CY7C67300 EZ-Host™ Programmable Embedded USB Host and Peripheral Controller with Automotive AEC Grade Support EZ-Host Features ■ Single chip programmable USB dual-role (Host/Peripheral) controller with two configurable Serial Interface Engines (SIEs) and four USB ports ■ Support for USB On-The-Go (OTG) protocol ■ On-chip 48 MHz 16-bit processor with dynamically switchable clock speed ■ On-chip 16-bit DMA/mailbox data path interface ■ Supports 12 MHz external crystal or clock ■ 3.3V operation ■ Automotive AEC grade option (–40°C to 85°C) ■ Package option—100-pin TQFP ■ Configurable IO block supporting a variety of IO options or up to 32 bits of General Purpose IO (GPIO) Typical Applications ■ 4K x 16 internal masked ROM containing built in BIOS that supports a communication ready state with access to I2C™ EEPROM Interface, external ROM, UART, or USB EZ-Host is a very powerful and flexible dual role USB controller that supports a wide variety of applications. It is primarily intended to enable host capability in applications such as: ■ 8K x 16 internal RAM for code and data buffering ■ Set top boxes ■ Extended memory interface port for external SRAM and ROM ■ Printers ■ 16-bit parallel Host Port Interface (HPI) with a DMA/mailbox data path for an external processor to directly access all of the on-chip memory and control on-chip SIEs ■ KVM switches ■ Kiosks ■ Automotive applications ■ Wireless access points ■ Fast serial port supports from 9600 baud to 2.0M baud ■ SPI support in both master and slave CY7C67300 Block Diagram CY7C67300 Timer 0 Control Timer 1 UART I/F I2C EEPROM I/F Watchdog CY16 16-bit RISC CORE HSS I/F Vbus, ID OTG D+,D- PWM USB-A SIE1 Host/ Peripheral USB Ports D+,D- USB-B D+,D- USB-A SPI I/F IDE I/F SIE2 4Kx16 ROM BIOS 8Kx16 RAM SHARED INPUT/OUTPUT PINS nRESET GPIO [31:0] HPI I/F USB-B D+,D- GPIO X1 X2 Mobile Power Booster PLL External MEM I/F (SRAM/ROM) SHARED INPUT/OUTPUT PINS A[15:0] D[15:0] Cypress Semiconductor Corporation Document #: 38-08015 Rev. *K • 198 Champion Court • CTRL[9:0] San Jose, CA 95134-1709 • 408-943-2600 Revised July 5, 2011 [+] Feedback CY7C67300 Contents Introduction ....................................................................... 3 Functional Overview ........................................................ 3 Processor Core ........................................................... 3 Clocking ....................................................................... 3 Memory ....................................................................... 3 Interrupts ..................................................................... 3 General Timers and Watchdog Timer ......................... 3 Power Management .................................................... 3 Interface Descriptions ...................................................... 3 USB Interface .............................................................. 4 OTG Interface .............................................................. 5 External Memory Interface .......................................... 6 General Purpose IO Interface (GPIO) ......................... 8 UART Interface ............................................................ 8 I2C EEPROM Interface ............................................... 8 Serial Peripheral Interface ........................................... 8 High-Speed Serial Interface ........................................ 9 Programmable Pulse/PWM Interface .......................... 9 Host Port Interface .................................................... 10 IDE Interface ............................................................. 10 Charge Pump Interface ............................................. 11 Booster Interface ....................................................... 12 Crystal Interface ........................................................ 12 Boot Configuration Interface ...................................... 13 Operational Modes .................................................... 13 Power Savings and Reset Description ........................ 14 Power Saving Mode Description ............................... 14 Sleep ......................................................................... 14 External (Remote) Wakeup Source ........................... 15 Power-On-Reset Description ..................................... 15 Reset Pin ................................................................... 15 USB Reset ................................................................. 15 Memory Map .................................................................... 15 Mapping ..................................................................... 15 Registers ......................................................................... 17 Processor Control Registers ..................................... 17 External Memory Registers ....................................... 24 Timer Registers ......................................................... 26 General USB Registers ............................................. 28 USB Host Only Registers .......................................... 30 USB Device Only Registers ...................................... 39 Document #: 38-08015 Rev. *K OTG Control Registers .............................................. 49 GPIO Registers ......................................................... 50 IDE Registers ............................................................ 53 HSS Registers ........................................................... 56 HPI Registers ............................................................ 62 SPI Registers ............................................................ 66 UART Registers ........................................................ 74 PWM Registers ......................................................... 76 Pin Diagram ..................................................................... 80 Pin Descriptions ............................................................. 80 Absolute Maximum Ratings .......................................... 84 Operating Conditions ..................................................... 84 Crystal Requirements (XTALIN, XTALOUT) ................. 84 DC Characteristics ......................................................... 84 USB Transceiver ....................................................... 85 AC Timing Characteristics ............................................. 86 Reset Timing ........................................................... 86 Clock Timing ............................................................. 86 SRAM Read Cycle[15] .............................................. 87 SRAM Write Cycle [17] .............................................. 88 I2C EEPROM Timing-Serial IO ................................. 89 HPI (Host Port Interface) Write Cycle Timing ........... 90 HPI (Host Port Interface) Read Cycle Timing ........... 91 IDE Timing ................................................................. 92 HSS BYTE Mode Transmit ........................................ 92 HSS Block Mode Transmit ........................................ 92 HSS BYTE and BLOCK Mode Receive .................... 92 Hardware CTS/RTS Handshake ............................... 93 Register Summary .......................................................... 93 Ordering Information ...................................................... 98 Ordering Code Definitions ......................................... 98 Package Diagram ............................................................ 99 Acronyms ...................................................................... 100 Document Conventions ............................................... 100 Units of Measure ..................................................... 100 Document History Page ............................................... 101 Sales, Solutions, and Legal Information .................... 102 Worldwide Sales and Design Support ..................... 102 Products .................................................................. 102 PSoC Solutions ....................................................... 102 Page 2 of 102 [+] Feedback CY7C67300 Introduction Interrupts EZ-Host™ (CY7C67300) is Cypress Semiconductor’s first full-speed, low cost multiport host/peripheral controller. EZ-Host is designed to easily interface to most high performance CPUs to add USB host functionality. EZ-Host has its own 16-bit RISC processor to act as a coprocessor or operate in standalone mode. EZ-Host also has a programmable IO interface block allowing a wide range of interface options. EZ-Host provides 128 interrupt vectors. The first 48 vectors are hardware interrupts and the following 80 vectors are software interrupts. General Timers and Watchdog Timer EZ-Host has two built in programmable timers and a Watchdog timer. All three timers can generate an interrupt to the EZ-Host. Power Management Functional Overview An overview of the processor core components are presented in this section. EZ-Host has one main power saving mode, Sleep. Sleep mode pauses all operations and provides the lowest power state. Interface Descriptions Processor Core EZ-Host has a wide variety of interface options for connectivity. With several interface options available, EZ-Host can act as a seamless data transport between many different types of devices. EZ-Host has a general purpose 16-bit embedded RISC processor that runs at 48 MHz. Clocking EZ-Host requires a 12 MHz source for clocking. Either an external crystal or TTL level oscillator may be used. EZ-Host has an internal PLL that produces a 48 MHz internal clock from the 12 MHz source. Memory EZ-Host has a built in 4K × 16 masked ROM and an 8K × 16 internal RAM. The masked ROM contains the EZ-Host BIOS. The internal RAM can be used for program code or data. See Table 1 and Table 2 on page 4 to understand how the interfaces share pins and which can coexist. Note that some interfaces have more then one possible port location selectable through the GPIO control register [0xC006]. General guidelines for interfaces are as follows: ■ HPI and IDE interfaces are mutually exclusive. ■ If 16-bit external memory is required, then HSS and SPI default locations must be used. ■ I2C EEPROM and OTG do not conflict with any interfaces. Table 1. Interface Options for GPIO Pins GPIO Pins GPIO31 GPIO30 GPIO29 GPIO28 GPIO27 GPIO26 GPIO25 GPIO24 GPIO23 GPIO22 GPIO21 GPIO20 GPIO19 GPIO18 GPIO17 GPIO16 GPIO15 GPIO14 GPIO13 GPIO12 GPIO11 HPI IDE PWM HSS SPI UART I2C SCL/SDA SCL/SDA OTG OTGID TX RX INT nRD nWR nCS A1 A0 PWM3 CTS[1] PWM2 PWM1 PWM0 RTS[1] RXD[1] TXD[1] IOREADY IOR IOW D15 D14 D13 D12 D11 CS1 CS0 A2 A1 A0 D15 D14 D13 D12 D11 MOSI[1] Note 1. Default interface location. Document #: 38-08015 Rev. *K Page 3 of 102 [+] Feedback CY7C67300 Table 1. Interface Options for GPIO Pins (continued) GPIO Pins GPIO10 GPIO9 GPIO8 GPIO7 GPIO6 GPIO5 GPIO4 GPIO3 GPIO2 GPIO1 GPIO0 HPI D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 IDE D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 PWM HSS SPI SCK[1] nSSI[1] MISO[1] UART I2C OTG HSS CTS[2] RTS[2] RXD[2] TXD[2] SPI UART I2C OTG Table 2. Interface Options for External Memory Bus Pins MEM Pins D15 D14 D13 D12 D11 D10 D9 D8 D[7:0] A[18:0] CONTROL HPI IDE PWM MOSI[2] SCK[2] nSSI[2] MISO[2] USB Interface EZ-Host has two built in Host/Peripheral SIEs and four USB transceivers that meet the USB 2.0 specification requirements for full and low speed (high speed is not supported). In Host mode, EZ-Host supports four downstream ports, each support control, interrupt, bulk, and isochronous transfers. In Peripheral mode, EZ-Host supports one peripheral port with eight endpoints for each of the two SIEs. Endpoint 0 is dedicated as the control endpoint and only supports control transfers. Endpoints 1 though 7 support interrupt, bulk (up to 64 bytes/packet), or isochronous transfers (up to 1023 Bytes/packet size). EZ-Host also supports a combination of Host and Peripheral ports simultaneously as shown in Table 3. Table 3. USB Port Configuration Options Port Configurations OTG Port 1A Port 1B Port 2A Port 2B OTG – – – OTG + 2 Hosts OTG – Host Host OTG + 1 Host OTG – Host – OTG + 1 Host OTG – – Host OTG + 1 Peripheral OTG – Peripheral – OTG + 1 Peripheral OTG – – Peripheral 4 Hosts Host Host Host Host 3 Hosts Any Combination of Ports 2 Hosts Any Combination of Ports 1 Host Any Port Note 2. Alternate interface location. Document #: 38-08015 Rev. *K Page 4 of 102 [+] Feedback CY7C67300 Table 3. USB Port Configuration Options (continued) Port Configurations Port 1A Port 1B Port 2A Port 2B 2 Hosts + 1 Peripheral Host Host Peripheral – 2 Hosts + 1 Peripheral Host Host – Peripheral 2 Hosts + 1 Peripheral Peripheral – Host Host 2 Hosts + 1 Peripheral – Peripheral Host Host 1 Host + 1 Peripheral Host – Peripheral – 1 Host + 1 Peripheral Host – – Peripheral 1 Host + 1 Peripheral – Host – Peripheral 1 Host + 1 Peripheral – Host Peripheral – 1 Host + 1 Peripheral Peripheral – Host – 1 Host + 1 Peripheral Peripheral – – Host 1 Host + 1 Peripheral – Peripheral – Host 1 Host + 1 Peripheral – Peripheral Host – 2 Peripherals Peripheral – Peripheral – 2 Peripherals Peripheral – – Peripheral 2 Peripherals – Peripheral – Peripheral 2 Peripherals – Peripheral Peripheral – 1 Peripheral Any Port USB Features OTG Interface ■ USB 2.0-compliant for full and low speed ■ Up to four downstream USB host ports ■ Up to two upstream USB peripheral ports EZ-Host has one USB port that is compatible with the USB On-The-Go supplement to the USB 2.0 specification. The USB OTG port has a various hardware features to support Session Request Protocol (SRP) and Host Negotiation Protocol (HNP). OTG is only supported on USB PORT 1A. ■ Configurable endpoint buffers (pointer and length), must reside in internal RAM ■ Up to eight available peripheral endpoints (one control endpoint) ■ Supports control, interrupt, bulk, and isochronous transfers ■ Internal DMA channels for each endpoint ■ Internal pull up and pull down resistors ■ Internal series termination resistors on USB data lines USB Pins Table 4. USB Interface Pins Pin Name DM1A DP1A DM1B DP1B DM2A DP2A DM2B DP2B Document #: 38-08015 Rev. *K Pin Number 22 23 18 19 9 10 4 5 OTG Features ■ Internal charge pump to supply and control VBUS ■ VBUS valid status (above 4.4V) ■ VBUS status for 2.4V< VBUS <0.8V ■ ID pin status ■ Switchable 2K ohm internal discharge resistor on VBUS ■ Switchable 500 ohm internal pull up resistor on VBUS ■ Individually switchable internal pull up and pull down resistors on the USB data lines OTG Pins Table 5. OTG Interface Pins Pin Name DM1A DP1A OTGVBUS OTGID CSwitchA CSwitchB Pin Number 22 23 11 41 13 12 Page 5 of 102 [+] Feedback CY7C67300 External Memory Interface Merge Mode EZ-Host provides a robust interface to a wide variety of external memory arrays. All available external memory array locations can contain either code or data. The CY16 RISC processor directly addresses a flat memory space from 0x0000 to 0xFFFF. Merge modes enabled through the External Memory Control register [0xC03A] allow combining of external memory regions in accordance with the following: External Memory Interface Features ■ Supports 8-bit or 16-bit SRAM or ROM ■ SRAM or ROM can be used for code or data space ■ Direct addressing of SRAM or ROM ■ Two external memory mapped page registers External Memory Access Strobes ■ nXMEMSEL is active from 0x8000 to 0xBFFF ■ nXRAMSEL is active from 0x4000 to 0x7FFF when RAM Merge is disabled; nXRAMSEL is active from 0x4000 to 0xBFFF when RAM Merge is enabled ■ nXROMSEL is active from 0xC100 to 0xDFFF when ROM Merge is disabled; nXROMSEL is active from 0x8000 to 0xDFFF (excluding the 0xC000 to 0xC0FF area) when ROM Merge is enabled Program Memory Hole Description Access to external memory is sampled asynchronously on the rising edge of strobes with a minimum of one wait state cycle. Up to seven wait state cycles may be inserted for external memory access. Each additional wait state cycle stretches the external memory access time by 21 ns (you must be running in internal memory when changing wait states). An external memory device with 12 ns access time is necessary to support 48 MHz code execution. Page Registers EZ-Host allows extended data or program code to be stored in external SRAM, or ROM. The total size of extended memory can be up to 512K bytes. The CY16 processor can access extended memory via two address regions of 0x8000-0x9FFF and 0xA000-0xBFFF. The page register 0xC018 can be used to control the address region 0x8000-0x9FFF and the page register 0xC01A controls the address region of 0xA000-0xBFFF. Figure 1 illustrates that when the nXMEMSEL pin is asserted the upper CPU address pins are driven by the contents of the Page x registers. Code residing in the 0xC000-0xC0FF address space is not accessible by the CPU. DMA to External Memory Prohibited EZ-Host supports an internal DMA engine to rapidly move data between different functional blocks within the chip. This DMA engine is used for SIE1, SIE2, HPI, SPI, HSS, and IDE but it can only transfer data between the specified block and internal RAM or ROM. Setting up the DMA engine to transfer to or from an external memory space might result in internal RAM data corruption because the hardware (for example, HSS/HPI/SIE1/SIE2/IDE) does not explicitly check the address range. For example, setting up a DMA transfer to external address 0x8000 might result in a DMA transfer into address 0x0000. External Memory Related Resource Considerations: ■ By default A[18:15] are not available for general addressing and are driven high on power up. The Upper Address Enable register must be written appropriately to enable A[18:15] for general addressing purposes. ■ 47K ohm external pull up on pin A15 for 12 MHz crystal operation. ■ During the 3 ms BIOS boot procedure the CPU external memory bus is active. ■ ROM boot load value 0xC3B6 located at 0xC100. ■ HPI, HSS, SPI, SIE1, SIE2, and IDE cannot DMA to external memory arrays. ■ Page 1 banking is always enabled and is in effect from 0x8000 to 0x9FFF. ■ Page 2 banking is always enabled and is in effect from 0xA000 to 0xBFFF. ■ CPU memory bus strobes may wiggle when chip selects are inactive. Figure 1. Page n Registers External Address Pins Logic nXMEMSEL Pin 0000 + PC[14:0] 1 PAGEx Register[5:0] + PC[12:0] 0 A[18:0] Where: x = 1 or 2 PC = Program Counter A = CPU Address Bus Note: PAGE 1 Register Active Range = 8000h to 9FFFh PAGE 2 Register Active Range = A000h to BFFFh nXMEMSEL Pin Active Range = 8000h to BFFFh Document #: 38-08015 Rev. *K Page 6 of 102 [+] Feedback CY7C67300 External Memory Interface Pins Table 6. External Memory Interface Pins (continued) Table 6. External Memory Interface Pins Pin Name Pin Number Pin Name Pin Number D3 80 nWR 64 D2 81 nRD 62 D1 82 nXMEMSEL (optional nCS) 34 D0 83 nXROMSEL (ROM nCS) 35 nXRAMSEL (RAM nCS) 36 External Memory Interface Block Diagrams A18 95 A17 96 Figure 2 illustrates how to connect a 64k × 8 memory array (SRAM/ROM) to the EZ-Host external memory interface. A16 97 A15 38 A14 33 A13 32 A12 31 A11 30 A10 27 A9 25 A8 24 A7 20 A6 17 A5 8 A4 7 A3 3 A2 2 Figure 2. Interfacing to 64k × 8 Memory Array Interfacing to 64K x 8 External Memory Array EZ-Host CY7C67300 External Memory Array 64K x 8 A[15:0] D[7:0] nXRAMSEL nWR nRD A[15:0] D[7:0] CE WE OE Figure 3 illustrates the interface for connecting a 16-bit ROM or 16-bit RAM to the EZ-Host external memory interface. In 16-bit mode, up to 256K words of external ROM or RAM are supported. Note that the address lines do not map directly. A1 1 nBEL/A0 99 Figure 3. Interfacing up to 256k × 16 for External Code/Data nBEH 98 Up to 256k x 16 External Code/Data (Page Mode) D15 67 D14 68 D13 69 D12 70 D11 71 D10 72 D9 73 D8 74 D7 76 D6 77 D5 78 D4 79 Document #: 38-08015 Rev. *K EZ-Host CY7C67300 External Memory Array Up to 256k x 16 A[18:1] D[15:0] nXMEMSEL A[17:0] D[15:0] CE nBEL BLE nBEH nWR nRD BHE WE OE Page 7 of 102 [+] Feedback CY7C67300 Figure 4 illustrates the interface for connecting an 8-bit ROM or 8-bit RAM to the EZ-Host external memory interface. In 8-bit mode, up to 512K bytes of external ROM or RAM are supported. Figure 4. Interfacing up to 512k × 8 for External Code/Data Up to 512k x 8 External Code/Data (Page Mode) EZ-Host CY7C67300 External Memory Array Up to 512k x8 I2C EEPROM Interface EZ-Host provides a master-only I2C interface for external serial EEPROMs. The serial EEPROM can be used to store application specific code and data. Use the I2C interface for loading code out of EEPROM, it is not a general I2C interface. The I2C EEPROM interface is a BIOS implementation and is exposed through GPIO pins. Refer to the BIOS documentation for additional details on this interface. I2C EEPROM Features A[18:0] D[7:0] nXMEMSEL nWR nRD A[18:0] D[7:0] CE WE OE ■ Supports EEPROMs up to 64 KB (512K bit) ■ Auto-detection of EEPROM size I2C EEPROM Pins Table 8. I2C EEPROM Interface Pins Pin Name SCK SDA General Purpose IO Interface (GPIO) EZ-Host has up to 32 GPIO signals available. Several other optional interfaces use GPIO pins as well and may reduce the overall number of available GPIOs. SCK SDA Pin Number SMALL EEPROM 39 40 LARGE EEPROM 40 39 GPIO Number GPIO31 GPIO30 GPIO30 GPIO31 GPIO Description All Inputs are sampled asynchronously with state changes occurring at a rate of up to two 48 MHz clock cycles. GPIO pins are latched directly into registers, a single flip-flop. Unused Pin Descriptions Ensure to tristate unused USB pins with the D+ line pulled high through the internal pull up resistor and the D– line pulled low through the internal pull down resistor. Configure unused GPIO pins as outputs so they are driven low. Serial Peripheral Interface EZ-Host provides a SPI interface for added connectivity. EZ-Host may be configured as either an SPI master or SPI slave. The SPI interface can be exposed through GPIO pins or the External Memory port. SPI Features ■ Master or slave mode operation ■ DMA block transfer and PIO byte transfer modes UART Interface ■ Full duplex or half duplex data communication EZ-Host has a built in UART interface. The UART interface supports data rates from 900 to 115.2K baud. It can be used as a development port or for other interface requirements. The UART interface is exposed through GPIO pins. ■ 8-byte receive FIFO and 8-byte transmit FIFO ■ Selectable master SPI clock rates from 250 kHz to 12 MHz ■ Selectable master SPI clock phase and polarity UART Features ■ Slave SPI signaling synchronization and filtering ■ Supports baud rates of 900 to 115.2K ■ Slave SPI clock rates up to 2 MHz ■ 8-N-1 ■ Maskable interrupts for block and byte transfer modes ■ Individual bit transfer for non-byte aligned serial communication in PIO mode ■ Programmable delay timing for the active/inactive master SPI clock ■ Auto or manual control for master mode slave select signal ■ Complete access to internal memory UART Pins. Table 7. UART Interface Pins Pin Name Pin Number TX 42 RX 43 Document #: 38-08015 Rev. *K Page 8 of 102 [+] Feedback CY7C67300 SPI Pins HSS Pins The SPI port has a few different pin location options as shown in Table 9. The port location is selectable via the GPIO control register [0xC006]. The HSS port has a few different pin location options as shown in Table 10. The port location is selectable via the GPIO control register [0xC006]. Table 9. SPI Interface Pins Table 10. HSS Interface Pins Pin Name Pin Name Pin Number Pin Number Default Location Default Location CTS 44 nSSI 56 or 65 SCK 61 RTS 53 MOSI 60 RXD 54 MISO 66 TXD 55 Alternate Location Alternate Location 73 CTS 67 SCK 72 RTS 68 MOSI 71 RXD 69 74 TXD 70 nSSI MISO High-Speed Serial Interface Programmable Pulse/PWM Interface EZ-Host provides an HSS interface. The HSS interface is a programmable serial connection with baud rate from 9600 baud to 2.0M baud. The HSS interface supports both byte and block mode operations and also hardware and software handshaking. Complete control of EZ-Host can be accomplished through this interface via an extensible API and communication protocol. The HSS interface can be exposed through GPIO pins or the External Memory port. EZ-Host has four built in PWM output channels. Each channel provides a programmable timing generator sequence that can be used to interface to various image sensors or other applications. The PWM interface is exposed through GPIO pins. Programmable Pulse/PWM Features ■ Four independent programmable waveform generators ■ Programmable predefined frequencies ranging from 5.90 KHz to 48 MHz HSS Features ■ 8 bits, no parity code ■ Configurable polarity ■ Programmable baud rate from 9600 baud to 2M baud ■ Continuous and one-shot mode available ■ Selectable 1- or 2-stop bit on transmit Programmable Pulse/PWM Pins. ■ Programmable inter-character gap timing for Block Transmit Table 11. PWM Interface Pins ■ 8-byte receive FIFO Pin Name Pin Number ■ Glitch filter on receive PWM3 44 ■ Block mode transfer directly to/from EZ-Host internal memory (DMA transfer) PWM2 53 PWM1 54 ■ Selectable CTS/RTS hardware signal handshake protocol PWM0 55 ■ Selectable XON/XOFF software handshake protocol ■ Programmable Receive interrupt, Block Transfer Done interrupts ■ Complete access to internal memory Document #: 38-08015 Rev. *K Page 9 of 102 [+] Feedback CY7C67300 Table 12. HPI Interface Pins (continued)[3, 4] Host Port Interface EZ-Host has an HPI interface. The HPI interface provides DMA access to the EZ-Host internal memory by an external host, plus a bidirectional mailbox register for supporting high level communication protocols. This port is designed to be the primary high-speed connection to a host processor. Complete control of EZ-Host can be accomplished through this interface via an extensible API and communication protocol. Other than the hardware communication protocols, a host processor has identical control over EZ-Host whether connecting to the HPI or HSS port. The HPI interface is exposed through GPIO pins. HPI Features D11 60 D10 61 D9 65 D8 66 D7 86 D6 87 D5 89 D4 90 D3 91 ■ 16-bit data bus interface D2 92 ■ 16 MB/s throughput D1 93 ■ Auto-increment of address pointer for fast block mode transfers D0 94 ■ Direct memory access (DMA) to internal memory ■ Bidirectional Mailbox register The two HPI address pins are used to address one of four possible HPI port registers as shown in Table 13. ■ Byte swapping Table 13. HPI Addressing ■ Complete access to internal memory HPI A[1:0] A1 A0 ■ Complete control of SIEs through HPI HPI Data 0 0 ■ Dedicated HPI status register HPI Pins HPI Mailbox 0 1 HPI Address 1 0 HPI Status 1 1 Table 12. HPI Interface Pins [3, 4] Pin Name Pin Number INT 46 nRD 47 nWR 48 nCS 49 A1 50 A0 52 D15 56 D14 57 D13 58 D12 59 IDE Interface EZ-Host has an IDE interface. The IDE interface supports PIO mode 0-4 as specified in the Information Technology-AT Attachment–4 with Packet Interface Extension (ATA/ATAPI-4) Specification, T13/1153D Rev 18. There is no need for firmware to use programmable wait states. The CPU read/write cycle is automatically extended as needed for direct CPU to IDE read/write accesses. The EZ-Host IDE interface also has a BLOCK transfer mode that allows EZ-Host to read/write large blocks of data to/from the IDE data register and move it to/from the EZ-Host on-chip memory directly without intervention of the CPU. The IDE interface is exposed through GPIO pins. Table 14 on page 11 lists the achieved throughput for maximum block mode data transfer rate (with IDE_IORDY true) for the various IDE PIO modes. Notes 3. HPI_INT is for the Outgoing Mailbox interrupt. 4. HPI strobes are negative logic sampled on rising edge. Document #: 38-08015 Rev. *K Page 10 of 102 [+] Feedback CY7C67300 Table 14. IDE Throughput ATA/ATAPI-4 Min Cycle Time PIO Mode 0 600 ns PIO Mode 1 383 ns PIO Mode 2 240 PIO Mode 3 180 ns PIO Mode 4 120 ns T = System clock period = 1/48 MHz. Mode Actual Min Cycle Time 30T = 625 ns 20T = 416.7 ns 13T = 270.8 ns 10T = 208.3 ns 8T = 166.7 ns ATA/ATPI-4 Max Transfer Rate 3.33 MB/s 5.22 MB/s 8.33 MB/s 11.11 MB/s 16.67 MB/s Actual Max Transfer Rate 3.2 MB/s 4.8 MB/s 7.38 MB/s 9.6 MB/s 12.0 MB/s IDE Features Charge Pump Interface ■ Programmable IO mode 0–4 ■ Block mode transfers ■ Direct memory access to/from internal memory through the IDE data register VBUS for the USB OTG port can be produced by EZ-Host using its built in charge pump and some external components. Ensure the circuit connections look similar to the following diagram. Figure 5. Charge Pump IDE Pins D1 Table 15. IDE Interface Pins D2 CSWITCHA CY7C67300 Pin Name Pin Number IORDY 46 CSWITCHB C1 VBUS OTGVBUS IOR 47 IOW 48 CS1 50 CS0 52 Component details: A2 53 ■ A1 54 D1 and D2: Schottky diodes with a current rating greater than 60 mA A0 55 ■ C1: Ceramic capacitor with a capacitance of 0.1 µF D15 56 ■ D14 57 D13 58 C2: Make capacitor value no more that 6.5 µF since that is the maximum capacitance allowed by the USB OTG specifications for a dual role device. The minimum value of C2 is 1 µF. There are no restrictions on the type of capacitor for C2. D12 59 D11 60 D10 61 D9 65 D8 66 D7 86 D6 87 D5 89 Pin Name Pin Number D4 90 OTGVBUS 11 D3 91 CSwitchA 13 D2 92 CSwitchB 12 D1 93 D0 94 Document #: 38-08015 Rev. *K C2 If the VBUS charge pump circuit is not to be used, CSWITCHA, CSWITCHB, and OTGVBUS can be left unconnected. Charge Pump Features ■ Meets OTG Supplement Requirements, see Table 134 on page 85 for details. Charge Pump Pins Table 16. Charge Pump Interface Pins Page 11 of 102 [+] Feedback CY7C67300 Booster Interface Booster Pins EZ-Host has an on chip power booster circuit for use with power supplies that range between 2.7V and 3.6V. The booster circuit boosts the power to 3.3V nominal to supply power for the entire chip. The booster circuit requires an external inductor, diode, and capacitor. During power down mode, the circuit is disabled to save power. Figure 6 shows how to connect the booster circuit. Table 17. Charge Pump Interface Pins Figure 6. Power Supply Connection With Booster Crystal Interface BOOSTVcc L1 2.7V to 3.6V Power Supply VSWITCH Pin Name Pin Number BOOSTVcc 16 VSWITCH 14 The recommended crystal circuit to be used with EZ-Host is shown in Figure 8 If an oscillator is used instead of a crystal circuit, connect it to XTALIN and leave XTALOUT unconnected. For further information about the crystal requirements, see Table 132 on page 84. Noted that the CLKSEL pin (pin 38) is sampled after reset to determine what crystal or clock source frequency is used. For normal operation, 12 MHz is required so the CLKSEL pin must have a 47K ohm pull up resistor to VCC.. Figure 8. Crystal Interface D1 3.3V VCC AVCC XTALIN C1 CY7C67300 Y1 Component details: ■ L1: Inductor with inductance of 10 µH and a current rating of at least 250 mA ■ D1: Schottky diode with a current rating of at least 250 mA ■ C1: Tantalum or ceramic capacitor with a capacitance of at least 2.2 µF XTALOUT C1 = 22 pF 12MHz Parallel Resonant Fundamental Mode 500uW 20-33pf ±5% C2 = 22 pF Figure 7 shows how to connect the power supply when the booster circuit is not being used. Figure 7. Power Supply Connection Without Booster Crystal Pins Table 18. Crystal Pins BOOSTVcc 3.0V to 3.6V Power Supply Pin Name Pin Number XTALIN 29 XTALOUT 28 VSWITCH VCC AVCC Document #: 38-08015 Rev. *K Page 12 of 102 [+] Feedback CY7C67300 Boot Configuration Interface Operational Modes EZ-Host can boot into any one of four modes. The mode it boots into is determined by the TTL voltage level of GPIO[31:30] at the time nRESET is deasserted. Table 19 shows the different boot pin combinations possible. After a reset pin event occurs, the BIOS bootup procedure executes for up to 3 ms. GPIO[31:30] are sampled by the BIOS during bootup only. After bootup these pins are available to the application as GPIOs. The operational modes are discussed in the following sections. Table 19. Boot Configuration Interface GPIO31 (Pin 39) GPIO30 (Pin 40) 0 0 Host Port Interface (HPI) 0 1 High-Speed Serial (HSS) 1 0 Serial Peripheral Interface (SPI, slave mode) 1 1 I2C EEPROM (Standalone Mode) Boot Mode Ensure that GPIO[31:30] is pulled high or low as needed using resistors tied to VCC or GND with resistor values between 5K ohms and 15K ohms. Do not tie GPIO[31:30] directly to VCC or GND. Note that in standalone mode, the pull ups on those two pins are used for the serial I2C EEPROM (if implemented). Make sure that the resistors used for these pull ups conform to the serial EEPROM manufacturer's requirements. If any mode other then standalone is chosen, EZ-Host is in coprocessor mode. The device powers up with the appropriate communication interface enabled according to its boot pins and waits idle until a coprocessor communicates with it. See the BIOS documentation for greater detail of the boot process. Document #: 38-08015 Rev. *K Coprocessor Mode EZ-Host can act as a coprocessor to an external host processor. In this mode, an external host processor drives EZ-Host and is the main processor rather then EZ-Host’s own 16-bit internal CPU. An external host processor may interface to EZ-Host through one of the following three interfaces in coprocessor mode: ■ HPI mode, a 16 bit parallel interface with up to 16 MB transfer rate ■ HSS mode, a serial interface with up to 2M baud transfer rate ■ SPI mode, a serial interface with up to 2 Mb/s transfer rate At bootup GPIO[31:30] determine which of these three interfaces are used for coprocessor mode. See Table 19 for details. Bootloading begins from the selected interface after POR + 3 ms of BIOS bootup. Standalone Mode In standalone mode, there is no external processor connected to EZ-Host. Instead, EZ-Host’s own internal 16-bit CPU is the main processor and firmware is typically downloaded from an EEPROM. Optionally, firmware may also be downloaded via USB. See Table 19 for booting into standalone mode. After booting into standalone mode (GPIO[31:30] = ‘11’), the following pins are affected: ■ GPIO[31:30] are configured as output pins to examine the EEPROM contents ■ GPIO[28:27] are enabled for debug UART mode ■ GPIO[29] is configured for as OTGID for OTG applications on PORT1A ❐ If OTGID is logic 1 then PORT1A (OTG) is configured as a USB peripheral ❐ If OTGID is logic 0 then PORT1A (OTG) is configured as a USB host ■ Ports 1B, 2A, and 2B default as USB peripheral ports ■ All other pins remain INPUT pins. Page 13 of 102 [+] Feedback CY7C67300 Minimum Hardware Requirements for Standalone Mode – Peripheral Only Figure 9. Minimum Standalone Hardware Configuration – Peripheral Only EZ-Host CY7C67300 VCC, AVCC, BoostVCC VReg VBus D+ Standard-B or Mini-B Reset Logic nRESET DPlus DMinus DGND SHIELD VCC Bootstrap Options 47Kohm Vcc Vcc Pin 38 10k 10k GPIO[30] SCL* GPIO[31] SDA* Int. 16k x8 Code / Data VCC A0 A1 Up to 64k x8 EEPROM Bootloading Firmware VCC WP A2 SCL GND SDA Reserved 22pf XIN GND, AGND, BoostGND 12MHz XOUT 22pf * Parallel Resonant Fundamental Mode 500uW 20-33pf ±5% *Bootloading begins after POR + 3ms BIOS bootup *GPIO[31:30] Up to 2k x8 >2k x8 to 64k x8 31 30 SCL SDA SDA SCL Power Savings and Reset Description This sections describes the different modes for resetting the chip and ways to save power. Power Saving Mode Description EZ-Host has one main power saving mode, Sleep. For detailed information about Sleep mode, see the Sleep section that follows. Sleep Sleep mode is the main chip power down mode and is also used for USB suspend. Sleep mode is entered by setting the Sleep Enable (bit 1) of the Power control register [0xC00A]. During Sleep mode (USB Suspend) the following events and states are true: ■ GPIO pins maintain their configuration during sleep (in suspend) Sleep mode is used for USB applications to support USB suspend and non USB applications as the main chip power down mode. ■ External Memory address pins are driven low ■ XTALOUT is turned off In addition, EZ-Host is capable of slowing down the CPU clock speed through the CPU Speed register [0xC008] without affecting other peripheral timing. Reducing the CPU clock speed from 48 MHz to 24 MHz reduces the overall current draw by around 8 mA while reducing it from 48 MHz to 3 MHz reduces the overall current draw by approximately 15 mA. ■ Internal PLL is turned off ■ Ensure that firmware disables the charge pump (OTG Control register [0xC098]) thereby causing OTGVBUS to drop below 0.2V. Otherwise OTGVBUS only drops to VCC – (2 schottky diode drops). ■ Booster circuit is turned off ■ USB transceivers is turned off ■ CPU goes into suspend mode until a programmable wakeup event Document #: 38-08015 Rev. *K Page 14 of 102 [+] Feedback CY7C67300 External (Remote) Wakeup Source There are several possible events available to wake EZ-Host from Sleep mode as shown in Table 20. These may also be used as remote wakeup options for USB applications. See the Power Control Register [0xC00A] [R/W] on page 20 for details. Upon wakeup, code begins executing within 200 µs, the time it takes the PLL to stabilize. Table 20. Wakeup Sources[5, 6] Wakeup Source (if enabled) Event USB Resume D+/D– Signaling OTGVBUS Level OTGID Any Edge HPI Read HSS Read SPI Read IRQ1 (GPIO 25) Any Edge IRQ0 (GPIO 24) Any Edge Power-On-Reset Description Memory Map The memory map is discussed in the following sections. Mapping The total memory space directly addressable by the CY16 processor is 64K (0x0000-0xFFFF). Program, data, and IO are contained within this 64K space. This memory space is byte addressable. Figure 10 on page 16 shows the various memory region address locations. Internal Memory Of the internal memory, 15K bytes are allocated for user's program and data. The lower memory space from 0x0000 to 0x04A2 is reserved for interrupt vectors, general purpose registers, USB control registers, stack, and other BIOS variables. The upper internal memory space contains EZ-Host control registers from 0xC000 to 0xC0FF and the BIOS ROM itself from 0xE000 to 0xFFFF. For more information about the reserved lower memory or the BIOS ROM, refer to the Programmer’s documentation and/or the BIOS documentation. During development with the EZ-Host toolset, leave the lower area of user's space (0x04A4 to 0x1000) available to load the GDB stub. The GDB stub is required to allow the toolset debug access into EZ-Host. The length of the power-on-reset event can be defined by (VCC ramp to valid) + (Crystal startup). A typical application might use a 12 ms power-on-reset event = ~7 ms + ~5 ms, respectively. The chip select pins are not active during accesses to internal memory. Reset Pin Up to 32 KB of external memory from 0x4000 - 0xBFFF is available via one chip select line (nXRAMSEL) with RAM Merge enabled (BIOS default). Additionally, another 8 KB region from 0xC100 - 0xDFFF is available via a second chip select line (nXROMSEL) giving 40 KB of total available external memory. Together with the internal 15 KB, this gives a total of either ~48 KB (one chip select) or ~56 KB (two chip selects) of available memory for either code or data. The Reset pin is active low and requires a minimum pulse duration of sixteen 12 MHz clock cycles (1.3 µs). A reset event restores all registers to their default POR settings. Code execution then begins 200 µs later at 0xFF00 with an immediate jump to 0xE000, the start of BIOS. Refer to BIOS documentation for additional details. USB Reset A USB Reset affects registers 0xC090 and 0xC0B0, all other registers remain unchanged. External Memory Note that the memory map and pin names (nXRAMSEL/nXROMSEL) define specific memory regions for RAM vs. ROM. This allows the BIOS to look in the upper external memory space at 0xC100 for SCAN vectors (enabling code to be loaded/executed from ROM). If no SCAN vectors are required in the design (external memory is used exclusively for data), then all external memory regions can be used for RAM. Similarly, the external memory can be used exclusively for code space (ROM). If more external memory is required, EZ-Host has enough address lines to support up to 512 KB. However, this requires complex code banking/paging schemes via the Extended Page registers. For further information about setting up the external memory, see the External Memory Interface on page 6. Notes 5. Read data is discarded (dummy data). 6. HPI_INT asserts on a USB Resume. Document #: 38-08015 Rev. *K Page 15 of 102 [+] Feedback CY7C67300 Figure 10. Memory Map Internal Memory HW INT's 0x0000 - 0x00FF SW INT's 0x0100 - 0x011F 0x0120 - 0x013F 0x0140 - 0x0148 0x014A - 0x01FF Primary Registers Swap Registers HPI Int / Mailbox LCP Variables 0x0200 - 0x02FF USB Registers 0x0300 - 0x030F 0x0310 - 0x03FF 0x0400 - 0x04A2 Slave Setup Packet BIOS Stack USB Slave & OTG 0x04A4 - 0x3FFF USER SPACE ~15K 0xC000 - 0xC0FF 0xE000 - 0xFFFF Document #: 38-08015 Rev. *K External Memory 0x4000 - 0x7FFF USER SPACE 16K 0x8000 - 0x9FFF Extended Page 1 01USER SPACE Up to 64 8K Banks Bank Selected by 0xC018 0xA000 - 0xBFFF Extended Page 2 01USER SPACE Up to 64 8K Banks Bank Selected by 0xC01A 0xC100 - 0xDFFF USER SPACE ~8K Control Registers BIOS Page 16 of 102 [+] Feedback CY7C67300 Registers Table 21. Processor Control Registers Some registers have different functions for a read vs. a write access or USB host vs. USB device mode. Therefore, registers of this type have multiple definitions for the same address. CPU Flags Register Register Name The default register values listed in this data sheet may be altered to some other value during the BIOS initialization. Refer to the BIOS documentation for register initialization information. Processor Control Registers There are nine registers dedicated to general processor control. Each of these registers are covered in this section and are summarized in Table 21. Address 0xC000 R/W R Register Bank Register 0xC002 R/W Hardware Revision Register 0xC004 R CPU Speed Register 0xC008 R/W Power Control Register 0xC00A R/W Interrupt Enable Register 0xC00E R/W Breakpoint Register 0xC014 R/W USB Diagnostic Register 0xC03C W Memory Diagnostic Register 0xC03E W CPU Flags Register [0xC000] [R] Table 22. CPU Flags Register Bit # 15 14 13 12 Field 11 10 9 8 Reserved... Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 ...Reserved Field 4 3 2 1 0 Global Interrupt Enable Negative Flag Overflow Flag Carry Flag Zero Flag Read/Write - - - R R R R R Default 0 0 0 X X X X X Register Description Overflow Flag (Bit 2) The CPU Flags register is a read only register that gives processor flags status. The Overflow Flag bit indicates if an overflow condition occurred. An overflow condition can occur if an arithmetic result was either larger than the destination operand size (for addition) or smaller than the destination operand must allow for subtraction. Global Interrupt Enable (Bit 4) The Global Interrupt Enable bit indicates if the Global Interrupts are enabled. 1: Enabled 1: Overflow occurred 0: Overflow did not occur 0: Disabled Carry Flag (Bit 1) Negative Flag (Bit 3) The Carry Flag bit indicates if an arithmetic operation resulted in a Carry for addition, or Borrow for subtraction. The Negative Flag bit indicates if an arithmetic operation results in a negative answer. 1: Carry/Borrow occurred 1: MS result bit is ‘1’ 0: MS result bit is not ‘1’ 0: Carry/Borrow did not occur Zero Flag (Bit 0) The Zero Flag bit indicates if an instruction execution resulted in a ‘0’. 1: Zero occurred 0: Zero did not occur Document #: 38-08015 Rev. *K Page 17 of 102 [+] Feedback CY7C67300 Bank Register [0xC002] [R/W] Table 23. Bank Register Bit # 15 14 13 12 11 10 9 8 R/W R/W R/W R/W Default 0 0 R/W R/W R/W R/W 0 0 0 0 0 1 Bit # 7 6 5 4 3 2 1 0 Field Read/Write Address... Field Read/Write Default ...Address Reserved R/W R/W R/W - - - - - 0 0 0 X X X X X Register Description The Bank register maps registers R0–R15 into RAM. The eleven MSBs of this register are used as a base address for registers R0–R15. A register address is automatically generated by: 1. Shifting the four LSBs of the register address left by 1. 2. ORing the four shifted bits of the register address with the twelve MSBs of the Bank register. 3. Forcing the LSB to zero. For example, if the Bank register is left at its default value of 0x0100, and R2 is read, then the physical address 0x0102 is read. Refer to Table 24 for details. Table 24. Bank Register Example Register Hex Value Binary Value Bank 0x0100 0000 0001 0000 0000 R14 0x000E << 1 = 0x001C 0000 0000 0001 1100 RAM Location 0x011C 0000 0001 0001 1100 Address (Bits [15:4]) The Address field is used as a base address for all register addresses to start from. Reserved Write all reserved bits with ’0’. Hardware Revision Register [0xC004] [R] Table 25. Revision Register Bit # 15 14 13 12 Field 11 10 9 8 Revision... Read/Write R R R R R R R R Default X X X X X X X X Bit # 7 6 5 4 3 2 1 0 Field ...Revision Read/Write R R R R R R R R Default X X X X X X X X Register Description The Hardware Revision register is a read only register that indicates the silicon revision number. The first silicon revision is represented by 0x0101. This number is increased by one for each new silicon revision. Revision (Bits [15:0]) The Revision field contains the silicon revision number. Document #: 38-08015 Rev. *K Page 18 of 102 [+] Feedback CY7C67300 CPU Speed Register [0xC008] [R/W] Table 26. CPU Speed Register Bit # 15 14 13 12 Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Read/Write - - - - R/W R/W R/W R/W Default 0 0 0 0 1 1 1 1 Field 11 10 9 8 Reserved... Field ...Reserved CPU Speed Register Description The CPU Speed register allows the processor to operate at a user selected speed. This register only affects the CPU, all other peripheral timing is still based on the 48 MHz system clock (unless otherwise noted). CPU Speed (Bits[3:0]) The CPU Speed field is a divisor that selects the operating speed of the processor as defined in Table 27. Table 27. CPU Speed Definition CPU Speed [3:0] Processor Speed 0000 48 MHz/1 0001 48 MHz/2 0010 48 MHz/3 0011 48 MHz/4 0100 48 MHz/5 0101 48 MHz/6 0110 48 MHz/7 0111 48 MHz/8 1000 48 MHz/9 1001 48 MHz/10 1010 48 MHz/11 1011 48 MHz/12 1100 48 MHz/13 1101 48 MHz/14 1110 48 MHz/15 1111 48 MHz/16 Reserved Write all reserved bits with ’0’. Document #: 38-08015 Rev. *K Page 19 of 102 [+] Feedback CY7C67300 Power Control Register [0xC00A] [R/W] Table 28. Power Control Register Bit # 15 14 13 12 11 10 9 8 Host/Device 2A Wake Enable Host/Device 1B Wake Enable Host/Device 1A Wake Enable OTG Wake Enable Reserved HSS Wake Enable SPI Wake Enable Field Host/Device 2B Wake Enable Read/Write R/W R/W R/W R/W R/W - R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 GPI Wake Enable Reserved Boost 3V OK Sleep Enable Halt Enable Field HPI Wake Enable Read/Write Default Reserved R/W - - R/W - R R/W R/W 0 0 0 0 0 0 0 0 Register Description OTG Wake Enable (Bit 11) The Power Control register controls the power down and wakeup options. Either the sleep mode or the halt mode options can be selected. All other writable bits in this register can be used as a wakeup source while in sleep mode. The OTG Wake Enable bit enables or disables a wakeup condition to occur on either an OTG VBUS_Valid or OTG ID transition (IRQ20). Host/Device 2B Wake Enable (Bit 15) 0: Disable wakeup on OTG VBUS valid or OTG ID transition The Host/Device 2B Wake Enable bit enables or disables a wakeup condition to occur on a Host/Device 2B transition. This wakeup from the SIE port does not cause an interrupt to the on-chip CPU. HSS Wake Enable (Bit 9) 1: Enable wakeup on OTG VBUS valid or OTG ID transition 0: Disable wakeup on Host/Device 2B transition The HSS Wake Enable bit enables or disables a wakeup condition to occur on an HSS Rx serial input transition. The processor may take several hundreds of microseconds before being operational after wakeup. Therefore, the incoming data byte that causes the wakeup is discarded. Host/Device 2A Wake Enable (Bit 14) 1: Enable wakeup on HSS Rx serial input transition The Host/Device 2A Wake Enable bit enables or disables a wakeup condition to occur on an Host/Device 2A transition. This wakeup from the SIE port does not cause an interrupt to the on-chip CPU. 0: Disable wakeup on HSS Rx serial input transition 1: Enable wakeup on Host/Device 2B transition 1: Enable wakeup on Host/Device 2A transition 0: Disable wakeup on Host/Device 2A transition Host/Device 1B Wake Enable (Bit 13) The Host/Device 1B Wake Enable bit enables or disables a wakeup condition to occur on an Host/Device 1B transition. This wakeup from the SIE port does not cause an interrupt to the on-chip CPU. SPI Wake Enable (Bit 8) The SPI Wake Enable bit enables or disables a wakeup condition to occur on a falling SPI_nSS input transition. The processor may take several hundreds of microseconds before being operational after wakeup. Therefore, the incoming data byte that causes the wakeup is discarded. 1: Enable wakeup on falling SPI nSS input transition 0: Disable SPI_nSS interrupt HPI Wake Enable (Bit 7) 1: Enable wakeup on Host/Device 1B transition The HPI Wake Enable bit enables or disables a wakeup condition to occur on an HPI interface read. 0: Disable wakeup on Host/Device 1B transition 1: Enable wakeup on HPI interface read Host/Device 1A Wake Enable (Bit 12) 0: Disable wakeup on HPI interface read The Host/Device 1A Wake Enable bit enables or disables a wakeup condition to occur on an Host/Device 1A transition. This wakeup from the SIE port does not cause an interrupt to the on-chip CPU. The GPI Wake Enable bit enables or disables a wakeup condition to occur on a GPIO(25:24) transition. 1: Enable wakeup on Host/Device 1A transition 1: Enable wakeup on GPIO(25:24) transition 0: Disable wakeup on Host/Device 1A transition 0: Disable wakeup on GPIO(25:24) transition Document #: 38-08015 Rev. *K GPI Wake Enable (Bit 4) Page 20 of 102 [+] Feedback CY7C67300 Boost 3V OK (Bit 2) Halt Enable (Bit 0) The Boost 3V OK bit is a read only bit that returns the status of the OTG Boost circuit. Setting this bit to ‘1’ immediately initiates HALT mode. While in HALT mode, only the CPU is stopped. The internal clock still runs and all peripherals still operate, including the USB engines. The power saving using HALT in most cases is minimal, but in applications that are very CPU intensive the incremental savings may provide some benefit. 1: Boost circuit not ok and internal voltage rails are below 3.0V 0: Boost circuit ok and internal voltage rails are at or above 3.0V Sleep Enable (Bit 1) Setting this bit to ‘1’ immediately initiates SLEEP mode. While in SLEEP mode, the entire chip is paused, achieving the lowest standby power state. All operations are paused, the internal clock is stopped, the booster circuit and OTG VBUS charge pump are all powered down, and the USB transceivers are powered down. All counters and timers are paused but retain their values; enabled PWM outputs freeze in their current states. SLEEP mode exits by any activity selected in this register. When SLEEP mode ends, instruction execution resumes within 0.5 ms. 1: Enable Sleep mode The HALT state is exited when any enabled interrupt is triggered. Upon exiting the HALT state, one or two instructions immediately following the HALT instruction may be executed before the waking interrupt is serviced (you may want to follow the HALT instruction with two NOPs). 1: Enable Halt mode 0: No function Reserved Write all reserved bits with ’0’. 0: No function Interrupt Enable Register [0xC00E] [R/W] Table 29. Interrupt Enable Register Bit # 15 14 13 Reserved Field 12 11 10 OTG Interrupt Enable SPI Interrupt Enable Reserved 9 8 Host/Device 2 Host/Device 1 Interrupt Interrupt Enable Enable Read/Write - - - R/W R/W - R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 In Mailbox Interrupt Enable Out Mailbox Interrupt Enable Reserved Field HSS Interrupt Enable UART Interrupt Enable GPIO Interrupt Enable Timer 1 Interrupt Enable Timer 0 Interrupt Enable R/W R/W R/W - R/W R/W R/W R/W 0 0 0 1 0 0 0 0 Read/Write Default Register Description Host/Device 2 Interrupt Enable (Bit 9) The Interrupt Enable register allows control of the hardware interrupt vectors. The Host/Device 2 Interrupt Enable bit enables or disables all of the following Host/Device 2 hardware interrupts: Host 2 USB Done, Host 2 USB SOF/EOP, Host 2 Wakeup/Insert/Remove, Device 2 Reset, Device 2 SOF/EOP or WakeUp from USB, Device 2 Endpoint n. OTG Interrupt Enable (Bit 12) The OTG Interrupt Enable bit enables or disables the OTG ID/OTG4.4V Valid hardware interrupt. 1: Enable OTG interrupt 0: Disable OTG interrupt SPI Interrupt Enable (Bit 11) The SPI Interrupt Enable bit enables or disables the following three SPI hardware interrupts: SPI TX, SPI RX, and SPI DMA Block Done. 1: Enable SPI interrupt 0: Disable SPI interrupt Document #: 38-08015 Rev. *K 1: Enable Host 2 and Device 2 interrupt 0: Disable Host 2 and Device 2 interrupt Host/Device 1 Interrupt Enable (Bit 8) The Host/Device 1 Interrupt Enable bit enables or disables all of the following Host/Device 1 hardware interrupts: Host 1 USB Done, Host 1 USB SOF/EOP, Host 1 Wakeup/Insert/Remove, Device 1 Reset, Device 1 SOF/EOP or WakeUp from USB, Device 1Endpoint n. 1: Enable Host 1 and Device 1 interrupt 0: Disable Host 1 and Device 1 interrupt Page 21 of 102 [+] Feedback CY7C67300 HSS Interrupt Enable (Bit 7) GPIO Interrupt Enable (Bit 2) The HSS Interrupt Enable bit enables or disables the following High-speed Serial Interface hardware interrupts: HSS Block Done and HSS RX Full. 1: Enable HSS interrupt The GPIO Interrupt Enable bit enables or disables the General Purpose IO pins interrupt (see the GPIO Control Register [0xC006] [R/W] on page 51). When the GPIO bit is reset, all pending GPIO interrupts are also cleared 0: Disable HSS interrupt 1: Enable GPIO interrupt 0: Disable GPIO interrupt In Mailbox Interrupt Enable (Bit 6) Timer 1 Interrupt Enable (Bit 1) The In Mailbox Interrupt Enable bit enables or disables the HPI: Incoming Mailbox hardware interrupt. The Timer 1 Interrupt Enable bit enables or disables the TImer1 Interrupt Enable. When this bit is reset, all pending Timer 1 interrupts are cleared. 1: Enable MBXI interrupt 0: Disable MBXI interrupt 1: Enable TM1 interrupt Out Mailbox Interrupt Enable (Bit 5) 0: Disable TM1 interrupt The Out Mailbox Interrupt Enable bit enables or disables the HPI: Outgoing Mailbox hardware interrupt. Timer 0 Interrupt Enable (Bit 0) 0: Disable MBXO interrupt The Timer 0 Interrupt Enable bit enables or disables the TImer0 Interrupt Enable. When this bit is reset, all pending Timer 0 interrupts are cleared. UART Interrupt Enable (Bit 3) 1: Enable TM0 interrupt The UART Interrupt Enable bit enables or disables the following UART hardware interrupts: UART TX, and UART RX. 0: Disable TM0 interrupt 1: Enable MBXO interrupt 1: Enable UART interrupt Reserved Write all reserved bits with ’0’. 0: Disable UART interrupt Breakpoint Register [0xC014] [R/W] Table 30. Breakpoint Register Bit # 15 14 13 12 11 10 9 8 R/W R/W R/W R/W Default 0 0 R/W R/W R/W R/W 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Field Read/Write Address... Field Read/Write Default ...Address Register Description Address (Bits [15:0]) The Breakpoint register holds the breakpoint address. When the program counter matches this address, the INT127 interrupt occurs. To clear this interrupt, write a zero value to this register. The Address field is a 16-bit field containing the breakpoint address. Document #: 38-08015 Rev. *K Page 22 of 102 [+] Feedback CY7C67300 USB Diagnostic Register [0xC03C] [R/W] Table 31. USB Diagnostic Register Bit # 15 14 13 12 Field Port 2B Diagnostic Enable Port 2A Diagnostic Enable Port 1B Diagnostic Enable Port 1A Diagnostic Enable Read/Write 11 10 9 8 Reserved... R/W R/W R/W R/W - - - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 ...Reserved Pull-down Enable LS Pull-up Enable FS Pull-up Enable Reserved Read/Write - R/W R/W R/W - R/W R/W R/W Default 0 0 0 0 0 0 0 0 Field Force Select Register Description Pull-down Enable (Bit 6) The USB Diagnostic register provides control of diagnostic modes. It is intended for use by device characterization tests, not for normal operations. This register is read/write by the on-chip CPU but is write-only via the HPI port. The Pull-down Enable bit enables or disables full-speed pull down resistors (pull down on both D+ and D–) for testing. Port 2B Diagnostic Enable (Bit 15) The Port 2B Diagnostic Enable bit enables or disables Port 2B for the test conditions selected in this register. 