Cree® 5-mm Round LED Model # LC503TBL1-30Q-A1 Data Sheet 30-degree, 5-mm round LED lamp in blue color with water-transparent lens and no stopper Applications • • • • Advertising Signs Indicators Traffic Lights Moving-Message Signs Absolute Maximum Ratings (TA = 25°C) Items Symbol Absolute Maximum Rating Unit IF 25 mA IFP 100 mA Reverse Voltage VR 5 V Power Dissipation PD 100 mW Operation Temperature Topr -40 ~ +95 °C Storage Temperature Tstg -40 ~ +100 °C Lead Soldering Temperature Tsol Forward Current Peak Forward Current Note Max. 260°C for 3 sec. max. (3 mm from the base of the epoxy bulb) Note: Pulse width ≤0.1 msec, duty ≤1/10. D-CT063.000 Data Sheet: CL Typical Electrical & Optical Characteristics (TA = 25°C) Characteristics Symbol Condition Unit Forward Voltage Forward Voltage VF IF = 20 mA V VF IF = 1.0 µA V Reverse Current IR VR = 5 V μA Dominant Wavelength λD IF = 20 mA nm 465 470 Luminous Intensity IV IF = 20 mA mcd 1520 2100 2θ½H-H IF = 20 mA deg 50% Power Angle Minimum Subject to change without notice. www.cree.com/ledlamps Typical Maximum 3.4 4.0 1.7 2.5 100 475 30 Standard Bins for LC503TBL1-30Q-A1 (IF = 20 mA) Lamps are sorted to luminous intensity (IV) and dominant wavelength (λD) bins shown. Orders for LC503TBL1-30Q-A1 may be filled with any or all bins contained as below. All luminous intensity (IV) and dominant wavelength (λD) values shown and specified are at IF = 20 mA. Luminous Intensity (IV) X4 X5 X or above 4180 mcd W 3000 mcd V 2130 mcd U 1520 mcd 465 nm 470 nm 475 nm Dominant Wavelength (λD) Important Notes: 1. All ranks will be included per delivery; rank ratio will be based on the dice distribution. 2. Pb content <1000 ppm. 3. Tolerance of measurement of luminous intensity is ±15%. 4. Tolerance of measurement of dominant wavelength is ±1 nm. 5. Tolerance of measurement of VF is ±0.05 V. 6. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document. 7. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions. 8. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED product safely. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT063.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Document No. SPE/LC503TBL1-30P-A1 Rev. No. 02 Graphs Graphs tems pared by 100.0 -50 If (mA) -40 -30 -20 0 0.0 -10.0 80.0 -20.0 60.0 -30.0 40.0 -40.0 20.0 0.0 3.0 3.4 3.8 4.2 4.6 5.0 FIG.1 FORWARD CURRENT VS. FORWARD VOLTAGE. Vf(V) -50.0 Ir(uA) FIG.2 REVERSE CURRENT VS. REVERSE VOLTAGE. Half Power WL=28nm Domi WL= 470nm I (RELATIVE LUMINOUS INTENSITY) 100% 5.0 4.0 75% 3.0 50% 2.0 25% 1.0 0.0 0.0 If(mA) 20.0 40.0 60.0 0% 300 80.0 100.0 FIG.3 RELATIVE LUMINOUS INTENSITY VS. FORWARD CURRENT 50 400 500 600 WL(nm) 800 700 FIG.4 RELATIVE LUMINOUS INTENSITY VS. WAVELENGTH. 50% Power Angle : 30 IF(mA) Ie(%) 0 40 100% 30 80% 20 60% 10 40% 0 Ta( C) 0.0 20.0 40.0 60.0 80.0 100.0 0% FIG.5 MAXIMUM FORWARD DC CURRENT VS AMBIENT TEMPERATURE (Tjmax=105 C) Signatures Date LiuZM 2006-03-31 20% -90 -60 -30 0 CLD-CT063.000 David 2006-03-31 30 90 60 FIG.6 FAR FIELD PATTERN Revision History Rev. No Date Change Description © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Aldosin 2006-03-31 02 2006-03-31 Cancel VF bin. cked byCopyright Cree logo are registered trademarks of Cree, Inc. roved by -10 Vr(V) Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Mechanical Dimensions Document No. SPE/LC503TBL1-30Q-A1 Rev. No. 02 All dimensions are in mm. Tolerance is ±0.25 mm unless otherwise noted. An epoxy meniscus may extend about 1.5 mm down the leads. Dimension Drawing Burr around bottom of epoxy may be 0.5 mm max. C ute maximum Rating Unit 25 mA 100 mA 5 V 100 mW 40 ~ +95 °C 0 ~ +100 °C 260°C for 3 sec Max. Notes m the base of the epoxy bulb) RoHS Compliance stics The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the °C) permitted for such substances, or are used in an exempted application, in accordance with EU Direc( threshold Ta = 25limits) tive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS), as amended through April 21, 2006. Vision Advisory Claim Condition Min. Typ. Max. Unit IF = 20mA --- 3.4 4.0 V Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. IF = 1.0P$ 1.7 CLD-CT063.000 --- 2.5 V Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Kit Number System Cree LED lamps are tested and sorted into performance bins. A bin is specified by ranges of color, forward voltage, and brightness. Sorted LEDs are packaged for shipping in various convenient options. Please refer to the “Cree LED Lamp Packaging Standard” document for more information about shipping and packaging options. Cree LEDs are sold by order codes in combinations of bins called kits. Order codes are configured in the following manner: Standard/Custom 0: Standard C: Custom VF 0: Full forward voltage distribution 1~9, A~Z . . . : special request * Wd/Color 1: Full-color distribution 2~9, A~Z . . . : special request * aaaaaaaaa-aaa-aa- x x x x x IV 0: Full luminous intensity distribution 1~9, A~Z . . . :special request * Packing type 0: Standard = Bulk pack 1~9, A~Z . . . : special request * Product P/N * Contact your Cree sales representative for ordering information. Standard Available Kits* Kit Number Description LC503TBL1-30Q-A1-00001 5mm Round 30 Blue 470nm, FULL RANK, Bulk Pack LC503TBL1-30Q-A1-00011 5mm Round 30 Blue 470nm, V or above, Bulk Pack * Please contact your Cree representative about the availability of non-standard kits. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT063.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps