D100ER Series Low Cost, 1W SIP Tightly Regulated DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Key Features: Parameter Conditions Min. Typ. Max. 5 VDC Input 4.75 5.0 5.25 12 VDC Input 11.4 12.0 12.6 24 VDC Input 22.8 24.0 25.2 • 1W Output Power • Tightly Regulated • Single & Dual Outputs • Miniature SIP Case • 1,000 VDC Isolation Input Voltage Range Input Filter Units VDC Internal Capacitor Reverse Polarity Input Current 0.3 A Max. Units Output • >3.5 MHour MTBF Parameter • 24 Standard Models Output Voltage Accuracy • Industry Standard Pin-Out Output Voltage Balance • LOWEST COST!! Line Regulation Load Regulation (Note 1) Conditions Min. Typ. ±3.0 % ±1.0 % For Vin Min to Max ±0.25 % For Iout = 10% to 100% ±1.0 % 20 mV P - P ±0.03 %/ºC Max. Units Dual Output , Balanced Loads ±0.1 Ripple & Noise (20 MHz) (Note 3) 10 Output Power Protection 120 % Temperature Coefficient Output Short Circuit Momentary (1.0 Sec.) General Parameter Conditions Isolation Voltage RoHS Compliant Isolation Resistance Isolation Capacitance Min. 60 Seconds 1,000 500 VDC 1,000 100 kHz, 1V Switching Frequency Typ. VDC MΩ 60 pF 100 kHz Environmental Min. Typ. Max. Operating Temperature Range Parameter Conditions Ambient -40 +25 +85 ºC Operating Temperature Range Case -40 +90 ºC -55 +125 ºC 95 % Storage Temperature Range Cooling Humidity Units Free Air Convection RH, Non-condensing MicroPower Direct Physical 292 Page Street Suite D Stoughton, MA 02072 USA Case Size (Single Output) 0.77 x 0.24 x 0.40 Inches (19.6 x 6.0 x 10.2 mm) Case Size (Dual Output) 1.08 x 0.37 x 0.47 Inches (27.5 x 9.5 x 12.0 mm) T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Reliability Specifications Case Material Non-Conductive Black Plastic (UL94-V0) Weight Parameter MTBF 0.07 Oz (2.1g) Conditions Min. MIL HDBK 217F, 25ºC, Gnd Benign Typ. Max. 3.5 Units MHours Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Conditions Min. Typ. Max. 5 VDC Input -0.7 9.0 12 VDC Input -0.7 18.0 24 VDC Input -0.7 30.0 Units VDC 1.5 mm From Case For 10 Sec 300 ºC All Models 450 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number D101ER D102ER D103ER D104ER D105ER D106ER D107ER D108ER D111ER D112ER D113ER D114ER D115ER D116ER D117ER D118ER D121ER D122ER D123ER D124ER D125ER D126ER D127ER D128ER Input Voltage (VDC) Current (mA) Nominal Range Full-Load No-Load 5 4.75 - 5.25 294 30 5 4.75 - 5.25 286 30 5 4.75 - 5.25 282 30 5 4.75 - 5.25 278 30 5 4.75 - 5.25 290 30 5 4.75 - 5.25 286 30 5 4.75 - 5.25 278 30 5 4.75 - 5.25 278 30 12 11.4 - 12.6 121 15 12 11.4 - 12.6 117 15 12 11.4 - 12.6 116 15 12 11.4 - 12.6 116 15 12 11.4 - 12.6 119 15 12 11.4 - 12.6 116 15 12 11.4 - 12.6 114 15 12 11.4 - 12.6 114 15 24 22.8 - 25.2 59 8 24 22.8 - 25.2 58 8 24 22.8 - 25.2 57 8 24 22.8 - 25.2 57 8 24 22.8 - 25.2 58 8 24 22.8 - 25.2 58 8 24 22.8 - 25.2 57 8 24 22.8 - 25.2 57 8 Output Voltage Current Current (VDC) (mA, Max) (mA, Min) 5.0 200.0 20.0 9.0 111.0 12.0 12.0 83.0 9.0 15.0 67.0 7.0 ±5.0 ±100.0 ±10.0 ±9.0 ±56.0 ±6.0 ±12.0 ±42.0 ±5.0 ±15.0 ±33.0 ±4.0 5.0 150.0 15.0 9.0 111.0 12.0 12.0 83.0 9.0 15.0 67.0 7.0 ±5.0 ±100.0 ±10.0 ±9.0 ±56.0 ±6.0 ±12.0 ±42.0 ±5.0 ±15.0 ±33.0 ±4.0 5.0 150.0 15.0 9.0 111.0 12.0 12.0 83.0 9.0 15.0 67.0 7.0 ±5.0 ±100.0 ±10.0 ±9.0 ±56.0 ±6.0 ±12.0 ±42.0 ±5.0 ±15.0 ±33.0 ±4.0 Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. An input capacitor will enhace stability Output Capacitor over temperature and Input Vin Vout input line variations. Capacitor Single Dual Recommended capaci5 VDC 4.7 μF 5 VDC 10.0 μF 4.7 μF tor values are given in 2.2 μF 9 VDC 4.7 μF 2.2 μF the table at right. For 12 VDC applications requir- 24 VDC 1.0 μF 12 VDC 2.2 μF 1.0 μF ing very low output 15 VDC 1.0 μF 0.47 μF noise levels, a simple LC filter should be effective. 4. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Efficiency (%, Typ) 68 70 71 72 69 70 72 72 69 71 72 72 70 72 73 73 70 72 73 73 72 72 73 73 Fuse Rating Slow-Blow (mA) 500 500 500 500 500 500 500 500 200 200 200 200 200 200 200 200 100 100 100 100 100 100 100 100 Derating Curve Mechanical Dimensions (Single Output) Mechanical Dimensions (Dual Output) Pin Connections Pin Single 1 2 4 6 7 9 10 +Vin +Vin -Vin -Vin -Vout No Pin +Vout No Pin No Pin +Vout No Pin -Vout No Pin Common Dual MicroPower Direct www.micropowerdirect.com 292 Page Street, STE D, Stoughton, MA 02072 • TEL: (781) 344-8226 Notes: • All dimen dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is ma marked by a “dot” or indentation on the sid side of the unit • FAX: (781) 344-8481 • E-Mail: [email protected]