1: Apply any of the following enabled test conditions: J/K, DCK, SE0, RSF, RSL, PRD 1: Enable pull down resistors on both D+ and D– 0: Disable pull down resistors on both D+ and D– LS Pull-up Enable (Bit 5) The LS Pull-up Enable bit enables or disables a low-speed pull up resistor (pull up on D–) for testing. 1: Enable low-speed pull up resistor on D– 0: Do not apply test conditions 0: Pull-up resistor is not connected on D– Port 2A Diagnostic Enable (Bit 14) FS Pull-up Enable (Bit 4) The Port 2A Diagnostic Enable bit enables or disables Port 2A for the test conditions selected in this register. The FS Pull-up Enable bit enables or disables a full-speed pull up resistor (pull up on D+) for testing. 1: Apply any of the following enabled test conditions: J/K, DCK, SE0, RSF, RSL, PRD 1: Enable full-speed pull up resistor on D+ 0: Do not apply test conditions Port 1B Diagnostic Enable (Bit 13) The Port 1B Diagnostic Enable bit enables or disables Port 1B for the test conditions selected in this register. 1: Apply any of the following enabled test conditions: J/K, DCK, SE0, RSF, RSL, PRD 0: Pull up resistor is not connected on D+ Force Select (Bits [2:0]) The Force Select field bit selects several different test condition states on the data lines (D+/D–). Refer to Table 32 for details. Table 32. Force Select Definition Force Select [2:0] Data Line State 1xx Assert SE0 0: Do not apply test conditions Port 1A Diagnostic Enable (Bit 12) The Port 1A Diagnostic Enable bit enables or disables Port 1A for the test conditions selected in this register. 1: Apply any of the following enabled test conditions: J/K, DCK, SE0, RSF, RSL, PRD 0: Do not apply test conditions Document #: 38-08015 Rev. *K 01x Toggle JK 001 Assert J 000 Assert K Reserved Write all reserved bits with ’0’. Page 23 of 102 [+] Feedback CY7C67300 Memory Diagnostic Register [0xC03E] [W] Table 33. Memory Diagnostic Register Bit # 15 14 13 12 11 10 Reserved 9 8 Memory Arbitration Select Field Read/Write - - - - - W W W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Reserved Monitor Enable Field Read/Write - - - - - - - W Default 0 0 0 0 0 0 0 0 Register Description Reserved The Memory Diagnostic register provides control of diagnostic modes. Write all reserved bits with ’0’. Memory Arbitration Select (Bits[10:8]) The Memory Arbitration Select field is defined in Table 34. Table 34. Memory Arbitration Select External Memory Registers There are four registers dedicated to controlling the external memory interface. Each of these registers are covered in this section and are summarized in Table 35. Table 35. External Memory Control Registers Memory Arbitration Select [3:0] Memory Arbitration Timing 111 1/8, 7 of every 8 cycles dead Extended Page 1 Map Register 0xC018 R/W 110 2/8, 6 of every 8 cycles dead Extended Page 2 Map Register 0xC01A R/W 101 3/8, 5 of every 8 cycles dead Upper Address Enable Register 0xC038 R/W 100 4/8, 4 of every 8 cycles dead External Memory Control Register 0xC03A R/W 011 5/8, 3 of every 8 cycles dead 010 6/8, 2 of every 8 cycles dead 001 7/8, 1 of every 8 cycles dead 000 8/8, all cycles available Register Name Address R/W Monitor Enable (Bit 0) The Monitor Enable bit enables or disables monitor mode. In monitor mode the internal address bus is echoed to the external address pins. 1: Enable monitor mode 0: Disable monitor mode Document #: 38-08015 Rev. *K Page 24 of 102 [+] Feedback CY7C67300 Extended Page n Map Register [R/W] ■ Extended Page 1 Map Register 0xC018 ■ Extended Page 2 Map Register 0xC01A Table 36. Extended Page n Map Register Bit # 15 14 13 12 11 10 9 8 R/W R/W R/W R/W Default 0 0 R/W R/W R/W R/W 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Field Read/Write Address... Field Read/Write Default ...Address reflect the content of this register when the CPU accesses the address 0x8000-0x9FFF. For the SRAM mode, the address pin on [4:0] (Page n address [17:13]) is used. Register Description The Extended Page n Map register contains the Page n high-order address bits. These bits are always appended to accesses to the Page n Memory mapped space. Set bit [8] (Page n address [21]) to ‘0’, so that Page n reads/writes access external areas (SRAM, ROM or peripherals). nXMEMSEL is the external chip select for this space. Address (Bits [15:0]) The Address field contains the high-order bits 28 to 13 of the Page n address. The address pins [8:0] (Page n address [21:13]) Upper Address Enable Register [0xC038] [R/W] Table 37. External Memory Control Register Bit # 15 14 13 12 Field 11 10 9 8 Reserved Read/Write - - - - - - - - Default X X X X X X X X Bit # 7 6 5 4 3 2 1 0 Reserved Upper Address Enable Field Read/Write - - - - R/W Default X X X X 0 Reserved X X X Register Description Upper Address Enable (Bit 3) The Upper Address Enable register enables/disables the four most significant bits of the external address A[18:15]. This register defaults to having the Upper Address disabled. Note that on power up, pins A[18:15] are driven high. The Upper Address Enable bit enables/disables the four most significant bits of the external address A[18:15]. 1: Enable A[18:15] of the external memory interface for general addressing. 0: Disable A[18:15], not available. Reserved Write all reserved bits with ’0’. Document #: 38-08015 Rev. *K Page 25 of 102 [+] Feedback CY7C67300 External Memory Control Register [0xC03A] [R/W] Table 38. External Memory Control Register Bit # 15 14 Reserved 13 12 11 XRAM Merge XROM Merge Enable Enable Field 10 XMEM Width Select 9 8 XMEM Wait Select Read/Write - - R/W R/W R/W R/W R/W R/W Default X X X X X X X X Bit # 7 6 5 4 3 2 1 0 Field XROM Width Select Read/Write Default XROM Wait Select XRAM Width Select XRAM Wait Select R/W R/W R/W R/W R/W R/W R/W R/W X X X X X X X X Register Description XROM Wait Select (Bits[6:4]) The External Memory Control register provides control of Wait States for the external SRAM or ROM. All wait states are based off of 48 MHz. The XROM Wait Select field selects the external ROM wait state from 0 to 7. XRAM Merge Enable (Bit 13) The XRAM Width Select bit selects the external RAM width. The XRAM Merge Enable bit enables or disables the RAM merge feature. When the RAM merge feature is enabled, the nXRAMSEL is active whenever the nXMEMSEL is active. 1: External memory = 8 XRAM Width Select (Bit 3) 0: External memory = 16 1: Enable RAM merge XRAM Wait Select (Bits[2:0]) 0: Disable RAM merge The XRAM Wait Select field selects the external RAM wait state from 0 to 7. XROM Merge Enable (Bit 12) The XROM Merge Enable bit enables or disables the ROM merge feature. When the ROM merge feature is enabled, the nXROMSEL is active whenever the nXMEMSEL is active. Reserved 1: Enable ROM merge Timer Registers 0: Disable ROM merge XMEM Width Select (Bit 11) There are three registers dedicated to timer operations. Each of these registers are discussed in this section and are summarized in Table 39. The XMEM Width Select bit selects the extended memory width. Table 39. Timer Registers 1: Extended memory = 8 Write all reserved bits with ’0’. Register Name Address R/W 0: Extended memory = 16 Watchdog Timer Register 0xC00C R/W XMEM Wait Select (Bits [10:8]) Timer 0 Register 0xC010 R/W The XMEM Wait Select field selects the extended memory wait state from 0 to 7. Timer 1 Register 0xC012 R/W XROM Width Select (Bit 7) The XROM Width Select bit selects the external ROM width. 1: External memory = 8 0: External memory = 16 Document #: 38-08015 Rev. *K Page 26 of 102 [+] Feedback CY7C67300 Watchdog Timer Register [0xC00C] [R/W] Table 40. Watchdog Timer Register Bit # 15 14 13 12 11 10 9 8 R/W R/W R/W R/W Default 0 0 R/W R/W R/W R/W 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Lock Enable WDT Enable Reset Strobe Field Reserved... Read/Write ...Reserved Timeout Flag Field Read/Write Default Period Select R/W R/W R/W R/W R/W R/W R/W W 0 0 0 0 0 0 0 0 Register Description Lock Enable (Bit 2) The Watchdog Timer register provides status and control over the Watchdog timer. The Watchdog timer can also interrupt the processor. The Lock Enable bit does not allow any writes to this register until a reset. In doing so the Watchdog timer can be set up and enabled permanently so that it can only be cleared on reset (the WDT Enable bit is ignored). Timeout Flag (Bit 5) The Timeout Flag bit indicates if the Watchdog timer expired. The processor can read this bit after exiting a reset to determine if a Watchdog timeout occurred. This bit is cleared on the next external hardware reset. 1: Watchdog timer expired. 0: Watchdog timer not permanently set WDT Enable (Bit 1) The WDT Enable bit enables or disables the Watchdog timer. 1: Enable Watchdog timer operation 0: Watchdog timer did not expire. 0: Disable Watchdog timer operation Period Select (Bits [4:3]) The Period Select field is defined in Table 41. If this time expires before the Reset Strobe bit is set, the internal processor is reset. Table 41. Period Select Definition Period Select[4:3] 00 WDT Period Value 1.4 ms 01 10 11 5.5 ms 22.0 ms 66.0 ms Document #: 38-08015 Rev. *K 1: Watchdog timer permanently set Reset Strobe (Bit 0) The Reset Strobe is a write-only bit that resets the Watchdog timer count. Set this bit to ‘1’ before the count expires to avoid a Watchdog trigger 1: Reset Count Reserved Write all reserved bits with ’0’. Page 27 of 102 [+] Feedback CY7C67300 Timer n Register [R/W] ■ Timer 0 Register 0xC010 ■ Timer 1 Register 0xC012 Table 42. Timer n Register Bit # 15 14 13 12 11 10 9 8 R/W R/W R/W R/W Default 1 1 R/W R/W R/W R/W 1 1 1 1 1 1 Bit # 7 6 5 4 3 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W 1 1 1 1 1 1 1 1 Field Count... Read/Write Field ...Count Read/Write Default functions for both USB host and USB peripheral options and is covered in this section and summarized in Table 43. USB Host only registers are covered in UART Interface on page 8, and USB device only registers are covered in External Memory Registers on page 24. Register Description The Timer n Register sets the Timer n count. Both Timer 0 and Timer 1 decrement by one every 1 µs clock tick. Each can provide an interrupt to the CPU when the timer reaches zero. Count (Bits [15:0]) Table 43. General USB Registers The Count field sets the Timer count. Register Name General USB Registers Address (SIE1/SIE2) USB n Control Register R/W 0xC08A/0xC0AA R/W There is one set of registers dedicated to general USB control. This set consists of two identical registers: one for Host/Device Port 1 and one for Host/Device Port 2. This register set has USB n Control Register [R/W] ■ USB 1 Control Register 0xC08A ■ USB 2 Control Register 0xC0AA Table 44. USB n Control Register Bit # 15 14 13 12 11 10 9 8 Port B D– Status Port A D+ Status Port A D– Status LOB LOA Mode Select Field Port B D+ Status Port B Resistors Enable Read/Write R R R R R/W R/W R/W R/W Default X X X X 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Suspend Enable Field Port A Resistors Enable Port B SOF/EOP Enable Port A SOF/EOP Enable Read/Write Default Port B Force D± State Port A Force D± State R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Register Description Port B D+ Status (Bit 15) The USB n Control register is used in both host and device mode. It monitors and controls the SIE and the data lines of the USB ports. This register can be accessed by the HPI interface. The Port B D+ Status bit is a read only bit that indicates the value of DATA+ on Port B. 1: D+ is HIGH 0: D+ is LOW Document #: 38-08015 Rev. *K Page 28 of 102 [+] Feedback CY7C67300 The Port B D– Status bit is a read only bit that indicates the value of DATA– on Port B. enabled. When the Mode Select is set for Device mode, a single pull up resistor on either D+ or D–, determined by the LOA bit, is enabled. See Table 45 for details. 1: D– is HIGH 1: Enable pull up/pull down resistors 0: D– is LOW 0: Disable pull up/pull down resistors Port B D– Status (Bit 14) Port A D+ Status (Bit 13) Table 45. USB Data Line Pull Up and Pull Down Resistors L0A/ L0B Mode Select Port n Resistors Enable X X 0 Pull up/Pull down on D+ and D– Disabled Port A D– Status (Bit 12) X 1 1 The Port A D– Status bit is a read only bit that indicates the value of DATA– on Port A. Pull down on D+ and D– Enabled 1 0 1 Pull up on USB D– Enabled 1: D– is HIGH 0 0 1 Pull up on USB D+ Enabled The Port A D+ Status bit is a read only bit that indicates the value of DATA+ on Port A. 1: D+ is HIGH 0: D+ is LOW 0: D– is LOW LOB (Bit 11) The LOB bit selects the speed of Port B. 1: Port B is set to low-speed mode 0: Port B is set to full-speed mode LOA (Bit 10) The LOA bit selects the speed of Port A. 1: Port A is set to low-speed mode 0: Port A is set to full-speed mode Mode Select (Bit 9) The Mode Select bit sets the SIE for host or device operation. When set for device operation only one USB port is supported. The active port is selected by the Port Select bit in the Host n Count register. Function Port B Force D± State (Bits [6:5]) The Port B Force D± State field controls the forcing state of the D+ D– data lines for Port B. This field forces the state of the Port B data lines independent of the Port Select bit setting. See Table 46 for details. Port A Force D± State (Bits [4:3]) The Port A Force D± State field controls the forcing state of the D+ D– data lines for Port A. This field forces the state of the Port A data lines independent of the Port Select bit setting. See Table 46 for details. Table 46. Port A/B Force D± State Port A/B Force D± State Function MSb LSb 0 0 Normal Operation 1 0 Force USB Reset, SE0 State 1: Host mode 0 1 Force J-State 0: Device mode 1 1 Force K-State Port B Resistors Enable (Bit 8) The Port B Resistors Enable bit enables or disables the pull up/pull down resistors on Port B. When enabled, the Mode Select bit and LOB bit of this register set the pull up/pull down resistors appropriately. When the Mode Select is set for Host mode, the pull down resistors on the data lines (D+ and D–) are enabled. When the Mode Select is set for Device mode, a single pull up resistor on either D+ or D–, determined by the LOB bit, is enabled. See Table 45 for details. Suspend Enable (Bit 2) The Suspend Enable bit enables or disables the suspend feature on both ports. When suspend is enabled the USB transceivers are powered down and cannot transmit or received USB packets but can still monitor for a wakeup condition. 1: Enable suspend 0: Disable suspend 1: Enable pull up/pull down resistors Port B SOF/EOP Enable (Bit 1) 0: Disable pull up/pull down resistors The Port B SOF/EOP Enable bit is only applicable in host mode. In device mode, this bit must be written as ‘0’. In host mode this bit enables or disables SOFs or EOPs for Port B. Either SOFs or EOPs are generated depending on the LOB bit in the USB n Control register when Port B is active. Port A Resistors Enable (Bit 7) The Port A Resistors Enable bit enables or disables the pull up/pull down resistors on Port A. When enabled, the Mode Select bit and LOA bit of this register set the pull up/pull down resistors appropriately. When the Mode Select is set for Host mode, the pull down resistors on the data lines (D+ and D–) are Document #: 38-08015 Rev. *K 1: Enable SOFs or EOPs 0: Disable SOFs or EOPs Page 29 of 102 [+] Feedback CY7C67300 Port A SOF/EOP Enable (Bit 0) Reserved The Port A SOF/EOP Enable bit is only applicable in host mode. In device mode this bit must be written as ‘0’. In host mode this bit enables or disables SOFs or EOPs for Port A. Either SOFs or EOPs are generated depending on the LOA bit in the USB n Control register when Port A is active. Write all reserved bits with ’0’. 1: Enable SOFs or EOPs 0: Disable SOFs or EOPs USB Host Only Registers There are twelve sets of dedicated registers for USB host only operation. Each set consists of two identical registers (unless otherwise noted), one for Host Port 1 and one for Host Port 2. These register sets are covered in this section and summarized in Table 47. Table 47. USB Host Only Register Register Name Address (Host 1/Host 2) R/W Host n Control Register 0xC080/0xC0A0 R/W Host n Address Register 0xC082/0xC0A2 R/W Host n Count Register 0xC084/0xC0A4 R/W Host n Endpoint Status Register 0xC086/0xC0A6 R Host n PID Register 0xC086/0xC0A6 W Host n Count Result Register 0xC088/0xC0A8 R Host n Device Address Register 0xC088/0xC0A8 W Host n Interrupt Enable Register 0xC08C/0xC0AC R/W Host n Status Register 0xC090/0xC0B0 R/W Host n SOF/EOP Count Register 0xC092/0xC0B2 R/W Host n SOF/EOP Counter Register 0xC094/0xC0B4 R Host n Frame Register 0xC096/0xC0B6 R Host n Control Register [R/W] ■ Host 1 Control Register 0xC080 ■ Host 2 Control Register 0xC0A0 Table 48. Host n Control Register Bit # 15 14 13 12 Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 3 2 1 Field 11 10 9 8 Reserved Bit # 7 6 5 4 Field Preamble Enable Sequence Select Sync Enable ISO Enable R/W R/W R/W R/W - - - R/W 0 0 0 0 0 0 0 0 Read/Write Default Reserved 0 Arm Enable Register Description Preamble Enable (Bit 7) The Host n Control register allows high level USB transaction control. The Preamble Enable bit enables or disables the transmission of a preamble packet before all low-speed packets. Set this bit only when communicating with a low-speed device. 1: Enable Preamble packet 0: Disable Preamble packet Document #: 38-08015 Rev. *K Page 30 of 102 [+] Feedback CY7C67300 Sequence Select (Bit 6) ISO Enable (Bit 4) The Sequence Select bit sets the data toggle for the next packet. This bit has no effect on receiving data packets; sequence checking must be handled in firmware. The ISO Enable bit enables or disables an isochronous transaction. 1: Enable isochronous transaction 1: Send DATA1 0: Disable isochronous transaction 0: Send DATA0 Arm Enable (Bit 0) Sync Enable (Bit 5) The Arm Enable bit arms an endpoint and starts a transaction. This bit is automatically cleared to ‘0’ when a transaction is complete. The Sync Enable bit synchronizes the transfer with the SOF packet in full-speed mode and the EOP packet in low-speed mode. 1: Arm endpoint and begin transaction 1: The next enabled packet is transferred after the SOF or EOP packet is transmitted 0: Endpoint disarmed 0: The next enabled packet is transferred as soon as the SIE is free Reserved Write all reserved bits with ’0’. Host n Address Register [R/W] ■ Host 1 Address Register 0xC082 ■ Host 2 Address Register 0xC0A2 Table 49. Host n Address Register Bit # 15 14 13 12 Field Read/Write 11 10 9 8 Address... R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field Read/Write Default ...Address R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Register Description Address (Bits [15:0]) The Host n Address register is used as the base pointer into memory space for the current host transactions. The Address field sets the address pointer into internal RAM or ROM. Host n Count Register [R/W] ■ Host 1 Count Register 0xC084. ■ Host 2 Count Register 0xC0A4. Table 50. Host n Count Register Bit # 15 14 Reserved Port Select Read/Write - R/W - - - - R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field 13 12 Field Read/Write Default 11 10 9 Reserved 8 Count... ...Count R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Document #: 38-08015 Rev. *K Page 31 of 102 [+] Feedback CY7C67300 Register Description Table 51. Port Select Definition The Host n Count register is used to hold the number of bytes (packet length) for the current transaction. The maximum packet length is 1023 bytes in ISO mode. The Host Count value is used to determine how many bytes to transmit, or the maximum number of bytes to receive. If the number of received bytes is greater then the Host Count value then an overflow condition is flagged by the Overflow bit in the Host n Endpoint Status register. Port Select Host/Device 1 Active Port Host/Device 2 Active Port 0 A A 1 B B Count (Bits [9:0]) The Port Select bit selects which of the two active ports is selected and is summarized in Table 51. The Count field sets the value for the current transaction data packet length. This value is retained when switching between host and device mode, and back again. 1: Port 1B or Port 2B is enabled Reserved 0: Port 1A or Port 2A is enabled Write all reserved bits with ’0’. Port Select (Bit 14) Host n Endpoint Status Register [R] ■ Host 1 Endpoint Status Register 0xC086 ■ Host 2 Endpoint Status Register 0xC0A6 Table 52. Host n Endpoint Status Register Bit # 15 14 13 12 Reserved Field 11 10 Overflow Flag Underflow Flag 9 8 Reserved Read/Write - - - - R R - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Stall Flag NAK Flag Length Exception Flag Reserved Sequence Status Timeout Flag Error Flag ACK Flag Read/Write R R R - R R R R Default 0 0 0 0 0 0 0 0 Field Register Description Stall Flag (Bit 7) The Host n Endpoint Status register is a read only register that provides status for the last USB transaction. The Stall Flag bit indicates that the peripheral device replied with a Stall in the last transaction. 1: Device returned Stall 0: Device did not return Stall Overflow Flag (Bit 11) The Overflow Flag bit indicates that the received data in the last data transaction exceeded the maximum length specified in the Host n Count register. The Overflow Flag must be checked in response to a Length Exception signified by the Length Exception Flag set to ‘1’. 1: Overflow condition occurred 0: Overflow condition did not occur NAK Flag (Bit 6) The NAK Flag bit indicates that the peripheral device replied with a NAK in the last transaction. 1: Device returned NAK 0: Device did not return NAK Underflow Flag (Bit 10) Length Exception Flag (Bit 5) The Underflow Flag bit indicates that the received data in the last data transaction was less than the maximum length specified in the Host n Count register. The Underflow Flag must be checked in response to a Length Exception signified by the Length Exception Flag set to ‘1’. The Length Exception Flag bit indicates that the received data in the data stage of the last transaction does not equal the maximum Host Count specified in the Host n Count register. A Length Exception can either mean an overflow or underflow and the Overflow and Underflow flags (bits 11 and 10, respectively) must be checked to determine which event occurred. 1: An overflow or underflow condition occurred 0: An overflow or underflow condition did not occur 1: Underflow condition occurred 0: Underflow condition did not occur Document #: 38-08015 Rev. *K Page 32 of 102 [+] Feedback CY7C67300 a STALL. Overflow and Underflow are not considered errors and do not affect this bit. CRC5 and CRC16 errors result in an Error flag along with receiving incorrect packet types. 1: Error detected 0: No error detected Sequence Status (Bit 3) The Sequence Status bit indicates the state of the last received data toggle from the device. Firmware is responsible for monitoring and handling the sequence status. The Sequence bit is only valid if the ACK bit is set to ‘1’. The Sequence bit is set to ‘0’ when an error is detected in the transaction and the Error bit is set. 1: DATA1 0: DATA0 ACK Flag (Bit 0) The ACK Flag bit indicates two different conditions depending on the transfer type. For non-isochronous transfers, this bit represents a transaction ending by receiving or sending an ACK packet. For isochronous transfers, this bit represents a successful transaction that is not represented by an ACK packet. Timeout Flag (Bit 2) The Timeout Flag bit indicates if a timeout condition occurred for the last transaction. A timeout condition can occur when a device either takes too long to respond to a USB host request or takes too long to respond with a handshake. 1: Timeout occurred 0: Timeout did not occur 1: For non-isochronous transfers, the transaction was ACKed. For isochronous transfers, the transaction was completed successfully 0: For non-isochronous transfers, the transaction was not ACKed. For isochronous transfers, the transaction did not complete successfully Error Flag (Bit 1) The Error Flag bit indicates a transaction failed for any reason other than the following: timeout, receiving a NAK, or receiving Host n PID Register [W] ■ Host 1 PID Register 0xC086 ■ Host 2 PID Register 0xC0A6 Table 53. Host n PID Register Bit # 15 14 13 12 Field 11 10 9 8 Reserved Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Read/Write W W W W W W W W Default 0 0 0 0 0 0 0 0 Field PID Select Document #: 38-08015 Rev. *K Endpoint Select Page 33 of 102 [+] Feedback CY7C67300 Register Description Endpoint Select (Bits [3:0]) The Host n PID register is a write only register that provides the PID and Endpoint information to the USB SIE to be used in the next transaction. The Endpoint field allows addressing of up to 16 different endpoints. PID Select (Bits [7:4]) Write all reserved bits with ’0’. Reserved The PID Select field is defined in Table 54. ACK and NAK tokens are automatically sent based on settings in the Host n Control register and do not need to be written in this register. Table 54. PID Select Definition PID TYPE PID Select [7:4] SETUP 1101 (D Hex) IN 1001 (9 Hex) OUT 0001 (1 Hex) SOF 0101 (5 Hex) PREAMBLE 1100 (C Hex) NAK 1010 (A Hex) STALL 1110 (E Hex) DATA0 0011 (3 Hex) DATA1 1011 (B Hex) Host n Count Result Register [R] ■ Host 1 Count Result Register 0xC088 ■ Host 2 Count Result Register 0xC0A8 Table 55. Host n Count Result Register Bit # 15 14 13 12 Field 11 10 9 8 Result... Read/Write R R R R R R R R Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field ...Result Read/Write R R R R R R R R Default 0 0 0 0 0 0 0 0 Register Description Result (Bits [15:0]) The Host n Count Result register is a read only register that contains the size difference in bytes between the Host Count Value specified in the Host n Count register and the last packet received. If an overflow or underflow condition occurs, that is the received packet length differs from the value specified in the Host n Count register, the Length Exception Flag bit in the Host n Endpoint Status register is set. The value in this register is only value when the Length Exception Flag bit is set and the Error Flag bit is not set, both bits are in the Host n Endpoint Status register. The Result field contains the differences in bytes between the received packet and the value specified in the Host n Count register. If an overflow condition occurs, Result [15:10] is set to ‘111111’, a 2’s complement value indicating the additional byte count of the received packet. If an underflow condition occurs, Result [15:0] indicates the excess bytes count (number of bytes not used). Document #: 38-08015 Rev. *K Reserved Write all reserved bits with ’0’. Page 34 of 102 [+] Feedback CY7C67300 Host n Device Address Register [W] ■ Host 1 Device Address Register 0xC088 ■ Host 2 Device Address Register 0xC0A8 Table 56. Host n Device Address Register Bit # 15 14 13 12 Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field ...Reserved Field 11 10 9 8 Reserved... Address Read/Write - W W W W W W W Default 0 0 0 0 0 0 0 0 Register Description Address (Bits [6:0]) The Host n Device Address register is a write only register that contains the USB Device Address that the host wants to communicate with. The Address field contains the value of the USB address for the next device that the host is going to communicate with. This value must be written by firmware. Reserved Write all reserved bits with ’0’. Host n Interrupt Enable Register [R/W] ■ Host 1 Interrupt Enable Register 0xC08C ■ Host 2 Interrupt Enable Register 0xC0AC Table 57. Host n Interrupt Enable Register Bit # 15 14 ID Interrupt Enable Field VBUS Interrupt Enable R/W R/W - - - - R/W - 0 0 0 0 0 0 0 0 7 6 5 2 1 Read/Write Default Bit # Field Read/Write Default 13 12 11 10 Reserved 4 3 Port B Port A Port B Connect Port A Connect Wake Interrupt Wake Interrupt Change Change Enable Enable Interrupt Interrupt Enable Enable 9 8 SOF/EOP Interrupt Enable Reserved Reserved 0 Done Interrupt Enable R/W R/W R/W R/W - - - R/W 0 0 0 0 0 0 0 0 Register Description 1: Enable VBUS interrupt The Host n Interrupt Enable register enables control over host related interrupts. 