STL60NH3LL N-channel 30V - 0.0065Ω - 30A - PowerFLAT™ (6x5) Ultra low gate charge STripFET™ Power MOSFET General features Type VDSS RDS(on) ID STL60NH3LL 30V <0.0085Ω 16A (2) ■ Improved die-to-footprint ratio ■ Very low profile package (1mm max) ■ Very low thermal resistance ■ Very low gate charge ■ Low threshold device PowerFLAT™(6x5) Description This application specific Power MOSFET is the latest generation of STMicroelectronics unique “STripFET™” technology. The resulting transistor is optimized for low on-resistance and minimal gate charge. The Chip-scaled PowerFLAT™ package allows a significant board space saving, still boosting the performance. Internal schematic diagram Applications ■ Switching application Order codes Part number Marking Package Packaging STL60NH3LL L60NH3LL PowerFLAT™ (6 x 5) Tape & reel September 2006 Rev 5 1/13 www.st.com 13 Contents STL60NH3LL Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 Electrical characteristics (curves) ............................ 6 3 Test circuit 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2/13 ................................................ 9 STL60NH3LL 1 Electrical ratings Electrical ratings Table 1. Absolute maximum ratings Symbol Parameter Value Unit 30 V ± 16 V Drain current (continuous) at TC = 25°C 30 A ID (1) Drain current (continuous) at TC = 100°C 30 A ID(2) Drain current (continuous) at TC = 25°C 16 A VDS Drain-source voltage (VGS = 0) VGS Gate-source voltage ID (1) (3) Drain current (pulsed) 64 A PTOT(1) Total dissipation at TC = 25°C 60 W PTOT(2) Total dissipation at TC = 25°C 4 W 0.03 W/°C -55 to 150 °C Value Unit 2.08 °C/W 31.3 °C/W IDM Derating factor Tj Tstg Operating junction temperature Storage temperature 1. The value is rated according Rthj-C and is limited by wire bonding. 2. This value is according Rthj-pcb 3. Pulse width limited by safe operating area Table 2. Thermal resistance Symbol Rthj-case Parameter Thermal resistance junction-case (drain) Max Rthj-pcb (1) Thermal resistance junction-pcb Max 1. When mounted on FR-4 board of 1inch2, 2 oz Cu, t<10sec 3/13 Electrical characteristics 2 STL60NH3LL Electrical characteristics (TCASE=25°C unless otherwise specified) Table 3. Symbol Parameter Test condictions Drain-source breakdown voltage ID = 250µA, VGS= 0 IDSS Zero gate voltage drain current (VGS = 0) VDS = Max rating, VDS = Max rating,@125°C IGSS Gate body leakage current (VDS = 0) VDS = ± 16V VGS(th) Gate threshold voltage VDS= VGS, ID = 250µA RDS(on) Static drain-source on resistance VGS= 10V, ID= 8A VGS= 4.5V, ID= 8A V(BR)DSS Table 4. Symbol 4/13 On/off states Min. Typ. Max. 30 Unit V 1 10 µA µA ±100 nA 1 V 0.0065 0.0085 0.0075 0.0105 Ω Ω Dynamic Parameter Test condictions Ciss Coss Crss Input capacitance Output capacitance Reverse transfer capacitance VDS=25V, f = 1MHz, VGS=0 Qg Qgs Qgd Total gate charge Gate-source charge Gate-drain charge VDD = 15V, ID = 16A, VGS = 4.5V (see Figure 15) RG Gate input resistance f=1 MHz Gate DC Bias = 0 Test signal level = 20mV open drain Min. Typ. Max. 1810 565 41 0.5 Unit pF pF pF 18 4.8 5.3 24 nC nC nC 1.5 3 Ω STL60NH3LL Electrical characteristics Table 5. Symbol Switching times Parameter Test condictions Min. Typ. Max. Unit td(on) tr Turn-on delay time Rise time VDD = 15V, ID = 8A RG= 4.7Ω, VGS= 10V, (see Figure 14) 8 65 ns ns td(off) tf Turn-off delay time Fall time VDD = 15V, ID = 8A RG= 4.7Ω, VGS= 10V, (see Figure 14) 30 20 ns ns Table 6. Symbol ISD ISDM VSD (1) trr Qrr IRRM Source drain diode Parameter Test condictions Min Typ. Source-drain current Source-drain current (pulsed) Forward on voltage ISD = 16A, VGS = 0 Reverse recovery time Reverse recovery charge Reverse recovery current ISD = 16V, di/dt = 100A/µs VDD = 20V, Tj = 25°C (see Figure 16) 22 32 1.9 Max Unit 16 64 A A 1.3 V ns nC A 1. Pulsed: Pulse duration = 300µs, duty cycle 1.5% 5/13 Electrical characteristics STL60NH3LL 2.1 Electrical characteristics (curves) Figure 1. Safe operating area Figure 2. Thermal impedance Figure 3. Output characterisics Figure 4. Transfer characteristics Figure 5. Normalized BVDSS vs temperature Figure 6. Static drain-source on resistance 6/13 STL60NH3LL Electrical characteristics Figure 7. Gate charge vs gate-source voltage Figure 8. Figure 9. Normalized gate threshold voltage vs temperature Capacitance variations Figure 10. Normalized on resistance vs temperature Figure 11. Source-drain diode forward characteristics 7/13 Electrical characteristics STL60NH3LL Figure 12. Allowable Iav vs Time in Avalanche Figure 13. Allowable Iav vs Time in Avalanche The previous curve gives the single pulse safe operating area for unclamped inductive loads under the following conditions: PD(AVE) =0.5*(1.3*BVDSS *IAV ) EAS(AR) =PD(AVE) *tAV Where: IAV is the allowable current in avalanche PD(AVE) is the average power dissipation in avalanche (single pulse) tAV is the time in avalanche 8/13 STL60NH3LL 3 Test circuit Test circuit Figure 14. Switching times test circuit for resistive load Figure 15. Gate charge test circuit Figure 16. Test circuit for inductive load Figure 17. Unclamped inductive load test switching and diode recovery times circuit Figure 18. Unclamped inductive waveform Figure 19. Switching time waveform 9/13 Package mechanical data 4 STL60NH3LL Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 10/13 STL60NH3LL Package mechanical data PowerFLAT™ (6x5) MECHANICAL DATA mm. inch DIM. A MIN. TYP MAX. MIN. TYP. 0.80 0.83 0.93 0.031 0.032 0.036 0.02 0.05 0.0007 0.0019 A1 A3 b 0.20 0.35 0.40 0.007 0.47 0.013 0.015 D 5.00 0.196 D1 4.75 0.187 D2 4.15 4.20 4.25 0.163 0.165 E 6.00 0.236 E1 5.75 0.226 E2 3.43 3.48 3.53 E4 2.58 2.63 2.68 e L 0.135 1.27 0.70 0.80 MAX. 0.018 0.167 0.137 0.139 0.103 0.105 0.050 0.90 0.027 0.031 0.035 11/13 Revision history 5 STL60NH3LL Revision history Table 7. 12/13 Revision history Date Revision Changes 10-Jan-2006 1 First release 14-Apr-2006 2 New footprint 03-Jul-2006 3 New Ecopack label 01-Aug-2006 4 Modified Figure 1. and Figure 2. 05-Sep-2006 5 New template, no content change STL60NH3LL Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 13/13