ASL13W 5-3000 MHz MMIC Amplifier Features Description ·13 dB Gain at 2000 MHz The ASL13W, a wideband linear low noise amplifier MMIC, has a low noise and high linearity at low bias current, being suitable for use in both receiver and transmitter of telecommunication systems up to 3 GHz. S11 down to –20 dB is easily achieved for low noise application to provide a good productivity. The amplifier is available in an SOT-363 package and passes through the stringent DC, RF, and reliability tests. ·22 dBm P1dB at 2000 MHz ·38 dBm OIP3 at 2000 MHz ·0.9 dB NF at 2000 MHz ·MTTF > 100 Years ·Single Supply Package Style: SOT-363 Typical Performance Parameters Frequency Units Application Circuit Typical MHz 150 900 2000 2450 2600 Gain dB 23.5 19 13 11.5 11 · IF ( 50 ~ 450 MHz ) S11 dB -15 -20 -20 -20 -18 · TETRA dB -11 -15 -15 -16 -15 · LTE S22 dBm 33 35.5 38 37.5 37.5 · CDMA Noise Figure dB 0.6 0.9 0.9 1.1 1.15 · GSM Output P1dB dBm 21.5 22 22 22 22 · WCDMA Current mA 60 60 60 60 60 · 350 ~ 500 MHz V 5 5 5 5 5 · 960 ~ 1200 MHz 1) Output IP3 Device Voltage · 2300 ~ 2600 MHz 1) OIP3 is measured with two tones at an output power of +10 dBm/tone separated by 1 MHz. Product Specifications Parameters Testing Frequency Units Min MHz Typ 2000 Gain dB S11 dB -20 S22 dB -15 Output IP3 dBm 12 36 13 38 Noise Figure dB Output P1dB dBm 20 22 Current mA 45 60 Device Voltage V Max 0.9 1.1 80 5 Absolute Maximum Ratings Parameters Pin Configuration Rating Pin No. Function -40 to +150°C 1 RF IN Operating Case Temperature -40 to +85°C Storage Temperature Device Voltage +6 V 4 RF OUT / Bias Operating Junction Temperature +150°C 2,3,5,6 GND Input RF Power (CW, 50ohm matched)* 22 dBm * Please find the max. input power data from http://www.asb.co.kr/pdf/Maximum_Input_Power_Analysis.pdf 1/14 ASB Inc. · [email protected] · Tel: +82-42-528-7223 April 2012 ASL13W 5-3000 MHz MMIC Amplifier Outline Drawing Symbols Dimensions (In mm) NOM 1.00 0.062 0.937 0.30 0.125 2.00 1.25 2.10 0.65BSC 1.30BSC 0.425REF A A1 A2 b C D F E1 e e1 L MIN 0.90 0.025 0.875 0.20 0.10 1.90 1.15 2.00 ---- MAX 1.10 0.10 1.00 0.40 0.15 2.10 1.35 2.20 ---- Pin NO. Function Pin NO. Function. 1 RF IN 4 RF OUT / Bias 2 GND 5 GND 3 GND 6 GND Mounting Recommendation (in mm) Note: 1. The number and size of ground via holes in a circuit board is critical for thermal and RF grounding considerations. 2. We recommend that the ground via holes be placed on the bottom of lead pin 2 for better RF and thermal performance, as shown in the drawing at the left side. ESD Classification & Moisture Sensitivity Level ESD Classification HBM Class 1A Voltage Level: 400 V MM Class A Voltage Level: 50 V CAUTION: ESD-sensitive device! Moisture Sensitivity Level (MSL) Level 3 at 260°C reflow 2/14 ASB Inc. · [email protected] · Tel: +82-42-528-7223 April 2012 ASL13W 5-3000 MHz MMIC Amplifier OIP3 & Noise Figure Vs. Bias Resistor CDMA RD RB VD Ic (V) (mA) NF (ohm) (ohm) WCDMA OIP3 NF CDMA RD RB VD Ic (ohm) (ohm) (V) (mA) OIP3 (dB) (dBm) (dB) (dBm) WCDMA NF OIP3 NF OIP3 (dB) (dBm) (dB) (dBm) 5.6k 4.47 60 