0: Disable VBUS interrupt In this register a bit set to ‘1’ enables the corresponding interrupt while ‘0’ disables the interrupt. VBUS Interrupt Enable (Bit 15) The VBUS Interrupt Enable bit enables or disables the OTG VBUS interrupt. When enabled this interrupt triggers on both the rising and falling edge of VBUS at the 4.4V status (only supported in Port 1A). This bit is only available for Host 1 and is a reserved bit in Host 2. Document #: 38-08015 Rev. *K ID Interrupt Enable (Bit 14) The ID Interrupt Enable bit enables or disables the OTG ID interrupt. When enabled this interrupt triggers on both the rising and falling edge of the OTG ID pin (only supported in Port 1A). This bit is only available for Host 1 and is a reserved bit in Host 2. 1: Enable ID interrupt 0: Disable ID interrupt Page 35 of 102 [+] Feedback CY7C67300 SOF/EOP Interrupt Enable (Bit 9) 1: Enable Connect Change interrupt The SOF/EOP Interrupt Enable bit enables or disables the SOF/EOP timer interrupt 0: Disable Connect Change interrupt Port A Connect Change Interrupt Enable (Bit 4) 1: Enable SOF/EOP timer interrupt The Port A Connect Change Interrupt Enable bit enables or disables the Connect Change interrupt on Port A. This interrupt triggers when either a device is inserted (SE0 state to J state) or a device is removed (J state to SE0 state). 0: Disable SOF/EOP timer interrupt Port B Wake Interrupt Enable (Bit 7) The Port B Wake Interrupt Enable bit enables or disables the remote wakeup interrupt for Port B 1: Enable Connect Change interrupt 0: Disable Connect Change interrupt 1: Enable remote wakeup interrupt for Port B 0: Disable remote wakeup interrupt for Port B Done Interrupt Enable (Bit 0) Port A Wake Interrupt Enable (Bit 6) 1: Enable remote wakeup interrupt for Port A The Done Interrupt Enable bit enables or disables the USB Transfer Done interrupt. The USB Transfer Done triggers when either the host responds with an ACK, or a device responds with any of the following: ACK, NAK, STALL, or Timeout. This interrupt is used for both Port A and Port B. 0: Disable remote wakeup interrupt for Port A 1: Enable USB Transfer Done interrupt The Port A Wake Interrupt Enable bit enables or disables the remote wakeup interrupt for Port A 0: Disable USB Transfer Done interrupt Port B Connect Change Interrupt Enable (Bit 5) Reserved The Port B Connect Change Interrupt Enable bit enables or disables the Port B Connect Change interrupt on Port B. This interrupt triggers when either a device is inserted (SE0 state to J state) or a device is removed (J state to SE0 state). Write all reserved bits with ’0’. Host n Status Register [R/W] ■ Host 1 Status Register 0xC090 ■ Host 2 Status Register 0xC0B0 Table 58. Host n Status Register Bit # 15 14 Field VBUS Interrupt Flag ID Interrupt Flag R/W R/W - - - X X X X X Read/Write Default 13 7 6 Field Port B Wake Interrupt Flag Port A Wake Interrupt Flag R/W R/W R/W X X X Default 11 10 9 8 SOF/EOP Interrupt Flag Reserved - R/W - X X X Reserved Bit # Read/Write 12 5 4 3 2 1 0 Port B SE0 Status Port A SE0 Status Reserved Done Interrupt Flag R/W R/W R/W - R/W X X X X X Port B Connect Port A Connect Change Change Interrupt Interrupt Flag Flag Register Description 1: Interrupt triggered The Host n Status register provides status information for host operation. Pending interrupts can be cleared by writing a ‘1’ to the corresponding bit. This register can be accessed by the HPI interface. 0: Interrupt did not trigger VBUS Interrupt Flag (Bit 15) The VBUS Interrupt Flag bit indicates the status of the OTG VBUS interrupt (only for Port 1A). When enabled this interrupt triggers on both the rising and falling edge of VBUS at 4.4V. This bit is only available for Host 1 and is a reserved bit in Host 2. Document #: 38-08015 Rev. *K ID Interrupt Flag (Bit 14) The ID Interrupt Flag bit indicates the status of the OTG ID interrupt (only for Port 1A). When enabled this interrupt triggers on both the rising and falling edge of the OTG ID pin. This bit is only available for Host 1 and is a reserved bit in Host 2. 1: Interrupt triggered 0: Interrupt did not trigger Page 36 of 102 [+] Feedback CY7C67300 The SOF/EOP Interrupt Flag bit indicates the status of the SOF/EOP Timer interrupt. This bit triggers ‘1’ when the SOF/EOP timer expires. triggers ‘1’ on either a rising edge or falling edge of a USB Reset condition (device inserted or removed). Together with the Port A SE0 Status bit, it can be determined whether a device was inserted or removed. 1: Interrupt triggered 1: Interrupt triggered 0: Interrupt did not trigger 0: Interrupt did not trigger Port B Wake Interrupt Flag (Bit 7) Port B SE0 Status (Bit 3) The Port B Wake Interrupt Flag bit indicates remote wakeup on PortB. 1: Interrupt triggered The Port B SE0 Status bit indicates if Port B is in a SE0 state or not. Together with the Port B Connect Change Interrupt Flag bit, it can be determined whether a device was inserted (non-SE0 condition) or removed (SE0 condition). 0: Interrupt did not trigger 1: SE0 condition Port A Wake Interrupt Flag (Bit 6) 0: Non-SE0 condition SOF/EOP Interrupt Flag (Bit 9) The Port A Wake Interrupt Flag bit indicates remote wakeup on PortA. Port A SE0 Status (Bit 2) The Port A SE0 Status bit indicates if Port A is in a SE0 state or not. Together with the Port A Connect change Interrupt Flag bit, it can be determined whether a device was inserted (non-SE0 condition) or removed (SE0 condition). 1: Interrupt triggered 0: Interrupt did not trigger Port B Connect Change Interrupt Flag (Bit 5) 1: SE0 condition The Port B Connect Change Interrupt Flag bit indicates the status of the Connect Change interrupt on Port B. This bit triggers ‘1’ on either a rising edge or falling edge of a USB Reset condition (device inserted or removed). Together with the Port B SE0 Status bit, it can be determined whether a device was inserted or removed. 0: Non-SE0 condition Done Interrupt Flag (Bit 0) The Done Interrupt Flag bit indicates the status of the USB Transfer Done interrupt. The USB Transfer Done triggers when either the host responds with an ACK, or a device responds with any of the following: ACK, NAK, STALL, or Timeout. This interrupt is used for both Port A and Port B. 1: Interrupt triggered 0: Interrupt did not trigger 1: Interrupt triggered Port A Connect Change Interrupt Flag (Bit 4) 0: Interrupt did not trigger The Port A Connect Change Interrupt Flag bit indicates the status of the Connect Change interrupt on Port A. This bit Host n SOF/EOP Count Register [R/W] ■ Host 1 SOF/EOP Count Register 0xC092 ■ Host 2 SOF/EOP Count Register 0xC0B2 Table 59. Host n SOF/EOP Count Register Bit # 15 Field 14 13 12 11 Reserved 10 9 8 Count... Read/Write - - R/W R/W R/W R/W R/W R/W Default 0 0 1 0 1 1 1 0 Bit # 7 6 5 4 3 2 1 0 Field Read/Write Default ...Count R/W R/W R/W R/W R/W R/W R/W R/W 1 1 1 0 0 0 0 0 Register Description The Host n SOF/EOP Count register contains the SOF/EOP Count Value that is loaded into the SOF/EOP counter. This value is loaded each time the SOF/EOP counter counts down to zero. The default value set in this register at power up is 0x2EE0 which generates a 1 ms time frame. The SOF/EOP counter is a down counter decremented at a 12 MHz rate. When this register is Document #: 38-08015 Rev. *K read, the value returned is the programmed SOF/EOP count value. Count (Bits [13:0]) The Count field sets the SOF/EOP counter duration. Reserved Write all reserved bits with ’0’. Page 37 of 102 [+] Feedback CY7C67300 Host n SOF/EOP Counter Register [R] ■ Host 1 SOF/EOP Counter Register 0xC094 ■ Host 2 SOF/EOP Counter Register 0xC0B4 Table 60. Host n SOF/EOP Counter Register Bit # 15 Field 14 13 12 11 Reserved 10 9 8 Counter... Read/Write - - R R R R R R Default X X X X X X X X Bit # 7 6 5 4 3 2 1 0 Read/Write R R R R R R R R Default X X X X X X X X Field ...Counter Register Description Counter (Bits [13:0]) The Host n SOF/EOP Counter register contains the current value of the SOF/EOP down counter. This value can be used to determine the time remaining in the current frame. The Counter field contains the current value of the SOF/EOP down counter. Host n Frame Register [R] ■ Host 1 Frame Register 0xC096 ■ Host 2 Frame Register 0xC0B6 Table 61. Host n Frame Register Bit # 15 14 Field 13 12 11 10 Reserved 9 8 Frame... Read/Write - - - - - R R R Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field ...Frame Read/Write R R R R R R R R Default 0 0 0 0 0 0 0 0 Register Description Frame (Bits [10:0]) The Host n Frame register maintains the next frame number to be transmitted (current frame number + 1). This value is updated after each SOF transmission. This register resets to 0x0000 after each CPU write to the Host n SOF/EOP Count register (Host 1: 0xC092 Host 2: 0xC0B2). The Frame field contains the next frame number to be transmitted. Document #: 38-08015 Rev. *K Reserved Write all reserved bits with ’0’. Page 38 of 102 [+] Feedback CY7C67300 USB Device Only Registers There are eleven sets of USB Device Only registers. All sets consist of at least two registers, one for Device Port 1 and one for Device Port 2. In addition, each Device port has eight possible endpoints. This gives each endpoint register set eight registers for each Device Port for a total of sixteen registers per set. The USB Device Only registers are covered in this section and summarized in Table 62. Table 62. USB Device Only Registers Register Name Address (Device 1/Device 2) R/W Device n Endpoint n Control Register 0x02n0 R/W Device n Endpoint n Address Register 0x02n2 R/W Device n Endpoint n Count Register 0x02n4 R/W Device n Endpoint n Status Register 0x02n6 R/W Device n Endpoint n Count Result Register 0x02n8 R/W Device n Port Select Register 0xC084/0xC0A4 R/W Device n Interrupt Enable Register 0xC08C/0xC0AC R/W Device n Address Register 0xC08E/0xC0AE R/W Device n Status Register 0xC090/0xCB0 R/W Device n Frame Number Register 0xC092/0xC0B2 R Device n SOF/EOP Count Register 0xC094/0xC0B4 W Device n Endpoint n Control Register [R/W] ■ Device n Endpoint 0 Control Register [Device 1: 0x0200 Device 2: 0x0280] ■ Device n Endpoint 1 Control Register [Device 1: 0x0210 Device 2: 0x0290] ■ Device n Endpoint 2 Control Register [Device 1: 0x0220 Device 2: 0x02A0] ■ Device n Endpoint 3 Control Register [Device 1: 0x0230 Device 2: 0x02B0] ■ Device n Endpoint 4 Control Register [Device 1: 0x0240 Device 2: 0x02C0] ■ Device n Endpoint 5 Control Register [Device 1: 0x0250 Device 2: 0x02D0] ■ Device n Endpoint 6 Control Register [Device 1: 0x0260 Device 2: 0x02E0] ■ Device n Endpoint 7 Control Register [Device 1: 0x0270 Device 2: 0x02F0] Table 63. Device n Endpoint n Control Register Bit # 15 14 13 12 Field 11 10 9 8 Reserved Read/Write - - - - - - - - Default X X X X X X X X Bit # 7 6 5 4 3 2 1 0 Sequence Select Stall Enable ISO Enable NAK Interrupt Enable Direction Select Enable Arm Enable Field IN/OUT Ignore Enable R/W R/W R/W R/W R/W R/W R/W R/W X X X X X X X X Read/Write Default Register Description IN/OUT Ignore Enable (Bit 7) The Device n Endpoint n Control register provides control over a single EP in device mode. There are a total of eight endpoints for each of the two ports. All endpoints have the same definition for their Device n Endpoint n Control register. The IN/OUT Ignore Enable bit forces endpoint 0 (EP0) to ignore all IN and OUT requests. Set this bit so that EP0 only accepts Setup packets at the start of each transfer. Clear this bit to accept IN/OUT transactions. This bit only applies to EP0. 1: Ignore IN/OUT requests 0: Do not ignore IN/OUT requests Document #: 38-08015 Rev. *K Page 39 of 102 [+] Feedback CY7C67300 Sequence Select (Bit 6) Direction Select (Bit 2) The Sequence Select bit determines whether a DATA0 or a DATA1 is sent for the next data toggle. This bit has no effect on receiving data packets; sequence checking must be handled in firmware. 1: Send a DATA1 0: Send a DATA0 The Direction Select bit needs to be set according to the expected direction of the next data stage in the next transaction. If the data stage direction is different from what is set in this bit, it gets NAKed and either the IN Exception Flag or the OUT Exception Flag is set in the Device n Endpoint n Status register. If a setup packet is received and the Direction Select bit is set incorrectly, the setup is ACKed and the Setup Status Flag is set (refer to the setup bit of the Device n Endpoint n Status Register [R/W] on page 42 for details). Stall Enable (Bit 5) The Stall Enable bit sends a Stall in response to the next request (unless it is a setup request, which are always ACKed). This is a sticky bit and continues to respond with Stalls until cleared by firmware. 1: Send Stall 0: Do not send Stall ISO Enable (Bit 4) The ISO Enable bit enables and disables an isochronous transaction. This bit is only valid for EPs 1–7 and has no function for EP0. 1: Enable isochronous transaction 0: Disable isochronous transaction NAK Interrupt Enable (Bit 3) The NAK Interrupt Enable bit enables and disables the generation of an Endpoint n interrupt when the device responds to the host with a NAK. The Endpoint n Interrupt Enable bit in the Device n Interrupt Enable register must also be set. When a NAK is sent to the host, the corresponding EP Interrupt Flag in the Device n Status register is set. In addition, the NAK Flag in the Device n Endpoint n Status register is set. 1: Enable NAK interrupt 0: Disable NAK interrupt 1: OUT transfer (host to device) 0: IN transfer (device to host) Enable (Bit 1) Set the Enable bit to allow transfers to the endpoint. If Enable is set to ‘0’ then all USB traffic to this endpoint is ignored. If Enable is set ‘1’ and Arm Enable (bit 0) is set ‘0’ then NAKs are automatically returned from this endpoint (except setup packets which are always ACKed as long as the Enable bit is set). 1: Enable transfers to an endpoint 0: Do not allow transfers to an endpoint Arm Enable (Bit 0) The Arm Enable bit arms the endpoint to transfer or receive a packet. This bit is cleared to ‘0’ when a transaction is complete. 1: Arm endpoint 0: Endpoint disarmed Reserved Write all reserved bits with ’0’. Device n Endpoint n Address Register [R/W] ■ Device n Endpoint 0 Address Register [Device 1: 0x0202 Device 2: 0x0282] ■ Device n Endpoint 1 Address Register [Device 1: 0x0212 Device 2: 0x0292] ■ Device n Endpoint 2 Address Register [Device 1: 0x0222 Device 2: 0x02A2] ■ Device n Endpoint 3 Address Register [Device 1: 0x0232 Device 2: 0x02B2] ■ Device n Endpoint 4 Address Register [Device 1: 0x0242 Device 2: 0x02C2] ■ Device n Endpoint 5 Address Register [Device 1: 0x0252 Device 2: 0x02D2] ■ Device n Endpoint 6 Address Register [Device 1: 0x0262 Device 2: 0x02E2] ■ Device n Endpoint 7 Address Register [Device 1: 0x0272 Device 2: 0x02F2] Table 64. Device n Endpoint n Address Register Bit # 15 14 13 12 Field Read/Write 11 10 9 8 Address... R/W R/W R/W R/W R/W R/W R/W R/W Default X X X X X X X X Bit # 7 6 5 4 3 2 1 0 Field Read/Write Default ...Address R/W R/W R/W R/W R/W R/W R/W R/W X X X X X X X X Document #: 38-08015 Rev. *K Page 40 of 102 [+] Feedback CY7C67300 Register Description Address (Bits [15:0]) The Device n Endpoint n Address register is used as the base pointer into memory space for the current Endpoint transaction. There are a total of eight endpoints for each of the two ports. All endpoints have the same definition for their Device n Endpoint n Address register. The Address field sets the base address for the current transaction on a signal endpoint. Device n Endpoint n Count Register [R/W] ■ Device n Endpoint 0 Count Register [Device 1: 0x0204 Device 2: 0x0284] ■ Device n Endpoint 1 Count Register [Device 1: 0x0214 Device 2: 0x0294] ■ Device n Endpoint 2 Count Register [Device 1: 0x0224 Device 2: 0x02A4] ■ Device n Endpoint 3 Count Register [Device 1: 0x0234 Device 2: 0x02B4] ■ Device n Endpoint 4 Count Register [Device 1: 0x0244 Device 2: 0x02C4] ■ Device n Endpoint 5 Count Register [Device 1: 0x0254 Device 2: 0x02D4] ■ Device n Endpoint 6 Count Register [Device 1: 0x0264 Device 2: 0x02E4] ■ Device n Endpoint 7 Count Register [Device 1: 0x0274 Device 2: 0x02F4] Table 65. Device n Endpoint n Count Register Bit # 15 14 13 Field 12 11 10 9 Reserved 8 Count... Read/Write - - - - - - R/W R/W Default X X X X X X X X Bit # 7 6 5 4 3 2 1 0 Field Read/Write Default ...Count R/W R/W R/W R/W R/W R/W R/W R/W X X X X X X X X Register Description Count (Bits [9:0]) The Device n Endpoint n Count register designates the maximum packet size that can be received from the host for OUT transfers for a single endpoint. This register also designates the packet size to be sent to the host in response to the next IN token for a single endpoint. The maximum packet length is 1023 bytes in ISO mode. There are a total of eight endpoints for each of the two ports. All endpoints have the same definition for their Device n Endpoint n Count register. The Count field sets the current transaction packet length for a single endpoint. Document #: 38-08015 Rev. *K Reserved Write all reserved bits with ’0’. Page 41 of 102 [+] Feedback CY7C67300 Device n Endpoint n Status Register [R/W] ■ Device n Endpoint 0 Status Register [Device 1: 0x0206 Device 2: 0x0286] ■ Device n Endpoint 1 Status Register [Device 1: 0x0216 Device 2: 0x0296] ■ Device n Endpoint 2 Status Register [Device 1: 0x0226 Device 2: 0x02A6] ■ Device n Endpoint 3 Status Register [Device 1: 0x0236 Device 2: 0x02B6] ■ Device n Endpoint 4 Status Register [Device 1: 0x0246 Device 2: 0x02C6] ■ Device n Endpoint 5 Status Register [Device 1: 0x0256 Device 2: 0x02D6] ■ Device n Endpoint 6 Status Register [Device 1: 0x0266 Device 2: 0x02E6] ■ Device n Endpoint 7 Status Register [Device 1: 0x0276 Device 2: 0x02F6] Table 66. Device n Endpoint n Status Register Bit # 15 14 13 12 Reserved Field 11 10 9 Overflow Flag Underflow Flag 8 OUT IN Exception Flag Exception Flag Read/Write - - - - R/W R/W R/W R/W Default X X X X X X X X Bit # 7 6 5 4 3 2 1 0 Field Stall Flag NAK Flag Length Exception Flag Setup Flag Sequence Flag Timeout Flag Error Flag ACK Flag Read/Write R/W R/W R/W R/W R/W R/W R/W R/W X X X X X X X X Default Register Description OUT Exception Flag (Bit 9) The Device n Endpoint n Status register provides packet status information for the last transaction received or transmitted. This register is updated in hardware and does not need to be cleared by firmware. There are a total of eight endpoints for each of the two ports. All endpoints have the same definition for their Device n Endpoint n Status register. The OUT Exception Flag bit indicates when the device received an OUT packet when armed for an IN. 1: Received OUT when armed for IN 0: Received IN when armed for IN IN Exception Flag (Bit 8) The Device n Endpoint n Status register is a memory based register that must be initialized to 0x0000 before USB Device operations are initiated. After initialization, do not write to this register again. The IN Exception Flag bit indicates when the device received an IN packet when armed for an OUT. Overflow Flag (Bit 11) 0: Received OUT when armed for OUT The Overflow Flag bit indicates that the received data in the last data transaction exceeded the maximum length specified in the Device n Endpoint n Count register. The Overflow Flag must be checked in response to a Length Exception signified by the Length Exception Flag set to ‘1’. Stall Flag (Bit 7) The Stall Flag bit indicates that a Stall packet was sent to the host. 1: Overflow condition occurred 0: Stall packet was not sent 1: Received IN when armed for OUT 1: Stall packet was sent to the host 0: Overflow condition did not occur NAK Flag (Bit 6) Underflow Flag (Bit 10) The NAK Flag bit indicates that a NAK packet was sent to the host. The Underflow Flag bit indicates that the received data in the last data transaction was less then the maximum length specified in the Device n Endpoint n Count register. The Underflow Flag must be checked in response to a Length Exception signified by the Length Exception Flag set to ‘1’. 1: Underflow condition occurred 0: Underflow condition did not occur Document #: 38-08015 Rev. *K 1: NAK packet was sent to the host 0: NAK packet was not sent Length Exception Flag (Bit 5) The Length Exception Flag bit indicates the received data in the data stage of the last transaction does not equal the maximum Endpoint Count specified in the Device n Endpoint n Count register. A Length Exception can either mean an overflow or Page 42 of 102 [+] Feedback CY7C67300 underflow and the Overflow and Underflow flags (bits 11 and 10 respectively) must be checked to determine which event occurred. 1: An overflow or underflow condition occurred 0: An overflow or underflow condition did not occur Setup Flag (Bit 4) The Setup Flag bit indicates that a setup packet was received. In device mode setup packets are stored at memory location 0x0300 for Device 1 and 0x0308 for Device 2. Setup packets are always accepted regardless of the Direction Select and Arm Enable bit settings as long as the Device n EP n Control register Enable bit is set. Timeout Flag (Bit 2) The Timeout Flag bit indicates whether a timeout condition occurred on the last transaction. On the device side, a timeout can occur if the device sends a data packet in response to an IN request but then does not receive a handshake packet in a predetermined time. It can also occur if the device does not receive the data stage of an OUT transfer in time. 1: Timeout occurred 0: Timeout condition did not occur Error Flag (Bit 2) 1: Setup packet was received The Error Flag bit is set if a CRC5 and CRC16 error occurs, or if an incorrect packet type is received. Overflow and underflow are not considered errors and do not affect this bit. 0: Setup packet was not received 1: Error occurred Sequence Flag (Bit 3) 0: Error did not occur The Sequence Flag bit indicates whether the last data toggle received was a DATA1 or a DATA0. This bit has no effect on receiving data packets; sequence checking must be handled in firmware. The ACK Flag bit indicates whether the last transaction was ACKed. ACK Flag (Bit 0) 1: ACK occurred 1: DATA1 was received 0: ACK did not occur 0: DATA0 was received Device n Endpoint n Count Result Register [R/W] ■ Device n Endpoint 0 Count Result Register [Device 1: 0x0208 Device 2: 0x0288] ■ Device n Endpoint 1 Count Result Register [Device 1: 0x0218 Device 2: 0x0298] ■ Device n Endpoint 2 Count Result Register [Device 1: 0x0228 Device 2: 0x02A8] ■ Device n Endpoint 3 Count Result Register [Device 1: 0x0238 Device 2: 0x02B8] ■ Device n Endpoint 4 Count Result Register [Device 1: 0x0248 Device 2: 0x02C8] ■ Device n Endpoint 5 Count Result Register [Device 1: 0x0258 Device 2: 0x02D8] ■ Device n Endpoint 6 Count Result Register [Device 1: 0x0268 Device 2: 0x02E8] ■ Device n Endpoint 7 Count Result Register [Device 1: 0x0278 Device 2: 0x02F8] Table 67. Device n Endpoint n Count Result Register Bit # 15 14 13 12 Field Read/Write 11 10 9 8 Result... R/W R/W R/W R/W R/W R/W R/W R/W Default X X X X X X X X Bit # 7 6 5 4 3 2 1 0 Field Read/Write Default ...Result R/W R/W R/W R/W R/W R/W R/W R/W X X X X X X X X Register Description The Device n Endpoint n Count Result register contains the size difference in bytes between the Endpoint Count specified in the Device n Endpoint n Count register and the last packet received. If an overflow or underflow condition occurs, that is, the received packet length differs from the value specified in the Device n Document #: 38-08015 Rev. *K Endpoint n Count register, the Length Exception Flag bit in the Device n Endpoint n Status register is set. The value in this register is only valued when the Length Exception Flag bit is set and the Error Flag bit is not set; both bits are in the Device n Endpoint n Status register. Page 43 of 102 [+] Feedback CY7C67300 The Device n Endpoint n Count Result register is a memory-based register that must be initialized to 0x0000 before USB Device operations are initiated. After initialization, do not write to this register again. additional byte count of the received packet. If an underflow condition occurs, Result [15:0] indicates the excess bytes count (number of bytes not used). Reserved Result (Bits [15:0]) Write all reserved bits with ‘0’. The Result field contains the differences in bytes between the received packet and the value specified in the Device n Endpoint n Count register. If an overflow condition occurs, Result [15:10] is set to ‘111111’, a 2’s complement value indicating the Device n Port Select Register [R/W] ■ Device n Port Select Register 0xC084 ■ Device n Port Select Register 0xC0A4 Table 68. Device n Port Select Register Bit # 15 14 Reserved Port Select Read/Write - R/W - - - - - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Field 13 12 11 10 9 8 Reserved... Field ...Reserved Register Description Port Select (Bit 14) The Device n Port Select register selects either port A or port B for the static device port. 1: Port 1B or Port 2B is enabled The Port Select bit selects which of the two ports is enabled. 0: Port 1A or Port 2A is enabled Device n Interrupt Enable Register [R/W] ■ Device 1 Interrupt Enable Register 0xC08C ■ Device 2 Interrupt Enable Register 0xC0AC Table 69. Device n Interrupt Enable Register Bit # 15 14 VBUS Interrupt Enable ID Interrupt Enable 13 R/W R/W - 0 0 0 12 11 10 9 8 SOF/EOP Timeout Interrupt Enable Reserved SOF/EOP Interrupt Enable Reset Interrupt Enable - R/W - R/W R/W 0 0 0 0 0 Reserved Field Read/Write Default Bit # 7 6 5 4 3 2 1 0 Field EP7 Interrupt Enable EP6 Interrupt Enable EP5 Interrupt Enable EP4 Interrupt Enable EP3 Interrupt Enable EP2 Interrupt Enable EP1 Interrupt Enable EP0 Interrupt Enable R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Read/Write Default Register Description VBUS Interrupt Enable (Bit 15) The Device n Interrupt Enable register provides control over device related interrupts including eight different endpoint interrupts. The VBUS Interrupt Enable bit enables or disables the OTG VBUS interrupt. When enabled, this interrupt triggers on both the rising and falling edge of VBUS at the 4.4V status (only Document #: 38-08015 Rev. *K Page 44 of 102 [+] Feedback CY7C67300 supported in Port 1A). This bit is only available for Device 1 and is a reserved bit in Device 2. Enable bit in the Device n Endpoint Control register can also be set so that NAK responses trigger this interrupt. 1: Enable VBUS interrupt 1: Enable EP6 Transaction Done interrupt 0: Disable VBUS interrupt 0: Disable EP6 Transaction Done interrupt ID Interrupt Enable (Bit 14) EP5 Interrupt Enable (Bit 5) The ID Interrupt Enable bit enables or disables the OTG ID interrupt. When enabled, this interrupt triggers on both the rising and falling edge of the OTG ID pin (only supported in Port 1A). This bit is only available for Device 1 and is a reserved bit in Device 2. The EP5 Interrupt Enable bit enables or disables endpoint five (EP5) Transaction Done interrupt. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied Endpoint: send/receive ACK, send STALL, Timeout occurs, IN Exception Error, or OUT Exception Error. In addition, the NAK Interrupt Enable bit in the Device n Endpoint Control register can also be set so that NAK responses trigger this interrupt. 1: Enable EP5 Transaction Done interrupt 0: Disable EP5 Transaction Done interrupt 1: Enable ID interrupt 0: Disable ID interrupt SOF/EOP Timeout Interrupt Enable (Bit 11) The SOF/EOP Timeout Interrupt Enable bit enables or disables the SOF/EOP Timeout Interrupt. When enabled this interrupt triggers when the USB host fails to send a SOF or EOP packet within the time period specified in the Device n SOF/EOP Count register. In addition, the Device n Frame register counts the number of times the SOF/EOP Timeout Interrupt triggers between receiving SOF/EOPs. 1: SOF/EOP timeout occurred 0: SOF/EOP timeout did not occur SOF/EOP Interrupt Enable (Bit 9) The SOF/EOP Interrupt Enable bit enables or disables the SOF/EOP received interrupt. EP4 Interrupt Enable (Bit 4) The EP4 Interrupt Enable bit enables or disables endpoint four (EP4) Transaction Done interrupt. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied Endpoint: send/receive ACK, send STALL, Timeout occurs, IN Exception Error, or OUT Exception Error. In addition, the NAK Interrupt Enable bit in the Device n Endpoint Control register can also be set so that NAK responses trigger this interrupt. 