ON LM2902D Single supply quad operational amplifier Datasheet

LM324, LM324A, LM224,
LM2902, LM2902V, NCV2902
Single Supply Quad
Operational Amplifiers
The LM324 series are low–cost, quad operational amplifiers with
true differential inputs. They have several distinct advantages over
standard operational amplifier types in single supply applications. The
quad amplifier can operate at supply voltages as low as 3.0 V or as
high as 32 V with quiescent currents about one–fifth of those
associated with the MC1741 (on a per amplifier basis). The common
mode input range includes the negative supply, thereby eliminating the
necessity for external biasing components in many applications. The
output voltage range also includes the negative power supply voltage.
• Short Circuited Protected Outputs
• True Differential Input Stage
• Single Supply Operation: 3.0 V to 32 V (LM224, LM324, LM324A)
• Low Input Bias Currents: 100 nA Maximum (LM324A)
• Four Amplifiers Per Package
• Internally Compensated
• Common Mode Range Extends to Negative Supply
• Industry Standard Pinouts
• ESD Clamps on the Inputs Increase Ruggedness without Affecting
Device Operation
http://onsemi.com
PDIP–14
N SUFFIX
CASE 646
14
1
SO–14
D SUFFIX
CASE 751A
14
1
TSSOP–14
DTB SUFFIX
CASE 948G
14
1
MAXIMUM RATINGS (TA = +25°C, unless otherwise noted.)
Rating
Symbol
LM224
LM324,
LM324A
Power Supply Voltages
Single Supply
Split Supplies
VCC
VCC, VEE
32
±16
26
±13
Input Differential Voltage
Range (Note 1)
VIDR
±32
±26
Input Common Mode
Voltage Range
VICR
Output Short Circuit
Duration
tSC
Continuous
Junction Temperature
TJ
150
°C
Storage Temperature
Range
Tstg
–65 to +150
°C
Operating Ambient
Temperature Range
LM224
LM324, 324A
LM2902
LM2902V, NCV2902
TA
LM2902,
LM2902V
PIN CONNECTIONS
Unit
Vdc
Out 1
Inputs 1
Vdc
VCC
–0.3 to 32
–0.3 to 26
Vdc
Inputs 2
Out 2
1
14
2
13
3
1
4
11
4
5
6
12
2
3
10
9
8
7
Out 4
Inputs 4
VEE, Gnd
Inputs 3
Out 3
(Top View)
ORDERING INFORMATION
°C
–25 to +85
0 to +70
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
DEVICE MARKING INFORMATION
–40 to +105
–40 to +125
See general marking information in the device marking
section on page 10 of this data sheet.
1. Split Power Supplies.
 Semiconductor Components Industries, LLC, 2002
May, 2002 – Rev. 8
1
Publication Order Number:
LM324/D
LM324, LM324A, LM224, LM2902, LM2902V, NCV2902
ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = Gnd, TA = 25°C, unless otherwise noted.)
LM224
Characteristics
Symbol
Input Offset Voltage
VCC = 5.0 V to 30 V
(26 V for LM2902, V),
VICR = 0 V to
VCC –1.7 V,
VO = 1.4 V, RS = 0 Ω
VIO
Min
Typ
LM324A
Max
Min
Typ
LM324
Max
Min
Typ
LM2902
Max
Min
Typ
LM2902V/NCV2902
Max
Min
Typ
Max
Unit
mV
TA = 25°C
–
2.0
5.0
–
2.0
3.0
–
2.0
7.0
–
2.0
7.0
–
2.0
7.0
TA = Thigh (Note 2)
–
–
7.0
–
–
5.0
–
–
9.0
–
–
10
–
–
13
TA = Tlow (Note 2)
–
–
7.0
–
–
5.0
–
–
9.0
–
–
10
–
–
10
∆VIO/∆T
–
7.0
–
–
7.0
30
–
7.0
–
–
7.0
–
–
7.0
–
µV/°C
Input Offset Current
TA = Thigh to Tlow
(Note 2)
IIO
–
–
3.0
–
30
100
–
–
5.0
–
30
75
–
–
5.0
–
50
150
–
–
5.0
–
50
200
–
–
5.0
–
50
200
nA
Average Temperature
Coefficient of Input
Offset Current
TA = Thigh to Tlow
(Notes 2 and 4)
∆IIO/∆T
–
10
–
–
10
300
–
10
–
–
10
–
–
10
–
pA/°C
IIB
–
–
–90
–
–150
–300
–
–
–45
–
–100
–200
–
–
–90
–
–250
–500
–
–
–90
–
–250
–500
–
–
–90
–
–250
–500
nA
Average Temperature
Coefficient of Input
Offset Voltage
TA = Thigh to Tlow
(Notes 2 and 4)
Input Bias Current
TA = Thigh to Tlow
(Note 2)
Input Common Mode
Voltage Range
(Note 3)
VCC = 30 V
(26 V for LM2902, V)
VICR
V
TA = +25°C
0
–
28.3
0
–
28.3
0
–
28.3
0
–
24.3
0
–
24.3
TA = Thigh to Tlow
(Note 2)
0
–
28
0
–
28
0
–
28
0
–
24
0
–
24
–
–
VCC
–
–
VCC
–
–
VCC
–
–
VCC
–
–
VCC
Differential Input
Voltage Range
VIDR
Large Signal Open
Loop Voltage Gain
RL = 2.0 kΩ,
VCC = 15 V,
for Large VO Swing
AVOL
V
V/mV
50
100
–
25
100
–
25
100
–
25
100
–
25
100
–
25
–
–
15
–
–
15
–
–
15
–
–
15
–
–
CS
–
–120
–
–
–120
–
–
–120
–
–
–120
–
–
–120
–
dB
Common Mode
Rejection,
RS ≤ 10 kΩ
CMR
70
85
–
65
70
–
65
70
–
50
70
–
50
70
–
dB
Power Supply
Rejection
PSR
65
100
–
65
100
–
65
100
–
50
100
–
50
100
–
dB
TA = Thigh to Tlow
(Note 2)
Channel Separation
10 kHz ≤ f ≤ 20 kHz,
Input Referenced
2. LM224: Tlow = –25°C, Thigh = +85°C
LM324/LM324A: Tlow = 0°C, Thigh = +70°C
LM2902: Tlow = –40°C, Thigh = +105°C
LM2902V & NCV2902: Tlow = –40°C, Thigh = +125°C
NCV2902 is qualified for automotive use.
