ON MUR210 Switchmodee power rectifier Datasheet

MUR210
Preferred Device
SWITCHMODE
Power Rectifier
. . . designed for use in switching power supplies, inverters and as
free wheeling diodes, these state–of–the–art devices have the
following features:
•
•
•
•
•
http://onsemi.com
Ultrafast 20 Nanosecond Recovery Times
175°C Operating Junction Temperature
Low Forward Voltage
Low Leakage Current
High Temperature Glass Passivated Junction
ULTRAFAST
RECTIFIERS
2 AMPERES
100 VOLTS
Mechanical Characteristics
• Case: Epoxy, Molded
• Weight: 0.4 gram (approximately)
• Finish: All External Surfaces Corrosion Resistant and Terminal
Leads are Readily Solderable
• Lead and Mounting Surface Temperature for Soldering Purposes:
•
•
•
•
220°C Max. for 10 Seconds, 1/16″ from case
Shipped in plastic bags, 1000 per bag
Available Tape and Reeled, 5000 per reel, by adding a “RL’’ suffix to
the part number
Polarity: Cathode Indicated by Polarity Band
Marking: MUR210
PLASTIC
AXIAL LEAD
CASE 059
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
VRRM
VRWM
VR
100
—
Volts
Average Rectified Forward Current
(Square Wave Mounting Method #3
Per Note 1.)
IF(AV)
2.0 @
TA = 100°C
Amps
Non-Repetitive Peak Surge Current
(Surge applied at rated load conditions,
halfwave, single phase, 60 Hz)
IFSM
35
Amps
TJ, Tstg
–65 to
+175
Operating Junction Temperature and
Storage Temperature Range
MARKING DIAGRAM
MUR210
MUR210 = Device Code
ORDERING INFORMATION
°C
1. Pulse Test: Pulse Width = 300 µs, Duty Cycle ≤ 2.0%.
Device
Package
Shipping
MUR210
Axial Lead
1000 Units/Bag
MUR210RL
Axial Lead
5000/Tape & Reel
Preferred devices are recommended choices for future use
and best overall value.
 Semiconductor Components Industries, LLC, 2000
September, 2000 – Rev. 0
1
Publication Order Number:
MUR210/D
MUR210
THERMAL CHARACTERISTICS
Characteristic
Maximum Thermal Resistance, Junction to Ambient
Symbol
Value
Unit
RθJA
See Note 3.
°C/W
ELECTRICAL CHARACTERISTICS
Maximum Instantaneous Forward Voltage (Note 2.)
(IF = 2.0 Amp, TJ = 150°C)
(IF = 2.0 Amp, TJ = 25°C)
VF
Maximum Instantaneous Reverse Current (Note 2.)
(Rated dc Voltage, TJ = 150°C)
(Rated dc Voltage, TJ = 25°C)
iR
Maximum Reverse Recovery Time
(IF = 1.0 Amp, di/dt = 50 Amp/µs)
(IF = 0.5 Amp, IR = 1.0 Amp, IREC = 0.25 A)
trr
Maximum Forward Recovery Time
(IF = 1.0 A, di/dt = 100 A/µs, IREC to 1.0 V)