1: Enable EP4 Transaction Done interrupt 0: Disable EP4 Transaction Done interrupt 1: Enable SOF/EOP received interrupt EP3 Interrupt Enable (Bit 3) 0: Disable SOF/EOP received interrupt The EP3 Interrupt Enable bit enables or disables endpoint three (EP3) Transaction Done interrupt. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied Endpoint: send/receive ACK, send STALL, Timeout occurs, IN Exception Error, or OUT Exception Error. In addition, the NAK Interrupt Enable bit in the Device n Endpoint Control register can also be set so that NAK responses trigger this interrupt. 1: Enable EP3 Transaction Done interrupt 0: Disable EP3 Transaction Done interrupt Reset Interrupt Enable (Bit 8) The Reset Interrupt Enable bit enables or disables the USB Reset Detected interrupt 1: Enable USB Reset Detected interrupt 0: Disable USB Reset Detected interrupt EP7 Interrupt Enable (Bit 7) The EP7 Interrupt Enable bit enables or disables endpoint seven (EP7) Transaction Done interrupt. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied Endpoint: send/receive ACK, send STALL, Timeout occurs, IN Exception Error, or OUT Exception Error. In addition, the NAK Interrupt Enable bit in the Device n Endpoint Control register can also be set so that NAK responses trigger this interrupt. 1: Enable EP7 Transaction Done interrupt 0: Disable EP7 Transaction Done interrupt EP6 Interrupt Enable (Bit 6) The EP6 Interrupt Enable bit enables or disables endpoint six (EP6) Transaction Done interrupt. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied Endpoint: send/receive ACK, send STALL, Timeout occurs, IN Exception Error, or OUT Exception Error. In addition, the NAK Interrupt Document #: 38-08015 Rev. *K EP2 Interrupt Enable (Bit 2) The EP2 Interrupt Enable bit enables or disables endpoint two (EP2) Transaction Done interrupt. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied Endpoint: send/receive ACK, send STALL, Timeout occurs, IN Exception Error, or OUT Exception Error. In addition, the NAK Interrupt Enable bit in the Device n Endpoint Control register can also be set so that NAK responses trigger this interrupt. 1: Enable EP2 Transaction Done interrupt 0: Disable EP2 Transaction Done interrupt EP1 Interrupt Enable (Bit 1) The EP1 Interrupt Enable bit enables or disables endpoint one (EP1) Transaction Done interrupt. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied Endpoint: send/receive ACK, send STALL, Timeout occurs, IN Exception Page 45 of 102 [+] Feedback CY7C67300 Error, or OUT Exception Error. In addition, the NAK Interrupt Enable bit in the Device n Endpoint Control register can also be set so that NAK responses trigger this interrupt. 1: Enable EP1 Transaction Done interrupt 0: Disable EP1 Transaction Done interrupt send/receive ACK, send STALL, Timeout occurs, IN Exception Error, or OUT Exception Error. In addition, the NAK Interrupt Enable bit in the Device n Endpoint Control register can also be set so that NAK responses trigger this interrupt. 1: Enable EP0 Transaction Done interrupt 0: Disable EP0 Transaction Done interrupt EP0 Interrupt Enable (Bit 0) Reserved The EP0 Interrupt Enable bit enables or disables endpoint zero (EP0) Transaction Done interrupt. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied Endpoint: Write all reserved bits with ’0’. Device n Address Register [W] ■ Device 1 Address Register 0xC08E ■ Device 2 Address Register 0xC0AE Table 70. Device n Address Register Bit # 15 14 13 12 Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field ...Reserved Field 11 10 9 8 Reserved... Address Read/Write - W W W W W W W Default 0 0 0 0 0 0 0 0 Register Description Address (Bits [6:0]) The Device n Address register holds the device address assigned by the host. This register initializes to the default address 0 at reset but must be updated by firmware when the host assigns a new address. Only USB data sent to the address contained in this register gets a respond—all others are ignored. The Address field contains the USB address of the device assigned by the host. Reserved Write all reserved bits with ’0’. Device n Status Register [R/W] ■ Device 1 Status Register 0xC090 ■ Device 2 Status Register 0xC0B0 Table 71. Device n Status Register Bit # 15 14 ID Interrupt Flag Field VBUS Interrupt Flag R/W R/W - - - - R/W R/W X X X X X X X X Read/Write Default 13 12 11 10 Reserved 9 8 SOF/EOP Reset Interrupt Interrupt Flag Flag Bit # 7 6 5 4 3 2 1 0 Field EP7 Interrupt Flag EP6 Interrupt Flag EP5 Interrupt Flag EP4 Interrupt Flag EP3 Interrupt Flag EP2 Interrupt Flag EP1 Interrupt Flag EP0 Interrupt Flag R/W R/W R/W R/W R/W R/W R/W R/W X X X X X X X X Read/Write Default Document #: 38-08015 Rev. *K Page 46 of 102 [+] Feedback CY7C67300 Register Description EP6 Interrupt Flag (Bit 6) The Device n Status register provides status information for device operation. Pending interrupts can be cleared by writing a ‘1’ to the corresponding bit. This register can be accessed by the HPI interface. The EP6 Interrupt Flag bit indicates if the endpoint six (EP6) Transaction Done interrupt triggered. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied EP: send/receive ACK, send STALL, Timeout occurs, IN Exception Error, or OUT Exception Error. In addition, if the NAK Interrupt Enable bit in the Device n Endpoint Control register is set, this interrupt also triggers when the device NAKs host requests. VBUS Interrupt Flag (Bit 15) The VBUS Interrupt Flag bit indicates the status of the OTG VBUS interrupt (only for Port 1A). When enabled this interrupt triggers on both the rising and falling edge of VBUS at 4.4V. This bit is only available for Device 1 and is a reserved bit in Device 2. 1: Interrupt triggered 0: Interrupt did not trigger 1: Interrupt triggered 0: Interrupt did not trigger EP5 Interrupt Flag (Bit 5) 1: Interrupt triggered The EP5 Interrupt Flag bit indicates if the endpoint five (EP5) Transaction Done interrupt triggered. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied EP: send/receive ACK, send STALL, Timeout occurs, IN Exception Error, or OUT Exception Error. In addition, if the NAK Interrupt Enable bit in the Device n Endpoint Control register is set, this interrupt also triggers when the device NAKs host requests. 0: Interrupt did not trigger 1: Interrupt triggered SOF/EOP Interrupt Flag (Bit 9) 0: Interrupt did not trigger The SOF/EOP Interrupt Flag bit indicates if the SOF/EOP received interrupt triggered. EP4 Interrupt Flag (Bit 4) ID Interrupt Flag (Bit 14) The ID Interrupt Flag bit indicates the status of the OTG ID interrupt (only for Port 1A). When enabled this interrupt triggers on both the rising and falling edge of the OTG ID pin. This bit is only available for Device 1 and is a reserved bit in Device 2. 1: Interrupt triggered 0: Interrupt did not trigger Reset Interrupt Flag (Bit 8) The Reset Interrupt Flag bit indicates if the USB Reset Detected interrupt triggered. 1: Interrupt triggered 0: Interrupt did not trigger EP7 Interrupt Flag (Bit 7) The EP7 Interrupt Flag bit indicates if the endpoint seven (EP7) Transaction Done interrupt triggered. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied EP: send/receive ACK, send STALL, Timeout occurs, IN Exception Error, or OUT Exception Error. In addition, if the NAK Interrupt Enable bit in the Device n Endpoint Control register is set, this interrupt also triggers when the device NAKs host requests. 1: Interrupt triggered 0: Interrupt did not trigger Document #: 38-08015 Rev. *K The EP4 Interrupt Flag bit indicates if the endpoint four (EP4) Transaction Done interrupt triggered. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied EP: send/receive ACK, send STALL, Timeout occurs, IN Exception Error, or OUT Exception Error. In addition, if the NAK Interrupt Enable bit in the Device n Endpoint Control register is set, this interrupt also triggers when the device NAKs host requests. 1: Interrupt triggered 0: Interrupt did not trigger EP3 Interrupt Flag (Bit 3) The EP3 Interrupt Flag bit indicates if the endpoint three (EP3) Transaction Done interrupt triggered. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied EP: send/receive ACK, send STALL, Timeout occurs, IN Exception Error, or OUT Exception Error. In addition, if the NAK Interrupt Enable bit in the Device n Endpoint Control register is set, this interrupt also triggers when the device NAKs host requests. 1: Interrupt triggered 0: Interrupt did not trigger Page 47 of 102 [+] Feedback CY7C67300 EP2 Interrupt Flag (Bit 2) The EP2 Interrupt Flag bit indicates if the endpoint two (EP2) Transaction Done interrupt triggered. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied EP: send/receive ACK, send STALL, Timeout occurs, IN Exception Error, or OUT Exception Error. In addition, if the NAK Interrupt Enable bit in the Device n Endpoint Control register is set, this interrupt also triggers when the device NAKs host requests. 1: Interrupt triggered 0: Interrupt did not trigger EP1 Interrupt Flag (Bit 1) The EP1 Interrupt Flag bit indicates if the endpoint one (EP1) Transaction Done interrupt triggered. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied EP: send/receive ACK, send STALL, Timeout occurs, IN Exception Error, or OUT Exception Error. In addition, if the NAK Interrupt Enable bit in the Device n Endpoint Control register is set, this interrupt also triggers when the device NAKs host requests. 1: Interrupt triggered 0: Interrupt did not trigger EP0 Interrupt Flag (Bit 0) The EP0 Interrupt Flag bit indicates if the endpoint zero (EP0) Transaction Done interrupt triggered. An EPx Transaction Done interrupt triggers when any of the following responses or events occur in a transaction for the device’s supplied EP: send/receive ACK, send STALL, Timeout occurs, IN Exception Error, or OUT Exception Error. In addition, if the NAK Interrupt Enable bit in the Device n Endpoint Control register is set, this interrupt also triggers when the device NAKs host requests. 1: Interrupt triggered 0: Interrupt did not trigger Reserved Write all reserved bits with ’0’. Device n Frame Number Register [R] ■ Device 1 Frame Number Register 0xC092 ■ Device 2 Frame Number Register 0xC0B2 Table 72. Device n Frame Number Register Bit # 15 Field SOF/EOP Timeout Flag 14 13 12 SOF/EOP Timeout Interrupt Counter 11 10 Reserved 9 8 Frame... Read/Write R R R R - R R R Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Read/Write R R R R R R R R Default 0 0 0 0 0 0 0 0 Field ...Frame Register Description SOF/EOP Timeout Interrupt Counter (Bits [14:12]) The Device n Frame Number register is a read only register that contains the Frame number of the last SOF packet received. This register also contains a count of SOF/EOP Timeout occurrences. SOF/EOP Timeout Flag (Bit 15) The SOF/EOP Timeout Interrupt Counter field increments by 1 from 0 to 7 for each SOF/EOP Timeout Interrupt. This field resets to 0 when a SOF/EOP is received. This field is only updated when the SOF/EOP Timeout Interrupt Enable bit in the Device n Interrupt Enable register is set. The SOF/EOP Timeout Flag bit indicates when an SOF/EOP Timeout Interrupt occurs. Frame (Bits [10:0]) 1: An SOF/EOP Timeout interrupt occurred 0: An SOF/EOP Timeout interrupt did not occur Document #: 38-08015 Rev. *K The Frame field contains the frame number from the last received SOF packet in full-speed mode. This field no function for low-speed mode. If a SOF Timeout occurs, this field contains the last received Frame number. Page 48 of 102 [+] Feedback CY7C67300 Device n SOF/EOP Count Register [W] ■ Device 1 SOF/EOP Count Register 0xC094 ■ Device 2 SOF/EOP Count Register 0xC0B4 Table 73. Device n SOF/EOP Count Register Bit # 15 Field 14 13 12 11 Reserved 10 9 8 Count... Read/Write - - R R R R R R Default 0 0 1 0 1 1 1 0 Bit # 7 6 5 4 3 2 1 0 Read/Write R R R R R R R R Default 1 1 1 0 0 0 0 0 Field ...Count Register Description Reserved The Device n SOF/EOP Count register is written with the time expected between receiving a SOF/EOP. If the SOF/EOP counter expires before an SOF/EOP is received, an SOF/EOP Timeout Interrupt can be generated. The SOF/EOP Timeout Interrupt Enable and SOF/EOP Timeout Interrupt Flag are located in the Device n Interrupt Enable and Status registers respectively. Write all reserved bits with ’0’. Set the SOF/EOP count slightly greater than the expected SOF/EOP interval. The SOF/EOP counter decrements at a 12 MHz rate. Therefore, in the case of an expected 1 ms SOF/EOP interval, the SOF/EOP count is set slightly greater than 0x2EE0. OTG Control Registers There is one register dedicated for On-The-Go operation. This register is covered in this section and summarized in Table 74. Table 74. OTG Register Register Name OTG Control Register Address R/W C098H R/W Count (Bits [13:0]) The Count field contains the current value of the SOF/EOP down counter. At power up and reset, this value is set to 0x2EE0 and for expected 1 ms SOF/EOP intervals, this SOF/EOP count is increased slightly. OTG Control Register [0xC098] [R/W] Table 75. OTG Control Register Bit # 15 14 Reserved Field 13 12 VBUS Pull-up Enable Receive Disable 11 10 Charge Pump VBUS Enable Discharge Enable 9 8 D+ Pull-up Enable D– Pull-up Enable Read/Write - - R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 Field D+ Pull-down Enable D– Pull-down Enable R/W R/W - - 0 0 0 0 Read/Write Default 5 4 3 2 1 0 OTG Data Status ID Status VBUS Valid Flag - R R R 0 X X X Reserved Register Description VBUS Pull-up Enable (Bit 13) The OTG Control register allows control and monitoring over the OTG port on Port1A. Note that the D± pull up and pull down bits override the setting in the USB 0 Control register for this port. The VBUS Pull-up Enable bit enables or disables a 500 ohm pull up resistor onto OTG VBus. 1: 500 ohm pull up resistor enabled 0: 500 ohm pull up resistor disabled Document #: 38-08015 Rev. *K Page 49 of 102 [+] Feedback CY7C67300 Receive Disable (Bit 12) OTG Data Status (Bit 2) The Receive Disable bit enables or powers down (disables) the OTG receiver section. The OTG Data Status bit is a read only bit and indicates the TTL logic state of the OTG VBus pin. 1: OTG receiver powered down and disabled 1: OTG VBus is greater then 2.4V 0: OTG receiver enabled 0: OTG VBus is less then 0.8V Charge Pump Enable (Bit 11) ID Status (Bit 1) The Charge Pump Enable bit enables or disables the OTG VBus charge pump. The ID Status bit is a read only bit that indicates the state of the OTG ID pin on Port A. 1: OTG VBus charge pump enabled 1: OTG ID Pin is not connected directly to ground (>10K ohm) 0: OTG VBus charge pump disabled 0: OTG ID Pin is connected directly ground (< 10 ohm) VBUS Discharge Enable (Bit 10) VBUS Valid Flag (Bit 0) The VBUS Discharge Enable bit enables or disables a 2K ohm discharge pull down resistor onto OTG VBus. 1: 2K ohm pull down resistor enabled The VBUS Valid Flag bit indicates whether OTG VBus is greater then 4.4V. After turning on VBUS, firmware must wait at least 10 µs before this reading this bit. 0: 2K ohm pull down resistor disabled 1: OTG VBus is greater then 4.4V D+ Pull-up Enable (Bit 9) 0: OTG VBus is less then 4.4V The D+ Pull-up Enable bit enables or disables a pull up resistor on the OTG D+ data line. Reserved 1: OTG D+ dataline pull up resistor enabled GPIO Registers 0: OTG D+ dataline pull up resistor disabled D– Pull-up Enable (Bit 8) The D– Pull-up Enable bit enables or disables a pull up resistor on the OTG D– data line. 1: OTG D– dataline pull up resistor enabled Write all reserved bits with ’0’. There are seven registers dedicated for GPIO operations. These seven registers are covered in this section and summarized in Table 76. Table 76. GPIO Registers Register Name Address R/W 0: OTG D– dataline pull up resistor disabled GPIO Control Register 0xC006 R/W D+ Pull-down Enable (Bit 7) GPIO0 Output Data Register 0xC01E R/W The D+ Pull-down Enable bit enables or disables a pull down resistor on the OTG D+ data line. GPIO0 Input Data Register 0xC020 R GPIO0 Direction Register 0xC022 R/W GPIO1 Output Data Register 0xC024 R/W GPIO1 Input Data Register 0xC026 R GPIO1 Direction Register 0xC028 R/W 1: OTG D+ dataline pull down resistor enabled 0: OTG D+ dataline pull down resistor disabled D– Pull-down Enable (Bit 6) The D– Pull-down Enable bit enables or disables a pull down resistor on the OTG D– data line. 1: OTG D– dataline pull down resistor enabled 0: OTG D– dataline pull down resistor disabled Document #: 38-08015 Rev. *K Page 50 of 102 [+] Feedback CY7C67300 GPIO Control Register [0xC006] [R/W] Table 77. GPIO Control Register Bit # 15 14 Write Protect Enable UD Field Read/Write 13 12 Reserved 11 10 9 SAS Enable 8 Mode Select R/W R/W - - R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field HSS Enable HSS XD Enable SPI Enable SPI XD Enable Interrupt 1 Polarity Select Interrupt 1 Enable Interrupt 0 Polarity Select Interrupt 0 Enable R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Read/Write Default Register Description HSS Enable (Bit 7) The GPIO Control register configures the GPIO pins for various interface options. It also controls the polarity of the GPIO interrupt on IRQ1 (GPIO25) and IRQ0 (GPIO24). The HSS Enable bit routes HSS to GPIO[26, 18:16]. If the HSS XD Enable bit is set, it overrides this bit and HSS is routed to XD[15:12]. 1: HSS is routed to GPIO 0: HSS is not routed to GPIOs. GPIO[26, 18:16] are free for other purposes Write Protect Enable (Bit 15) The Write Protect Enable bit enables or disables the GPIO write protect. When Write Protect is enabled, the GPIO Mode Select [15:8] field is read only until a chip reset. 1: Enable Write Protect 0: Disable Write Protect UD (Bit 14) The UD bit routes the Host/Device 1A Port’s transmitter enable status to GPIO[30]. This is for use with an external ESD protection circuit when needed. 1: Route the signal to GPIO[30] 0: Do not route the signal to GPIO[30] SAS Enable (Bit 11) The SAS Enable bit, when in SPI mode, reroutes the SPI port SPI_nSSI pin to GPIO[15] rather then GPIO[9] or XD[9] (per SG/SX). 1: Reroute SPI_nss to GPIO[30] 0: Leave SPI_nss on GPIO[9] Mode Select (Bits [10:8]) The Mode Select field selects how GPIO[15:0] and GPIO[24:19] are used as defined in Table 78. Table 78. Mode Select Definition Mode Select GPIO Configuration [10:8] 111 Reserved 110 SCAN — (HW) Scan diagnostic. For production test only. Not for normal operation 101 HPI — Host Port Interface 100 IDE — Integrated Drive Electronics or 011 Reserved 010 Reserved 001 Reserved 000 GPIO — General Purpose Input Output Document #: 38-08015 Rev. *K HSS XD Enable (Bit 6) The HSS XD Enable bit routes HSS to XD[15:12] (external memory data bus). This bit overrides the HSS Enable bit. 1: HSS is routed to XD[15:12] 0: HSS is not routed to XD[15:12] SPI Enable (Bit 5) The SPI Enable bit routes SPI to GPIO[11:8]. If the SAS Enable bit is set, it overrides the SPI Enable and routes SPI_nSSI to GPIO15. If the SPI XD Enable bit is set, it overrides both bits and the SPI is routed to XD[11:8] (external memory data bus). 1: SPI is routed to GPIO[11:8] 0: SPI is not routed to GPIO[11:8]. GPIO[11:8] are free for other purposes SPI XD Enable (Bit 4) The SPI XD Enable bit routes SPI to XD[11:8] (external memory data bus). This bit overrides the SPI Enable bit. 1: SPI is routed to XD[11:8] 0: SPI is not routed to XD[11:8] Interrupt 1 Polarity Select (Bit 3) The Interrupt 1 Polarity Select bit selects the polarity for IRQ1. 1: Sets IRQ1 to rising edge 0: Sets IRQ1 to falling edge Interrupt 1 Enable (Bit 2) The Interrupt 1 Enable bit enables or disables IRQ1. The GPIO bit on the interrupt Enable register must also be set in order for this for this interrupt to be enabled. 1: Enable IRQ1 0: Disable IRQ1 Page 51 of 102 [+] Feedback CY7C67300 Interrupt 0 Polarity Select (Bit 1) Reserved The Interrupt 0 Polarity Select bit selects the polarity for IRQ0. 1: Sets IRQ0 to rising edge 0: Sets IRQ0 to falling edge Write all reserved bits with ’0’. Interrupt 0 Enable (Bit 0) The Interrupt 0 Enable bit enables or disables IRQ0. The GPIO bit on the interrupt Enable register must also be set in order for this for this interrupt to be enabled. 1: Enable IRQ0 0: Disable IRQ0 GPIO n Output Data Register [R/W] ■ GPIO 0 Output Data Register 0xC01E ■ GPIO 1 Output Data Register 0xC024 Table 79. GPIO n Output Data Register Bit # 31/15 30/14 29/13 28/12 Field Read/Write Default Bit # Default 26/10 25/9 24/8 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 23/7 22/6 21/5 20/4 19/3 18/2 17/1 16/0 Field Read/Write 27/11 Data... ...Data R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Register Description Data (Bits [15:0]) The GPIO n Output Data register controls the output data of the GPIO pins. The GPIO 0 Output Data register controls GPIO15 to GPIO0 while the GPIO 1 Output Data register controls GPIO31 to GPIO16. When read, this register reads back the last data written, not the data on pins configured as inputs (see Input Data Register). The Data field[15:0] writes to the corresponding GPIO 15–0 or GPIO31–16 pins as output data. GPIO n Input Data Register [R] ■ GPIO 0 Input Data Register 0xC020 ■ GPIO 1 Input Data Register 0xC026 Table 80. GPIO n Input Data Register Bit # 31/15 30/14 29/13 28/12 Field 27/11 26/10 25/9 24/8 Data... Read/Write R R R R R R R R Default 0 0 0 0 0 0 0 0 23/7 22/6 21//5 20/4 19/3 18/2 17/1 16/0 Bit # Field ...Data Read/Write R R R R R R R R Default 0 0 0 0 0 0 0 0 Register Description Data (Bits [15:0]) The GPIO n Input Data register reads the input data of the GPIO pins. The GPIO 0 Input Data register reads from GPIO15 to GPIO0 while the GPIO 1 Input Data register reads from GPIO31 to GPIO16. The Data field[15:0] contains the voltage values on the corresponding GPIO15–0 or GPIO31–16 input pins. Document #: 38-08015 Rev. *K Page 52 of 102 [+] Feedback CY7C67300 GPIO n Direction Register [R/W] ■ GPIO 0 Direction Register 0xC022 ■ GPIO 1 Direction Register 0xC028 Table 81. GPIO n Direction Register Bit # 31/15 30/14 29/13 28/12 R/W R/W R/W R/W 0 0 0 0 23/7 22/6 21/5 20/4 Field Read/Write Default Bit # Default 26/10 25/9 24/8 R/W R/W R/W R/W 0 0 0 0 19/3 18/2 17/1 16/0 Direction Select... Field Read/Write 27/11 ...Direction Select R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Register Description IDE Registers The GPIO n Direction register controls the direction of the GPIO data pins (input/output). The GPIO 0 Direction register controls GPIO15 to GPIO0 while the GPIO 1 Direction register controls GPIO31 to GPIO16. In addition to the standard IDE PIO Port registers, there are four registers dedicated to IDE operation. These registers are covered in this section and summarized in Table 82. Table 82. IDE Registers Direction Select (Bits [15:0]) Register Name The Direction Select field[15:0] configures the corresponding GPIO15–0 or GPIO31–16 pins as either input or output. When any bit of this register is set to ‘1’, the corresponding GPIO data pin becomes an output. When any bit of this register is set to ‘0’, the corresponding GPIO data pin becomes an input. Address R/W IDE Mode Register 0xC048 R/W IDE Start Address Register 0xC04A R/W IDE Stop Address Register 0xC04C R/W IDE Control Register 0xC04E R/W IDE PIO Port Registers 0xC050-0xC06F R/W IDE Mode Register [0xC048] [R/ W] Table 83. IDE Mode Register Bit # 15 14 13 12 Field 11 10 9 8 Reserved... Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Read/Write - - - - R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Field ...Reserved Mode Select Register Description Mode Select (Bits [2:0]) The IDE Mode register allows the selection of IDE PIO Modes 0, 1, 2, 3, or 4. The default setting is zero which means IDE PIO Mode 0. The Mode Select field sets PIO Mode 0 to 4 in IDE mode. Refer to Table 84 on page 54 for a definition of this field. Document #: 38-08015 Rev. *K Page 53 of 102 [+] Feedback CY7C67300 Table 84. Mode Select Definition Mode Select [2:0] 000 001 010 011 100 101 110 111 Mode IDE PIO Mode 0 IDE PIO Mode 1 IDE PIO Mode 2 IDE PIO Mode 3 IDE PIO Mode 4 Reserved Reserved Disable IDE port operations Reserved Write all reserved bits with ’0’. IDE Start Address Register [0xC04A] [R/W] Table 85. IDE Start Address Register Bit # 15 14 13 12 Field Read/Write 11 10 9 8 Address... R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field Read/Write Default ...Address R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Register Description The IDE Start Address register holds the start address for an IDE block transfer. This register is byte addressed and IDE block transfers are 16-bit words, therefore the LSB of the start address is ignored. Block transfers begin at IDE Start Address and end with the final word at IDE Stop Address. When IDE Start Address equals IDE Stop Address, the block transfer moves one word of data. Document #: 38-08015 Rev. *K The hardware keeps an internal memory address counter. The two MSBs of the addresses are not modified by the address counter. Therefore, the IDE Start Address and IDE Stop Address must reside within the same 16K byte block. Address (Bits [15:0]) The Address field sets the start address for an IDE block transfer. Page 54 of 102 [+] Feedback CY7C67300 IDE Stop Address Register [0xC04C] [R/W] Table 86. IDE Stop Address Register Bit # 15 14 13 12 11 10 9 8 R/W R/W R/W R/W Default 0 0 R/W R/W R/W R/W 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Field Read/Write Address... Field Read/Write Default ...Address The hardware keeps an internal memory address counter. The two MSBs of the addresses are not modified by the address counter. Therefore the IDE Start Address and IDE Stop Address must reside within the same 16K byte block. Register Description The IDE Stop Address register holds the stop address for an IDE block transfer. This register is byte addressed and IDE block transfers are 16-bit words, therefore the LSB of the stop address is ignored. Block transfers begin at IDE Start Address and end with the final word at IDE Stop Address. When IDE Start Address equals IDE Stop Address, the block transfer moves one word of data. Address (Bits [15:0]) The Address field sets the stop address for an IDE block transfer. IDE Control Register [0xC04E] [R/W] Table 87. IDE Control Register Bit # 15 14 13 12 Field 11 10 9 8 Reserved... Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 ...Reserved 3 2 1 0 Direction Select IDE Interrupt Enable Done Flag IDE Enable Field Read/Write - - - - R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Register Description Done Flag (Bit 1) The IDE Control register controls block transfers in IDE mode. The Direction Select bit sets the block mode transfer direction. The Done Flag bit is automatically set to ‘1’ by hardware when a block transfer is complete. The CPU clears this bit by writing a ‘0’ to it. When IDE Interrupt Enable is set this bit generates the signal for the cpuide_intr interrupt. 