K
31433
200V
0804A
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
“JAN” Brand (CCR only), Trademark
FSCM (Federal Source Code)
Voltage
Date/Lot Code
FRONT
CCR0
5CH1
00FR
REAR
CC(R) 05
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
** For the standoff style, a “V” is added after the
failure rate, or last character.
0804
AJ3
1433
Date Code
Lot Code, “J” Brand (CCR only),
FSCM (Federal Source Code)
FRONT
CCR06
CG102
JS
CC(R) 06
REAR
0804A
J100V
31433
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
** For the standoff style, a “V” is added after the
failure rate, or last character.
Date/LotCode
“J” Brand (CCR only), Voltage
FSCM (Federal Source Code)
CC(R) 07
CCR07CG
472KM
JAN KEMET
31433
200V 0804A
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
“JAN” Brand, Trademark
FSCM (Federal Source Code)
Voltage, Date/Lot Code
CCR08CG
472KM
JAN KEMET
31433
200V 0809A
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
“JAN” Brand, Trademark
FSCM (Federal Source Code)
Voltage, Date/Lot Code
CC(R) 08
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
35
CERAMIC MOLDED/AXIAL — MIL-PRF-20
ULTRA-STABLE TEMPERATURE CHARACTERISTIC — CG (EIA-C0G)
RATINGS & PART NUMBER REFERENCE
CAP.
pF
1.0
1.1
1.2
1.3
1.5
1.6
1.8
2.0
2.2
2.4
2.7
3.0
3.3
3.6
3.9
4.3
4.7
5.1
5.6
6.2
6.8
7.5
8.2
9.1
10.0
11.0
12.0
13.0
15.0
16.0
18.0
20.0
22.0
24.0
27.0
30.0
33.0
36.0
39.0
43.0
47.0
51.0
56.0
62.0
68.0
75.0
KEMET
PART NUMBER
MILITARY
STYLE CC
MILITARY
STYLE CCR
200 VOLT – C114 (CC(R)75 PER MIL-PRF-20/27)
C114G109(2)2G5C(1)
CC75CX1R0(2)
CCR75CX1R0(2)(1)
C114G119(2)2G5C(1)
CC75CX1R1(2)
CCR75CX1R1(2)(1)
C114G129(2)2G5C(1)
CC75CX1R2(2)
CCR75CX1R2(2)(1)
C114G139(2)2G5C(1)
CC75CX1R3(2)
CCR75CX1R3(2)(1)
C114G159(2)2G5C(1)
CC75CX1R5(2)
CCR75CX1R5(2)(1)
C114G169(2)2G5C(1)
CC75CX1R6(2)
CCR75CX1R6(2)(1)
C114G189(2)2G5C(1)
CC75CX1R8(2)
CCR75CX1R8(2)(1)
C114G209(2)2G5C(1)
CC75CX2R0(2)
CCR75CX2R0(2)(1)
C114G229(2)2G5C(1)
CC75CK2R2(2)
CCR75CK2R2(2)(1)
C114G249(2)2G5C(1)
CC75CK2R4(2)
CCR75CK2R4(2)(1)
C114G279(3)2G5C(1)
CC75CK2R7(3)
CCR75CK2R7(3)(1)
C114G309(3)2G5C(1)
CC75CK3R0(3)
CCR75CK3R0(3)(1)
C114G339(3)2G5C(1)
CC75CK3R3(3)
CCR75CK2R3(3)(1)
C114G369(3)2G5C(1)
CC75CK3R6(3)
CCR75CK3R6(3)(1)
C114G399(3)2G5C(1)
CC75CK3R9(3)
CCR75CK3R9(3)(1)
C114G439(3)2G5C(1)
CC75CJ4R3(3)
CCR75CJ4R3(3)(1)
C114G479(3)2G5C(1)
CC75CJ4R7(3)
CCR75CJ4R7(3)(1)
C114G519(3)2G5C(1)
CC75CJ5R1(3)
CCR75CJ5R1(3)(1)
C114G569(3)2G5C(1)
CC75CJ5R6(3)
CCR75CJ5R6(3)(1)
C114G629(3)2G5C(1)
CC75CJ6R2(3)
CCR75CJ6R2(3)(1)
C114G689(3)2G5C(1)
CC75CJ6R8(3)
CCR75CJ6R8(3)(1)
C114G759(3)2G5C(1)
CC75CJ7R5(3)
CCR75CJ7R5(3)(1)
C114G829(3)2G5C(1)
CC75CH8R2(3)
CCR75CH8R2(3)(1)
C114G919(3)2G5C(1)
CC75CH9R1(3)
CCR75CH9R1(3)(1)
C114G100(4)2G5C(1)
CC75CH100(4)
CCR75CH100(4)(1)
C114G110(4)2G5C(1)
CC75CH110(4)
CCR75CH110(4)(1)
C114G120(4)2G5C(1)
CC75CH120(4)
CCR75CH120(4)(1)
C114G130(4)2G5C(1)
CC75CH130(4)
CCR75CH130(4)(1)
C114G140(4)2G5C(1)
CC75CH140(4)
CCR75CH140(4)(1)
C114G160(4)2G5C(1)
CC75CH160(4)
CCR75CH160(4)(1)
C114G180(4)2G5C(1)
CC75CH180(4)
CCR75CH180(4)(1)
C114G200(4)2G5C(1)
CC75CG200(4)
CCR75CG200(4)(1)
C114G220(4)2G5C(1)
CC75CG220(4)
CCR75CG220(4)(1)
C114G240(4)2G5C(1)
CC75CG240(4)
CCR75CG240(4)(1)
C114G270(4)2G5C(1)
CC75CG270(4)
CCR75CG270(4)(1)
C114G300(4)2G5C(1)
CC75CG300(4)
CCR75CG300(4)(1)
C114G330(4)2G5C(1)
CC75CG330(4)
CCR75CG330(4)(1)
C114G360(4)2G5C(1)
CC75CG360(4)
CCR75CG360(4)(1)
C114G390(4)2G5C(1)
CC75CG390(4)
CCR75CG390(4)(1)
C114G430(4)2G5C(1)
CC75CG430(4)
CCR75CG430(4)(1)
C114G470(4)2G5C(1)
CC75CG470(4)
CCR75CG470(4)(1)
C114G510(4)2G5C(1)
CC75CG510(4)
CCR75CG510(4)(1)
C114G560(4)2G5C(1)
CC75CG560(4)
CCR75CG560(4)(1)
C114G620(4)2G5C(1)
CC75CG620(4)
CCR75CG620(4)(1)
C114G680(4)2G5C(1)
CC75CG680(4)
CCR75CG680(4)(1)
C114G750(4)2G5C(1)
CC75CG750(4)
CCR75CG750(4)(1)
To complete Part Number, insert the following letters:
(1) Available Failure Rates: A (CC styles only); M, P, R & S (CCR styles only).