tfr
Volts
0.74
0.94
µA
50
2.0
ns
30
20
20
ns
2. Pulse Test: Pulse Width = 300 µs, Duty Cycle ≤ 2.0%.
10
IF, INSTANTANEOUS FORWARD CURRENT (AMPS)
IF, INSTANTANEOUS FORWARD CURRENT (AMPS)
10
1
VF @ 175°C
VF @ 25°C
VF @ 100°C
0.1
0.3
0.5
0.7
0.9
1.1
1
0.1
0.3
1.3
VF @ 175°C
VF @ 25°C
VF @ 100°C
0.5
0.7
0.9
1.1
VF, INSTANTANEOUS VOLTAGE (VOLTS)
VF, INSTANTANEOUS VOLTAGE (VOLTS)
Figure 1. Maximum Forward Voltage
Figure 2. Typical Forward Voltage
http://onsemi.com
2
1.3
MUR210
100.000
IR, REVERSE CURRENT (µA)
IR, REVERSE CURRENT (µA)
1000
Ir @ 175°C
Ir @ 100°C
10
Ir @ 25°C
1
0.1
1.000
Ir @ 100°C
0.100
Ir @ 25°C
0.010
0.001
0
25
50
75
100
PF(AV), AVERAGE POWER DISSIPATION
(WATTS)
TJ = 175°C
Square Wave
1
0
100
50
150
200
100
2.5
TJ = 175°C
2.0
1.5
Square Wave
dc
1.0
0.5
0.0
0.0
0.5
1.0
1.5
2.0
2.5
TA, AMBIENT TEMPERATURE (°C)
IF(AV), AVERAGE FORWARD CURRENT
Figure 5. Current Derating
Figure 6. Power Dissipation
50
3.0
50
TJ = 25°C
TJ = 25°C
40
C, CAPACITANCE (pF)
C, CAPACITANCE (pF)
75
Figure 4. Typical Reverse Current
3
30
20
10
0
50
Figure 3. Maximum Reverse Current
dc
0
25
VR, REVERSE VOLTAGE (VOLTS)
4
2
0
VR, REVERSE VOLTAGE (VOLTS)
5
IF(AV), AVERAGE FORWARD
Ir @ 175°C
10.000
100
0
10
20
30
40
40
30
20
10
0
50
0
10
20
30
40
VR, REVERSE VOLTAGE (VOLTS)
VR, REVERSE VOLTAGE (VOLTS)
Figure 7. Maximum Capacitance
Figure 8. Typical Capacitance
http://onsemi.com
3
50
MUR210
NOTE 3. – AMBIENT MOUNTING DATA
Data shown for thermal resistance junction to
ambient (RθJA) for the mountings shown is to be
used as typical guideline values for preliminary
engineering or in case the tie point temperature
cannot be measured.
TYPICAL VALUES FOR RθJA IN STILL AIR
Mounting
Method
1
2
RθJA
Lead Length, L
1/8
1/4
1/2
52
65
72
67
80
87
Units
°C/W
°C/W
50
°C/W
3
MOUNTING METHOD 1
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
L
L
MOUNTING METHOD 2
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
L
L
Vector Pin Mounting
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
MOUNTING METHOD 3
L = 3/8 ″
Board Ground Plane
P.C. Board with
1–1/2 ″ X 1–1/2 ″ Copper Surface
http://onsemi.com
4
MUR210
PACKAGE DIMENSIONS
AXIAL LEAD
PLASTIC
CASE 59–04
ISSUE M
B
K
D
NOTES:
1. ALL RULES AND NOTES ASSOCIATED WITH
JEDEC DO-41 OUTLINE SHALL APPLY.
2. POLARITY DENOTED BY CATHODE BAND.
3. LEAD DIAMETER NOT CONTROLLED WITHIN F
DIMENSION.
DIM
A
B
D
K
A
MILLIMETERS
MIN
MAX
5.97
6.60
2.79
3.05
0.76
0.86
27.94
---
K
http://onsemi.com
5
INCHES
MIN
MAX
0.235
0.260
0.110
0.120
0.030
0.034
1.100
---
MUR210
Notes
http://onsemi.com
6
MUR210
Notes
http://onsemi.com
7
MUR210
SWITCHMODE is a trademark of Semiconductor Components Industries, LLC.
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
NORTH AMERICA Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
Fax Response Line: 303–675–2167 or 800–344–3810 Toll Free USA/Canada
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
CENTRAL/SOUTH AMERICA:
Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST)
Email: ONlit–[email protected]
ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support
Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)
Toll Free from Hong Kong & Singapore:
001–800–4422–3781
Email: ONlit–[email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: [email protected]
EUROPE: LDC for ON Semiconductor – European Support
German Phone: (+1) 303–308–7140 (Mon–Fri 2:30pm to 7:00pm CET)
Email: ONlit–[email protected]
French Phone: (+1) 303–308–7141 (Mon–Fri 2:00pm to 7:00pm CET)
Email: ONlit–[email protected]
English Phone: (+1) 303–308–7142 (Mon–Fri 12:00pm to 5:00pm GMT)
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781
*Available from Germany, France, Italy, UK, Ireland
For additional information, please contact your local
Sales Representative.
http://onsemi.com
8
MUR210/D
Similar pages