LM321 Single Channel Operational Amplifier LM321 is a general purpose, single channel op amp with internal compensation and a true differential input stage. This op amp features a wide supply voltage ranging from 3 V to 32 V for single supplies and ±1.5 to ±16 V for split supplies, suiting a variety of applications. LM321 is unity gain stable even with large capacitive loads up to 1.5 nF. LM321 is available in a space-saving TSOP−5/SOT23−5 package. www.onsemi.com 5 1 Features • • • • • • • • Wide Supply Voltage Range: 3 V to 32 V Short Circuit Protected Outputs True Differential Input Stage Low Input Bias Currents Internally Compensated Single and Split Supply Operation Unity Gain Stable with 1.5 nF Capacitive Load This Device is Pb-Free, Halogen Free/BFR Free and is RoHS Compliant TSOP−5 CASE 483 PIN CONNECTION IN+ 1 VEE 2 IN− 3 5 VCC 4 OUT Typical Applications • Gain Stage • Active Filter • Signal Processing MARKING DIAGRAM 5 ADYAYWG G 1 ADY = Specific Device Code A = Assembly Location Y = Year W = Work Week G = Pb-Free Package (Note: Microdot may be in either location) ORDERING INFORMATION Device Package Shipping† LM321SN3T1G TSOP−5 (Pb−Free) 3000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. © Semiconductor Components Industries, LLC, 2015 November, 2015 − Rev. 2 1 Publication Order Number: LM321/D LM321 Table 1. ABSOLUTE MAXIMUM RATINGS (Over operating free-air temperature, unless otherwise stated) Parameter Rating Unit 36 V Input Voltage VEE – 0.3 to 32 V Input Current ±10 mA Supply Voltage INPUT AND OUTPUT PINS Output Short Circuit Duration (Note 1) Continuous TEMPERATURE Operating Temperature –40 to +125 °C Storage Temperature –65 to +150 °C Junction Temperature –65 to +150 °C Human Body Model (HBM) 200 V Charged Device Model (CDM) 800 V Machine Model (MM) 100 V 100 mA ESD RATINGS (Note 2) OTHER RATINGS Latch-Up Current (Note 3) MSL Level 1 Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Short circuits can cause excessive heating and eventual destruction. 2. This device series incorporates ESD protection and is tested by the following methods: ESD Human Body Model tested per JEDEC standard: JESD22−A114 ESD Machine Model tested per JEDEC standard: JESD22−A115 3. Latch-up Current tested per JEDEC standard: JESD78 Table 2. THERMAL INFORMATION (Note 4) Parameter Junction to Ambient Symbol Package Value Unit qJA TSOP−5/SOT23−5 235 °C/W 4. As mounted on an 80 × 80 × 1.5 mm FR4 PCB with 650 mm2 and 2 oz (0.034 mm) thick copper heat spreader. Following JEDEC JESD/EIA 51.1, 51.2, 51.3 test guidelines. Table 3. RECOMMENDED OPERATING CONDITIONS Parameter Supply Voltage (VCC − VEE) Specified Operating Range Common Mode Input Voltage Range Symbol Range Unit VS 3 to 32 V TA −40 to 85 °C VCM VEE to VCC−1.7 V Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. www.onsemi.com 2 LM321 Table 4. ELECTRICAL CHARACTERISTICS − VS = 5 V (At TA = +25°C, RL = 10 kW connected to mid-supply, VCM = VOUT = mid-supply, unless otherwise noted. Boldface limits apply over the specified temperature range, TA = –40°C to 85°C, guaranteed by characterization and/or design.) Min Typ Max VS = 5 V, VCM = VEE to VCC – 1.7 V TA = 25°C TA = –40°C to 85°C − − 0.3 − 7 9 DVOS/DT TA = –40°C to 85°C − 7 − mV/°C Input Bias Current IIB TA = 25°C TA = –40°C to 85°C − − −10 − − −500 nA Input Offset Current IOS TA = 25°C TA = –40°C to 85°C − − 1 − − 150 nA Parameter Symbol Conditions Unit INPUT CHARACTERISTICS Offset Voltage Offset Voltage Drift vs Temp Common Mode Rejection Ratio VOS CMRR mV VCM = VEE to VCC – 1.7 V 65 85 − dB Input Resistance RIN Differential Common Mode − − 85 300 − − GW Input Capacitance CIN Differential Common Mode − − 0.6 1.6 − − pF − 100 − dB OUTPUT CHARACTERISTICS Open Loop Voltage Gain AVOL − 1,200 − W RL = 2 kW to VEE RL = 10 kW to VEE VCC–1.8 VCC−1.8 VCC−1.4 VCC−1.4 − − V RL = 10 kW to VCC − VEE+0.8 VEE+1.0 V Sinking Current VS = 5 V VS = 15 V 10 10 20 20 − − Sourcing Current VS = 5 V VS = 15 V 20 20 40 40 − − CL Phase Margin = 15° − 1,500 − pF eN fIN = 1 kHz − 40 − nV/√Hz GBWP CL = 25 pF, RL to VCC − 750 − kHz Gain Margin AM CL = 25 pF, RL to VCC − 14 − dB Phase Margin aM CL = 25 pF, RL to VCC − 60 − ° Slew Rate SR CL = 25 pF, RL = ∞ − 0.3 − V/ms VS = 5 V to 32 V 62 100 − dB No Load − 0.25 0.5 mA Open Loop Output Impedance ZOUT_OL Output Voltage High VOH Output Voltage Low VOL Output Current Capability Output Current Capability Capacitive Load Drive IO IO f = UGBW, IO = 0 mA mA mA NOISE PERFORMANCE Voltage Noise Density DYNAMIC PERFORMANCE Gain Bandwidth Product POWER SUPPLY Power Supply Rejection Ratio Quiescent Current PSRR IQ Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. www.onsemi.com 3 LM321 Table 5. ELECTRICAL CHARACTERISTICS − VS = 32 V (At TA = +25°C, RL = 10 kW connected to mid-supply, VCM = VOUT = mid-supply, unless otherwise noted. Boldface limits apply over the specified temperature range, TA = –40°C to 85°C, guaranteed by characterization and/or design.) Parameter Symbol Conditions Min Typ Max Unit VOS VS = 32 V, VCM = VEE to VCC – 1.7 V TA = 25°C TA = –40°C to 85°C − − 0.3 − 7 9 TA = –40°C to 85°C − 7 − mV/°C VCM = VEE to VCC – 1.7 V − 100 − dB TA = 25°C TA = –40°C to 85°C − 84 100 − − − dB f = UGBW, IO = 0 mA − 2,000 − W INPUT CHARACTERISTICS Offset Voltage Offset Voltage Drift vs Temp Common Mode Rejection Ratio DVOS/DT CMRR mV OUTPUT CHARACTERISTICS Open Loop Voltage Gain Open Loop Output Impedance AVOL ZOUT_OL Output Voltage High VOH RL = 2 kW to VEE RL = 10 kW to VEE VCC−2.5 VCC−2.5 VCC−2.0 VCC−1.5 − − V Output Voltage Low VOL RL = 10 kW to VCC − VEE+1.0 VEE+1.5 V Capacitive Load Drive CL Phase Margin = 15° − 1,500 − pF eN NOISE PERFORMANCE Voltage Noise Density Total Harmonic Distortion + Noise fIN = 1 kHz − 40 − nV/√Hz THD+N VS = 30 V, fIN = 1 kHz, RL to VCC − 0.02 − % DYNAMIC PERFORMANCE GBWP CL = 25 pF, RL to VCC − 900 − kHz Gain Margin AM CL = 25 pF, RL to VCC − 18 − dB Phase Margin aM CL = 25 pF, RL to VCC − 66 − ° Slew Rate SR CL = 25 pF, RL = ∞ − 0.4 − V/ms VS = 5 V to 32 V 62 100 − dB No Load, VS = 32 V − 0.3 1.2 mA Gain Bandwidth Product POWER SUPPLY Power Supply Rejection Ratio Quiescent Current PSRR IQ Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. www.onsemi.com 4 LM321 TYPICAL CHARACTERISTICS 100 80 AVOL (dB) 60 270 110 240 100 180 40 150 20 120 90 0 PHASE MARGIN 80 30 CL = 25 pF −60 10 100 1k 10k 100k 60 50 40 20 RL = 10 kW −40 70 30 60 −20 10 0 10M 1M VS = 3 V VS = 5 V VS = 32 V 90 210 CMRR (dB) VS = 3 V, Gain VS = 5 V, Gain VS = 32 V, Gain VS = 3 V, Phase VS = 5 V, Phase VS = 32 V, Phase Phase Margin (5) 120 0 100 10 1k Frequency (Hz) 10k 100k 1M Frequency (Hz) Figure 1. Open Loop Gain and Phase Margin vs. Frequency Figure 2. CMRR vs. Frequency 4 0.1 VS = 10 V Input Output RL = 10 kW 3 VS = 5.0 V 0.08 CL = 15 pF Input Output RL = 10 kW CL = 15 pF 0.06 2 0.04 Voltage (V) Voltage (V) 1 0 −1 0.02 0.0 −0.02 −0.04 −2 −0.06 −3 −4 −10 −0.08 0 10 20 30 40 50 60 70 80 −0.1 −2 90 100 0 2 Time (ms) 6 8 10 12 14 Time (ms) Figure 3. Inverting Large Signal Step Response Figure 4. Inverting Small Signal Step Response 1000 60 Voltage Noise Density (nV//Hz) VS = 3 V VS = 5 V 50 VS = 32 V Phase Margin (5) 4 40 30 20 10 AV = 11 V/V VS = 3 V RL = 10 kW VS = 5 V VS = 32 V 100 10 0 100 200 300 500 1000 1 1500 10 100 1k 10k 100k Frequency (Hz) Load Capacitance (pF) Figure 5. Phase Margin vs. Load Capacitance Figure 6. Voltage Noise Density vs. Frequency www.onsemi.com 5 LM321 TYPICAL CHARACTERISTICS 1000 0.35 Quiescent Current (mA) THD+N (%) 0.30 100 0.25 0.20 0.15 0.10 VS = 3 V VS = 5 V 0.05 VS = 32 V 10 10 100 1k 10k 0.00 −40 100k −20 Frequency (Hz) 0.8 0.6 0.6 Input Offset Voltage (mV) Input Offset Voltage (mV) 40 60 0.4 0.2 0.0 VS = 3 V T= −40°C T= 25°C 100 0.4 0.2 0.0 VS = 5 V −0.2 T= −40°C T= 25°C −0.4 T= 85°C T= 85°C −0.6 −0.6 0 0.1 0.2 0.25 0.5 0.7 1 1.25 1.3 1.4 1.5 0 0.5 Common Mode Voltage (V) 1 1.5 2 2.5 3 3.5 Common Mode Voltage (V) Figure 9. Input Offset Voltage vs. Common Mode Voltage at 3 V Supply Figure 10. Input Offset Voltage vs. Common Mode Voltage at 5 V Supply 10 0.8 VCM = VS/2 8 0.6 IIB− 6 0.4 IIB+ IOS 4 Current (nA) Input Offset Voltage (mV) 80 Figure 8. Quiescent Current vs. Temperature 0.8 −0.4 20 Temperature (5C) Figure 7. THD+N vs. Frequency −0.2 0 0.2 0.0 VS = 32 V −0.2 2 0 −2 −4 T= −40°C −6 T= 25°C −0.4 −8 T= 85°C −0.6 0 5 10 15 20 25 −10 −40 30 Common Mode Voltage (V) −20 0 20 40 60 80 100 Temperature (5C) Figure 11. Input Offset Voltage vs. Common Mode Voltage at 32 V Supply Figure 12. Input Bias and Offset Current vs. Temperature www.onsemi.com 6 LM321 3.0 1400 2.5 1200 VOL − VEE (mV) VCC − VOH (V) TYPICAL CHARACTERISTICS 2.0 1.5 1.0 VS = 3 V 1000 800 600 VS = 3 V 400 T= −40°C 0.5 T= −40°C T= 25°C T= 25°C 200 T= 85°C T= 85°C 0 0 0 5 10 15 20 25 30 0 5 Output Source Current (mA) Figure 13. High Level Output Voltage Swing vs. Output Current at 3 V Supply 15 20 Figure 14. Low Level Output Voltage Swing vs. Output Current at 3 V Supply 1800 5.0 VS = 5 V 4.5 1600 T= −40°C 4.0 1400 T= 25°C 3.5 T= 85°C VOL − VEE (mV) VCC − VOH (V) 10 Output Sink Current (mA) 3.0 2.5 2.0 1.5 1200 1000 800 600 VS = 5 V 400 1.0 T= −40°C T= 25°C 0.5 200 0 0 0 5 10 15 20 25 30 T= 85°C 0 5 Output Source Current (mA) Figure 15. High Level Output Voltage Swing vs. Output Current at 5 V Supply 15 20 Figure 16. Low Level Output Voltage Swing vs. Output Current at 5 V Supply 8 5.0 VS = 32 V 4.5 VS = 32 V 7 T= −40°C 4.0 T= 25°C 3.5 T= −40°C T= 25°C 6 T= 85°C T= 85°C VOL − VEE (V) VCC − VOH (V) 