CEL MC-7847 870 mhz catv 25 db power doubler amplifier Datasheet

DATA SHEET
GaAs MULTI-CHIP MODULE
MC-7847
870 MHz CATV 25 dB POWER DOUBLER AMPLIFIER
DESCRIPTION
The MC-7847 is a GaAs Multi-chip Module designed for use in CATV applications up to 870 MHz. This unit has
low distortion, low noise figure and return loss across the entire frequency band.
Reliability and performance uniformity are assured by our stringent quality and control procedures.
FEATURES
• Low distortion
• High linear gain
GL = 25.0 dB MIN. @f = 870 MHz
• Low return loss
<R>
ORDERING INFORMATION
Part Number
MC-7847
Order Number
Package
MC-7847-AZ
7-pin special with heatsink
Supplying Form
25 pcs MAX./Tray
(Pb-Free)
Remark To order evaluation samples, contact your nearby sales office.
Part number for sample order: MC-7847
ABSOLUTE MAXIMUM RATINGS (TA = +25°C)
Parameter
Symbol
Ratings
Unit
VDD
30
V
Vi
65.0
dBmV
Operating Case Temperature
TC
−30 to +100
°C
Storage Temperature
Tstg
−40 to +100
°C
Supply Voltage
Input Voltage
Note
Note In case of single tone
Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge.
Document No. PG10140EJ02V0DS (2nd edition)
Date Published December 2006 NS CP(N)
The mark <R> shows major revised points.
The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field.
2001, 2006
MC-7847
RECOMMENDED OPERATING CONDITIONS (ZS = ZL = 75 Ω)
Parameter
Supply Voltage
Input Voltage
Symbol
Test Conditions
MIN.
TYP.
MAX.
Unit
23.5
24.0
24.5
V
−
29.0
32.0
dBmV
−30
+25
+85
°C
MIN.
TYP.
MAX.
Unit
f = 870 MHz
25.0
−
26.0
dB
f = 40 to 870 MHz
1.0
1.4
1.8
dB
f = 40 to 870 MHz, Peak to valley
−
−
0.6
dB
VDD
Vi
110 channel,
10 dB tilted across the band
Operating Case Temperature
TC
ELECTRICAL CHARACTERISTICS (TC = 30 ± 5°C, VDD = 24 V, ZS = ZL = 75 Ω)
Parameter
Symbol
Linear Gain
GL
Gain Slope
GSlope
Test Conditions
Gain Flatness
GFlatness
Noise Figure 1
NF1
f = 50 MHz
−
−
5.5
dB
Noise Figure 2
NF2
f = 870 MHz
−
−
6.0
dB
275
−
375
mA
Operating Current
IDD
RF OFF
Composite Triple Beat
CTB
110 channel,
−
−
−60
dBc
Cross Modulation
XM
VO = 50 dBmV at 745.25 MHz,
−
−
−55
dBc
10 dB tilted across the band
−
−
−63
dBc
Composite 2nd Order Beat
CSO
Input Return Loss 1
RLi1
f = 40 to 160 MHz
20
−
−
dB
Input Return Loss 2
RLi2
f = 160 to 320 MHz
20
−
−
dB
Input Return Loss 3
RLi3
f = 320 to 640 MHz
19
−
−
dB
Input Return Loss 4
RLi4
f = 640 to 870 MHz
17
−
−
dB
Output Return Loss 1
RLo1
f = 40 to 160 MHz
20
−
−
dB
Output Return Loss 2
RLo2
f = 160 to 320 MHz
20
−
−
dB
Output Return Loss 3
RLo3
f = 320 to 640 MHz
19
−
−
dB
Output Return Loss 4
RLo4
f = 640 to 870 MHz
18
−
−
dB
2
Data Sheet PG10140EJ02V0DS
MC-7847
PACKAGE DIMENSIONS
7-PIN SPECIAL WITH HEATSINK (UNIT: mm)
8.1 MAX.
38.1±0.25
+0.25
φ 4.25–0.35
27.5 MAX.
4.0±0.25
14.85 MAX.
3.2 MAX.
45.08 MAX.
19.05±0.38
25.4±0.25
6-32UNC2B
0.51±0.05
10.75±0.25
7 8 9
2.62±0.35
5
12.9 MAX.
1 2 3
21.5 MAX.
4.19±0.13
2.54±0.25
A
2.54±0.38
6.3
0.51±0.05
2.5
0.38.. A
±0.05
PIN CONNECTION
VDD
5
1
9
IN
OUT
2
3
7
8
GND
Data Sheet PG10140EJ02V0DS
3
MC-7847
NOTE ON CORRECT USE
(1)
The space between PC board and root of the lead should be kept more than 1 mm to prevent undesired
stress to the lead and also should be kept less than 4 mm to prevent undesired parasitic inductance.