(2) Available Capacitance Tolerances: B, C.
(3) Available Capacitance Tolerances: B, C, D.
(4) Available Capacitance Tolerances: F, G, J.
36
CAP.
pF
KEMET
PART NUMBER
MILITARY
STYLE CC
MILITARY STYLE
CCR
82.0
91.0
100.0
110.0
120.0
130.0
150.0
160.0
180.0
200.0
220.0
240.0
100 VOLT – C114 (CC(R)75 PER MIL-PRF-20/27)
C114G820(4)1G5C(1)
CC75CG820(4)
CCR75CG820(4)(1)
C114G910(4)1G5C(1)
CC75CG910(4)
CCR75CG910(4)(1)
C114G101(4)1G5C(1)
CC75CG101(4)
CCR75CG101(4)(1)
C114G111(4)1G5C(1)
CC75CG111(4)
CCR75CG111(4)(1)
C114G121(4)1G5C(1)
CC75CG121(4)
CCR75CG121(4)(1)
C114G131(4)1G5C(1)
CC75CG131(4)
CCR75CG131(4)(1)
C114G151(4)1G5C(1)
CC75CG151(4)
CCR75CG151(4)(1)
C114G161(4)1G5C(1)
CC75CG161(4)
CCR75CG161(4)(1)
C114G181(4)1G5C(1)
CC75CG181(4)
CCR75CG181(4)(1)
C114G201(4)1G5C(1)
CC75CG201(4)
CCR75CG201(4)(1)
C114G221(4)1G5C(1)
CC75CG221(4)
CCR75CG221(4)(1)
C114G241(4)1G5C(1)
CC75CG241(4)
CCR75CG241(4)(1)
270.0
300.0
330.0
360.0
390.0
430.0
470.0
510.0
560.0
620.0
680.0
50 VOLT – C114 (CC(R)75 PER MIL-PRF-20/27)
C114G271(4)5G5C(1)
CC75CG271(4)
CCR75CG271(4)(1)
C114G301(4)5G5C(1)
CC75CG301(4)
CCR75CG301(4)(1)
C114G331(4)5G5C(1)
CC75CG331(4)
CCR75CG331(4)(1)
C114G361(4)5G5C(1)
CC75CG361(4)
CCR75CG361(4)(1)
C114G391(4)5G5C(1)
CC75CG391(4)
CCR75CG391(4)(1)
C114G431(4)5G5C(1)
CC75CG431(4)
CCR75CG431(4)(1)
C114G471(4)5G5C(1)
CC75CG471(4)
CCR75CG471(4)(1)
C114G511(4)5G5C(1)
CC75CG511(4)
CCR75CG511(4)(1)
C114G561(4)5G5C(1)
CC75CG561(4)
CCR75CG561(4)(1)
C114G621(4)5G5C(1)
CC75CG621(4)
CCR75CG621(4)(1)
C114G681(4)5G5C(1)
CC75CG681(4)
CCR75CG681(4)(1)
82.0
91.0
100.0
110.0
120.0
130.0
200 VOLT – C124 (CC(R)76 PER MIL-PRF-20/28)
C124G820(4)2G5C(1)
CC76CG820(4)
CCR76CG820(4)(1)
C124G910(4)2G5C(1)
CC76CG910(4)
CCR76CG910(4)(1)
C124G101(4)2G5C(1)
CC76CG101(4)
CCR76CG101(4)(1)
C124G111(4)2G5C(1)
CC76CG111(4)
CCR76CG111(4)(1)
C124G121(4)2G5C(1)
CC76CG121(4)
CCR76CG121(4)(1)
C124G131(4)2G5C(1)
CC76CG131(4)
CCR76CG131(4)(1)
270.0
300.0
330.0
360.0
390.0
430.0
470.0
510.0
560.0
620.0
680.0
100 VOLT – C124 (CC(R)76 PER MIL-PRF-20/28)
C124G271(4)1G5C(1)
CC76CG271(4)
CCR76CG271(4)(1)
C124G301(4)1G5C(1)
CC76CG301(4)
CCR76CG301(4)(1)
C124G331(4)1G5C(1)
CC76CG331(4)
CCR76CG331(4)(1)
C124G361(4)1G5C(1)
CC76CG361(4)
CCR76CG361(4)(1)
C124G391(4)1G5C(1)
CC76CG391(4)
CCR76CG391(4)(1)
C124G431(4)1G5C(1)
CC76CG431(4)
CCR76CG431(4)(1)
C124G471(4)1G5C(1)
CC76CG471(4)
CCR76CG471(4)(1)
C124G511(4)1G5C(1)
CC76CG511(4)
CCR76CG511(4)(1)
C124G561(4)1G5C(1)
CC76CG561(4)
CCR76CG561(4)(1)
C124G621(4)1G5C(1)
CC76CG621(4)
CCR76CG621(4)(1)
C124G681(4)1G5C(1)
CC76CG681(4)
CCR76CG681(4)(1)
750.0
820.0
910.0
1,000.0
50 VOLT – C124 (CC(R)76 PER MIL-PRF-20/28)
C124G751(4)5G5C(1)
CC76CG751(4)
CCR76CG751(4)(1)
C124G821(4)5G5C(1)
CC76CG821(4)
CCR76CG821(4)(1)
C124G911(4)5G5C(1)
CC76CG911(4)
CCR76CG911(4)(1)
C124G102(4)5G5C(1)
CC76CG102(4)
CCR76CG102(4)(1)
150.0
160.0
180.0
200.0
220.0
240.0
270.0
300.0
330.0
360.0
390.0
430.0
470.0
510.0
560.0
620.0
680.0