0.89 36 0.9 38.2 6.8k 3.87 51 0.83 35.3 0.89 37 5.1k 4.58 56 0.89 34.5 0.89 36.2 6.2k 4.09 47 0.83 34 0.89 36 4.7k 4.87 39 0.91 32 0.93 33.4 5.6k 4.28 39 0.86 32.2 0.89 34.7 4.3k 4.9 28 0.88 28.7 0.9 30.1 5.1k 4.35 32 0.86 29.8 0.9 31.8 5.6k 4.38 58 0.87 35.6 0.89 37.5 4.7k 4.5 28 0.86 27.2 0.91 29.5 5.1k 4.49 45 0.82 33.5 0.92 35.4 8.2k 3.31 57 0.8 34.9 0.88 37 4.7k 4.6 38 0.84 31.4 0.9 32.2 7.5k 3.47 50 0.83 33.9 0.87 36.3 4.3k 4.71 27 0.85 27.8 0.94 29.3 6.8k 3.68 44 0.82 32.8 0.87 35.3 8.2 20 10 30 12 15 6.2k 4.25 62 0.82 35.9 0.91 37.6 6.2k 3.84 38 0.83 30.8 0.88 33.4 5.6k 4.33 51 0.82 35.1 0.89 36.8 5.6k 4.01 33 .81 28.7 0.89 31.6 5.1k 4.49 42 0.81 32.4 0.91 34 5.1k 4.19 29 0.85 26.7 0.91 29.5 4.7k 4.57 33 0.84 30 0.91 31.5 4.3k 4.7 28 0.86 27 0.91 29.2 6.2k 4.15 57 0.82 35.3 0.93 37 5.6k 4.28 49 0.85 34.1 0.89 35.9 5.1k 4.4 38 0.84 31.7 0.88 33.3 4.7k 4.54 29 0.87 28.5 0.9 30.6 4.3k 4.63 26 0.85 26.1 0.92 28.9 * Test Application Circuit : ASL13W CDMA / WCDMA application circuit * OIP3 Test Condition : Freq. – 894MHz / – 2140MHz, +10dBm output power per tone * VD : Applied voltage to the device 3/14 ASB Inc. · [email protected] · Tel: +82-42-528-7223 April 2012 ASL13W 5-3000 MHz MMIC Amplifier Frequency (MHz) APPLICATION CIRCUIT IF 50 ~ 450 +5 V 50 150 300 450 Magnitude S21 (dB) 24.7 23.5 22.3 21 Magnitude S11 (dB) -12 -15 -14 -12 Magnitude S22 (dB) -12 -11 -12 -13 Output P1dB (dBm) 21.5 21.5 21.5 21.5 Output IP31) (dBm) 31 33 35 35 Noise Figure (dB) 0.8 0.6 0.8 0.8 Device Voltage (V) 5 5 5 5 Current (mA) 60 60 60 60 1) OIP3 is measured with two tones at an output power of +10 dBm/tone separated by 1 MHz. 2 Vs=5 V Board Layout (FR4, 40x40 mm , 0.8T) Schematic RD =8.2 W Note: A shunt RB is a bias resistor requisite to operate ASL13W properly, while RD as a voltage drop resistor is added to apply 4.4 V to the device. A user can easily REDUCE an operating current by choosing different RB values with minimized loss only in OIP3 and P1dB. C1=1 mF C5=10 mF C4=100 pF L1=1.2 mH RF IN C2=1 mF ASL13W RF OUT RB =5.6 kW R1=1.6 kW C3=1 nF S-parameters & K-factor 30 0 25 -10 S11 (dB) Gain (dB) -5 20 15 10 -20 5 0 -15 0 100 200 300 400 500 -25 0 100 200 Frequency (MHz) 0 5 -5 4 Stability Factor S22 (dB) -10 -15 -20 -25 400 500 3 2 1 0 100 200 300 400 500 0 0 500 Frequency (MHz) 4/14 300 Frequency (MHz) 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 April 2012 ASL13W 5-3000 MHz MMIC Amplifier Frequency (MHz) APPLICATION CIRCUIT TETRA 420~460 Magnitude S21 (dB) 23 Magnitude S11 (dB) -15 Magnitude S22 (dB) -18 Output P1dB (dBm) 22 1) 420 ~ 460 +5 V Output IP3 (dBm) 34 Noise Figure (dB) 0.7 Device Voltage (V) 5 Current (mA) 60 1) OIP3 is measured with two tones at an output power of +10 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vcc=5 V Note: A shunt RB is a bias resistor requisite to operate ASL13W properly, while RD as a voltage drop resistor is added to apply 4.4 V to the device. A user can easily REDUCE an operating current by choosing different RB values with minimized loss only in OIP3 and P1dB. R