MMD MVLP2 Mil-std-883 level b Datasheet

MVLP, MVLL & MVLV Series VCXO
 MIL-STD-883 Level B
Screening Available
 Available to -55°C to + 125°
C Operating
 RoHS Compliant
 Less than 1 pSec Jitter
LVDS
Frequency Range
Frequency Stability*
Operating Temp.Range
Storage Temp. Range
Aging
Logic “0”
Logic “1”
Supply Voltage (Vdd)
Supply Current
LVPECL
70.000MHz to 800.000MHZ
(See Part Number Guide for Options)
(See Part Number Guide for Options)
-55°C to +125°C
±5 ppm / yr max
Vdd – 1.620 VDC max
Vdd- 1.025 vdc min
50 mA max
PECL
+2.5VDC ± 5%
1.43V typ
1.10V typ
50 mA max
+3.3VDC ± 5%
60 mA max
60 mA max
N/A
+5.0VDC ± 5%
N/A
N/A
140 mA max
Symmetry (50% of waveform)
Rise / Fall Time (20% to 80%)
Load
Start Time
Phase Jitter (12kHz to 20MHz)
Vdd – 1.620 VDC max
Vdd- 1.025 vdc min
N/A
(See Part Number Guide for Options)
2nSec max
50 Ohms into Vdd-2.00 VDC
10mSec max
Less than 1 pSec
Vih = 70% of Vdd min to Enable Output
Vil = 30% max or grounded to Disable Output (High Impedance)
Tri-State Operation
* Inclusive of Temp., Load, Voltage and Aging
+2.5VDC
+3.3VDC
+5.0VDC
Control Voltage (Vc)
1.25VDC ±1.00VDC
1.65VDC ±1.50VDC
N/A
Pullability
Linearity
Environmental & Mechanical Detail
Shock
MIL-STD-883, Method 2002 Cond B
Solderability
MIL-STD-883, Method 2003
Solvent Resistance
MIL-STD-202, Method 215
Vibration
MIL-STD-883, Method 2007, Cond A
Gross Leak
Test
MIL-STD-883, Method 1014, Cond C
Fine Leak Test
MIL-STD-883, Method 1014, Cond A2
MSL
Level 1 per IPC/JEDEC J-STD 20
1.25VDC ±1.00VDC
1.65VDC ±1.50VDC
N/A
(See Part Number Guide for Options)
(See Part Number Guide for Options)
N/A
N/A
2.50VDC ±2.00VDC
Marking Detail
Line 1 = MXXXXX
M
=
MMD
XXXXX
=
Frequency in MHZ
S
=
Internal Code
YYWW
=
L
=
Line 2 = SYYWWL
4 Numerical Digit Date Code
(Year / Week) Jan 27 2011=1105
Denotes RoHS Compliant
Line 3 = XXXXX
Internal use only
May vary with lots
Black dot to denote Pin 1
MMD Monitor/Quartztek
30400 Esperanza, Rancho Santa Margarita, CA, 92688
Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com
[email protected]
Revision:
Revisions only with customer approval
10/29/10 D
Pg 1 of 2
Part Number Guide
Frequency
MVL
Output
P = PECL
L = LVPECL
V = LVDS
Supply Voltage
2 = +2.5 VDC
3 = +3.3 VDC
5 = +5.0 VDC
Frequency
Stability
020 = ±20 ppm
025 = ±25 ppm
050 = ±50 ppm
100 = ±100 ppm
Operating
Temperature
Blank = 0°C to +70°C
27 = -20°C to +70°C
48 = -40°C to +85°C
55 = -55°C to +125°C
Symmetry *
Blank = 40%/60%
A = 45%/55%
B = 47.5%/52.5%
Pullability
A = ±200 ppm min
C = ±100 ppm min
D = ±50 ppm min
P = ±25 ppm min
Linearity
Blank = ±20% max
X = ±5% max
Y = ±10% max
Z = ±15% max
*Option B (47.5/52.5%) Available up to 500MHZ only
Please Consult with MMD Sales Deparment for any other Parameters or Options
Mechanical Details
9.80 [.386]
M AX
4.70 [.185]
M AX
MXXXXX
SYYWWL
XXXXX
0.84 [.033]
14.00 [.551]
M AX
7.87 [.310]
5.08 [.200]
2.54 [.100]
3
4
2
5
1
6
5.08 [.200]
1.02 [.040]
2.54 [.100]
2.50 [.098]
D EN O T ES P IN 1
D im ension in Brackets are in Inches
External B ypass Capacitor is Recom m ended
PIN
PIN
PIN
PIN
PIN
PIN
1
2
3
4
5
6
PIN CO N NE CTIO N S
V O LTA G E C O N T R O L
EN ABLE/DISABLE
G R O U ND
O U TPU T
CO M P. O U TPU T
SUPPLY VO LTAG E
R ecom m ended
Land Pattern
Tape & Reel Dimensions
PITCH
Tape Width
REEL DIA
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
PITCH
TAPE WIDTH
REEL DIA
QTY PER REEL
PIN 1 ORIENT.
4.00 [.157]
12.00 [.471]
180 [7.0]
500
Q1
NOTES: UNLESS OTHERWISE SPECIFIED
1. Applicable Standards / Specifications
ANSI Y14.5M, Dimensions and Tolerances
EIA-481-B, 8 mm through 200mm Embossed Carrier Taping and 8 mm and 12 mm
Punched Carrier Taping of Surface Mount Components for Automatic Handling.
2. Dimensions are in millimeters [inch].
3. Tolerances are ±0.1 [.004] mm unless otherwise specified.
4. Do not scale drawing.
DIRECTION OF FEED
MMD Monitor/Quartztek
30400 Esperanza, Rancho Santa Margarita, CA, 92688
Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com
[email protected]
Revision:
Revisions only with customer approval
10/29/10 D
Pg 2 of 2
Similar pages