200 VOLT – C192 (CC(R)77 PER MIL-PRF-20/29)
C192G151(4)2G5C(1)
CC77CG151(4)
CCR77CG151(4)(1)
C192G161(4)2G5C(1)
CC77CG161(4)
CCR77CG161(4)(1)
C192G181(4)2G5C(1)
CC77CG181(4)
CCR77CG181(4)(1)
C192G201(4)2G5C(1)
CC77CG201(4)
CCR77CG201(4)(1)
C192G221(4)2G5C(1)
CC77CG221(4)
CCR77CG221(4)(1)
C192G241(4)2G5C(1)
CC77CG241(4)
CCR77CG241(4)(1)
C192G271(4)2G5C(1)
CC77CG271(4)
CCR77CG271(4)(1)
C192G301(4)2G5C(1)
CC77CG301(4)
CCR77CG301(4)(1)
C192G331(4)2G5C(1)
CC77CG331(4)
CCR77CG331(4)(1)
C192G361(4)2G5C(1)
CC77CG361(4)
CCR77CG361(4)(1)
C192G391(4)2G5C(1)
CC77CG391(4)
CCR77CG391(4)(1)
C192G431(4)2G5C(1)
CC77CG431(4)
CCR77CG431(4)(1)
C192G471(4)2G5C(1)
CC77CG471(4)
CCR77CG471(4)(1)
C192G511(4)2G5C(1)
CC77CG511(4)
CCR77CG511(4)(1)
C192G561(4)2G5C(1)
CC77CG561(4)
CCR77CG561(4)(1)
C192G621(4)2G5C(1)
CC77CG621(4)
CCR77CG621(4)(1)
C192G681(4)2G5C(1)
CC77CG681(4)
CCR77CG681(4)(1)
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
CERAMIC MOLDED/AXIAL — MIL-PRF-20
ULTRA-STABLE TEMPERATURE CHARACTERISTIC — CG (EIA-C0G)
RATINGS & PART NUMBER REFERENCE
KEMET
PART NUMBER
MILITARY
STYLE CC
MILITARY
STYLE CCR
750.0
820.0
910.0
1,000.0
1,100.0
1,200.0
1,300.0
1,500.0
1,600.0
1,800.0
2,000.0
2,200.0
100 VOLT – C192 (CC(R)77 PER MIL-PRF-20/29)
C192G751(4)1G5C(1)
CC77CG751(4)
CCR77CG751(4)(1)
C192G821(4)1G5C(1)
CC77CG821(4)
CCR77CG821(4)(1)
C192G911(4)1G5C(1)
CC77CG911(4)
CCR77CG911(4)(1)
C192G102(4)1G5C(1)
CC77CG102(4)
CCR77CG102(4)(1)
C192G112(4)1G5C(1)
CC77CG112(4)
CCR77CG112(4)(1)
C192G122(4)1G5C(1)
CC77CG122(4)
CCR77CG122(4)(1)
C192G132(4)1G5C(1)
CC77CG132(4)
CCR77CG132(4)(1)
C192G152(4)1G5C(1)
CC77CG152(4)
CCR77CG152(4)(1)
C192G162(4)1G5C(1)
CC77CG162(4)
CCR77CG162(4)(1)
C192G182(4)1G5C(1)
CC77CG182(4)
CCR77CG182(4)(1)
C192G202(4)1G5C(1)
CC77CG202(4)
CCR77CG202(4)(1)
C192G222(4)1G5C(1)
CC77CG222(4)
CCR77CG222(4)(1)
2,400.0
2,700.0
3,000.0
3,300.0
3,600.0
3,900.0
4,300.0
4,700.0
5,100.0
5,600.0
50 VOLT – C192 (CC(R)77 PER MIL-PRF-20/29)
C192G242(4)5G5C(1)
CC77CG242(4)
CCR77CG242(4)(1)
C192G272(4)5G5C(1)
CC77CG272(4)
CCR77CG272(4)(1)
C192G302(4)5G5C(1)
CC77CG302(4)
CCR77CG302(4)(1)
C192G332(4)5G5C(1)
CC77CG332(4)
CCR77CG332(4)(1)
C192G362(4)5G5C(1)
CC77CG362(4)
CCR77CG362(4)(1)
C192G392(4)5G5C(1)
CC77CG392(4)
CCR77CG392(4)(1)
C192G432(4)5G5C(1)
CC77CG432(4)
CCR77CG432(4)(1)
C192G472(4)5G5C(1)
CC77CG472(4)
CCR77CG472(4)(1)
C192G512(5)5G5C(1)
CC77CG512(5)
CCR77CG512(5)(1)
C192G562(5)5G5C(1)
CC77CG562(5)
CCR77CG562(5)(1)
820.0
1,000.0
1,200.0
1,500.0
1,800.0
2,200.0
2,700.0
3,300.0
200 VOLT – C202 (CC(R)78 PER MIL-PRF-20/30)
C202G821(5)2G5C(1)
CC78CG821(5)
CCR78CG821(5)(1)
C202G102(5)2G5C(1)
CC78CG102(5)
CCR78CG102(5)(1)
C202G122(5)2G5C(1)
CC78CG122(5)
CCR78CG122(5)(1)
C202G152(5)2G5C(1)
CC78CG152(5)
CCR78CG152(5)(1)
C202G182(5)2G5C(1)
CC78CG182(5)
CCR78CG182(5)(1)
C202G222(5)2G5C(1)
CC78CG222(5)
CCR78CG222(5)(1)
C202G272(5)2G5C(1)
CC78CG272(5)
CCR78CG272(5)(1)
C202G332(5)2G5C(1)
CC78CG332(5)
CCR78CG332(5)(1)
CAP.