10 Output Sink Current (mA) 3.0 2.5 2.0 5 4 3 1.5 2 1.0 1 0.5 0 0 0 5 10 15 20 25 30 0 Output Source Current (mA) 3 6 9 12 15 18 21 24 27 30 Output Sink Current (mA) Figure 17. High Level Output Voltage Swing vs. Output Current at 32 V Supply Figure 18. Low Level Output Voltage Swing vs. Output Current at 5 V Supply32 www.onsemi.com 7 LM321 APPLICATION INFORMATION CIRCUIT DESCRIPTION splitting the collectors of Q20 and Q18. Another feature of this input stage is that the input common mode range can include the negative supply or ground, in single supply operation, without saturating either the input devices or the differential to single−ended converter. The second stage consists of a standard current source load amplifier stage. Each amplifier is biased from an internal−voltage regulator which has a low temperature coefficient thus giving each amplifier good temperature characteristics as well as excellent power supply rejection. The LM321 is made using two internally compensated, two−stage operational amplifiers. The first stage of each consists of differential input devices Q20 and Q18 with input buffer transistors Q21 and Q17 and the differential to single ended converter Q3 and Q4. The first stage performs not only the first stage gain function but also performs the level shifting and transconductance reduction functions. By reducing the transconductance, a smaller compensation capacitor (only 5.0 pF) can be employed, thus saving chip area. The transconductance reduction is accomplished by Output Bias Circuitry VCC Q15 Q16 Q22 Q14 Q13 40 k Q19 5.0 pF Q12 Q24 25 Q23 Q20 Q18 Inputs Q11 Q9 Q21 Q17 Q6 Q2 Q25 Q7 Q5 Q1 Q8 Q3 Q4 Q10 Q26 2.4 k 2.0 k VEE/Gnd Figure 19. LM321 Representative Schematic Diagram www.onsemi.com 8 LM321 VCC LM321 has a class B output stage, which is comprised of push−pull transistors. This type of output is inherently subject to crossover distortion near mid−rail where neither push or pull transistors are conducting. Several techniques can be used to minimize crossover distortion. Connecting the output load to either the positive or negative supply rail instead of mid−rail can reduce the crossover distortion. Additionally, increasing the load resistance relatively decreases the amount of crossover distortion. OUT VEE Figure 20. Simplified Class B Output Figure 21. Sine wave with crossover distortion www.onsemi.com 9 LM321 PACKAGE DIMENSIONS TSOP−5 CASE 483 ISSUE L NOTE 5 2X NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE. DIMENSION A. 5. OPTIONAL CONSTRUCTION: AN ADDITIONAL TRIMMED LEAD IS ALLOWED IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. D 5X 0.20 C A B 0.10 T M 2X 0.20 T B 5 1 4 2 S 3 K B DETAIL Z G A A TOP VIEW DIM A B C D G H J K M S DETAIL Z J C 0.05 H SIDE VIEW C SEATING PLANE END VIEW MILLIMETERS MIN MAX 3.00 BSC 1.50 BSC 0.90 1.10 0.25 0.50 0.95 BSC 0.01 0.10 0.10 0.26 0.20 0.60 0_ 10 _ 2.50 3.00 SOLDERING FOOTPRINT* 0.95 0.037 1.9 0.074 2.4 0.094 1.0 0.039 0.7 0.028 SCALE 10:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and the are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 10 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative LM321/D