1: Data is written to the external device 1: Block transfer is complete 0: Data is read from the external device 0: Clears IDE Done Flag IDE Interrupt Enable (Bit 2) IDE Enable (Bit 0) The IDE Interrupt Enable bit enables or disables the block transfer done interrupt. When enabled, the Done Flag is sent to the CPU as cpuide_intr interrupt. When disabled, the cpuide_intr is set LOW. The IDE Enable bit starts a block transfer. It is reset to ‘0’ when the block transfer is complete Direction Select (Bit 3) 1: Enable block transfer done interrupt 0: Disable block transfer done interrupt 1: Start block transfer 0: Block transfer complete Reserved Write all reserved bits with ’0’. Document #: 38-08015 Rev. *K Page 55 of 102 [+] Feedback CY7C67300 IDE PIO Port Registers [0xC050 - 0xC06F] [R/W] All IDE PIO Port registers [0xC050 - 0xC06F] in Table 88 are defined in detail in the Information Technology-AT Attachment -4 with Packet Interface Extension (ATA/ATAPI-4) Specification, T13/1153D Rev 18. The table Address column denotes the CY7C67300 register address for the corresponding ATA/ATAPI register. The IDE_nCS[1:0] field defines the ATA interface CS addressing bits and the IDE_A[2:0] field define the ATA interface address bits. The combination of IDE_nCS and IDE_A are the ATA interface register address. Table 88. IDE PIO Port Registers Address ATA/ATAPI Register IDE_nCS[1:0] IDE_A[2:0] 0xC050 DATA Register ‘10’ ‘000’ 0xC052 Read: Error Register Write: Feature Register ‘10’ ‘001’ 0xC054 Sector Count Register ‘10’ ‘010’ 0xC056 Sector Number Register ‘10’ ‘011’ 0xC058 Cylinder Low Register ‘10’ ‘100’ 0xC05A Cylinder High Register ‘10’ ‘101’ 0xC05C Device/Head Register ‘10’ ‘110’ 0xC05E Read: Status Register Write: Command Register ‘10’ ‘111’ 0xC060 Not Defined ‘01’ ‘000’ 0xC062 Not Defined ‘01’ ‘001’ 0xC064 Not Defined ‘01’ ‘010’ 0xC066 Not Defined ‘01’ ‘011’ 0xC068 Not Defined ‘01’ ‘100’ 0xC06A Not Defined ‘01’ ‘101’ 0xC06C Read: Alternate Status Register Write: Device Control Register ‘01’ ‘110’ 0xC06E Not Defined ‘01’ ‘111’ HSS Registers There are eight registers dedicated to HSS operation. Each of these registers are covered in this section and summarized in Table 89. Table 89. HSS Registers Register Name Address R/W HSS Control Register 0xC070 R/W HSS Baud Rate Register 0xC072 R/W HSS Transmit Gap Register 0xC074 R/W HSS Data Register 0xC076 R/W HSS Receive Address Register 0xC078 R/W HSS Receive Length Register 0xC07A R/W HSS Transmit Address Register 0xC07C R/W HSS Transmit Length Register 0xC07E R/W Document #: 38-08015 Rev. *K Page 56 of 102 [+] Feedback CY7C67300 HSS Control Register [0xC070] [R/W] Table 90. HSS Control Register Bit # 15 14 13 12 11 10 9 8 HSS Enable RTS Polarity Select CTS Polarity Select XOFF XOFF Enable CTS Enable Receive Interrupt Enable Done Interrupt Enable Field Read/Write R/W R/W R/W R R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 One Stop Bit Transmit Ready Packet Mode Select Receive Overflow Flag Receive Packet Ready Flag Receive Ready Flag Field Transmit Receive Done Interrupt Done Interrupt Enable Enable Read/Write R/W R/W R/W R R/W R/W R R 0 0 0 0 0 0 0 0 Default Register Description Receive Interrupt Enable (Bit 9) The HSS Control register provides high level status and control over the HSS port. The Receive Interrupt Enable bit enables or disables the Receive Ready and Receive Packet Ready interrupts. HSS Enable (Bit 15) 1: Enable the Receive Ready and Receive Packet Ready interrupts The HSS Enable bit enables or disables HSS operation. 1: Enables HSS operation 0: Disables HSS operation RTS Polarity Select (Bit 14) 0: Disable the Receive Ready and Receive Packet Ready interrupts Done Interrupt Enable (Bit 8) The RTS Polarity Select bit selects the polarity of RTS. The Done Interrupt Enable bit enables or disables the Transmit Done and Receive Done interrupts. 1: RTS is true when LOW 1: Enable the Transmit Done and Receive Done interrupts 0: RTS is true when HIGH 0: Disable the Transmit Done and Receive Done interrupts CTS Polarity Select (Bit 13) Transmit Done Interrupt Flag (Bit 7) The CTS Polarity Select bit selects the polarity of CTS. 1: CTS is true when LOW The Transmit Done Interrupt Flag bit indicates the status of the Transmit Done Interrupt. It sets when a block transmit is finished. To clear the interrupt, write a ‘1’ to this bit. 0: CTS is true when HIGH 1: Interrupt triggered XOFF (Bit 12) 0: Interrupt did not trigger The XOFF bit is a read only bit that indicates if an XOFF was received. This bit is automatically cleared when an XON is received. Receive Done Interrupt Flag (Bit 6) 1: XOFF received The Receive Done Interrupt Flag bit indicates the status of the Receive Done Interrupt. It sets when a block transmit is finished. To clear the interrupt, write a ‘1’ to this bit. 0: XON received 1: Interrupt triggered XOFF Enable (Bit 11) 0: Interrupt did not trigger The XOFF Enable bit enables or disables XON/XOFF software handshaking. One Stop Bit (Bit 5) 0: Disable XON/XOFF software handshaking The One Stop Bit bit selects between one and two stop bits for transmit byte mode. In receive mode, the number of stop bits may vary and does not need to be fixed. CTS Enable (Bit 10) 1: One stop bit The CTS Enable bit enables or disables CTS/RTS hardware handshaking. 0: Two stop bits 1: Enable XON/XOFF software handshaking 1: Enable CTS/RTS hardware handshaking 0: Disable CTS/RTS hardware handshaking Document #: 38-08015 Rev. *K Page 57 of 102 [+] Feedback CY7C67300 Transmit Ready (Bit 4) 1: Overflow occurred The Transmit Ready bit is a read only bit that indicates if the HSS Transmit FIFO is ready for the CPU to load new data for transmission. 0: Overflow did not occur 1: HSS transmit FIFO ready for loading The Receive Packet Ready Flag bit is a read only bit that indicates if the HSS receive FIFO is full with eight bytes or not. 0: HSS transmit FIFO not ready for loading Receive Packet Ready Flag (Bit 1) 1: HSS receive FIFO is full Packet Mode Select (Bit 3) 0: HSS receive FIFO is not full The Packet Mode Select bit selects between Receive Packet Ready and Receive Ready as the interrupt source for the RxIntr interrupt. Receive Ready Flag (Bit 0) The Receive Ready Flag is a read only bit that indicates if the HSS receive FIFO is empty or not. 1: Selects Receive Packet Ready as the source 0: Selects Receive Ready as the source 1: HSS receive FIFO is not empty (one or more bytes is reading for reading) Receive Overflow Flag (Bit 2) 0: HSS receive FIFO is empty The Receive Overflow Flag bit indicates if the Receive FIFO overflowed when set. This flag can be cleared by writing a ‘1’ to this bit. HSS Baud Rate Register [0xC072] [R/W] Table 91. HSS Baud Rate Register Bit # 15 Field 14 13 12 11 Reserved 10 9 8 Baud... Read/Write - - - R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 1 0 1 1 1 Field Read/Write Default ...Baud Register Description Reserved The HSS Baud Rate register sets the HSS Baud Rate. At reset, the default value is 0x0017 which sets the baud rate to 2.0 MHz. Write all reserved bits with ’0’. Baud (Bits [12:0]) The Baud field is the baud rate divisor minus one, in units of 1/48 MHz. Therefore the Baud Rate = 48 MHz/(Baud + 1). This puts a constraint on the Baud Value as follows: (24 – 1) ≤ Baud ≥ (5000 – 1) Document #: 38-08015 Rev. *K Page 58 of 102 [+] Feedback CY7C67300 HSS Transmit Gap Register [0xC074] [R/W] Table 92. HSS Transmit Gap Register Bit # 15 14 13 12 Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 1 0 0 1 9 8 Field Default 10 9 8 Reserved Field Read/Write 11 Transmit Gap Select Register Description Reserved The HSS Transmit Gap register is only valid in block transmit mode. It allows for a programmable number of stop bits to be inserted, thus overwriting the One Stop Bit in the HSS Control register. The default reset value of this register is 0x0009, equivalent to two stop bits. Write all reserved bits with ’0’. Transmit Gap Select (Bits [7:0]) The Transmit Gap Select field sets the inactive time between transmitted bytes. The inactive time = (Transmit Gap Select –7) * bit time. Therefore a Transmit Gap Select Value of 8 is equal to having one Stop bit. HSS Data Register [0xC076] [R/W] Table 93. HSS Data Register Bit # 15 14 13 12 Field 11 10 Reserved Read/Write - - - - - - - - Default X X X X X X X X Bit # 7 6 5 4 3 2 1 0 Field Read/Write Default Data R/W R/W R/W R/W R/W R/W R/W R/W X X X X X X X X Register Description Data (Bits [7:0]) The HSS Data register contains data received on the HSS port (not for block receive mode) when read. This receive data is valid when the Receive Ready bit of the HSS Control register is set to ‘1’. Writing to this register initiates a single byte transfer of data. The Transmit Ready Flag in the HSS Control register must read ‘1’ before writing to this register (this avoids disrupting the previous/current transmission). The Data field contains the data received or to be transmitted on the HSS port. Document #: 38-08015 Rev. *K Reserved Write all reserved bits with ’0’. Page 59 of 102 [+] Feedback CY7C67300 HSS Receive Address Register [0xC078] [R/W] Table 94. HSS Receive Address Register Bit # 15 14 13 12 11 10 9 8 R/W R/W R/W R/W Default 0 0 R/W R/W R/W R/W 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Field Read/Write Address... Field Read/Write Default ...Address Register Description Address (Bits [15:0]) The HSS Receive Address register is used as the base pointer address for the next HSS block receive transfer. The Address field sets the base pointer address for the next HSS block receive transfer. HSS Receive Counter Register [0xC07A] [R/W] Table 95. HSS Receive Counter Register Bit # 15 14 13 Field 12 11 10 9 Reserved 8 Counter... Read/Write - - - - - - R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field Read/Write Default ...Counter R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Register Description Counter (Bits [9:0]) The HSS Receive Counter register designates the block byte length for the next HSS receive transfer. Load this register with the word count minus one to start the block receive transfer. As each byte is received this register value is decremented. When read, this register indicates the remaining length of the transfer. The Counter field value is equal to the word count minus one giving a maximum value of 0x03FF (1023) or 2048 bytes. When the transfer is complete this register returns 0x03FF until reloaded. Reserved Write all reserved bits with ’0’. Document #: 38-08015 Rev. *K Page 60 of 102 [+] Feedback CY7C67300 HSS Transmit Address Register [0xC07C] [R/W] Table 96. HSS Transmit Address Register Bit # 15 14 13 12 11 10 9 8 R/W R/W R/W R/W Default 0 0 R/W R/W R/W R/W 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Field Read/Write Address... Field Read/Write Default ...Address Register Description Address (Bits [15:0]) The HSS Transmit Address register is used as the base pointer address for the next HSS block transmit transfer. The Address field sets the base pointer address for the next HSS block transmit transfer. HSS Transmit Counter Register [0xC07E] [R/W] Table 97. HSS Transmit Counter Register Bit # 15 14 13 Field 12 11 10 9 Reserved 8 Counter... Read/Write - - - - - - R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field Read/Write Default ...Counter R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Register Description Counter (Bits [9:0]) The HSS Transmit Counter register designates the block byte length for the next HSS transmit transfer. Load this register with the word count minus one to start the block transmit transfer. As each byte is transmitted this register value is decremented. When read, this register indicates the remaining length of the transfer. The Counter field value is equal to the word count minus one giving a maximum value of 0x03FF (1023) or 2048 bytes. When the transfer is complete this register returns 0x03FF until reloaded. Reserved Write all reserved bits with ’0’. Document #: 38-08015 Rev. *K Page 61 of 102 [+] Feedback CY7C67300 HPI Registers Table 98. HPI Registers There are five registers dedicated to HPI operation. In addition, there is an HPI status port which can be addressed over HPI. Each of these registers is covered in this section and are summarized in Table 98. Register Name HPI Breakpoint Register Interrupt Routing Register SIE1msg Register SIE2msg Register HPI Mailbox Register Address 0x0140 0x0142 0x0144 0x0148 0xC0C6 R/W R R W W R/W HPI Breakpoint Register [0x0140] [R] Table 99. HPI Breakpoint Register Bit # 15 14 13 12 Field 11 10 9 8 Address... Read/Write R R R R R R R R Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field ...Address Read/Write R R R R R R R R Default 0 0 0 0 0 0 0 0 When the program counter matches the Breakpoint Address, the INT127 interrupt triggers. To clear this interrupt, write a zero a to this register. Register Description The HPI Breakpoint register is a special on-chip memory location that the external processor can access using normal HPI memory read/write cycles. This register is read only by the CPU but is read/write by the HPI port. The contents of this register have the same effect as the Breakpoint register [0xC014]. This special Breakpoint register is used by software debuggers that interface through the HPI port instead of the serial port. Address (Bits [15:0]) The Address field is a 16-bit field containing the breakpoint address. Interrupt Routing Register [0x0142] [R] Table 100. Interrupt Routing Register Bit # 15 14 Field VBUS to HPI Enable ID to HPI Enable 13 12 11 10 9 SOF/EOP2 to SOF/EOP2 to SOF/EOP1 to SOF/EOP1 to Reset2 to HPI HPI Enable CPU Enable HPI Enable CPU Enable Enable 8 HPI Swap 1 Enable Read/Write - - - - - - - - Default 0 0 0 1 0 1 0 0 5 2 1 Bit # 7 6 Field Resume2 to HPI Enable Resume1 to HPI Enable 4 Reserved 3 Done2 to HPI Enable Done1 to HPI Reset1 to HPI Enable Enable 0 HPI Swap 0 Enable Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Register Description The Interrupt Routing register allows the HPI port to take over some or all of the SIE interrupts that usually go to the on-chip CPU. This register is read only by the CPU but is read/write by the HPI port. By setting the appropriate bit to ‘1’, the SIE interrupt is routed to the HPI port to become the HPI_INTR signal and also readable in the HPI Status register. The bits in this register select where the interrupts are routed. The individual interrupt enable is handled in the SIE interrupt enable register. VBUS to HPI Enable (Bit 15) The VBUS to HPI Enable bit routes the OTG VBUS interrupt to the HPI port instead of the on-chip CPU. 1: Route signal to HPI port 0: Do not route signal to HPI port Document #: 38-08015 Rev. *K Page 62 of 102 [+] Feedback CY7C67300 ID to HPI Enable (Bit 14) Resume2 to HPI Enable (Bit 7) The ID to HPI Enable bit routes the OTG ID interrupt to the HPI port instead of the on-chip CPU. 1: Route signal to HPI port The Resume2 to HPI Enable bit routes the USB Resume interrupt that occurs on Host 2 to the HPI port instead of the on-chip CPU. 0: Do not route signal to HPI port 1: Route signal to HPI port SOF/EOP2 to HPI Enable (Bit 13) The SOF/EOP2 to HPI Enable bit routes the SOF/EOP2 interrupt to the HPI port. 1: Route signal to HPI port 0: Do not route signal to HPI port SOF/EOP2 to CPU Enable (Bit 12) 0: Do not route signal to HPI port Resume1 to HPI Enable (Bit 6) The Resume1 to HPI Enable bit routes the USB Resume interrupt that occurs on Host 1 to the HPI port instead of the on-chip CPU. 1: Route signal to HPI port 0: Do not route signal to HPI port The SOF/EOP2 to CPU Enable bit routes the SOF/EOP2 interrupt to the on-chip CPU. Since the SOF/EOP2 interrupt can be routed to both the on-chip CPU and the HPI port, the firmware must ensure only one of the two (CPU, HPI) resets the interrupt. The Done2 to HPI Enable bit routes the Done interrupt for Host/Device 2 to the HPI port instead of the on-chip CPU. 1: Route signal to CPU 1: Route signal to HPI port 0: Do not route signal to CPU 0: Do not route signal to HPI port Done2 to HPI Enable (Bit 3) SOF/EOP1 to HPI Enable (Bit 11) Done1 to HPI Enable (Bit 2) The SOF/EOP1 to HPI Enable bit routes the SOF/EOP1 interrupt to the HPI port. The Done1 to HPI Enable bit routes the Done interrupt for Host/Device 1 to the HPI port instead of the on-chip CPU. 1: Route signal to HPI port 1: Route signal to HPI port 0: Do not route signal to HPI port 0: Do not route signal to HPI port SOF/EOP1 to CPU Enable (Bit 10) Reset1 to HPI Enable (Bit 1) The SOF/EOP1 to CPU Enable bit routes the SOF/EOP1 interrupt to the on-chip CPU. Since the SOF/EOP1 interrupt can be routed to both the on-chip CPU and the HPI port, the firmware must ensure only one of the two (CPU, HPI) resets the interrupt. The Reset1 to HPI Enable bit routes the USB Reset interrupt that occurs on Device 1 to the HPI port instead of the on-chip CPU. 1: Route signal to CPU 0: Do not route signal to CPU Reset2 to HPI Enable (Bit 9) The Reset2 to HPI Enable bit routes the USB Reset interrupt that occurs on Device 2 to the HPI port instead of the on-chip CPU. 1: Route signal to HPI port 0: Do not route signal to HPI port 1: Route signal to HPI port 0: Do not route signal to HPI port HPI Swap 0 Enable (Bit 0) Both HPI Swap bits (bits 8 and 0) must be set to identical values. When set to ‘00’, the most significant data byte goes to HPI_D[15:8] and the least significant byte goes to HPI_D[7:0]. This is the default setting. By setting to ‘11’, the most significant data byte goes to HPI_D[7:0] and the least significant byte goes to HPI_D[15:8]. HPI Swap 1 Enable (Bit 8) Both HPI Swap bits (bits 8 and 0) must be set to identical values. When set to ‘00’, the most significant data byte goes to HPI_D[15:8] and the least significant byte goes to HPI_D[7:0]. This is the default setting. By setting to ‘11’, the most significant data byte goes to HPI_D[7:0] and the least significant byte goes to HPI_D[15:8]. Document #: 38-08015 Rev. *K Page 63 of 102 [+] Feedback CY7C67300 SIEXmsg Register [W] ■ SIE1msg Register 0x0144 ■ SIE2msg Register 0x0148 Table 101. SIEXmsg Register Bit # 15 14 13 12 11 10 9 8 Read/Write W W W W Default X X W W W W X X X X X X Bit # 7 6 5 4 3 2 1 0 Read/Write W W W W Default W W W W X X X X X X X X Field Data... Field ...Data Register Description Data (Bits [15:0]) The SIEXmsg register allows an interrupt to be generated on the HPI port. Any write to this register causes the SIEXmsg flag in the HPI Status Port to go high and also causes an interrupt on the HPI_INTR pin. The SIEXmsg flag is automatically cleared when the HPI port reads from this register. The Data field[15:0] simply needs to have any value written to it to cause SIExmsg flag in the HPI Status Port to go high. HPI Mailbox Register [0xC0C6] [R/W] Table 102. HPI Mailbox Register Bit # 15 14 13 12 Field Read/Write 11 10 9 8 Message... R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field Read/Write Default ...Message R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Register Description The HPI Mailbox register provides a common mailbox between the CY7C67300 and the external host processor. If enabled, the HPI Mailbox RX Full interrupt triggers when the external host processor writes to this register. When the CY7C67300 reads this register the HPI Mailbox RX Full interrupt is automatically cleared. If enabled, the HPI Mailbox TX Empty interrupt triggers when the external host processor reads from this register. The HPI Mailbox TX Empty interrupt automatically clears when the CY7C67300 writes to this register. Document #: 38-08015 Rev. *K In addition, when the CY7C67300 writes to this register, the HPI_INTR signal on the HPI port asserts, signaling the external processor that there is data in the mailbox to read. The HPI_INTR signal deasserts when the external host processor reads from this register. Message (Bits [15:0]) The Message field contains the message that the host processor wrote to the HPI Mailbox register. Page 64 of 102 [+] Feedback CY7C67300 HPI Status Port [] [HPI: R] Table 103. HPI Status Port Bit # 15 14 13 12 11 10 9 8 VBUS Flag ID Flag Reserved SOF/EOP2 Flag Reserved Field SOF/EOP1 Flag Reset2 Flag Mailbox In Flag Read/Write R R - R - R R R Default X X X X X X X X Bit # 7 6 5 4 3 2 1 0 Resume2 Flag Resume1 Flag SIE2msg SIE1msg Field Done2 Flag Done1 Flag Reset1 Flag Mailbox Out Flag Read/Write R R R R R R R R Default X X X X X X X X Register Description Mailbox In Flag (Bit 8) The HPI Status Port provides the external host processor with the MailBox status bits plus several SIE status bits. This register is not accessible from the on-chip CPU. The additional SIE status bits are provided to aid external device driver firmware development, and are not recommended for applications that do not have an intimate relationship with the on-chip BIOS. The Mailbox In Flag bit is a read only bit that indicates if a message is ready in the incoming mailbox. This interrupt clears when the on-chip CPU reads from the HPI Mailbox register. Reading from the HPI Status Port does not result in a CPU HPI interface memory access cycle. The external host may continuously poll this register without degrading the CPU or DMA performance. Resume2 Flag (Bit 7) VBUS Flag (Bit 15) 0: Interrupt did not trigger The VBUS Flag bit is a read only bit that indicates whether OTG VBus is greater than 4.4V. After turning on VBUS, firmware must wait at least 10 µs before this reading this bit. Resume1 Flag (Bit 6) 1: Interrupt triggered 0: Interrupt did not trigger The Resume2 Flag bit is a read only bit that indicates if a USB resume interrupt occurs on either Host/Device 2. 1: Interrupt triggered 1: OTG VBus is greater than 4.4V The Resume1 Flag bit is a read only bit that indicates if a USB resume interrupt occurs on either Host/Device 1. 0: OTG VBus is less than 4.4V 1: Interrupt triggered ID Flag (Bit 14) The ID Flag bit is a read only bit that indicates the state of the OTG ID pin. SOF/EOP2 Flag (Bit 12) The SOF/EOP2 Flag bit is a read only bit that indicates if a SOF/EOP interrupt occurs on either Host/Device 2. 1: Interrupt triggered 0: Interrupt did not trigger SIE2msg (Bit 5) The SIE2msg Flag bit is a read only bit that indicates if the CY7C67300 CPU wrote to the SIE2msg register. This bit is cleared on an HPI read. 1: The SIE2msg register was written by the CY7C67300 CPU 0: The SIE2msg register was not written by the CY7C67300 CPU 0: Interrupt did not trigger SIE1msg (Bit 4) SOF/EOP1 Flag (Bit 10) The SIE1msg Flag bit is a read only bit that indicates if the CY7C67300 CPU wrote to the SIE1msg register. This bit is cleared on an HPI read. The SOF/EOP1 Flag bit is a read only bit that indicates if a SOF/EOP interrupt occurs on either Host/Device 1. 1: The SIE1msg register was written by the CY7C67300 CPU 1: Interrupt triggered 0: The SIE1msg register was not written by the CY7C67300 CPU 0: Interrupt did not trigger Reset2 Flag (Bit 9) The Reset2 Flag bit is a read only bit that indicates if a USB Reset interrupt occurs on either Host/Device 2. 1: Interrupt triggered 0: Interrupt did not trigger Done2 Flag (Bit 3) In host mode the Done2 Flag bit is a read only bit that indicates if a host packet done interrupt occurs on Host 2. In device mode this read only bit indicates if an any of the endpoint interrupts occur on Device 2. Firmware needs to determine which endpoint interrupt occurred. 1: Interrupt triggered 0: Interrupt did not trigger Document #: 38-08015 Rev. *K Page 65 of 102 [+] Feedback CY7C67300 Done1 Flag (Bit 2) In host mode the Done 1 Flag bit is a read only bit that indicates if a host packet done interrupt occurs on Host 1. In device mode this read only bit indicates if an any of the endpoint interrupts occur on Device 1. Firmware needs to determine which endpoint interrupt occurred. 1: Interrupt triggered The Reset1 Flag bit is a read only bit that indicates if a USB Reset interrupt occurs on either Host/Device 1. 1: Interrupt triggered 0: Interrupt did not trigger Mailbox Out Flag (Bit 0) 0: Interrupt did not trigger The Mailbox Out Flag bit is a read only bit that indicates if a message is ready in the outgoing mailbox. This interrupt clears when the external host reads from the HPI Mailbox register. Reset1 Flag (Bit 1) 1: Interrupt triggered 0: Interrupt did not trigger SPI Registers There are twelve registers dedicated to SPI operation. Each of these registers is covered in this section and summarized in Table 104. Table 104. SPI Registers Register Name SPI Configuration Register SPI Control Register SPI Interrupt Enable Register SPI Status Register SPI Interrupt Clear Register SPI CRC Control Register SPI CRC Value SPI Data Register SPI Transmit Address Register SPI Transmit Count Register SPI Receive Address Register SPI Receive Count Register Document #: 38-08015 Rev. *K Address 0xC0C8 0xC0CA 0xC0CC 0xC0CE 0xC0D0 0xC0D2 0xC0D4 0xC0D6 0xC0D8 0xC0DA 0xC0DC 0xC0DE R/W R/W R/W R/W R W R/W R/W R/W R/W R/W R/W R/W Page 66 of 102 [+] Feedback CY7C67300 SPI Configuration Register [0xC0C8] [R/W] Table 105. SPI Configuration Register Bit # 15 14 13 Field 3Wire Enable Phase Select SCK Polarity Select Read/Write 12 11 10 9 Scale Select 8 Reserved R/W R/W R/W R/W R/W R/W R/W - Default 1 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Master Enable SS Enable Field Master Active Enable Read/Write R R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 1 1 1 1 1 SS Delay Select Table 106. Scale Select Field Definition for SCK Frequency Register Description The SPI Configuration register controls the SPI port. Fields apply to both master and slave mode unless otherwise noted. 3Wire Enable (Bit 15) The 3Wire Enable bit indicates if the MISO and MOSI data lines are tied together allowing only half duplex operation. 1: MISO and MOSI data lines are tied together 0: Normal MISO and MOSI Full Duplex operation (not tied together) Scale Select [12:9] 1001 SCK Frequency 500 KHz 1010 1011 1100 1101 1110 1111 375 KHz 250 KHz 375 KHz 250 KHz 375 KHz 250 KHz Phase Select (Bit 14) The Phase Select bit selects advanced or delayed SCK phase. This field only applies to master mode. 1: Advanced SCK phase 0: Delayed SCK phase SCK Polarity Select (Bit 13) This SCK Polarity Select bit selects the polarity of SCK. 1: Positive SCK polarity 0: Negative SCK polarity Scale Select (Bits [12:9]) The Scale Select field provides control over the SCK frequency, based on 48 MHz. Refer to Table 106 for a definition of this field. This field only applies to master mode. Table 106. Scale Select Field Definition for SCK Frequency Scale Select [12:9] 0000 SCK Frequency 12 MHz 0001 0010 0011 0100 0101 0110 0111 1000 8 MHz 6 MHz 4 MHz 3 MHz 2 MHz 1.5 MHz 1 MHz 750 KHz Document #: 38-08015 Rev. *K Master Active Enable (Bit 7) The Master Active Enable bit is a read only bit that indicates if the master state machine is active or idle. This field only applies to master mode. 1: Master state machine is active 0: Master state machine is idle Master Enable (Bit 6) The Master Enable bit sets the SPI interface to master or slave. This bit is only writable when the Master Active Enable bit reads ‘0’, otherwise the value does not change. 1: Master SPI interface 0: Slave SPI interface SS Enable (Bit 5) The SS Enable bit enables or disables the master SS output. 1: Enable master SS output 0: Disable master SS output (three state master SS output, for single SS line in slave mode) SS Delay Select (Bits [4:0]) When the SS Delay Select field is set to ‘00000’ this indicates manual mode. In manual mode SS is controlled by the SS Manual bit of the SPI Control register. When the SS Delay Select field is set between ‘00001’ to ‘11111’, this value indicates the count in half bit times of auto transfer delay for: SS low to SCK active, SCK inactive to SS high, SS high time. This field only applies to master mode. Page 67 of 102 [+] Feedback CY7C67300 SPI Control Register [0xC0CA] [R/W] Table 107. SPI Control Register Bit # 15 14 13 12 11 10 9 8 SCK Strobe FIFO Init Byte Mode Full Duplex SS Manual Read Enable Transmit Ready Receive Data Ready Read/Write W W R/W R/W R/W R/W R R Default 0 0 0 0 0 0 0 1 Bit # 7 6 5 4 3 2 1 0 Field Transmit Empty Receive Full Read/Write R R R/W R/W R/W R/W R/W R/W Default 1 0 0 0 0 0 0 0 Field Transmit Bit Length Receive Bit Length Register Description Read Enable (Bit 10) The SPI Control register controls the SPI port. Fields apply to both master and slave mode unless otherwise noted. The Read Enable bit initiates a read phase for a master mode transfer or sets the slave to receive (in slave mode). SCK Strobe (Bit 15) 1: Initiates a read phase for a master transfer or sets a slave to receive. In master mode this bit is sticky and remains set until the read transfer begins. The SCK Strobe bit starts the SCK strobe at the selected frequency and polarity (set in the SPI Configuration register), but not phase. This bit feature can only be enabled when in master mode and must be during a period of inactivity. This bit is self clearing. 1: SCK Strobe Enable 0: No Function FIFO Init (Bit 14) The FIFO Init bit initializes the FIFO and clears the FIFO Error Status bit. This bit is self clearing. 1: FIFO Init Enable 0: No Function Byte Mode (Bit 13) The Byte Mode bit selects between PIO (byte mode) and DMA (block mode) operation. 1: Set PIO (byte mode) operation 0: Set DMA (block mode) operation 0: Initiates the write phase for slave operation Transmit Ready (Bit 9) The Transmit Ready bit is a read only bit that indicates if the transmit port is ready to empty and ready to be written. 1: Ready for data to be written to the port. The transmit FIFO is not full. 0: Not ready for data to be written to the port Receive Data Ready (Bit 8) The Receive Data Ready bit is a read only bit that indicates if the receive port has data ready. 