D =8.2 W C4=10 nF C3=100 pF C1=47 pF 2 mm RF IN L2=100 nH C2=100 pF ASL13W L1=27 nH RF OUT RB =5.6 kW S-parameters & K-factor 30 0 25 S11 (dB) Gain (dB) -5 20 15 -10 10 -15 5 0 0 200 400 600 800 1000 -20 0 200 400 Frequency (MHz) 600 800 1000 Frequency (MHz) 0 5 -5 4 Stability Factor S22 (dB) -10 -15 -20 -25 3 2 1 -30 -35 0 200 400 600 800 1000 0 0 500 Frequency (MHz) 5/14 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 April 2012 ASL13W 5-3000 MHz MMIC Amplifier Frequency (MHz) APPLICATION CIRCUIT LTE 698~787 Magnitude S21 (dB) 19.8 Magnitude S11 (dB) -20 Magnitude S22 (dB) -13 Output P1dB (dBm) 22 1) 698 ~ 787 +5 V Output IP3 (dBm) 34.5 Noise Figure (dB) 0.75 Device Voltage (V) 5 Current (mA) 60 1) OIP3 is measured with two tones at an output power of +10 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vcc=5V Note: A shunt RB is a bias resistor requisite to operate ASL13W properly, while RD as a voltage drop resistor is added to apply 4.4 V to the device. A user can easily REDUCE an operating current by choosing different RB values with minimized loss only in OIP3 and P1dB. RD =8.2 W C4=10 nF C3=100 pF L2=100 nH C1=18 pF 2 mm RF IN ASL13W L1=12 nH C2=100 pF RF OUT RB =5.6 kW S-parameters & K-factor 25 0 -5 20 -10 S11 [dB] S21 [dB] 15 10 -15 -20 5 0 400 -25 500 600 700 800 900 1000 -30 400 500 600 Frequency [MHz] 5 -5 4 Stability Factor 0 S22 [dB] -10 -15 -20 -25 400 800 900 1000 3 2 1 500 600 700 800 900 1000 0 0 500 Frequency [MHz] 6/14 700 Frequency [MHz] 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 April 2012 ASL13W 5-3000 MHz MMIC Amplifier APPLICATION CIRCUIT CDMA & GSM Frequency (MHz) 824 Magnitude S21 (dB) 19.5 Magnitude S11 (dB) -20 Magnitude S22 (dB) -14 -15 -15 Output P1dB (dBm) 824 ~ 960 +5 V 894 890 960 19 19 18.5 -20 -20 -18 -16 22 22 Output IP31) (dBm) 35 35.5 Noise Figure (dB) 0.9 0.95 Device Voltage (V) 5 5 Current (mA) 60 60 1) OIP3 is measured with two tones at an output power of +10 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vcc=5V Note: A shunt RB is a bias resistor requisite to operate ASL13W properly, while RD as a voltage drop resistor is added to apply 4.4 V to the device. A user can easily REDUCE an operating current by choosing different RB values with minimized loss only in OIP3 and P1dB. R D =8.2 W C4=10 nF C3=100 pF L2=100 nH C1=12 pF 2 mm RF IN ASL13W L1=10 nH C2=100 pF RF OUT RB =5.6 kW 30 0 25 -5 20 -10 S11 (dB) Gain (dB) S-parameters & K-factor 15 10 -40oc 25oc 85oc 5 0 600 700 800 900 1000 1100 -15 -20 -40oc 25oc 85oc -25 1200 -30 600 700 800 Frequency (MHz) -5 Stability Factor S22 (dB) 1100 1200 4 -40oc 25oc 85oc -10 -15 -20 3 2 1 -25 700 800 900 1000 1100 1200 0 0 500 Frequency (MHz) 7/14 1000 5 0 -30 600 900 Frequency (MHz) 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 April 2012 ASL13W 5-3000 MHz MMIC Amplifier Gain vs. Temperature Current vs. Temperature 100 21 80 20 Gain (dB) 22 Current (mA) 120 60 19 40 18 20 17 0 -60 -40 -20 0 20 40 60 80 Frequency = 900 MHz 16 -60 100 -40 -20 0 Temperature (oC) 60 26 50 24 40 Output IP3 (dBm) P1dB (dBm) 28 22 20 16 -60 Frequency = 900 MHz -20 0 60 80 100 30 20 20 40 60 80 -40oc 25oc 85oc 10 0 -40 40 Output IP3 vs. Tone Power (Frequency = 900 MHz) P1dB vs. Temperature 18 20 Temperature (oC) 100 4 5 6 Temperature (oC) 7 8 9 10 11 12 13 14 15 16 17 18 Pout per Tone (dBm) NF vs. Temperature (Frequency = 850MHz) 1.1 1.0 NF (dB) 0.9 0.8 0.7 0.6 Frequency = 850 MHz 0.5 0.4 -60 -40 -20 0 20 40 60 80 100 Temperature (oC) 8/14 ASB Inc. · [email protected] · Tel: +82-42-528-7223 April 2012 ASL13W 5-3000 MHz MMIC Amplifier APPLICATION CIRCUIT WCDMA Frequency (MHz) 1920 1980 2110 2170 Magnitude S21 (dB) Magnitude S11 (dB) 13.2 13 12.3 12.2 -20 -20 -18 -17 Magnitude S22 (dB) -15 -15 -15 Output P1dB (dBm) 1920 ~ 2170 +5 V 22 -15 22 Output IP31) (dBm) 38 38 Noise Figure (dB) 0.9 0.95 Device Voltage (V) 5 5 Current (mA) 60 60 1) OIP3 is measured with two tones at an output power of +10 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vcc=5V Note: A shunt RB is a bias resistor requisite to operate ASL13W properly, while RD as a voltage drop resistor is added to apply 4.4 V to the device. A user can easily REDUCE an operating current by choosing different RB values with minimized loss only in OIP3 and P1dB. RD =8.2 W C5=10 nF C4=100 pF L2=100 nH C2=68 pF 5 mm RF IN L1=39 nH C1=1 pF RB =5.6 kW ASL13W C3=68 pF RF OUT 25 0 20 -5 -10 15 S11 (dB) Gain (dB) S-parameters & K-factor 10 -15 -20 5 -25 0 1700 1800 1900 2000 2100 2200 -30 1700 1800 1900 Frequency (MHz) 5 -5 4 Stability Factor 0 S22 (dB) -10 -15 -20 -25 1700 2100 2200 3 2 1 1800 1900 2000 2100 2200 0 0 500 Frequency (MHz) 9/14 2000 Frequency (MHz) 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 April 2012 ASL13W 5-3000 MHz MMIC Amplifier NF vs. Temperature 1.1 1.0 NF (dB) 0.9 0.8 0.7 0.6 Frequency = 2000 MHz 0.5 0.4 -60 -40 -20 0 20 40 60 80 100 Temperature (oC) 10/14 ASB Inc. · [email protected] · Tel: +82-42-528-7223 April 2012 ASL13W 5-3000 MHz MMIC Amplifier Frequency (MHz) APPLICATION CIRCUIT 350 430 500 Magnitude S21 (dB) 24 23 22.5 Magnitude S11 (dB) -15 -15 -15 Magnitude S22 (dB) -18 -18 -20 Output P1dB (dBm) 21 21.5 21.5 350 ~ 500 Output IP31) (dBm) 33 34 34.5 +5 V Noise Figure (dB) 0.85 0.85 0.85 Device Voltage (V) 5 5 5 Current (mA) 60 60 60 1) OIP3 is measured with two tones at an output power of +10 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vcc=5V Note: A shunt RB is a bias resistor requisite to operate ASL13W properly, while RD as a voltage drop resistor is added to apply 4.4 V to the device. A user can easily REDUCE an operating current by choosing different RB values with minimized loss only in OIP3 and P1dB. RD =8.2 W C4=10 nF C3=100 pF L1=100 nH C1=82 pF 2 mm RF IN C2=82 pF ASL13W L2=39 nH RF OUT RB =5.6 kW S-parameters & K-factor 30 0 25 S11 (dB) Gain (dB) -5 20 15 10 -10 -15 5 0 0 200 400 600 800 1000 -20 0 200 400 Frequency (MHz) 600 800 1000 Frequency (MHz) 0 5 -5 4 Stability Factor S22 (dB) -10 -15 -20 2 1 -25 -30 3 0 200 400 600 800 1000 0 0 500 Frequency (MHz) 11/14 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 