Recommended that space is 2.0 to 3.0 mm typical.
(2)
Recommended torque strength of the screw is 59 to 78 Ncm.
(3)
Form the ground pattern as wide as possible to minimize ground impedance.
(to prevent undesired oscillation)
All the ground pins must be connected together with wide ground pattern to decrease impedance difference.
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered in the following recommended conditions. Other soldering methods and conditions
than the recommended conditions are to be consulted with our sales representatives.
Soldering Method
Pin Part Heating
Soldering Conditions
Pin area temperature : less than 350°C
Condition Symbol
Note
Hour : Within 3 sec./pin
Note The point of pin part heating must be kept more than 1.2 mm distance from the root of lead.
4
Data Sheet PG10140EJ02V0DS
−
MC-7847
• The information in this document is current as of December, 2006. The information is subject to
change without notice. For actual design-in, refer to the latest publications of NEC Electronics data
sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not
all products and/or types are available in every country. Please check with an NEC Electronics sales
representative for availability and additional information.
• No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may
appear in this document.
• NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual
property rights of third parties by or arising from the use of NEC Electronics products listed in this document
or any other liability arising from the use of such products. No license, express, implied or otherwise, is
granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others.
• Descriptions of circuits, software and other related information in this document are provided for illustrative
purposes in semiconductor product operation and application examples. The incorporation of these
circuits, software and information in the design of a customer's equipment shall be done under the full
responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by
customers or third parties arising from the use of these circuits, software and information.
• While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products,
customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To
minimize risks of damage to property or injury (including death) to persons arising from defects in NEC
Electronics products, customers must incorporate sufficient safety measures in their design, such as
redundancy, fire-containment and anti-failure features.
• NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and
"Specific".
The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC
Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of
each NEC Electronics product before using it in a particular application.
"Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio
and visual equipment, home electronic appliances, machine tools, personal electronic equipment
and industrial robots.
"Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed
for life support).
"Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life
support systems and medical equipment for life support, etc.
The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC
Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications
not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to
determine NEC Electronics' willingness to support a given application.
(Note)
(1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its
majority-owned subsidiaries.
(2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as
defined above).
M8E 02. 11-1
Data Sheet PG10140EJ02V0DS
5
MC-7847
Caution
GaAs Products
This product uses gallium arsenide (GaAs).
GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe
the following points.
• Follow related laws and ordinances when disposing of the product. If there are no applicable laws
and/or ordinances, dispose of the product as recommended below.
1. Commission a disposal company able to (with a license to) collect, transport and dispose of
materials that contain arsenic and other such industrial waste materials.
2. Exclude the product from general industrial waste and household garbage, and ensure that the
product is controlled (as industrial waste subject to special control) up until final disposal.
• Do not burn, destroy, cut, crush, or chemically dissolve the product.
• Do not lick the product or in any way allow it to enter the mouth.
4590 Patrick Henry Drive
Santa Clara, CA 95054-1817
Telephone: (408) 919-2500
Facsimile: (408) 988-0279
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant
with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous
Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive
2003/11/EC Restriction on Penta and Octa BDE.
CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates
that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are
exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals.
All devices with these suffixes meet the requirements of the RoHS directive.
This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that
go into its products as of the date of disclosure of this information.
Restricted Substance
per RoHS
Concentration Limit per RoHS
(values are not yet fixed)
Concentration contained
in CEL devices
-A
Not Detected
Lead (Pb)
< 1000 PPM
Mercury
< 1000 PPM
Not Detected
Cadmium
< 100 PPM
Not Detected
Hexavalent Chromium
< 1000 PPM
Not Detected
PBB
< 1000 PPM
Not Detected
PBDE
< 1000 PPM
Not Detected
-AZ
(*)
If you should have any additional questions regarding our devices and compliance to environmental
standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance
content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information
provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better
integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate
information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL
suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for
release.
In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to
customer on an annual basis.
See CEL Terms and Conditions for additional clarification of warranties and liability.
Similar pages