MA300ERU Series Wide 4:1 Input, 3W Single Output DIP DC/DC Converters Electrical Specifications Key Features: Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. • 3W Output Power Input Parameter • 4:1 Input Voltage Range Input Voltage Range • 1,500 VDC Isolation Input Start Voltage • 12 Standard Models • Efficiency to 83% • Compact DIP Case • -40°C to +85°C Operation • Industry Standard Pin-Out • Low Cost Conditions Min. 24 VDC Input 9.0 48 VDC Input 18.0 24 VDC Input 4.5 48 VDC Input 11.0 (Pi) Filter Input Filter No Load Input Power Typ. 24.0 48.0 7.0 16.0 Max. 36.0 75.0 9.0 18.0 Units 0.2 0.5 W Typ. ±1.0 ±1.5 ±0.2 ±0.2 30 35 0.5 ±2.0 ±0.02 Max. ±3.0 ±5.0 ±0.5 ±1.0 45 85 3.0 ±5.0 ±0.03 Units % % % % VDC VDC Output Parameter Output Voltage Accuracy No Load Output Voltage Accuracy Line Regulation Load Regulation Ripple (20 MHz) Noise (20 MHz) Transient Recovery Time, See Note 2 Transient Response Deviation Temperature Coefficient Output Over Voltage Protection Output Short Circuit, See Note 3 Conditions IOUT = 5% to 100% VIN = Min to Max VIN = Min to Max IOUT = 5% to 100% Min. See Note 1 25% Load Step Change 110 Continuous (Autorecovery) mV P - P mSec % %/°C % General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency EMI Characteristics Parameter Radiated Emissions Conducted Emissions ESD RS EFT Surge CS Voltage Dips Conditions 60 Seconds 500 VDC 100 kHz/0.1V Min. 1,500 1,000 Typ. Max. 120 250 Standard See Note 4 EN 55022 See Note 4 EN 55022 EN 61000-4-2 EN 61000-4-3 See Note 5 EN 61000-4-4 See Note 6 EN 61000-4-5 EN 61000-4-6 EN 61000-4-29 Units VDC M pF kHz Level Class A Class A Criteria B; ±4 kV Contact Criteria A; 10V/m Criteria B; ±2 kV Criteria B; ±2 kV Criteria A; 3 Vrms Criteria B; 0% - 70% Environmental MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight Conditions Min. Typ. -40 +25 -55 Free Air Convection RH, Non-condensing Ambient Max. +85 +125 Units °C °C 95 % See Mechanical Diagram (Page 4) Aluminum Alloy 0.49 Oz (15g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25°C, Gnd Benign Min. 1.0 Typ. Max. Units MHours Conditions 24 VDC Input 48 VDC Input 1.5 mm From Case for 10 Sec Min. -0.7 -0.7 Typ. Max. 50.0 100.0 300 Units Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com VDC °C www.micropowerdirect.com Model Selection Guide Input Model Number Voltage (VDC) Nominal Range Output Current (mA) Voltage Full-Load No-Load (VDC) Current Current (mA, Max) (mA, Min) Efficiency (%, Typ) Fuse Reflected Capacitive Ripple Rating Load Current Slow-Blow (µF, Max) (mA Typ) (mA) MA324S-03ERU 24 9.0 - 36.0 166 10 3.3 909 45 75 30.0 2,700 300 MA324S-05ERU 24 9.0 - 36.0 156 10 5.0 600 30 80 30.0 2,200 300 MA324S-09ERU 24 9.0 - 36.0 156 10 9.0 333 17 80 30.0 1,000 300 MA324S-12ERU 24 9.0 - 36.0 154 10 12.0 250 13 81 30.0 680 300 MA324S-15ERU 24 9.0 - 36.0 152 10 15.0 200 10 82 30.0 680 300 MA324S-24ERU 24 9.0 - 36.0 152 10 24.0 125 6 82 30.0 470 300 MA348S-03ERU 48 18.0 - 75.0 82 8 12.0 909 45 76 30.0 2,700 150 MA348S-05ERU 48 18.0 - 75.0 79 8 5.0 600 30 79 30.0 2,200 150 MA348S-09ERU 48 18.0 - 75.0 77 8 9.0 333 17 81 30.0 1,000 150 MA348S-12ERU 48 18.0 - 75.0 76 8 12.0 250 13 82 30.0 680 150 MA348S-15ERU 48 18.0 - 75.0 75 8 15.0 200 10 83 30.0 680 150 MA348S-24ERU 48 18.0 - 75.0 77 8 24.0 125 6 81 30.0 470 150 Notes: 1. When measuring output ripple & noise, it is recommended that an external capacitor (1 µF to 10 µF) be placed from the +VOUT to the -VOUT pins. 2. Transient recovery is measured to within a 1% error band for a load step change of 25%. 