April 2012 ASL13W 5-3000 MHz MMIC Amplifier APPLICATION CIRCUIT Frequency (MHz) 960 1200 Magnitude S21 (dB) 18.5 17 Magnitude S11 (dB) -15 -15 Magnitude S22 (dB) -15 -17 Output P1dB (dBm) 22 22 960 ~ 1200 Output IP3 (dBm) 35.5 37 +5 V Noise Figure (dB) 0.95 0.9 Device Voltage (V) 5 5 Current (mA) 60 60 1) 1) OIP3 is measured with two tones at an output power of +10 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vcc=5V Note: A shunt RB is a bias resistor requisite to operate ASL13W properly, while RD as a voltage drop resistor is added to apply 4.4 V to the device. A user can easily REDUCE an operating current by choosing different RB values with minimized loss only in OIP3 and P1dB. RD =8.2 W C4=10 nF C3=100 pF L2=100 nH C1=6 pF 2 mm RF IN ASL13W L1=10 nH C2=100 pF RF OUT RB =5.6 kW 25 0 20 -5 15 -10 S11 (dB) Gain (dB) S-parameters & K-factor 10 5 0 600 -15 -20 800 1000 1200 1400 1600 -25 600 800 1000 Frequency (MHz) 1200 1400 1600 Frequency (MHz) 0 5 -5 4 Stability Factor S22 (dB) -10 -15 -20 2 1 -25 -30 600 3 800 1000 1200 1400 1600 0 0 500 Frequency (MHz) 12/14 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 April 2012 ASL13W 5-3000 MHz MMIC Amplifier Frequency (MHz) APPLICATION CIRCUIT 2300 2450 2600 Magnitude S21 (dB) 12 11.5 11 Magnitude S11 (dB) -20 -20 -18 Magnitude S22 (dB) -16 -16 -15 Output P1dB (dBm) 22 22 22 2300 ~ 2600 Output IP3 (dBm) 38 37.5 37.5 +5 V Noise Figure (dB) 1.0 1.1 1.15 Device Voltage (V) 5 5 5 Current (mA) 60 60 60 1) 1) OIP3 is measured with two tones at an output power of +10 dBm/tone separated by 1 MHz. 2 Board Layout (FR4, 40x40 mm , 0.8T) Schematic Vcc=5V Note: A shunt RB is a bias resistor requisite to operate ASL13W properly, while RD as a voltage drop resistor is added to apply 4.4 V to the device. A user can easily REDUCE an operating current by choosing different RB values with minimized loss only in OIP3 and P1dB. RD =8.2 W C5=10 nF C4=100 pF RF IN L2=39 nH C2=68 pF L1=39 nH C1=1 pF ASL13W RB =5.6 kW C3=68 pF RF OUT S-parameters & K-factor 20 0 -5 15 S11 (dB) Gain (dB) -10 10 -40oc 25oc 85oc 5 0 1800 2000 2200 2400 2600 2800 -15 -20 -40oc 25oc 85oc -25 3000 -30 1800 2000 2200 Frequency (MHz) 0 5 -5 4 Stability Factor S22 (dB) -10 -15 -40oc 25oc 85oc -20 -25 1800 2000 2200 2400 2600 2600 2800 3000 2800 3 2 1 3000 0 0 500 Frequency (MHz) 13/14 2400 Frequency (MHz) 1000 1500 2000 2500 3000 3500 Frequency (MHz) ASB Inc. · [email protected] · Tel: +82-42-528-7223 April 2012 ASL13W 5-3000 MHz MMIC Amplifier Gain vs. Temperature 100 20 80 16 60 12 Gain (dB) Current (mA) Current vs. Temperature 40 Frequency = 2450 MHz 4 20 0 -60 8 -40 -20 0 20 40 60 80 0 -60 100 -40 -20 60 80 100 50 Output IP3 (dBm) 24 P1dB (dBm) 40 60 26 22 20 Frequency = 2450 MHz 18 40 30 20 10 0 -40 -20 0 20 40 60 80 -40oc 25oc 85oc 100 6 7 8 Temperature (oC) 14/14 20 Output IP3 vs. Tone Power (Frequency = 2450 MHz) P1dB vs. Temperature 16 -60 0 Temperature (oC) Temperature (oC) 9 10 11 12 13 14 15 16 17 Pout per Tone (dBm) ASB Inc. · [email protected] · Tel: +82-42-528-7223 April 2012