BCM5226 ® 10/100BASE-TX/FX HEX-Φ™ TRANSCEIVER FEATURES • • • • • • • • • • • • • • • • • SUMMARY OF BENEFITS Single-chip six-port Fast Ethernet transceiver • • • • HP Auto-MDIX Low-power 2.5V CMOS technology Compatible with 2.5V I/O and 3.3V I/O Reduced Media Independent Interface (RMII) Serial Media Independent Interface (SMII) • Fully integrated digital adaptive equalization • On-chip multimode transmit waveshaping Edge-rate control eliminates external filters Integrated baseline wander correction • Full-duplex support Target usage: Fast Ethernet switches. Low power < 300 milliwatts per port. Auto-MDIX detects and corrects cabling errors. Provides robust performance over a broad range of operating conditions. Single-chip device contains six independent Fast Ethernet transceivers. Performs all physical layer interface functions for 100BASETX full-duplex or half-duplex Ethernet on Category 5 twistedpair cable and 10BASE-T full- or half-duplex Ethernet on Category 3, 4, or 5 cable. Permits transmission over fiber-optic cabling when paired with an external fiber-optic transceiver. Compliant with IEEE 802.3 standard. • • IEEE 1149.1 (JTAG) scan chain support. Twisted-pair or fiber support on any or all ports Interrupt output capability Loopback mode for diagnostics 160-pin PQFP (BCM5226R) 128-pin PQFP (BCM5226S) Proven Broadcom proprietary DSP Digi-Φ™ architecture Quad BCM5208 Versus HEX BCM5226 Comparison 6 Active PHY components + 6 MACs including switch fabric 4 Active SMII PHY components + SMII MACs embedded in switch chip Switch Fabric and System Logic Switch Fabric with Embedded MACs QUAD MAC QUAD MAC 24x16=384 MII Pins 24x2=48 SMII Pins BCM5208 Port 1 BCM5208 Port 24 BCM5226 Port 1 BCM5226 BCM5226 BCM5226 Port 24 OVERVIEW TXD [3:0] 4 TXEN TXER Multimode Xmt DAC TD+/- Auto MDIX 10BASE-T PCS Baseline Wander Correction 2 Clock Generator BIAS Bias Generator JTAG 5 JTAG TAP+BS REF_CLK or SMII RXDV Digital Adaptive Equalizer CRS_DV RX_ER RXER RXD[1:0] 2 4 AutoNegotiation/ Link Integrity CRS/Link Detection RFF_CLK MII to RMII CRS RXD[3:0] SD+/- TXEN TXC RXC ADC TXD [1:0] COL 100BASE-X PCS RD+/- 12 Clock Recovery MDC MII Registrers MII Mgmt Control MDIO The Broadcom ® BCM5226 is a single-chip device containing six independent Fast Ethernet transceivers. Each performs all the physical layer interface functions for 100BASE-TX full-duplex or half-duplex Ethernet on Category 5 twisted-pair cable and 10BASE-T full or halfduplex Ethernet on Category 3, 4 or 5 cable. Each port may also be configured for 100BASE-FX full or half-duplex transmission over fiberoptic cabling when paired with an external fiber-optic line transceiver. The BCM5226 chip performs 4B5B, MLT3, NRZI, and Manchester encoding and decoding, clock and data recovery, stream cipher scrambling/descrambling, digital adaptive equalization, line transmission, carrier sense and link integrity monitoring, autonegotiation and RMII management functions. The BCM5226 can be connected to a switch controller through the RMII on one side and connects directly to the network media on the other side through isolation transformers for UTP modes or fiber-optic transceiver components for FX mode. The BCM5226 is compliant with the IEEE 802.3 standard. The BCM5226 operates from a 2.5V power supply, which dramatically lowers total power consumption compared to 3.3V and 5V designs. The BCM5226 I/O operates at either 2.5V or 3.3V, for compatibility with 3.3V designs. The BCM5226 is the first 10/100 Ethernet transceiver to incorporate the Hewlett-Packard auto-Media Dependent Interface Crossover (AutoMDIX) feature. Originally specified in the IEEE 802.3ab Gigabit Ethernet standard for Category 5 cable, the Auto-MDIX feature enables the transceiver to automatically detect and correct a crossed cable. This allows system installation and maintenance personnel to use crossover or straight-through cables interchangeably, regardless of whether the cable is attached to another switch, network interface card or repeater. This capability eliminates incorrect connections due to cable mismatch, making it easier and less expensive to install and operate 10/100 Ethernet switches. The BCM5226R supports RMII, and is available in a 160-pin plastic quad flatpack package (PQFP); the BCM5226R supports SMII, and is available in a 128-pin PQFP. Broadcom®, the pulse logo, and Connecting everything® are trademarks of Broadcom Corporation and/ or its subsidiaries in the United States and certain other countries. All other trademarks mentioned are the property of their respective owners. ® BROADCOM CORPORATION 16215 Alton Parkway, P.O. Box 57013 Irvine, California 92619-7013 © 2004 by BROADCOM CORPORATION. All rights reserved. 5226-PB06-R 04/07/04 Phone: 949-450-8700 Fax: 949-450-8710 E-mail: [email protected] Web: www.broadcom.com