pF
KEMET
PART NUMBER
MILITARY STYLE
CC
MILITARY STYLE
CCR
3,900.0
4,700.0
5,600.0
6,800.0
8,200.0
10,000.0
12,000.0
100 VOLT – C202 (CC(R)78 PER MIL-PRF-20/30)
C202G392(5)1G5C(1)
CC78CG392(5)
CCR78CG392(5)(1)
C202G472(5)1G5C(1)
CC78CG472(5)
CCR78CG472(5)(1)
C202G562(5)1G5C(1)
CC78CG562(5)
CCR78CG562(5)(1)
C202G682(5)1G5C(1)
CC78CG682(5)
CCR78CG682(5)(1)
C202G822(5)1G5C(1)
CC78CG822(5)
CCR78CG822(5)(1)
C202G103(5)1G5C(1)
CC78CG103(5)
CCR78CG103(5)(1)
C202G123(5)1G5C(1)
CC78CG123(5)
CCR78CG123(5)(1)
15,000.0
18,000.0
22,000.0
27,000.0
50 VOLT – C202 (CC(R)78 PER MIL-PRF-20/30)
C202G153(5)5G5C(1)
CC78CG153(5)
CCR78CG153(5)(1)
C202G183(5)5G5C(1)
CC78CG183(5)
CCR78CG183(5)(1)
C202G223(5)5G5C(1)
CC78CG223(5)
CCR78CG223(5)(1)
C202G273(5)5G5C(1)
CC78CG273(5)
CCR78CG273(5)(1)
3,900.0
4,700.0
5,600.0
6,800.0
8,200.0
10,000.0
200 VOLT – C222 (CC(R)79 PER MIL-PRF-20/31)
C222G392(5)2G5C(1)
CC79CG392(5)
CCR79CG392(5)(1)
C222G472(5)2G5C(1)
CC79CG472(5)
CCR79CG472(5)(1)
C222G562(5)2G5C(1)
CC79CG562(5)
CCR79CG562(5)(1)
C222G682(5)2G5C(1)
CC79CG682(5)
CCR79CG682(5)(1)
C222G822(5)2G5C(1)
CC79CG822(5)
CCR79CG822(5)(1)
C222G103(5)2G5C(1)
CC79CG103(5)
CCR79CG103(5)(1)
15,000.0
18,000.0
22,000.0
27,000.0
33,000.0
39,000.0
100 VOLT – C222 (CC(R)79 PER MIL-PRF-20/31)
C222G153(5)1G5C(1)
CC79CG153(5)
CCR79CG153(5)(1)
C222G183(5)1G5C(1)
CC79CG183(5)
CCR79CG183(5)(1)
C222G223(5)1G5C(1)
CC79CG223(5)
CCR79CG223(5)(1)
C222G273(5)1G5C(1)
CC79CG273(5)
CCR79CG273(5)(1)
C222G333(5)1G5C(1)
CC79CG333(5)
CCR79CG333(5)(1)
C222G393(5)1G5C(1)
CC79CG393(5)
CCR79CG393(5)(1)
47,000.0
56,000.0
68,000.0
82,000.0
50 VOLT – C222 (CC(R)79 PER MIL-PRF-20/31)
C222G473(5)5G5C(1)
CC79CG473(5)
CCR79CG473(5)(1)
C222G563(5)5G5C(1)
CC79CG563(5)
CCR79CG563(5)(1)
C222G683(5)5G5C(1)
CC79CG683(5)
CCR79CG683(5)(1)
C222G823(5)5G5C(1)
CC79CG823(5)
CCR79CG823(5)(1)
To complete Part Number, insert the following letters:
(1) Available Failure Rates: A (CC styles only); M, P, R & S (CCR styles only).
(2) Available Capacitance Tolerances: B, C.
(3) Available Capacitance Tolerances: B, C, D.
(4) Available Capacitance Tolerances: F, G, J.
(5) Available Capacitance Tolerances: F, G, J, K.
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
37
MIL-PRF-20
CAP.
pF
CERAMIC MOLDED/RADIAL — MIL-PRF-20
ULTRA-STABLE TEMPERATURE CHARACTERISTIC — CG (EIA-C0G)
RATINGS & PART NUMBER REFERENCE
CAP.