1: Receive port has data ready to read 0: Receive port does not have data ready Transmit Empty (Bit 7) The Transmit Empty bit is a read only bit that indicates if the transmit FIFO is empty. 1: Transmit FIFO is empty Full Duplex (Bit 12) 0: Transmit FIFO is not empty The Full Duplex bit selects between full duplex and half duplex operation. Receive Full (Bit 6) 1: Enable full duplex. Full duplex is not allowed and does not set if the 3Wire Enable bit of the SPI Configuration register is set to ‘1’ The Receive Full bit is a read only bit that indicates if the receive FIFO is full. 0: Enable half duplex operation 0: Receive FIFO is not full 1: Receive FIFO is full SS Manual (Bit 11) Transmit Bit Length (Bits [5:3]) The SS Manual bit activates or deactivates SS if the SS Delay Select field of the SPI Control register is all zeros and is configured as master interface. This field only applies to master mode. The Transmit Bit Length field controls whether a full byte or partial byte is to be transmitted. If Transmit Bit Length is ‘000’ then a full byte is transmitted. If Transmit Bit Length is ‘001’ to ‘111’, then the value indicates the number of bits that are be transmitted. 1: Activate SS, master drives SS line asserted LOW 0: Deactivate SS, master drives SS line deasserted HIGH Document #: 38-08015 Rev. *K Page 68 of 102 [+] Feedback CY7C67300 Receive Bit Length (Bits [2:0]) The Receive Bit Length field controls whether a full byte or partial byte is received. If Receive Bit Length is ‘000’ then a full byte is received. If Receive Bit Length is ‘001’ to ‘111’, then the value indicates the number of bits that are received. SPI Interrupt Enable Register [0xC0CC] [R/W] Table 108. SPI Interrupt Enable Register Bit # 15 14 13 12 Field 11 10 9 8 Reserved... Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 ...Reserved Field 2 1 0 Receive Interrupt Enable Transmit Interrupt Enable Transfer Interrupt Enable Read/Write - - - - - R/W R/W R/W Default 0 0 0 0 0 0 0 0 Register Description 1: Enables byte mode transmit interrupt The SPI Interrupt Enable register controls the SPI port. 0: Disables byte mode transmit interrupt Receive Interrupt Enable (Bit 2) Transfer Interrupt Enable (Bit 0) The Receive Interrupt Enable bit enables or disables the byte mode receive interrupt (RxIntVal). The Transfer Interrupt Enable bit enables or disables the block mode interrupt (XfrBlkIntVal). 1: Enable byte mode receive interrupt 1: Enables block mode interrupt 0: Disable byte mode receive interrupt 0: Disables block mode interrupt Transmit Interrupt Enable (Bit 1) Reserved The Transmit Interrupt Enable bit enables or disables the byte mode transmit interrupt (TxIntVal). Write all reserved bits with ’0’. SPI Status Register [0xC0CE] [R] Table 109. SPI Status Register Bit # 15 14 13 12 Field 11 10 9 8 Reserved Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 7 6 5 4 3 Bit # FIFO Error Flag Reserved Field 2 1 0 Receive Interrupt Flag Transmit Interrupt Flag Transfer Interrupt Flag Read/Write R - - - - R R R Default 0 0 0 0 0 0 0 0 Register Description The SPI Status register is a read only register that provides status for the SPI port. FIFO Error Flag (Bit 7) The FIFO Error Flag bit is a read only bit that indicates if a FIFO error occurred. When this bit is set to ‘1’ and the Transmit Empty Document #: 38-08015 Rev. *K bit of the SPI Control register is set to ‘1’, then a Tx FIFO underflow occurred. Similarly, when set with the Receive Full bit of the SPI Control register, an Rx FIFO overflow occured.This bit automatically clears when the SPI FIFO Init Enable bit of the SPI Control register is set. 1: Indicates FIFO error 0: Indicates no FIFO error Page 69 of 102 [+] Feedback CY7C67300 Receive Interrupt Flag (Bit 2) 1: Indicates a byte mode transmit interrupt triggered The Receive Interrupt Flag is a read only bit that indicates if a byte mode receive interrupt triggered. 0: Indicates a byte mode transmit interrupt did not trigger Transfer Interrupt Flag (Bit 0) 1: Indicates a byte mode receive interrupt triggered 0: Indicates a byte mode receive interrupt did not trigger The Transfer Interrupt Flag is a read only bit that indicates a block mode interrupt triggered. Transmit Interrupt Flag (Bit 1) 1: Indicates a block mode interrupt triggered The Transmit Interrupt Flag is a read only bit that indicates a byte mode transmit interrupt triggered. 0: Indicates a block mode interrupt did not trigger SPI Interrupt Clear Register [0xC0D0] [W] Table 110. SPI Interrupt Clear Register Bit # 15 14 13 12 11 Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Transmit Interrupt Clear Transfer Interrupt Clear Field 10 9 8 Reserved Reserved Field Read/Write - - - - - - W W Default 0 0 0 0 0 0 0 0 Register Description Transfer Interrupt Clear (Bit 0) The SPI Interrupt Clear register is a write only register that allows the SPI Transmit and SPI Transfer Interrupts to be cleared. The Transfer Interrupt Clear bit is a write only bit that clears the block mode interrupt. This bit is self clearing. Transmit Interrupt Clear (Bit 1) 1: Clear the block mode interrupt The Transmit Interrupt Clear bit is a write only bit that clears the byte mode transmit interrupt. This bit is self clearing. 0: No function 1: Clear the byte mode transmit interrupt Write all reserved bits with ’0’. Reserved 0: No function SPI CRC Control Register [0xC0D2] [R/W] Table 111. SPI CRC Control Register Bit # 15 14 CRC Mode Field Read/Write 13 12 11 10 9 8 CRC Enable CRC Clear Receive CRC One in CRC Zero in CRC Reserved... R/W R/W R/W R/W R/W R R - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field ...Reserved Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Register Description CRC Mode (Bits [15:14) The SPI CRC Control register provides control over the CRC source and polynomial value. The CRCMode field selects the CRC polynomial as defined in Table 112 on page 71. Document #: 38-08015 Rev. *K Page 70 of 102 [+] Feedback CY7C67300 Receive CRC (Bit 11) Table 112. CRC Mode Definition CRCMode [15:14] The Receive CRC bit determines whether the receive bit stream or the transmit bit stream is used for the CRC data input in full duplex mode. This bit is a don’t care in half duplex mode. CRC Polynomial 00 MMC 16 bit: X^16 + X^12 + X^5 + 1(CCITT Standard) 01 CRC7 7 bit: X^7+ X^3 + 1 10 MST 16 bit: X^16+ X^15 + X^2 + 1 One in CRC (Bit 10) 11 Reserved, 16 bit polynomial 1 The One in CRC bit is a read only bit that indicates if the CRC value is all zeros or not 1: Assigns the receive bit stream 0: Assigns the transmit bit stream CRC Enable (Bit 13) 1: CRC value is not all zeros The CRC Enable bit enables or disables the CRC operation. 0: CRC value is all zeros 1: Enables CRC operation Zero in CRC (Bit 9) 0: Disables CRC operation The Zero in CRC bit is a read only bit that indicates if the CRC value is all ones or not. CRC Clear (Bit 12) 1: CRC value is not all ones The CRC Clear bit clears the CRC with a load of all ones. This bit is self clearing and always reads ‘0’. 0: CRC value is all ones 1: Clear CRC with all ones Reserved 0: No Function Write all reserved bits with ’0’. SPI CRC Value Register [0xC0D4] [R/W] Table 113. SPI CRC Value Register Bit # 15 14 13 12 11 10 9 8 R/W R/W R/W R/W Default 1 1 R/W R/W R/W R/W 1 1 1 1 1 1 Bit # 7 6 5 4 3 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W 1 1 1 1 1 1 1 1 Field Read/Write CRC... Field Read/Write Default ...CRC Register Description CRC (Bits [15:0]) The SPI CRC Value register contains the CRC value. The CRC field contains the SPI CRC. In CRC Mode CRC7, the CRC value is a seven bit value [6:0]. Therefore, bits [15:7] are invalid in CRC7 mode. Document #: 38-08015 Rev. *K Page 71 of 102 [+] Feedback CY7C67300 SPI Data Register [0xC0D6] [R/W] Table 114. SPI Data Register Bit # 15 14 13 12 Read/Write - - - - - - - - Default X X X X X X X X Bit # 7 6 5 4 3 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W X X X X X X X X Field Default 10 9 8 Reserved Field Read/Write 11 Data Register Description Data (Bits [7:0]) The SPI Data register contains data received on the SPI port when read. Reading it empties the eight byte receive FIFO in PIO byte mode. This receive data is valid when the Receive Interrupt Bit of the SPI Status register is set to ‘1’ (RxIntVal triggers) or the Receive Data Ready bit of the SPI Control register is set to ‘1’. Writing to this register in PIO byte mode initiates a transfer of data, the number of bits defined by Transmit Bit Length field in the SPI Control register. The Data field contains data received or to be transmitted on the SPI port. Reserved Write all reserved bits with ’0’. SPI Transmit Address Register [0xC0D8] [R/W] Table 115. SPI Transmit Address Register Bit # 15 14 13 12 Field Read/Write 11 10 9 8 Address... R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field Read/Write Default ...Address R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Register Description Address (Bits [15:0]) The SPI Transmit Address register is used as the base address for the SPI transmit DMA. The Address field sets the base address for the SPI transmit DMA. Document #: 38-08015 Rev. *K Page 72 of 102 [+] Feedback CY7C67300 SPI Transmit Count Register [0xC0DA] [R/W] Table 116. SPI Transmit Count Register Bit # 15 14 12 11 10 Read/Write - - - - - R/W Default 0 R/W R/W 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Field 13 Reserved Default 8 Count... Field Read/Write 9 ...Count Register Description Reserved The SPI Transmit Count register designates the block byte length for the SPI transmit DMA transfer. Write all reserved bits with ’0’. Count (Bits [10:0]) The Count field sets the count for the SPI transmit DMA transfer. SPI Receive Address Register [0xC0DC [R/W] Table 117. SPI Receive Address Register Bit # 15 14 13 12 Field Read/Write 11 10 9 8 Address... R/W R/W R/W R/W R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field Read/Write Default ...Address R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Register Description Address (Bits [15:0]) The SPI Receive Address register is issued as the base address for the SPI Receive DMA. The Address field sets the base address for the SPI receive DMA. SPI Receive Count Register [0xC0DE] [R/W] Table 118. SPI Receive Count Register Bit # 15 14 Field 13 12 11 10 Reserved 9 8 Count... Read/Write - - - - - R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field Read/Write Default ...Count R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Document #: 38-08015 Rev. *K Page 73 of 102 [+] Feedback CY7C67300 Register Description UART Registers The SPI Receive Count register designates the block byte length for the SPI receive DMA transfer. There are three registers dedicated to UART operation. Each of these registers is covered in this section and summarized in Table 119. Count (Bits [10:0]) Table 119. UART Registers The Count field sets the count for the SPI receive DMA transfer. Register Name UART Control Register UART Status Register UART Data Register Reserved Write all reserved bits with ’0’. Address 0xC0E0 R/W R/W R R/W 0xC0E2 0xC0E4 UART Control Register [0xC0E0] [R/W] Table 120. UART Control Register Bit # 15 14 13 12 Field 11 10 9 8 Reserved... Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 Field ...Reserved Scale Select Baud Select 0 UART Enable Read/Write - - - R/W R/W R/W R/W R/W Default 0 0 0 0 0 1 1 1 Register Description Table 121. UART Baud Select Definition The UART Control register enables or disables the UART, allowing GPIO28 (UART_TXD) and GPIO27 (UART_RXD) to be freed up for general use. This register must also be written to set the baud rate, which is based on a 48 MHz clock. Baud Select Baud Rate w/ DIV8 = 0 Baud Rate w/ DIV8 = 1 [3:1] Scale Select (Bit 4) The Scale Select bit acts as a prescaler that divide the baud rate by eight. 000 115.2 KBaud 14.4 KBaud 001 57.6 KBaud 7.2 KBaud 010 38.4 KBaud 4.8 KBaud 011 28.8 KBaud 3.6 KBaud 1: Enable prescaler 100 19.2 KBaud 2.4 KBaud 0: Disable prescaler 101 14.4 KBaud 1.8 KBaud 110 9.6 KBaud 1.2 KBaud 111 7.2 KBaud 0.9 KBaud Baud Select (Bits [3:1]) Refer to Table 121 for a definition of this field. UART Enable (Bit 0) The UART Enable bit enables or disables the UART. 1: Enable UART 0: Disable UART. This allows GPIO28 and GPIO27 to be used for general use. Reserved Write all reserved bits with ’0’. Document #: 38-08015 Rev. *K Page 74 of 102 [+] Feedback CY7C67300 UART Status Register [0xC0E2] [R] Table 122. UART Status Register Bit # 15 14 13 12 Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 Read/Write - - Default 0 0 Field 11 10 9 8 Reserved... 4 3 2 - - - - 0 0 0 0 Field ...Reserved 1 0 Receive Full Transmit Full R R 0 0 Register Description Transmit Full (Bit 0) The UART Status register is a read only register that indicates the status of the UART buffer. The Transmit Full bit indicates whether the transmit buffer is full. It can be programmed to interrupt the CPU as interrupt #4 when the buffer is empty. This can be done though the UART bit of the Interrupt Enable register (0xC00E). This bit is automatically set to ‘1’ after data is written by EZ-Host to the UART Data register (to be transmitted). This bit is automatically cleared to ‘0’ after the data is transmitted. Receive Full (Bit 1) The Receive Full bit indicates whether the receive buffer is full. It can be programmed to interrupt the CPU as interrupt #5 when the buffer is full. This can be done though the UART bit of the Interrupt Enable register (0xC00E). This bit is automatically cleared when data is read from the UART Data register. 1: Transmit buffer full (transmit busy) 0: Transmit buffer is empty and ready for a new byte of data 1: Receive buffer full 0: Receive buffer empty UART Data Register [0xC0E4] [R/W] Table 123. UART Data Register Bit # 15 14 13 12 Field 11 10 9 8 Reserved Read/Write - - - - - - - - Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 Field Read/Write Default Data R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Register Description Data (Bits [7:0]) The UART Data register contains data to be transmitted or received from the UART port. Data written to this register starts a data transmission and also causes the UART Transmit Full Flag of the UART Status register to set. When data received on the UART port is read from this register, the UART Receive Full Flag of the UART Status register is cleared. The Data field is where the UART data to be transmitted or received is located. Document #: 38-08015 Rev. *K Reserved Write all reserved bits with ’0’. Page 75 of 102 [+] Feedback CY7C67300 PWM Registers There are eleven registers dedicated to PWM operation. Each of these registers are covered in this section and summarized in Table 124. Table 124. PWM Registers Register Name Address R/W 0xC0E6 R/W PWM Maximum Count Register 0xC0E8 R/W PWM0 Start Register 0xC0EA R/W PWM0 Stop Register 0xC0EC R/W PWM1 Start Register 0xC0EE R/W PWM1 Stop Register 0xC0F0 R/W PWM2 Start Register 0xC0F2 R/W PWM2 Stop Register 0xC0F4 R/W PWM3 Start Register 0xC0F6 R/W PWM3 Stop Register 0xC0F8 R/W PWM Cycle Count Register 0xC0FA R/W PWM Control Register PWM Control Register [0xC0E6] [R/W] Table 125. PWM Control Register Bit # 15 Field PWM Enable Read/Write 14 13 12 11 10 Reserved 9 8 Prescale Select Mode Select R/W - - - R/W R/W R/W R/W Default 0 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 PWM 2 Polarity Select PWM 1 Polarity Select PWM 0 Polarity Select PWM 3 Enable PWM 2 Enable PWM 1 Enable PWM 0 Enable Field PWM 3 Polarity Select R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Read/Write Default Register Description The PWM Control register provides high level control over all four of the PWM channels. Table 126. Prescaler Select Definition Prescale Select [11:9] Frequency 000 48.00 MHz PWM Enable (Bit 15) 001 24.00 MHz The PWM Enable bit starts and stops PWM operation. 010 06.00 MHz 1: Start operation 011 01.50 MHz 0: Stop operation 100 375 kHz Prescale Select (Bits [11:9]) 101 93.80 kHz The Prescale Select field sets the frequency of all the PWM channels as defined in Table 126. 110 23.40 kHz 111 05.90 kHz Document #: 38-08015 Rev. *K Page 76 of 102 [+] Feedback CY7C67300 Mode Select (Bit 8) PWM 0 Polarity Select (Bit 4) The Mode Select bit selects between continuous PWM cycling and one shot mode. The default is continuous repeat. The PWM 0 Polarity Select bit selects the polarity for PWM 0. 1: Enable One Shot mode. The mode runs the number of counter cycles set in the PWM Cycle Count register and then stops. 0: Sets the polarity to active LOW 0: Enable Continuous mode. Runs in continuous mode and starts over after the PWM cycle count is reached. PWM 3 Enable (Bit 3) The PWM 3 Enable bit enables or disables PWM 3. PWM 3 Polarity Select (Bit 7) 1: Enable PWM 3 The PWM 3 Polarity Select bit selects the polarity for PWM 3. 0: Disable PWM 3 1: Sets the polarity to active HIGH or rising edge pulse PWM 2 Enable (Bit 2) 0: Sets the polarity to active LOW The PWM 2 Enable bit enables or disables PWM 2. PWM 2 Polarity Select (Bit 6) 1: Enable PWM 2 The PWM 2 Polarity Select bit selects the polarity for PWM 2. 0: Disable PWM 2 1: Sets the polarity to active HIGH or rising edge pulse PWM 1 Enable (Bit 1) 0: Sets the polarity to active LOW The PWM 1 Enable bit enables or disables PWM 1. PWM 1 Polarity Select (Bit 5) 1: Enable PWM 1 The PWM 1 Polarity Select bit selects the polarity for PWM 1. 0: Disable PWM 1 1: Sets the polarity to active HIGH or rising edge pulse PWM 0 Enable (Bit 0) 0: Sets the polarity to active LOW The PWM 0 Enable bit enables or disables PWM 0. 1: Sets the polarity to active HIGH or rising edge pulse 1: Enable PWM 0 0: Disable PWM 0 PWM Maximum Count Register [0xC0E8] [R/W] Table 127. PWM Maximum Count Register Bit # 15 14 13 12 11 10 9 Read/Write - - - - - - R/W Default 0 R/W 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Field Reserved Count... Field Read/Write Default 8 ...Count Register Description Count (Bits [9:0]) The PWM Maximum Count register designates the maximum window for each pulse cycle. Each count tick is based on the clock frequency set in the PWM Control register. The Count field sets the maximum cycle time. Reserved Write all reserved bits with ’0’. Document #: 38-08015 Rev. *K Page 77 of 102 [+] Feedback CY7C67300 PWM n Start Register [R/W] ■ PWM 0 Start Register 0xC0EA ■ PWM 1 Start Register 0xC0EE ■ PWM 2 Start Register 0xC0F2 ■ PWM 3 Start Register 0xC0F6 Table 128. PWM n Start Register Bit # 15 14 13 12 11 10 9 Read/Write - - - - - - R/W Default 0 R/W 0 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Field Reserved 8 Address... Field ...Address Read/Write Default Register Description Address (Bits [9:0]) The PWM n Start register designates where in the window defined by the PWM Maximum Count register to start the PWM pulse for a supplied channel. The Address field designates when to start the PWM pulse. If this start value is equal to the Stop Count Value then the output stays at false. Reserved Write all reserved bits with ’0’. PWM n Stop Register [R/W] ■ PWM 0 Stop Register 0xC0EC ■ PWM 1 Stop Register 0xC0F0 ■ PWM 2 Stop Register 0xC0F4 ■ PWM 3 Stop Register 0xC0F8 Table 129. PWM n Stop Register Bit # 15 14 13 12 11 10 9 Read/Write - - - - - - R/W Default 0 0 R/W 0 0 0 0 0 0 Field Bit # Reserved 7 6 5 Address... 4 3 Field Read/Write 8 2 1 0 ...Address R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Default Register Description The PWM n Stop register designates where in the window defined by the PWM Maximum Count register to stop the PWM pulse for a supplied channel. stays at ‘0’. If the PWM Stop value is greater then the PWM Maximum Count value then the output stays at true. Reserved Write all reserved bits with ’0’. Address (Bits [9:0]) The Address field designates when to stop the PWM pulse. If the PWM Start value is equal to the PWM Stop value then the output Document #: 38-08015 Rev. *K Page 78 of 102 [+] Feedback CY7C67300 PWM Cycle Count Register [0xC0FA] [R/W] Table 130. PWM Cycle Count Register Bit # 15 14 13 12 11 10 9 8 R/W R/W R/W R/W Default 0 0 R/W R/W R/W R/W 0 0 0 0 0 0 Bit # 7 6 5 4 3 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 Field Read/Write Count... Field Read/Write Default ...Count Register Description Count (Bits [9:0]) The PWM Cycle Count register designates the number of cycles to run when in one shot mode. One shot mode is enabled by setting the Mode Select bit of the PWM Control register to ‘1’. The Count field designates the number of cycles (plus one) to run when in one shot mode. For example, Cycles = PWM Cycle Count + 1, therefore for two cycles set PWM Cycle Count = 1. Document #: 38-08015 Rev. *K Page 79 of 102 [+] Feedback CY7C67300 Pin Diagram Figure 11. EZ-Host Pin Diagram D7 D6 D5 D4 D3 D2 D1 D0 nRESET Reserved GPIO7/D7 GPIO6/D6 VCC GPIO5/D5 GPIO4/D4 GPIO3/D3 GPIO2/D2 GPIO1/D1 GPIO0/D0 A18 A17 A16 nBEH GND nBEL/A0 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 A1 1 75 GND A2 2 74 D8/MISO A3 3 73 D9/nSSI DM2B 4 72 D10/SCK DP2B 5 71 D11/MOSI AGND 6 70 D12/TXD A4 7 69 D13/RXD A5 8 68 D14/RTS DM2A 9 67 D15/CTS DP2A 10 66 GPIO8/D8/MISO OTGVBUS 11 65 GPIO9/D9/nSSI CSWITCHB 12 64 nWR CSWITCHA 13 63 VCC VSWITCH 14 62 nRD BOOSTGND 15 61 GPIO10/D10/SCK BOOSTVCC 16 60 GPIO11/D11/MOSI A6 17 59 GPIO12/D12 DM1B 18 58 GPIO13/D13 DP1B 19 57 GPIO14/D14 A7 20 56 GPIO15/D15/nSSI AVCC 21 55 GPIO16/A0/TXD/PWM0 DM1A 22 54 GPIO17/A1/RXD/PWM1 DP1A 23 53 GPIO18/A2/RTS/PWM2 A8 24 52 GPIO19/A0/CS0 A9 25 51 GND CY7C67300 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 GPIO20/A1/CS1 GPIO21/nCS GPIO22/nWR/IOW GPIO23/nRD/IOR GPIO24/INT/IORDY/IRQ0 GPIO25/IRQ1 GPIO26/CTS/PWM3 GPIO27/RX GPIO28/TX GPIO29/OTGID GPIO31/SCL GPIO30/SDA A15/CLKSEL VCC nXRAMSEL nXROMSEL nXMEMSEL A14 A13 A12 A11 XTALIN XTALOUT A10 GND Pin Descriptions Table 131. Pin Descriptions Pin 67 Name D15/CTS Type IO 68 D14/RTS IO 69 D13/RXD IO 70 D12/TXD IO Document #: 38-08015 Rev. *K Description D15: External Memory Data Bus CTS: HSS CTS D14: External Memory Data Bus RTS: HSS RTS D13: External Memory Data Bus RXD: HSS RXD (Data is received on this pin) D12: External Memory Data Bus TXD: HSS TXD (Data is transmitted from this pin) Page 80 of 102 [+] Feedback CY7C67300 Table 131. Pin Descriptions (continued) Pin 71 Name D11/MOSI Type IO 72 D10/SCK IO 73 D9/nSSI IO 74 D8/MISO IO 76 77 78 79 80 81 82 83 33 32 31 30 27 25 24 20 17 8 7 3 2 1 99 D7 D6 D5 D4 D3 D2 D1 D0 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 nBEL/A0 IO IO IO IO IO IO IO IO Output Output Output Output Output Output Output Output Output Output Output Output Output Output Output 98 64 62 97 96 95 34 35 36 38 nBEH nWR nRD A16 A17 A18 nXMEMSEL nXROMSEL nXRAMSEL A15/CLKSEL Output Output Output Output Output Output Output Output Output IO 39 GPIO31/SCK IO 40 GPIO30/SDA IO Document #: 38-08015 Rev. *K Description D11: External Memory Data Bus MOSI: SPI MOSI D10: External Memory Data Bus SCK: SPI SCK D9: External Memory Data Bus nSSI: SPI nSSI D8: External Memory Data Bus MISO: SPI MISO External Memory Data Bus External Memory Address Bus nBEL: Low Byte Enable for 16-bit memories A0: External Memory Address bit A0 for 0-8 bit memories High Byte Enable for 16-bit memories External Memory Write pulse External Memory Read pulse A16: External SRAM A16 A17: External SRAM A17 A18: External SRAM A18 External Memory Select 0 External Memory Select 1 External Memory Select 2 A15: External SRAM A15 CLKSEL: Sampled directly after reset to determine what crystal or clock source frequency is being used. 12 MHz is required for normal operation so the CLKSEL pin must have a 47K ohm pull up to VCC. After reset this pin functions as A15. GPIO31: General Purpose IO SCK: I2C EEPROM SCK GPIO30: General Purpose IO SDA: I2C EEPROM SDA Page 81 of 102 [+] Feedback CY7C67300 Table 131. Pin Descriptions (continued) Pin 41 Name GPIO29/OTGID Type IO 42 GPIO28/TX IO 43 GPIO27/RX IO 44 GPIO26/CTS/PWM3 IO 45 GPIO25/IRQ1 IO 46 GPIO24/INT/ IORDY/IRQ0 IO 47 GPIO23/nRD/IOR IO 48 GPIO22/nWR/IOW IO 49 GPIO21/nCS IO 50 GPIO20/A1/CS1 IO 52 GPIO19/A0/CS0 IO 53 GPIO18/A2/RTS/ PWM2 IO 54 GPIO17/A1/RXD/ PWM1 IO 55 GPIO16/A0/TXD/ PWM0 IO 56 GPIO15/D15/nSSI IO 57 GPIO14/D14 IO 58 GPIO13/D13 IO 59 GPIO12/D12 IO Document #: 38-08015 Rev. *K Description GPIO29: General Purpose IO OTGID: Input for OTG ID pin. When used as OTGID, tie this pin high through an external pull up resistor. Assuming VCC = 3.0V, a 10K to 40K resistor must be used. GPIO28: General Purpose IO TX: UART TX (Data is transmitted from this pin) GPIO27: General Purpose IO RX: UART RX (Data is received on this pin) GPIO26: General Purpose IO CTS: HSS CTS PWM3: PWM channel 3 GPIO25: General Purpose IO IRQ1: Interrupt Request 1. See Register 0xC006. This pin is also one of two possible GPIO wakeup sources. GPIO24: General Purpose IO INT: HPI INT IORDY: IDE IORDY IRQ0: Interrupt Request 0. See Register 0xC006. This pin is also one of two possible GPIO wakeup sources. GPIO23: General Purpose IO nRD: HPI nRD IOR: IDE IOR GPIO22: General Purpose IO nWR: HPI nWR IOW: IDE IOW GPIO21: General Purpose IO nCS: HPI nCS GPIO20: General Purpose IO A1: HPI A1 CS1: IDE CS1 GPIO19: General Purpose IO A0: HPI A0 CS0: IDE CS0 GPIO18: General Purpose IO A2: IDE A2 RTS: HSS RTS PWM2: PWM channel 2 GPIO17: General Purpose IO A1: IDE A1 RXD: HSS RXD (Data is received on this pin) PWM1: PWM channel 1 GPIO16: General Purpose IO A0: IDE A0 TXD: HSS TXD (Data is transmitted from this pin) PWM0: PWM channel 0 GPIO15: General Purpose IO D15: D15 for HPI or IDE nSSI: SPI nSSI GPIO14: General Purpose IO D14: D14 for HPI or IDE GPIO13: General Purpose IO D13: D13 for HPI or IDE GPIO12: General Purpose IO D12: D12 for HPI or IDE Page 82 of 102 [+] Feedback CY7C67300 Table 131. Pin Descriptions (continued) Pin 60 Name GPIO11/D11/MOSI Type IO 61 GPIO10/D10/SCK IO 65 GPIO9/D9/nSSI IO 66 GPIO8/D8/MISO IO 86 GPIO7/D7 IO 87 GPIO6/D6 IO 89 GPIO5/D5 IO 90 GPIO4/D4 IO 91 GPIO3/D3 IO 92 GPIO2/D2 IO 93 GPIO1/D1 IO 94 GPIO0/D0 IO 22 23 18 19 9 10 4 5 29 28 85 84 16 14 DM1A DP1A DM1B DP1B DM2A DP2A DM2B DP2B XTALIN XTALOUT nRESET Reserved BOOSTVCC VSWITCH 15 11 13 12 21 6 37, 63, 88 26, 51, 75, 100 BOOSTGND OTGVBUS CSWITCHA CSWITCHB AVCC AGND VCC GND IO IO IO IO IO IO IO IO Input Output Input Power Analog Output Ground Analog IO Analog Analog Power Ground Power Ground Document #: 38-08015 Rev. *K Description GPIO11: General Purpose IO D11: D11 for HPI or IDE MOSI: SPI MOSI GPIO10: General Purpose IO D10: D10 for HPI or IDE SCK: SPI SCK GPIO9: General Purpose IO D9: D9 for HPI or IDE nSSI: SPI nSSI GPIO8: General Purpose IO D8: D8 for HPI or IDE MISO: SPI MISO GPIO7: General Purpose IO D7: D7 for HPI or IDE GPIO6: General Purpose IO D6: D6 for HPI or IDE GPIO5: General Purpose IO D5: D5 for HPI or IDE GPIO4: General Purpose IO D4: D4 for HPI or IDE GPIO3: General Purpose IO D3: D3 for HPI or IDE GPIO2: General Purpose IO D2: D2 for HPI or IDE GPIO1: General Purpose IO D1: D1 for HPI or IDE GPIO0: General Purpose IO D0: D0 for HPI or IDE USB Port 1A D– USB Port 1A D+ USB Port 1B D– USB Port 1B D+ USB Port 2A D– USB Port 2A D+ USB Port 2B D– USB Port 2B D+ Crystal input or Direct Clock input Crystal output. Leave floating if direct clock source is used. Reset Tie to Gnd for normal operation. Booster Power input: 2.7V to 3.6V Booster switching output Booster Ground USB OTG Vbus Charge Pump Capacitor Charge Pump Capacitor USB Power USB Ground Main VCC Main Ground Page 83 of 102 [+] Feedback CY7C67300 Absolute Maximum Ratings This section lists the absolute maximum ratings. Stresses above those listed can cause permanent damage to the device. Exposure to maximum rated conditions for extended periods can affect device operation and reliability. Operating Conditions Storage Temperature .................................. –40°C to +125°C Supply Voltage (BoostVCC)[7] .........................+2.7V to +3.6V Ambient Temperature with Power Supplied.. –40°C to +85°C Supply Voltage to Ground Potential..................0.0V to +3.6V DC Input Voltage to Any General Purpose Input Pin..... 5.5V TA (Ambient Temperature Under Bias) ......... –40°C to +85°C Supply Voltage (VCC, AVCC) ...........................