MBRS1100T3, MBRS190T3 Preferred Devices Schottky Power Rectifier Surface Mount Power Package Schottky Power Rectifiers employ the use of the Schottky Barrier principle in a large area metal-to-silicon power diode. State-of-the-art geometry features epitaxial construction with oxide passivation and metal overlay contact. Ideally suited for low voltage, high frequency rectification, or as free wheeling and polarity protection diodes, in surface mount applications where compact size and weight are critical to the system. These state-of-the-art devices have the following features: Features • • • • • • • Pb−Free Packages are Available Small Compact Surface Mountable Package with J-Bend Leads Rectangular Package for Automated Handling Highly Stable Oxide Passivated Junction High Blocking Voltage − 100 Volts 175°C Operating Junction Temperature Guardring for Stress Protection http://onsemi.com SCHOTTKY BARRIER RECTIFIER 1.0 AMPERE 90, 100 VOLTS SMB CASE 403A PLASTIC MARKING DIAGRAM Mechanical Characteristics • Case: Epoxy, Molded • Weight: 95 mg (approximately) • Finish: All External Surfaces Corrosion Resistant and Terminal • • • Leads are Readily Solderable Lead and Mounting Surface Temperature for Soldering Purposes: 260°C Max. for 10 Seconds Shipped in 12 mm Tape and Reel, 2500 units per reel Cathode Polarity Band AYW B1xG B1 x A Y W G = Device Code = C for MBRS1100T3 9 for MBRS190T3 = Assembly Location = Year = Work Week = Pb−Free Package MAXIMUM RATINGS Rating Symbol Value Unit Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage MBRS190T3 MBRS1100T3 VRRM VRWM VR Average Rectified Forward Current TL = 163°C TL = 148°C IF(AV) Non−Repetitive Peak Surge Current (Surge Applied at Rated Load Conditions Halfwave, Single Phase, 60 Hz) IFSM 50 TJ −65 to +175 °C dv/dt 10 V/ns Operating Junction Temperature (Note 1) Voltage Rate of Change V ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. 90 100 A Preferred devices are recommended choices for future use and best overall value. 1.0 2.0 A Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. The heat generated must be less than the thermal conductivity from Junction−to−Ambient: dPD/dTJ < 1/RqJA. © Semiconductor Components Industries, LLC, 2007 March, 2007 − Rev. 9 1 Publication Order Number: MBRS1100T3/D MBRS1100T3, MBRS190T3 THERMAL CHARACTERISTICS Rating Symbol Value Unit RqJL 22 °C/W Maximum Instantaneous Forward Voltage (Note 1) (iF = 1.0 A, TJ = 25°C) VF 0.75 V Maximum Instantaneous Reverse Current (Note 1) (Rated dc Voltage, TJ = 25°C) (Rated dc Voltage, TJ = 100°C) IR Thermal Resistance − Junction−to−Lead (TL = 25°C) ELECTRICAL CHARACTERISTICS mA 0.5 5.0 1. Pulse Test: Pulse Width = 300 ms, Duty Cycle ≤ 2.0%. ORDERING INFORMATION Marking Package Shipping † MBRS1100T3 B1C SMB 2500 Tape & Reel MBRS1100T3G B1C SMB (Pb−Free) 2500 Tape & Reel MBRS190T3 B19 SMB 2500 Tape & Reel MBRS190T3G B19 SMB (Pb−Free) 2500 Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 2 MBRS1100T3, MBRS190T3 1K 400 200 100 40 20 10 4 2 1 0.4 0.2 0.1 0.04 0.02 0.01 20 10 TJ = 150°C 5 2 100°C 1 0.5 25°C 0.2 0.1 0.05 0.02 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 TJ = 150°C I R , REVERSE CURRENT (μA) i F, INSTANTANEOUS FORWARD CURRENT (AMPS) TYPICAL ELECTRICAL CHARACTERISTICS 1 1.1 1.2 1.3 125°C 100°C 25°C 0 10 20 vF, INSTANTANEOUS VOLTAGE (VOLTS) 30 40 50 60 70 80 90 100 VR, REVERSE VOLTAGE (VOLTS) Figure 1. Typical Forward Voltage Figure 2. Typical Reverse Current* 3.2 2.0 2.8 TJ = 100°C 2.4 SQUARE WAVE 1.0 DC 1.2 0.8 SQUARE WAVE 0.5 0.4 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 0 145 150 155 160 165 170 175 IF(AV), AVERAGE FORWARD CURRENT (AMPS) TC, CASE TEMPERATURE (°C) Figure 3. Power Dissipation Figure 4. Current Derating, Case, Per Leg TYPICAL ELECTRICAL CHARACTERISTICS C, CAPACITANCE (pF) 0 DC 1.5 2.0 1.6 I F(AV), AVERAGE FORWARD CURRENT (AMPS) PF(AV), AVERAGE POWER DISSIPATION (WATTS) *The curves shown are typical for the highest voltage device in the voltage grouping. Typical reverse current for lower voltage selections can be estimated from these curves if VR is sufficient below rated VR. 280 260 240 220 200 180 160 140 120 100 80 60 40 20 0 NOTE: TYPICAL CAPACITANCE NOTE: AT 0 V = 270 pF 0.1 0.2 0.5 1 2 5 10 20 VR, REVERSE VOLTAGE (VOLTS) Figure 5. Typical Capacitance http://onsemi.com 3 50 100 180 MBRS1100T3, MBRS190T3 PACKAGE DIMENSIONS SMB PLASTIC PACKAGE CASE 403A−03 ISSUE F HE NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. D DIMENSION SHALL BE MEASURED WITHIN DIMENSION P. E b DIM A A1 b c D E HE L L1 D MIN 1.90 0.05 1.96 0.15 3.30 4.06 5.21 0.76 MILLIMETERS NOM MAX 2.13 2.45 0.10 0.20 2.03 2.20 0.23 0.31 3.56 3.95 4.32 4.60 5.44 5.60 1.02 1.60 0.51 REF MIN 0.075 0.002 0.077 0.006 0.130 0.160 0.205 0.030 INCHES NOM 0.084 0.004 0.080 0.009 0.140 0.170 0.214 0.040 0.020 REF MAX 0.096 0.008 0.087 0.012 0.156 0.181 0.220 0.063 A L L1 A1 c SOLDERING FOOTPRINT* 2.261 0.089 2.743 0.108 2.159 0.085 SCALE 8:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 4 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MBRS1100T3/D