pF
1.0
1.1
1.2
1.3
1.5
1.6
1.8
2.0
2.2
2.4
2.7
3.0
3.3
3.6
3.9
4.3
4.7
5.1
5.6
6.2
6.8
7.5
8.2
9.1
10.0
11.0
12.0
13.0
15.0
16.0
18.0
20.0
22.0
24.0
27.0
30.0
33.0
36.0
39.0
43.0
47.0
51.0
KEMET
PART NUMBER
MILITARY
STYLE CC
MILITARY
STYLE CCR
200 VOLT – C052/056 SIZE (CC(R)05 PER MIL-PRF-20/35)
C05(6)G109(2)2G5C(1)
CC05CX1R0(2)
CCR05CX1R0(2)(1)(7)
C05(6)G119(2)2G5C(1)
CC05CX1R1(2)
CCR05CX1R1(2)(1)(7)
C05(6)G129(2)2G5C(1)
CC05CX1R2(2)
CCR05CX1R2(2)(1)(7)
C05(6)G139(2)2G5C(1)
CC05CX1R3(2)
CCR05CX1R3(2)(1)(7)
C05(6)G159(2)2G5C(1)
CC05CX1R5(2)
CCR05CX1R5(2)(1)(7)
C05(6)G169(2)2G5C(1)
CC05CX1R6(2)
CCR05CX1R6(2)(1)(7)
C05(6)G189(2)2G5C(1)
CC05CX1R8(2)
CCR05CX1R8(2)(1)(7)
C05(6)G209(2)2G5C(1)
CC05CX2R0(2)
CCR05CX2R0(2)(1)(7)
C05(6)G229(2)2G5C(1)
CC05CK2R2(2)
CCR05CK2R2(2)(1)(7)
C05(6)G249(2)2G5C(1)
CC05CK2R4(2)
CCR05CK2R4(2)(1)(7)
C05(6)G279(3)2G5C(1)
CC05CK2R7(3)
CCR05CK2R7(3)(1)(7)
C05(6)G309(3)2G5C(1)
CC05CK3R0(3)
CCR05CK3R0(3)(1)(7)
C05(6)G339(3)2G5C(1)
CC05CK3R3(3)
CCR05CK3R3(3)(1)(7)
C05(6)G369(3)2G5C(1)
CC05CK3R6(3)
CCR05CK3R6(3)(1)(7)
C05(6)G399(3)2G5C(1)
CC05CK3R9(3)
CCR05CK3R9(3)(1)(7)
C05(6)G439(3)2G5C(1)
CC05CJ4R3(3)
CCR05CJ4R3(3)(1)(7)
C05(6)G479(3)2G5C(1)
CC05CJ4R7(3)
CCR05CJ4R7(3)(1)(7)
C05(6)G519(3)2G5C(1)
CC05CJ5R1(3)
CCR05CJ5R1(3)(1)(7)
C05(6)G569(3)2G5C(1)
CC05CJ5R6(3)
CCR05CJ5R6(3)(1)(7)
C05(6)G629(3)2G5C(1)
CC05CJ6R2(3)
CCR05CJ6R2(3)(1)(7)
C05(6)G689(3)2G5C(1)
CC05CJ6R8(3)
CCR05CJ6R8(3)(1)(7)
C05(6)G759(3)2G5C(1)
CC05CJ7R5(3)
CCR05CJ7R5(3)(1)(7)
C05(6)G829(3)2G5C(1)
CC05CH8R2(3)
CCR05CH8R2(3)(1)(7)
C05(6)G919(3)2G5C(1)
CC05CH9R1(3)
CCR05CH9R1(3)(1)(7)
C05(6)G100(4)2G5C(1)
CC05CH100(4)
CCR05CH100(4)(1)(7)
C05(6)G110(4)2G5C(1)
CC05CH110(4)
CCR05CH110(4)(1)(7)
C05(6)G120(4)2G5C(1)
CC05CH120(4)
CCR05CH120(4)(1)(7)
C05(6)G130(4)2G5C(1)
CC05CH130(4)
CCR05CH130(4)(1)(7)
C05(6)G150(4)2G5C(1)
CC05CH150(4)
CCR05CH150(4)(1)(7)
C05(6)G160(4)2G5C(1)
CC05CH160(4)
CCR05CH160(4)(1)(7)
C05(6)G180(4)2G5C(1)
CC05CH180(4)
CCR05CH180(4)(1)(7)
C05(6)G200(4)2G5C(1)
CC05CG200(4)
CCR05CG200(4)(1)(7)
C05(6)G220(4)2G5C(1)
CC05CG220(4)
CCR05CG220(4)(1)(7)
C05(6)G240(4)2G5C(1)
CC05CG240(4)
CCR05CG240(4)(1)(7)
C05(6)G270(4)2G5C(1)
CC05CG270(4)
CCR05CG270(4)(1)(7)
C05(6)G300(4)2G5C(1)
CC05CG300(4)
CCR05CG300(4)(1)(7)
C05(6)G330(4)2G5C(1)
CC05CG330(4)
CCR05CG330(4)(1)(7)
C05(6)G360(4)2G5C(1)
CC05CG360(4)
CCR05CG360(4)(1)(7)
C05(6)G390(4)2G5C(1)
CC05CG390(4)
CCR05CG390(4)(1)(7)
C05(6)G430(4)2G5C(1)
CC05CG430(4)
CCR05CG430(4)(1)(7)
C05(6)G470(4)2G5C(1)
CC05CG470(4)
CCR05CG470(4)(1)(7)
C05(6)G510(4)2G5C(1)
CC05CG510(4)
CCR05CG510(4)(1)(7)
To complete Part Number, insert the following letters:
(1) Available Failure Rates: A (CC styles only); M, P, R & S (CCR styles only).
(2) Available Capacitance Tolerances: B, C.
(3) Available Capacitance Tolerances: B, C, D.
(4) Available Capacitance Tolerances: F, G, J.
(5) Available Capacitance Tolerances: F, G, J, K.
(6) Insert “2” for standard design, Style C052G
Stand-offs are available
only as CCR’s, not available as CC.
Insert “6” for stand-off design, Style C056G
(7) Add “V” for stand-off design, Style C056G
And leave blank for the flat bottom design (C052G)
CAP.