+3.0V to +3.6V Ground Voltage.................................................................. 0V FOSC (Oscillator or Crystal Frequency).... 12 MHz ± 500 ppm ................................................................... Parallel Resonant DC Voltage Applied to XTALIN ............. –0.5V to VCC + 0.5V Static Discharge Voltage.......................................... > 2000V Max Output Current, per IO .......................................... 4 mA Crystal Requirements (XTALIN, XTALOUT) Table 132. Crystal Requirements Crystal Requirements (XTALIN, XTALOUT) Min Typical Parallel Resonant Frequency Max Unit 12 MHz Frequency Stability –500 +500 PPM Load Capacitance 20 33 pF Driver Level 500 µW Startup Time 5 ms Mode of Vibration: Fundamental DC Characteristics Table 133. DC Characteristics [8] Parameter Description Conditions Min Typ. Max Unit 3.0 3.3 3.6 V VCC, AVCC Supply Voltage BoosVCC Supply Voltage 2.7 3.6 V VIH Input HIGH Voltage 2.0 5.5 V VIL Input LOW Voltage 0.8 V II Input Leakage Current 0< VIN < VCC –10.0 +10.0 μA VOH Output Voltage HIGH IOUT = 4 mA 2.4 VOL Output LOW Voltage IOUT = –4 mA 0.4 V IOH Output Current HIGH 10 20 mA IOL Output Current LOW 10 20 mA CIN Input Pin Capacitance Except D+/D– 10 pF D+/D– 15 pF V VHYS Hysteresis on nReset Pin ICC[9, 10] Supply Current 4 transceivers powered 80 100 mA ICCB[9, 10] Supply Current with Booster Enabled 4 transceivers powered 135 180 mA 250 mV Notes 7. The on-chip voltage booster circuit boosts BoostVCC to provide a nominal 3.3V VCC supply. 8. All tests were conducted with Charge pump off. Document #: 38-08015 Rev. *K Page 84 of 102 [+] Feedback CY7C67300 Table 133. DC Characteristics (continued)[8] Parameter ISLEEP Description Sleep Current Conditions Min USB Peripheral: includes 1.5K internal pull up Without 1.5K internal pull up ISLEEPB Sleep Current with Booster Enabled USB Peripheral: includes 1.5K internal pull up Without 1.5K internal pull up Typ. Max Unit 210 500 μA 5 30 μA 190 500 μA 5 30 μA Typ. Max Unit 5.25 V Table 134. DC Characteristics: Charge Pump Parameter Description Conditions VA_VBUS_OUT Regulated OTGVBUS Voltage 8 mA< ILOAD < 10 mA ILOAD = 10 mA TA_VBUS_RISE VBUS Rise Time IA_VBUS_OUT Maximum Load Current Min 4.4 8 CDRD_VBUS OUTVBUS Bypass Capacitance 4.4V< VBUS < 5.25V VA_VBUS_LKG OTGVBUS Leakage Voltage OTGVBUS not driven VDRD_DATA_LKG Dataline Leakage Voltage ICHARGE Charge Pump Current Draw 1.0 100 ms 10 mA 6.5 pF 200 mV 342 mV ILOAD = 8 mA 20 20 mA ILOAD = 0 mA 0 1 mA ILOAD = 8 mA 30 45 mA ILOAD = 0 mA 0 5 mA 8 mA ICHARGEB Charge Pump Current Draw with Booster Active IB_DSCHG_IN B-Device (SRP Capable) Discharge 0V< VBUS < 5.25V Current VA_VBUS_VALID A-Device VBUS Valid 4.4 VA_SESS_VALID A-Device Session Valid 0.8 2.0 VB_SESS_VALID B-Device Session Valid 0.8 4.0 V VA_SESS_END B-Device Session End 0.2 0.8 V E Efficiency When Loaded RPD Data Line Pull Down RA_BUS_IN A-device VBUS Input Impedance to GND RB_SRP_UP B-device VBUS SRP Pull Up RB_SRP_DWN B-device VBUS SRP Pull Down ILOAD = 8 mA, VCC = 3.3V V 75 V % 14.25 24.8 Ω VBUS is not being driven 40 100 kΩ Pull up voltage = 3.0V 281 Ω 656 Ω USB Transceiver USB 2.0 certified in full- and low-speed modes. Notes 9. ICC and ICCB values are the same regardless of USB host or peripheral configuration. 10. There is no appreciable difference in ICC and ICCB values when only two transceivers are powered. Document #: 38-08015 Rev. *K Page 85 of 102 [+] Feedback CY7C67300 AC Timing Characteristics Reset Timing tRESET nRESET tIOACT nRD or nWRL or nWRH Reset Timing Table 135. Reset Timing Parameters Parameter Description Min Typical Max Unit tRESET nRESET Pulse Width 16 clocks[11] tIOACT nRESET HIGH to nRD or nWRx active 200 µs Clock Timing tCLK tLOW XTALIN tFALL tHIGH tRISE Clock Timing Table 136. Clock Timing Parameters Parameter Description fCLK Clock Frequency vXINH[12] Clock Input High (XTALOUT left floating) Min Max 12.0 Unit MHz 1.5 3.0 3.6 V 83.17 83.33 83.5 ns 44 ns tCLK Clock Period tHIGH Clock High Time 36 tLOW Clock Low Time 36 tRISE Clock Rise Time tFALL Clock Fall Time Duty Cycle Typical 45 44 ns 5.0 ns 5.0 ns 55 % Notes 11. Clock is 12 MHz nominal. 12. vXINH is required to be 3.0 V to obtain an internal 50/50 duty cycle clock. Document #: 38-08015 Rev. *K Page 86 of 102 [+] Feedback CY7C67300 SRAM Read Cycle[15] Address CS t AR tCR t RPW RD t CDH t RDH t AC Din Data Valid Table 137. SRAM Read Cycle Parameters Parameter Description Min Typical Max Unit tCR CS LOW to RD LOW 1 ns tRDH RD HIGH to Data Hold 0 ns tCDH CS HIGH to Data Hold 0 ns tRPW[13] RD LOW Time 38 tAR tAC [14] 45 ns RD LOW to Address Valid 0 ns RAM Access to Data Valid 12 ns Notes 13. 0 wait state cycle. 14. tAC External SRAM access time = 12 ns for zero and one wait states. The External SRAM access time = 12 ns + (n – 1)*T for wait states = n, n > 1, T = 48 MHz clock period. 15. Read timing is applicable for nXMEMSEL, nXRAMSEL, and nXROMSEL. Document #: 38-08015 Rev. *K Page 87 of 102 [+] Feedback CY7C67300 SRAM Write Cycle [17] Address t AW tCSW CS tWC t WPW WE t DW Dout t DH Data Valid Table 138. SRAM Write Cycle Parameters Parameter Description Min Typical Max Unit tAW Write Address Valid to WE LOW 7 ns tCSW CS LOW to WE LOW 7 ns tDW Data Valid to WE HIGH 15 ns tWPW[16] WE Pulse Width 15 ns tDH Data Hold from WE HIGH 4.5 ns tWC WE HIGH to CS HIGH 13 ns Notes 16. tWPW The write pulse width = 18.8 ns min. for zero and one wait states. The write pulse = 18.8 ns + (n – 1)*T for wait states = n, n > 1, T = 48 MHz clock period. 17. Write timing is applicable for nXMEMSEL, nXRAMSEL and nXROMSEL. Document #: 38-08015 Rev. *K Page 88 of 102 [+] Feedback CY7C67300 I2C EEPROM Timing-Serial IO tHIGH tLOW tR tF SCL tSU.STA tHD.STA tSU.DAT tHD.DAT tSU.STO tBUF SDA IN tAA tDH SDA OUT Table 139. I2C EEPROM Timing Parameters Parameter Description Min Typical Max Unit 400 kHz fSCL Clock Frequency tLOW Clock Pulse Width Low 1300 ns tHIGH Clock Pulse Width High 600 ns tAA Clock Low to Data Out Valid 900 ns tBUF Bus Idle Before New Transmission 1300 ns tHD.STA Start Hold Time 600 ns tSU.STA Start Setup Time 600 ns tHD.DAT Data In Hold Time 0 ns tSU.DAT Data In Setup Time 100 ns tR Input Rise Time 300 ns tF Input Fall Time 300 ns tSU.STO Stop Setup Time tDH Data Out Hold Time Document #: 38-08015 Rev. *K 600 ns 0 ns Page 89 of 102 [+] Feedback CY7C67300 HPI (Host Port Interface) Write Cycle Timing tCYC tASU tWP tAH ADDR [1:0] tCSH tCSSU nCS nWR nRD Dout [15:0] tDSU tWDH Table 140. HPI Write Cycle Timing Parameters Parameter Description Min Typical Max Unit tASU Address Setup –1 ns tAH Address Hold –1 ns tCSSU Chip Select Setup –1 ns tCSH Chip Select Hold –1 ns tDSU Data Setup 6 ns tWDH Write Data Hold 2 ns tWP Write Pulse Width 2 T[18] tCYC Write Cycle Time 6 T[18] Notes 18. T = system clock period = 1/48 MHz. Document #: 38-08015 Rev. *K Page 90 of 102 [+] Feedback CY7C67300 HPI (Host Port Interface) Read Cycle Timing tCYC tASU tRP tAH ADDR [1:0] tCSH tCSSU nCS tRDH nWR nRD Din [15:0] tACC tRDH Table 141. HPI Read Cycle Timing Parameters Parameter Description Min Typical Max Unit tASU Address Setup –1 ns tAH Address Hold –1 ns tCSSU Chip Select Setup –1 ns tCSH Chip Select Hold –1 ns tACC Data Access Time, from HPI_nRD falling tRDH Read Data Hold, relative to the earlier of HPI_nRD rising or HPI_nCS rising tRP Read Pulse Width 2 T[18] tCYC Read Cycle Time 6 T[18] Document #: 38-08015 Rev. *K 1.5 1 T[18] 7 ns Page 91 of 102 [+] Feedback CY7C67300 IDE Timing The IDE interface supports PIO mode 0-4 as specified in the Information Technology-AT Attachment–4 with Packet Interface Extension (ATA/ATAPI-4) Specification, T13/1153D Rev 18. HSS BYTE Mode Transmit qt_clk CPU may start another BYTE transmit right after TxRdy goes high CPU_A[2:0] CPUHSS_cs CPU_wr BT BT TxRdy flag HSS_TxD start bit Byte transmit triggered by a CPU write to the HSS_TxData register bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 start of last data bit to TxRdy high: 0 min, 4 T max. (T is qt_clk period) TxRdy low to start bit delay: 0 min, BT max when starting from IDEL. For back to back transmit, new START Bit begins immediately following previous STOP bit. (BT = bit period) stop bit start bit programmable 1 or 2 stop bits. 1 stop bit shown. qt_clk, CPU_A, CPUHSS_cs, CPU_wr are internal signals, included in the diagram to illustrate the relationship between CPU operations and HSS port operations. Bit 0 is LSB of data byte. Data bits are HIGH true: HSS_TxD HIGH = data bit value ‘1’. BT = bit time = 1/baud rate. HSS Block Mode Transmit BT HSS_TxD t GAP BLOCK mode transmit timing is similar to BYTE mode, except the STOP bit time is controlled by the HSS_GAP value. The BLOCK mode STOP bit time, tGAP = (HSS_GAP – 9) BT, where BT is the bit time, and HSS_GAP is the content of the HSS Transmit Gap register [0xC074]. The default tGAP is 2 BT. BT = bit time = 1/baud rate. HSS BYTE and BLOCK Mode Receive BT +/- 5% received byte added to receive FIFO during the final data bit time BT +/- 5% HSS_RxD start bit bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 stop bit start bit 10 BT +/- 5% Receive data arrives asynchronously relative to the internal clock. Incoming data bit rate may deviate from the programmed baud rate clock by as much as ±5% (with HSS_RATE value of 23 or higher). BYTE mode received bytes are buffered in a FIFO. The FIFO not empty condition becomes the RxRdy flag. BLOCK mode received bytes are written directly to the memory system. Bit 0 is LSB of data byte. Data bits are HIGH true: HSS_RxD HIGH = data bit value ‘1’. BT = bit time = 1/baud rate. Document #: 38-08015 Rev. *K Page 92 of 102 [+] Feedback CY7C67300 Hardware CTS/RTS Handshake tCTShold tCTShold tCTSsetup tCTSsetup HSS_RTS HSS_CTS HSS_TxD Start of transmission not delayed by HSS_CTS Start of transmission delayed until HSS_CTS goes high tCTSsetup: HSS_CTS setup time before HSS_RTS = 1.5T min. tCTShold: HSS_CTS hold time after START bit = 0 ns min. T = 1/48 MHz. When RTS/CTS hardware handshake is enabled, transmission can be help off by deasserting HSS_CTS at least 1.5T before HSS_RTS. Transmission resumes when HSS_CTS returns HIGH. HSS_CTS must remain HIGH until START bit. HSS_RTS is deasserted in the third data bit time. An application may choose to hold HSS_CTS until HSS_RTS is deasserted, which always occurs after the START bit. Register Summary Table 142. Register Summary R/W R Address Register 0x0140 HPI Breakpoint Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Default High Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Default Low Address... 0000 0000 ...Address R W R/W 0x0142 Interrupt Routing 1: 0x0144 SIEXmsg 2: 0x0148 0x02n0 Device n Endpoint n Control 0000 0000 VBUS to HPI ID to HPI Enable Enable SOF/EOP2 to SOF/EOP2 to SOF/EOP1 to SOF/EOP1 to Reset2 to HPI HPI Swap 1 HPI Enable CPU Enable HPI Enable CPU Enable Enable Enable 0001 0100 Resume2 to HPI Enable Reserved 0000 0000 Resume1 to HPI Enable Data... xxxx xxxx ...Data xxxx xxxx Reserved xxxx xxxx IN/OUT Sequence Ignore Enable Select R/W 0x02n2 Device n Endpoint n Address Done2 to HPI Done1 to HPI Reset1 to HPI HPI Swap 0 Enable Enable Enable Enable Stall Enable ISO Enable NAK Interrupt Direction Enable Select Enable ARM Enable Address... xxxx xxxx xxxx xxxx ...Address xxxx xxxx R.W 0x02n4 Device n Endpoint n Count Reserved Count... xxxx xxxx R/W 0x02n6 Device n Endpoint n Status Reserved R/W 0x02n8 Device n Endpoint n Count Result Result... xxxx xxxx ...Result xxxx xxxx ...Count Stall Flag R 0xC000 CPU Flags xxxx xxxx NAK Flag Length Setup Exception Flag Flag 0xC002 Bank 0xC004 Hardware Revision OUT IN xxxx xxxx Exception Flag Exception Flag Sequence Status Timeout Flag Error Flag ACK Flag Negative Flag Overflow Flag Carry Flag Zero Flag Address... R/W 0xC006 0xC008 GPIO Control CPU Speed 000x xxxx Revision... xxxx xxxx xxxx xxxx Write Protect Enable UD Reserved HSS Enable HSS XD Enable SPI Enable SPI XD Enable 0xC00A Power Control Mode Select Interrupt 1 Polarity Select Interrupt 1 Enable 0000 0000 Interrupt 0 Polarity Select Interrupt 0 Enable Host/Device 2B Wake Enable 0000 0000 0000 0000 CPU Speed Host/Device 2A Wake Enable HPI Reserved Wake Enable Document #: 38-08015 Rev. *K SAS Enable Reserved... .Reserved R/W 000x xxxx 0000 0001 Reserved ...Revision R/W xxxx xxxx 0000 0000 Global Interrupt Enable ...Address R Underflow Flag Reserved... ...Reserved R/W Overflow Flag Host/Device 1B Wake Enable Host/Device 1A Wake Enable OTG Wake Enable GPI Reserved Wake Enable 0000 1111 Reserved HSS Wake Enable SPI Wake Enable 0000 0000 Boost 3V OK Sleep Enable Halt Enable 0000 0000 Page 93 of 102 [+] Feedback CY7C67300 Table 142. Register Summary (continued) R/W R/W Address Register 0xC00C Watchdog Timer Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Default High Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Default Low Timeout Flag Period Select Lock Enable WDT Enable Reset Strobe 0000 0000 Reserved... 0000 0000 ...Reserved R/W 0xC00E Interrupt Enable Reserved HSS Interrupt Enable R/W 0xC098 OTG Control Reserved D+ Pulldown Enable R/W R/W R/W R/W R R/W R/W In Mailbox Interrupt Enable OTG Interrupt SPI Interrupt Reserved Enable Enable Host/Device 2 Host/Device 1 0000 0000 Interrupt Interrupt Enable Enable Out Mailbox Interrupt Enable Reserved UART Interrupt Enable Timer 1 Interrupt Enable Timer 0 Interrupt Enable 0001 0000 VBUS Pull-up Enable Receive Disable Charge Pump VBUS Enable Discharge Enable D+ Pull-up Enable D– Pull-up Enable 0000 0000 ID Status VBUS Valid Flag 0000 0xxx D– Pull-down Reserved Enable OTG Data Status 0: 0xC010 Timer n 1: 0xC012 Count... 1111 1111 ...Count 1111 1111 0xC014 Address... 0000 0000 ...Address 0000 0000 1: 0xC018 Extended Page n Map 2: 0xC01A Address... 0000 0000 ...Address 0000 0000 0: 0xC01E GPIO n Output Data 1: 0xC024 Data... 0000 0000 ...Data 0000 0000 0: 0xC020 GPIO n Input Data 1: 0xC026 Data... 0000 0000 ...Data 0000 0000 0: 0xC022 GPIO n Direction 1: 0xC028 Direction Select... 0000 0000 ...Direction Select 0000 0000 0xC038 Reserved Breakpoint Upper Address Enable xxxx xxxx Reserved R/W R/W W GPIO Interrupt Enable 0xC03A 0xC03C 0xC03E External Memory Control USB Diagnostic Memory Diagnostic Upper Address Enable Reserved Reserved xxxx 0xxx XRAM XROM XMEM XMEM Merge Enable Merge Enable Width Select Wait Select xxxx xxxx XRAM XRAM Width Select Wait Select xxxx xxxx 0000 0000 XROM Width Select XROM Wait Select Port 2B Diagnostic Enable Port 2A Diagnostic Enable Port 1B Diagnostic Enable Port 1A Diagnostic Enable Reserved... ...Reserved Pull-down Enable LS Pull-up Enable FS Pull-up Enable Reserved Reserved Force Select 0000 0000 Memory Arbitration Select 0000 0000 Reserved R/W 0xC048 IDE Mode Monitor Enable Reserved... 0000 0000 0000 0000 ...Reserved Reserved Mode Select 0000 0000 R/W 0xC04A IDE Start Address Address... 0000 0000 ... Address 0000 0000 R/W 0xC04C IDE Stop Address Address... 0000 0000 ...Address 0000 0000 R/W 0xC04E IDE Control Reserved... 0000 0000 ...Reserved - 0xC050-0 IDE PIO Port xC06E R/W 0xC070 HSS Control R/W 0xC072 HSS Baud Rate R/W R/W R/W 0xC074 0xC076 0xC078 HSS Transmit Gap HSS Data HSS Receive Address Direction Select IDE Interrupt Enable Done Flag IDE Enable 0000 0000 XOFF XOFF Enable CTS Enable Receive Interrupt Enable Done Interrupt Enable 0000 0000 Transmit Done Receive Done One Interrupt Flag Interrupt Flag Stop Bit Transmit Ready Packet Mode Receive Receive Pack- Receive Select Overflow Flag et Ready Flag Ready Flag Reserved HSS Baud... HSS Enable RTS Polarity Select CTS Polarity Select 0000 0000 ...Baud 0001 0111 Reserved 0000 0000 Transmit Gap Select 0000 1001 Reserved xxxx xxxx Data xxxx xxxx Address... 0000 0000 ...Address R/W R/W 0xC07A 0xC07C HSS Receive Counter HSS Transmit Address Document #: 38-08015 Rev. *K 0000 0000 Reserved 0000 0000 Counter... 0000 0000 ...Counter 0000 0000 Address.. 0000 0000 ...Address 0000 0000 Page 94 of 102 [+] Feedback CY7C67300 Table 142. Register Summary (continued) R/W R/W Address Register 0xC07E HSS Transmit Counter Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Default High Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Default Low Reserved Counter... 0000 0000 ...Counter R/W R/W R/W R/W R 0xC080 0xC0A0 Host n Control 0xC082 0xC0A2 Host n Address 0xC084 0xC0A4 Host n Count 0xC084 0xC0A4 Device n Port Select 0xC086 0xC0A6 Host n PID Reserved Preamble Enable R 0xC088 0xC0A8 Host n Count Result W 0xC088 0xC0A8 Host n Device Address 0xC08A 0xC0AA USB n Control 0xC08C R/W R/W 0xC08C Reserved Reserved 0000 0000 Port Select Reserved Count... 0000 0000 Reserved 0000 0000 Port Select Reserved... 0000 0000 0000 0000 Reserved NAK Flag Length Reserved Exception Flag Host 1 Interrupt Enable Device 1 Interrupt Enable Device n Address 0xC090 Host 1 Status Overflow Flag Underflow Flag Reserved Sequence Status Timeout Flag Error Flag 0000 0000 0000 0000 Endpoint Select 0000 0000 Result... 0000 0000 ...Result 0000 0000 Reserved... 0000 0000 ...Reserved Address Port B D+ Status Port B D– Status Port A Resistors Enable Port B Force D+/State VBUS Interrupt Enable ID Interrupt Enable 0000 0000 Port A D+ Status Port A D– Status LOB Port A Force D± State LOA Mode Select Port B Resistors Enable xxxx 0000 Suspend Enable Port B SOF/EOP Enable Port A SOF/EOP Enable 0000 0000 SOF/EOP Interrupt Enable Reserved 0000 0000 Done Interrupt Enable 0000 0000 Reserved VBUS Interrupt Enable ID Interrupt Enable Reserved EP7 Interrupt Enable EP6 Interrupt Enable EP5 Interrupt Enable Port A Connect Change Interrupt Enable EP4 Interrupt Enable Reserved SOF/EOP Timeout Interrupt Enable Reserved SOF/EOP Interrupt Enable Reset Interrupt Enable 0000 0000 EP3 Interrupt Enable EP2 Interrupt Enable EP1 Interrupt Enable EP0 Interrupt Enable 0000 0000 Reserved... ...Reserved Device 1 Status 0000 0000 ACK Flag Reserved PID Select 0xC08E 0xC0AE 0xC090 0000 0000 0000 0000 0000 0000 Address 0000 0000 VBUS ID Reserved Interrupt Flag Interrupt Flag Port B Port A Port B Connect Port A ConPort B Wake Interrupt Wake Interrupt Change nect Change SE0 Flag Flag Interrupt Flag Interrupt Flag Status R/W Arm Enable Address... Port B Port A Port B Connect Wake Interrupt Wake Interrupt Change Enable Enable Interrupt Enable R/W ISO Enable ...Reserved Host n EP Status R/W Sync Enable ...Count 0xC086 0xC0A4 R/W 0000 0000 Sequence Select ...Address Stall Flag W 0000 0000 Port A SE0 Status VBUS ID Reserved Interrupt Flag Interrupt Flag SOF/EOP Reserved Interrupt Flag xxxx xxxx Reserved xxxx xxxx Done Interrupt Flag SOF/EOP Reset xxxx xxxx Interrupt Flag Interrupt Flag EP7 EP6 EP5 EP4 EP3 EP2 EP1 EP0 xxxx xxxx Interrupt Flag Interrupt Flag Interrupt Flag Interrupt Flag Interrupt Flag Interrupt Flag Interrupt Flag Interrupt Flag R/W 0xC092 0xC0B2 Host n SOF/EOP Count Reserved R 0xC092 0xC0B2 Device n Frame Number SOF/EOP Timeout Flag R 0xC094 0xC0B4 Host n SOF/EOP Counter Reserved 0xC094 0xC0B4 Device n SOF/EOP Count 0xC096 0xC0B6 Host n Frame 0xC0AC Host 2 Interrupt Enable Count... 0010 1110 ...Count 1110 0000 SOF/EOP Timeout Interrupt Count Reserved Frame... 0000 0000 ...Frame W R R/W 0000 0000 Counter... xxxx xxxx ...Counter Reserved xxxx xxxx Count... 0010 1110 ...Count 1110 0000 Reserved Frame... 0000 0000 ...Frame Reserved Port B Port A Port B Connect Wake Interrupt Wake Interrupt Change Enable Enable Interrupt Enable Document #: 38-08015 Rev. *K 0000 0000 SOF/EOP Interrupt Enable Port A Connect Change Interrupt Enable Reserved Reserved 0000 0000 Done Interrupt Enable 0000 0000 Page 95 of 102 [+] Feedback CY7C67300 Table 142. Register Summary (continued) R/W R/W Address Register 0xC0AC Device 2 Interrupt Enable Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Default High Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Default Low SOF/EOP Timeout Interrupt Enable Wake Interrupt Enable SOF/EOP Interrupt Enable Reset Interrupt Enable 0000 0000 EP3 Interrupt Enable EP2 Interrupt Enable EP1 Interrupt Enable EP0 Interrupt Enable 0000 0000 SOF/EOP Interrupt Flag Reserved xxxx xxxx Port A SE0 Status Reserved Done Interrupt Flag xxxx xxxx Wake Interrupt Flag SOF/EOP Interrupt Flag Reset Interrupt Flag xxxx xxxx Reserved EP7 Interrupt Enable R/W 0xC0B0 Host 2 Status EP6 Interrupt Enable EP5 Interrupt Enable Reserved Port B Port A Port B Wake Interrupt Wake Interrupt Connect Flag Flag Change Interrupt Flag R/W 0xC0B0 Device 2 Status EP4 Interrupt Enable Port A Port B Connect SE0 Change Status Interrupt Flag Reserved SOF/EOP Timeout Interrupt Enable EP7 EP6 EP5 EP4 EP3 EP2 EP1 EP0 xxxx xxxx Interrupt Flag Interrupt Flag Interrupt Flag Interrupt Flag Interrupt Flag Interrupt Flag Interrupt Flag Interrupt Flag R/W 0xC0C6 HPI Mailbox Message... 0000 0000 ...Message R/W R/W R/W R 0xC0C8 0xC0CA 0xC0CC 0xC0CE SPI Configuration SPI Control SPI Interrupt Enable SPI Status 3Wire Enable 0xC0D0 SPI Interrupt Clear SCK Scale Select Polarity Select Reserved Master Master Active Enable Enable SS Enable SS Delay Select SCK Strobe FIFO Init Byte Mode FullDuplex Transmit Empty Receive Full Transmit Bit Length SS Manual 1000 0000 0001 1111 Read Enable Transmit Ready receive Data Ready Receive Bit Length 0000 0001 1000 0000 Reserved... 0000 0000 ...Reserved Receive Inter- Transmit Inter- Transfer Inter- 0000 0000 rupt Enable rupt Enable rupt Enable Reserved... FIFO Error Flag W 0000 0000 Phase Select 0000 0000 Reserved Receive Transmit Transfer 0000 0000 Interrupt Flag Interrupt Flag Interrupt Flag Reserved... 0000 0000 ...Reserved Transmit Transmit 0000 0000 Interrupt Clear Interrupt Clear R/W 0xC0D2 SPI CRC Control CRC Mode ...Reserved 0000 0000 R/W 0xC0D4 SPI CRC Value CRC 1111 1111 ...CRC 1111 1111 Reserved xxxx xxxx Data xxxx xxxx Address... 0000 0000 R/W R/W 0xC0D6 0xC0D8 SPI Data Port t SPI Transmit Address CRC Enable CRC Clear Receive CRC One in CRC Zero in CRC Reserved... ...Address R/W R/W 0xC0DA 0xC0DC SPI Transmit Count SPI Receive Address 0000 0000 Reserved Count... 0000 0000 ...Count 0000 0000 Address... 0000 0000 ...Address R/W 0xC0DE SPI Receive Count 0000 0000 Reserved Count... 0000 0000 ...Count R/W 0xC0E0 UART Control 0000 0000 Reserved... 0000 0000 ...Reserved R 0xC0E2 UART Status Scale Select Baud Select UART Enable 0000 0111 Reserved... 0000 0000 ...Reserved R/W 0xC0E4 UART Data Receive Full Transmit Full Reserved 0xC0E6 PWM Control PWM Enable 0000 0000 Reserved Prescale Select PWM3 PWM2 PWM1 PWM0 PWM3 Polarity Select Polarity Select Polarity Select Polarity Select Enable R/W 0xC0E8 PWM Maximum Count Reserved PWM2 Enable PWM1 Enable Count... ...Count R/W 0: PWM n Start 0xC0EA 1: 0xC0EE 2: 0xC0F2 3: 0xC0F6 Document #: 38-08015 Rev. *K Reserved ...Address 0000 0000 0000 0000 Data R/W 0000 0000 Mode Select 0000 0000 PWM0 Enable 0000 0000 0000 0000 0000 0000 Address... 0000 0000 0000 0000 Page 96 of 102 [+] Feedback CY7C67300 Table 142. Register Summary (continued) R/W R/W R/W Address Register 0: PWM n Stop 0xC0EC 1: 0xC0F0 2: 0xC0F4 3: 0xC0F8 0xC0FA PWM Cycle Count Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Default High Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Default Low Reserved Address... 0000 0000 ...Address 0000 0000 Count... 0000 0000 ...Count R HPI Status Port VBUS Flag 0000 0000 ID Flag Reserved Resume2 Flag Resume1 Flag SIE2msg Document #: 38-08015 Rev. *K SOF/EOP2 Flag Reserved SOF/EOP1 Flag Reset2 Flag Mailbox In Flag SIE1msg Done2 Flag Done1 Flag Reset1 Flag Mailbox Out Flag Page 97 of 102 [+] Feedback CY7C67300 Ordering Information Table 143. Ordering Information Ordering Code Package Type CY7C67300-100AXI AEC Pb-Free Temperature Range X –40 to 85°C 100-pin TQFP CY7C67300-100AXA 100-pin TQFP CY7C67300-100AXIT 100-pin TQFP, tape and reel X CY7C67300-100AXAT 100-pin TQFP, tape and reel CY3663 Development kit CY4640 Mass storage reference design X –40 to 85°C X –40 to 85°C X X –40 to 85°C X X –40 to 85°C Ordering Code Definitions CY 67300 - xxx AX (I, A, E) T Tape and reel Temperature range: I = Industrial; A = Automotive; E= Extended TQFP Pb-free Pin count Part identifier Company Code: CY = Cypress Document #: 38-08015 Rev. *K Page 98 of 102 [+] Feedback CY7C67300 Package Diagram Figure 12. 100-Pin Thin Plastic Quad Flat Pack (TQFP) A100SA 51-85048 *E Document #: 38-08015 Rev. *K Page 99 of 102 [+] Feedback CY7C67300 Acronyms Document Conventions Table 144. Acronyms Used in this Document Units of Measure Acronym Description Table 145. Units of Measure AC alternating current AEC Automotive Electronics Council ns nanosecond CPU central processing unit V volt CRC cyclic redundancy check mV millivolt DC direct current µW microwatt DMA direct memory access µA microampere EEPROM electronically erasable programmable read only memory mA milliampere EOP end of packet µs microsecond XRAM external ram memory ms millisecond FIFO first in first out MHz megahertz GPIO general purpose input/output µF microfarad HSS high speed serial pF picofarad HPI host port interface mW milliwatt IDE integrated device electronics W watt I2C inter-integrated circuit ppm parts per million KVM keyboard-video-mouse °C degree Celsius OTG on-the-go protocol PLL phase locked loop POR power-on reset PIO programmed input/output PWM pulse width modulation RAM random access memory ROM read only memory SPI serial peripheral interface SIE serial-interface-engine SE0 single ended zero SOF start of frame SRAM static random access memory TQFP thin quad flat pack TTL transistor-transistor logic UART universal asynchronous receiver/transmitter USB universal serial bus WDT watchdog timer Document #: 38-08015 Rev. *K Symbol Unit of Measure Page 100 of 102 [+] Feedback CY7C67300 Document History Page Document Title: CY7C67300 EZ-Host™ Programmable Embedded USB Host and Peripheral Controller with Automotive AEC Grade Support Document Number: 38-08015 Revision ECN Orig. of Change Submission Date ** 111872 MUL 03/22/02 Description of Change New Data Sheet *A 116989 MUL 08/23/02 Preliminary Data Sheet *B 125262 MUL 04/10/03 Added Memory Map Section and Ordering Information Section Moved Functional Register Map Tables into Register section General Clean-up *C 126210 MUL 05/23/03 Added Interface Description Section and Power Savings and Reset Section Added Char Data General Clean-up *D 127335 KKV 05/29/03 Corrected font to enable correct symbol display *E 129395 MUL 10/01/03 Final Data Sheet Changed Memory Map Section and added CLKSEL to Pin Description Added USB OTG Logo General Clean-up *F 443992 VCS See ECN Title changed indicating AEC Grade Added information for AEC qualified including part number Fixed misc. errors including: Table 4-1: UART does not have alternate location Section 4.3.4 had incorrect register address Table 4-10 had incorrect pin definitions Section 4.16.2 changed GPIO[31:20] to GPIO[31:30] Corrected Table 7-6 and 7-14 *G 566465 KKVTMP See ECN Added the lead free information on the Ordering Information Section. Implemented the new template with no numbers on the headings. *H 1063560 ARI See ECN Changed Ordering Information table to reflect Automotive Qualification and to meet the MPN Part Number changes reflected in ECN 884880. Changed the EZ-Host Pin Diagram figure to reflect the pin changes. Edited. *I 2514867 PYRS See ECN To publish in Web *J 2544823 BHA/AESA 07/28/08 Updated template. Corrected A18 and A17 pin assignments in Tables 6 and 131. *K 3302644 NMMA 07/05/11 Added CY4640 Reference Design entry in Ordering Information Table. Included table of contents. Added ordering code definitions, acronyms, and units of measure. Updated package diagram from *C to *E Document #: 38-08015 Rev. *K Page 101 of 102 [+] Feedback CY7C67300 Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Automotive Clocks & Buffers Interface Lighting & Power Control PSoC Solutions cypress.com/go/automotive cypress.com/go/clocks psoc.cypress.com/solutions cypress.com/go/interface PSoC 1 | PSoC 3 | PSoC 5 cypress.com/go/powerpsoc cypress.com/go/plc Memory Optical & Image Sensing PSoC Touch Sensing USB Controllers Wireless/RF cypress.com/go/memory cypress.com/go/image cypress.com/go/psoc cypress.com/go/touch cypress.com/go/USB cypress.com/go/wireless © Cypress Semiconductor Corporation, 2002-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document #: 38-08015 Rev. *K Revised July 5, 2011 Page 102 of 102 All products and company names mentioned in this document may be the trademarks of their respective holders. [+] Feedback