EPCOS B37931K9105K070 Multilayer ceramic capacitor highcv, x7r, 16 v and 25 v Datasheet

Multilayer ceramic capacitor
HighCV, X7R, 16 V and 25 V
Series/Type:
Chip
Ordering code: B37***K
Date:
Version:
15.07.2005
1
Content of inside pages of data sheet. Data will be automatically entered into headers and
footers. Please fill in the table and then change the colour to “White”. This ensures that the
table disappears for the customer pdf.
Identification/Classification 1: (header 1)
Multilayer ceramic capacitor
Identification/Classification 2: (header 2)
HighCV, X7R, 16 V and 25 V
Ordering code:
B37***K
Series/Type:
Chip
Preliminary data (optional): (if necessary)
Department:
KB VS PE
Date:
15.07.2005
Prepared by:
Release signed PE:
Release signed QS:
Modifications/Remarks:
Mr. Wischnat
Dr. Engel
Dr. Slakhorst
xx
xx
xx
 EPCOS AG 2005. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information
contained therein without EPCOS' prior express consent is prohibited.
Multilayer ceramic capacitor
HighCV, X7R, 16 V and 25 V
B37***K
Chip
Ordering code
B37872
K 0 105 K 0 62
Type and size:
931 = X7R / 0603
941 = X7R / 0805
872 = X7R / 1206
Metallization type:
K = Ag/Ni/Sn
Rated voltage:
9 = 16 V
0 = 25 V
Rated capacitance (example):
105 = 10 · 105 pF (1 µF)
Capacitance tolerance:
K = ±10%
Internal code
Packaging code:
60 = cardboard tape, 180-mm reel
70 = cardboard tape, 330-mm reel
62 = blister tape, 180-mm reel
72 = blister tape, 330-mm reel
KB VS PE
Please read the important notes on page 6
and the cautions and warnings.
15.07.2005
Page 2 of 6
Multilayer ceramic capacitor
HighCV, X7R, 16 V and 25 V
B37***K
Chip
Dimensional drawing
Size
l
[inch / mm]
[mm]
0603 / 1608 1.6 ±0.15
0805 / 2012 2.0 ±0.20
1206 / 3216 3.2 ±0.20
b
s
[mm]
[mm]
0.80 ±0.1 0.8 ±0,1
1.25 ±0.15 1.35 max.
1.60 ±0.15 1.2 ±0.1
k
[mm]
0.10 – 0.4
0.13 – 0.75
0.25 – 0.75
see also “Ordering codes and chip thickness”, dimensions in accordance to
CECC 32101-801
Electrical data
Temperature characteristic:
Climatic category (IEC 60068-1):
Standard:
Dielectric:
Rated voltage:
Capacitance1) test conditions
Test frequency:
Test voltage:
Max. relative capacitance change:
X7R
55/125/56
EIA
Class 2
16 V / 25 V
Dissipation factor tanδ (limit value):
< 25 · 10-3
Time constant τ at +25 °C:
Operating temperature range:
Capacitance values:
> 500 s
–55 °C ... +125 °C
220 nF … 2.2 µF
1)
(1.0 ±0.2) kHz
(1.0 ±0.2) VRMS
±15%
Subject to aging, please see “General Technical Information” at
www.epcos.com/ceramic_capacitors
or the data book “Multilayer Ceramic Capacitors”.
KB VS PE
Please read the important notes on page 6
and the cautions and warnings.
15.07.2005
Page 3 of 6
Multilayer ceramic capacitor
HighCV, X7R, 16 V and 25 V
B37***K
Chip
Ordering codes and chip thickness
Case size
[inch]
16 V types
0603
0805
CR
[mm]
[µF]
0.220
0.220
0.330
0.470
1.0
1.0
2.2
B37931K9224K060*
B37941K9224K060*
B37941K9334K060*
B37941K9474K060*
B37941K9105K062**
B37872K9105K062**
B37872K9225K062**
Size
CR
Ordering code
[inch]
[µF]
1206
25 V types
0603
0805
1206
Thickness
Ordering code
0.220
0.220
0.330
0.470
1.0
1.0
2.2
* Ordering Code Example
** Ordering Code Example
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
1.25 ±0.1
1.2 ±0.1
1.2 ±0.1
Thickness
[mm]
B37931K0224K060*
B37941K0224K060*
B37941K0334K060*
B37941K0474K060*
B37941K0105K062**
B37872K0105K062**
B37872K0225K062**
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
0.8 ±0.1
1.25 ±0.1
1.2 ±0.1
1.2 ±0.1
Packing quantity
∅ 180-mm
reel
[pcs]
∅ 330-mm
reel
[pcs]
4000
4000
4000
4000
3000
3000
3000
16000
16000
16000
16000
12000
12000
12000
Packing quantity
∅ 180-mm
reel
[pcs]
∅ 330-mm
reel
[pcs]
4000
4000
4000
4000
3000
3000
3000
16000
16000
16000
16000
12000
12000
12000
Standard tolerance:
± 10%
Standard packaging:
Cardboard tape, 180-mm reel
Standard tolerance:
± 10%
Standard packaging:
Blister tape, 180-mm reel
KB VS PE
Please read the important notes on page 6
and the cautions and warnings.
15.07.2005
Page 4 of 6
Multilayer ceramic capacitor
HighCV, X7R, 16 V and 25 V
B37***K
Chip
Further information
Please see General Technical Information at www.epcos.com/ceramic_capacitors or the data book
“Multilayer Ceramic Capacitors” for further information on:
Soldering directions
Taping and packing
Surface mounting instructions
Effects of mechanical stress
KB VS PE
Please read the important notes on page 6
and the cautions and warnings.
15.07.2005
Page 5 of 6
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As a
rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of passive electronic components
or failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in which
the malfunction or failure of a passive electronic component could endanger human life or health
(e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of
suitable design of the customer application or other action taken by the customer (e.g. installation
of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the
event of malfunction or failure of a passive electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as “hazardous”). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequently,
we cannot guarantee that all products named in this publication will always be available.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of
the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, CeraDiode, CSSP, PhaseCap, PhaseMod, SIFI, SIKOREL, SilverCap,
SIMID, SIOV, SIP5D, SIP5K, TOPcap, UltraCap, WindCap are trademarks registered or
pending in Europe and in other countries. Further information will be found on the Internet at
www.epcos.com/trademarks.
Page 6 of 6
Similar pages