pF
KEMET
PART NUMBER
MILITARY
STYLE CC
MILITARY STYLE
CCR
56.0
62.0
68.0
75.0
82.0
91.0
100.0
110.0
120.0
130.0
150.0
160.0
180.0
200.0
220.0
240.0
270.0
300.0
330.0
200 VOLT – C052/056 SIZE (CC(R)05 PER MIL-PRF-20/35)
C05(6)G560(4)2G5C(1)
CC05CG560(4)
CCR05CG560(4)(1)(7)
C05(6)G620(4)2G5C(1)
CC05CG620(4)
CCR05CG620(4)(1)(7)
C05(6)G680(4)2G5C(1)
CC05CG680(4)
CCR05CG680(4)(1)(7)
C05(6)G750(4)2G5C(1)
CC05CG750(4)
CCR05CG750(4)(1)(7)
C05(6)G820(4)2G5C(1)
CC05CG820(4)
CCR05CG820(4)(1)(7)
C05(6)G910(4)2G5C(1)
CC05CG910(4)
CCR05CG910(4)(1)(7)
C05(6)G101(4)2G5C(1)
CC05CG101(4)
CCR05CG101(4)(1)(7)
C05(6)G111(4)2G5C(1)
CC05CG111(4)
CCR05CG111(4)(1)(7)
C05(6)G121(4)2G5C(1)
CC05CG121(4)
CCR05CG121(4)(1)(7)
C05(6)G131(4)2G5C(1)
CC05CG131(4)
CCR05CG131(4)(1)(7)
C05(6)G131(4)2G5C(1)
CC05CG131(4)
CCR05CG131(4)(1)(7)
C05(6)G161(4)2G5C(1)
CC05CG161(4)
CCR05CG161(4)(1)(7)
C05(6)G181(4)2G5C(1)
CC05CG181(4)
CCR05CG181(4)(1)(7)
C05(6)G201(4)2G5C(1)
CC05CG201(4)
CCR05CG201(4)(1)(7)
C05(6)G221(4)2G5C(1)
CC05C221(4)
CCR05CG221(4)(1)(7)
C05(6)G241(4)2G5C(1)
CC05CG241(4)
CCR05CG241(4)(1)(7)
C05(6)G271(4)2G5C(1)
CC05CG271(4)
CCR05CG271(4)(1)(7)
C05(6)G301(4)2G5C(1)
CC05CG301(4)
CCR05CG301(4)(1)(7)
C05(6)G331(4)2G5C(1)
CC05CG331(4)
CCR05CG331(4)(1)(7)
360.0
390.0
430.0
470.0
510.0
560.0
620.0
680.0
750.0
820.0
910.0
1,000.0
1,100.0
1,200.0
1,300.0
1,500.0
1,600.0
1,800.0
100 VOLT – C052/056 SIZE (CC(R)05 PER MIL-PRF-20/35)
C05(6)G361(4)1G5C(1)
CC05CG361(4)
CCR05CG361(4)(1)(7)
C05(6)G391(4)1G5C(1)
CC05CG391(4)
CCR05CG391(4)(1)(7)
C05(6)G431(4)1G5C(1)
CC05CG431(4)
CCR05CG431(4)(1)(7)
C05(6)G471(4)1G5C(1)
CC05CG471(4)
CCR05CG471(4)(1)(7)
C05(6)G511(4)1G5C(1)
CC05CG511(4)
CCR05CG511(4)(1)(7)
C05(6)G561(4)1G5C(1)
CC05CG561(4)
CCR05CG561(4)(1)(7)
C05(6)G621(4)1G5C(1)
CC05CG621(4)
CCR05CG621(4)(1)(7)
C05(6)G681(4)1G5C(1)
CC05CG681(4)
CCR05CG681(4)(1)(7)
C05(6)G751(4)1G5C(1)
CC05CG751(4)
CCR05CG751(4)(1)(7)
C05(6)G821(4)1G5C(1)
CC05CG821(4)
CCR05CG821(4)(1)(7)
C05(6)G911(4)1G5C(1)
CC05CG911(4)
CCR05CG911(4)(1)(7)
C05(6)G102(4)1G5C(1)
CC05CG102(4)
CCR05CG102(4)(1)(7)
C05(6)G112(4)1G5C(1)
CC05CG112(4)
CCR05CG112(4)(1)(7)
C05(6)G122(4)1G5C(1)
CC05CG122(4)
CCR05CG122(4)(1)(7)
C05(6)G132(4)1G5C(1)
CC05CG132(4)
CCR05CG132(4)(1)(7)
C05(6)G152(4)1G5C(1)
CC05CG152(4)
CCR05CG152(4)(1)(7)
C05(6)G162(4)1G5C(1)
CC05CG162(4)
CCR05CG162(4)(1)(7)
C05(6)G182(4)1G5C(1)
CC05CG182(4)
CCR05CG182(4)(1)(7)
2,000.0
2,200.0
2,400.0
2,700.0
3,000.0
3,300.0
50 VOLT – C052/056 SIZE (CC(R)05 PER MIL-PRF-20/35)
C05(6)G202(4)5G5C(1)
CC05CG202(4)
CCR05CG202(4)(1)(7)
C05(6)G222(4)5G5C(1)
CC05CG222(4)
CCR05CG222(4)(1)(7)
C05(6)G242(4)5G5C(1)
CC05CG242(4)
CCR05CG242(4)(1)(7)
C05(6)G272(4)5G5C(1)
CC05CG272(4)
CCR05CG272(4)(1)(7)
C05(6)G302(4)5G5C(1)
CC05CG302(4)
CCR05CG302(4)(1)(7)
C05(6)G332(4)5G5C(1)
CC05CG332(4)
CCR05CG332(4)(1)(7)
}
38
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
CERAMIC MOLDED/RADIAL — MIL-PRF-20
ULTRA-STABLE TEMPERATURE CHARACTERISTIC — CG (EIA-C0G)
RATINGS & PART NUMBER REFERENCE
KEMET
PART NUMBER
MILITARY
STYLE CC
MILITARY STYLE
CCR
360.0
390.0
430.0
470.0
510.0
560.0
620.0
680.0
750.0
820.0
910.0
1,000.0
1,100.0
1,200.0
1,300.0
1,500.0
1,600.0
1,800.0
200 VOLT – C062/066 SIZE (CC(R)06 PER MIL-PRF-20/36)
C06(6)G361(4)2G5C(1)
CC06CG361(4)
CCR06CG361(4)(1)(7)
C06(6)G391(4)2G5C(1)
CC06CG391(4)
CCR06CG391(4)(1)(7)
C06(6)G431(4)2G5C(1)
CC06CG431(4)
CCR06CG431(4)(1)(7)
C06(6)G471(4)2G5C(1)
CC06CG471(4)
CCR06CG471(4)(1)(7)
C06(6)G511(4)2G5C(1)
CC06CG511(4)
CCR06CG511(4)(1)(7)
C06(6)G561(4)2G5C(1)
CC06CG561(4)
CCR06CG561(4)(1)(7)
C06(6)G621(4)2G5C(1)
CC06CG621(4)
CCR06CG621(4)(1)(7)
C06(6)G681(4)2G5C(1)
CC06CG681(4)
CCR06CG681(4)(1)(7)
C06(6)G751(4)2G5C(1)
CC06CG751(4)
CCR06CG751(4)(1)(7)