3. Short circuit protection is provided by a “hiccup mode” circuit. 4. All units are rated for EN 55022 (CE/RE) class A without external components. They will meet class B with the addition of the discrete filter circuit as shown on page 3. Contact the factory for more information. 5. To meet the requirements of EN 61000-4-4 (±2 kV), external components are needed, as shown on page 3. Contact the factory for more information. 6. To meet the requirements of EN 61000-4-5 (±2 kV), external components are needed. This can be done discretely as shown on page 3. Contact the factory for more information. 7. These units should not be operated with a load under 5% of full load. Operation at no-load will not damage the unit, but they may not meet all specifications. 8. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Efficiency vs Input Voltage 24 VDC Input Efficiency vs Input Voltage 48 VDC Input Efficiency vs Output Load 24 VDC Input Efficiency vs Output Load 48 VDC Input 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected] The diagram below illustrates a typical connection of the MA300SERU series for applications that require meeting EMC standards. The units do not require external components to operate as specified. Some notes on this diagram (starting with the input circuit) are: 1. It is recommended that an external fuse be used. The recommended fuse is shown in the model chart on page 2. 2. An external MOV is recommended on the input to protect the unit in the event of a surge. A recommended value is given in the table at below. 3. The output filtering capacitor (C4) is a low ESR electrolytic capacitor. Care must be taken in choosing this capacitor not to exceed the capacitive load specification for the unit. Voltage derating of capacitors should be 80% or above. 4. Recommended values for components are: Component MOV C1 C2 LDM1 C3 CY1 C4 24 VIN S14K35 330 µF/50V 4.7 µF/50V 12 µH 4.7 µF/50V 1.0 nF/2 kV 10 µF www.micropowerdirect.com Derating Curve 48 VIN S14K60 330 µF/100V 4.7 µF/100V 12 µH 4.7 µF/100V 1.0 nF/2 kV 10 µF 5. The “Typical Board Layout” drawing shows a suggested board layout for the EMC/ EMI circuit. Filtering capacitor (C4) is a low ESR resistance electrolytic capacitor. Care must be taken in choosing this capacitor not to exceed the capacitive load specification for the unit. 6. In many applications simply adding input/output capacitors will enhance the input surge protection and reduce output ripple sufficiently. Typically, the value of the input capacitor should be 10 µF to 47 µF. The recommended output capacitor would be 10 µF. A typical board layout for this connection is shown at the bottom of this page. Typical Connection Typical Board Layout: With External Filter/Surge Components Typical Board Layout: With External Input/Output Capacitors MicroPower Direct • 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected] www.micropowerdirect.com Mechanical Dimensions Pin Connections Pin 2 3 11 14 16 22 23 Single Output -Vin -Vin No Connection +Vout -Vout +Vin +Vin Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) • Pin 1 is marked by a “dot” or indentation on the top of the unit Packing Tube Dimensions Notes: • • • • Tube length equals 20.866 (530), unit quantity equals 15 pcs. Tube length equals 8.661 (220), unit quantity equals 6 pcs. All dimensions are typical in inches (mm) Tolerance x.xx = ±0.02 (±0.50) MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]