C06(6)G821(4)2G5C(1)
CC06CG821(4)
CCR06CG821(4)(1)(7)
C06(6)G911(4)2G5C(1)
CC06CG911(4)
CCR06CG911(4)(1)(7)
C06(6)G102(4)2G5C(1)
CC06CG102(4)
CCR06CG102(4)(1)(7)
C06(6)G112(4)2G5C(1)
CC06CG112(4)
CCR06CG112(4)(1)(7)
C06(6)G122(4)2G5C(1)
CC06CG122(4)
CCR06CG122(4)(1)(7)
C06(6)G132(4)2G5C(1)
CC06CG132(4)
CCR06CG132(4)(1)(7)
C06(6)G152(4)2G5C(1)
CC06CG152(4)
CCR06CG152(4)(1)(7)
C06(6)G162(4)2G5C(1)
CC06CG162(4)
CCR06CG162(4)(1)(7)
C06(6)G182(4)2G5C(1)
CC06CG182(4)
CCR06CG182(4)(1)(7)
2,000.0
2,200.0
2,400.0
2,700.0
3,000.0
3,300.0
3,600.0
3,900.0
4,300.0
4,700.0
100 VOLT – C062/066 SIZE (CC(R)06 PER MIL-PRF-20/36)
C06(6)G202(4)1G5C(1)
CC06CG202(4)
CCR06CG202(4)(1)(7)
C06(6)G222(4)1G5C(1)
CC06CG222(4)
CCR06CG222(4)(1)(7)
C06(6)G242(4)1G5C(1)
CC06CG242(4)
CCR06CG242(4)(1)(7)
C06(6)G272(4)1G5C(1)
CC06CG272(4)
CCR06CG272(4)(1)(7)
C06(6)G302(4)1G5C(1)
CC06CG302(4)
CCR06CG302(4)(1)(7)
C06(6)G332(4)1G5C(1)
CC06CG332(4)
CCR06CG332(4)(1)(7)
C06(6)G362(4)1G5C(1)
CC06CG362(4)
CCR06CG362(4)(1)(7)
C06(6)G392(4)1G5C(1)
CC06CG392(4)
CCR06CG392(4)(1)(7)
C06(6)G432(4)1G5C(1)
CC06CG432(4)
CCR06CG432(4)(1)(7)
C06(6)G472(4)1G5C(1)
CC06CG472(4)
CCR06CG472(4)(1)(7)
5,100.0
5,600.0
6,200.0
6,800.0
7,500.0
50 VOLT – C062/066 SIZE (CC(R)06 PER MIL-PRF-20/36)
C06(6)G512(5)5G5C(1)
CC06CG512(5)
CCR06CG512(5)(1)(7)
C06(6)G562(5)5G5C(1)
CC06CG562(5)
CCR06CG562(5)(1)(7)
C06(6)G622(5)5G5C(1)
CC06CG622(5)
CCR06CG622(5)(1)(7)
C06(6)G682(5)5G5C(1)
CC06CG682(5)
CCR06CG682(5)(1)(7)
C06(6)G752(5)5G5C(1)
CC06CG752(5)
CCR06CG752(5)(1)(7)
To complete Part Number, insert the following letters:
(1) Available Failure Rates: A (CC styles only); M, P, R & S (CCR styles only).
(2) Available Capacitance Tolerances: B, C.
(3) Available Capacitance Tolerances: B, C, D.
(4) Available Capacitance Tolerances: F, G, J.
(5) Available Capacitance Tolerances: F, G, J, K.
(6) Insert “2” for standard design, Style C062G
Stand-offs are available
only as CCR’s, not available as CC.
Insert “6” for stand-off design, Style C066G
(7) Add “V” for stand-off design, Style C066G
And leave blank for the flat bottom design (C062G)
(8) Available Capacitance Tolerances: G, J, K
CAP.
pF
KEMET
PART NUMBER
MILITARY
STYLE CC
MILITARY STYLE
CCR
8,200.0
9,100.0
10,000.0
12,000.0
15,000.0
18,000.0
50 VOLT – C062/066 SIZE (CC(R)06 PER MIL-PRF-20/36)
C06(6)G822(5)5G5C(1)
CC06CG822(5)
CCR06CG822(5)(1)(7)
C06(6)G912(5)5G5C(1)
CC06CG912(5)
CCR06CG912(5)(1)(7)
C06(6)G103(5)5G5C(1)
CC06CG103(5)
CCR06CG103(5)(1)(7)
C06(6)G123(5)5G5C(1)
CC06CG123(5)
CCR06CG123(5)(1)(7)
C06(6)G153(5)5G5C(1)
CC06CG153(5)
CCR06CG153(5)(1)(7)
C06(6)G183(5)5G5C(1)
CC06CG183(5)
CCR06CG183(5)(1)(7)
2,200.0
2,700.0
3,300.0
3,900.0
4,700.0
200 VOLT – C512 SIZE (CC(R)07 PER MIL-PRF-20/37)
C512G222(5)2G5C(1)
CC07CG222(5)
CCR07CG222(5)(1)
C512G272(5)2G5C(1)
CC07CG272(5)
CCR07CG272(5)(1)
C512G332(5)2G5C(1)
CC07CG332(5)
CCR07CG332(5)(1)
C512G392(5)2G5C(1)
CC07CG392(5)
CCR07CG392(5)(1)
C512G472(5)2G5C(1)
CC07CG472(5)
CCR07CG472(5)(1)
5,600.0
6,800.0
8,200.0
10,000.0
12,000.0
100 VOLT – C512 SIZE (CC(R)07 PER MIL-PRF-20/37)
C512G562(5)1G5C(1)
CC07CG562(5)
CCR07CG562(5)(1)
C512G682(5)1G5C(1)
CC07CG682(5)
CCR07CG682(5)(1)
C512G822(5)1G5C(1)
CC07CG822(5)
CCR07CG822(5)(1)
C512G103(5)1G5C(1)
CC07CG103(5)
CCR07CG103(5)(1)
C512G123(5)1G5C(1)
CC07CG123(5)
CCR07CG123(5)(1)
15,000.0
18,000.0
22,000.0
27,000.0
33,000.0
39,000.0
47,000.0
56,000.0
68,000.0
83,000.0
100,000.0
50 VOLT – C512 SIZE (CC(R)07 PER MIL-PRF-20/37)
C512G153(5)5G5C(1)
CC07CG153(5)
CCR07CG153(5)(1)
C512G183(5)5G5C(1)
CC07CG183(5)
CCR07CG183(5)(1)
C512G223(5)5G5C(1)
CC07CG223(5)
CCR07CG223(5)(1)
C512G273(5)5G5C(1)
CC07CG273(5)
CCR07CG273(5)(1)
C512G333(5)5G5C(1)
CC07CG333(5)
CCR07CG333(5)(1)
C512G393(5)5G5C(1)
CC07CG393(5)
CCR07CG393(5)(1)
C512G473(5)5G5C(1)
CC07CG473(5)
CCR07CG473(5)(1)
C512G563(5)5G5C(1)
CC07CG563(5)
CCR07CG563(5)(1)
C512G683(5)5G5C(1)
CC07CG683(5)
CCR07CG683(5)(1)
C512G833(5)5G5C(1)
CC07CG833(5)
CCR07CG833(5)(1)
C512G104(5)5G5C(1)
CC07CG104(5)
CCR07CG104(5)(1)
3,900.0
4,700.0
200 VOLT – C522 SIZE (CC(R)08 PER MIL-PRF-20/38)
C522G392(8)2G5C(1)
CC08CG392(8)
CCR08CG392(8)(1)
C522G472(8)2G5C(1)
CC08CG472(8)
CCR08CG472(8)(1)
15,000.0
18,000.0
100 VOLT – C522 SIZE (CC(R)08 PER MIL-PRF-20/38)
C522G153(8)1G5C(1)
CC08CG153(8)
CCR08CG153(8)(1)
C522G183(8)1G5C(1)
CC08CG183(8)
CCR08CG183(8)(1)
56,000.0
68,000.0
50 VOLT – C522 SIZE (CC(R)08 PER MIL-PRF-20/38)
C522G563(8)5G5C(1)
CC08CG563(8)
CCR08CG563(8)(1)
C522G683(8)5G5C(1)
CC08CG683(8)
CCR08CG683(8)(1)
}
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
39
MIL-PRF-20
CAP.
pF
CERAMIC LEADED
PACKAGING INFORMATION
Ceramic Axial
Lead Tape and Reel Packaging
KEMET offers standard reeling of Molded and Conformally
Coated Axial Leaded Ceramic Capacitors for automatic insertion
or lead forming machines per EIA specification RS-296. KEMET’s
internal specification four-digit suffix, 7200, is placed at the end of
the part number to designate tape and reel packaging, ie:
C410C104Z5U5CA7200.
Paper (50 lb.) test minimum is inserted between the layers of
capacitors wound on reels for component pitch ≤ 0.400”.
Capacitor lead length may extend only a maximum of .0625”
(1.59mm) beyond the tapes’ edges. Capacitors are centered in a
row between the two tapes and will deviate only ± 0.031
(0.79mm) from the row center. A minimum of 36” (91.5 cm) leader
tape is provided at each end of the reel capacitors. Universal
splicing clips are used to connect the tape. Standard reel
quantities are shown on page 48.
46
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
CERAMIC LEADED
Tape and Reel Packaging
PACKAGING INFORMATION
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
47
CERAMIC LEADED
PACKAGING INFORMATION
CERAMIC PACKAGING
KEMET
Series
C114C-K-G
C124C-K-G
C192C-K-G
C202C-K
C222C-K
C052C-K-G
C062C-K-G
C114G
C124G
C192G
C202G
C222G
C052/56G
C062/66G
C512G
C522G
C114T
C124T
C192T
C202T
C222T
C052/56T
C062/66T
C31X
C32X
C33X
C340
C350
C410
C412
C420
C430
C440
C512
C522
C617
C622/C623
C627/C628
C630/C631
C637/C638
C640/C641
C642/C643
C647/C648
C657/C658
C667/C668
Military
Style
CK12, CC75
CK13, CC76
CK14, CC77
CK15
CK16
CK05, CC05
CK06, CC06
CCR75
CCR76
CCR77
CC78-CCR78
CC79-CCR79
CCR05
CCR06
CC07-CCR07
CC08-CCR08
CKR11
CKR12
CKR14
CKR15
CKR16
CKR05
CKR06
N/A
N/A
Military
Specification
MIL-C-11015/
MIL-PRF-20
MIL-PRF-20
MIL-PRF-39014
N/A
N/A
Standard (1)
Bulk
Quantity
200/Box
200/Box
100/Box
25/Box
10/Tray
100/Bag
100/Bag
200/Box
200/Box
100/Box
25/Box
10/Tray
100/Bag
100/Bag
Footnote (2)
Footnote (2)
200/Box
200/Box
100/Box
25/Box
10/Tray
100/Bag
100/Bag
500/Bag
500/Bag
250/Bag
100/Bag
50/Bag
300/Box
200/Box
300/Box
200/Box
200/Box
Footnote (2)
Footnote (2)
250/Bag
100/Bag
100/Bag
100/Bag
50/Bag
50/Bag
50/Bag
50/Bag
50/Bag
50/Bag
Ammo Pack
Quantity
Maximum
2000
1500
2500
2500
1500
1000
N/A
4000
4000
4000
2000
2000
Maximum
Reel
Quantity
5000
5000
3000
500
300
2000
1500
5000
5000
3000
500
300
1700
1500
N/A
N/A
5000
5000
3000
500
300
1700
1500
2500
2500
1500
1000
500
5000
5000
5000
2500
2500
N/A
N/A
1000
500
500
500
500
500
500
500
500
500
NOTE: (1) Standard packaging refers to number of pieces per bag, tray or vial.
(2) Quantity varies. For further details, please consult the factory.
48
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
Reel
Size
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
N/A
N/A
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"
N/A
N/A
12"
12"
12"
12"
12"
12"
12"
12"
12"
12"