3. The input common mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of
the common mode voltage range is VCC –1.7 V.
4. Guaranteed by design.
http://onsemi.com
2
LM324, LM324A, LM224, LM2902, LM2902V, NCV2902
ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = Gnd, TA = 25°C, unless otherwise noted.)
LM224
Characteristics
Output Voltage–
High Limit
(TA = Thigh to Tlow)
(Note 5)
VCC = 5.0 V, RL =
2.0 kΩ, TA = 25°C
Symbol
Min
Typ
LM324A
Max
Min
Typ
LM324
Max
Min
Typ
LM2902
Max
Min
Typ
LM2902V/NCV2902
Max
Min
Typ
Max
VOH
V
3.3
3.5
–
3.3
3.5
–
3.3
3.5
–
3.3
3.5
–
3.3
3.5
–
VCC = 30 V
(26 V for LM2902, V),
RL = 2.0 kΩ
26
–
–
26
–
–
26
–
–
22
–
–
22
–
–
VCC = 30 V
(26 V for LM2902, V),
RL = 10 kΩ
27
28
–
27
28
–
27
28
–
23
24
–
23
24
–
–
5.0
20
–
5.0
20
–
5.0
20
–
5.0
100
–
5.0
100
Output Voltage –
Low Limit,
VCC = 5.0 V,
RL = 10 kΩ,
TA = Thigh to Tlow
(Note 5)
VOL
Output Source Current
(VID = +1.0 V,
VCC = 15 V)
TA = 25°C
IO +
Unit
mV
mA
20
40
–
20
40
–
20
40
–
20
40
–
20
40
–
10
20
–
10
20
–
10
20
–
10
20
–
10
20
–
10
20
–
10
20
–
10
20
–
10
20
–
10
20
–
TA = Thigh to Tlow
(Note 5)
5.0
8.0
–
5.0
8.0
–
5.0
8.0
–
5.0
8.0
–
5.0
8.0
–
(VID = –1.0 V,
VO = 200 mV,
TA = 25°C)
12
50
–
12
50
–
12
50
–
–
–
–
–
–
–
µA
–
40
60
–
40
60
–
40
60
–
40
60
–
40
60
mA
TA = Thigh to Tlow
(Note 5)
Output Sink Current
(VID = –1.0 V,
VCC = 15 V)
TA = 25°C
IO –
Output Short Circuit
to Ground
(Note 6)
ISC
Power Supply Current
(TA = Thigh to Tlow)
(Note 5)
VCC = 30 V
(26 V for LM2902, V),
VO = 0 V, RL = ∞
ICC
VCC = 5.0 V,
VO = 0 V, RL = ∞
mA
mA
–
–
3.0
–
1.4
3.0
–
–
3.0
–
–
3.0
–
–
3.0
–
–
1.2
–
0.7
1.2
–
–
1.2
–
–
1.2
–
–
1.2
5. LM224: Tlow = –25°C, Thigh = +85°C
LM324/LM324A: Tlow = 0°C, Thigh = +70°C
LM2902: Tlow = –40°C, Thigh = +105°C
LM2902V & NCV2902: Tlow = –40°C, Thigh = +125°C
NCV2902 is qualified for automotive use.
6. The input common mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of
the common mode voltage range is VCC –1.7 V.
http://onsemi.com
3
LM324, LM324A, LM224, LM2902, LM2902V, NCV2902
Output
Bias Circuitry
Common to Four
Amplifiers
VCC
Q15
Q16
Q22
Q14
Q13
40 k
Q19
5.0 pF
Q12
Q24
25
Q23
+
Q20
Q18
Inputs
-
Q21
Q17
Q2
Q5
Q3
Q4
Q11
Q9
Q6
Q26
Q25
Q7
Q8
Q10
Q1
2.4 k
2.0 k
VEE/Gnd
Figure 1. Representative Circuit Diagram
(One–Fourth of Circuit Shown)
http://onsemi.com
4
LM324, LM324A, LM224, LM2902, LM2902V, NCV2902
CIRCUIT DESCRIPTION
The LM324 series is made using four internally
compensated, two–stage operational amplifiers. The first
stage of each consists of differential input devices Q20 and
Q18 with input buffer transistors Q21 and Q17 and the
differential to single ended converter Q3 and Q4. The first
stage performs not only the first stage gain function but also
performs the level shifting and transconductance reduction
functions. By reducing the transconductance, a smaller
compensation capacitor (only 5.0 pF) can be employed, thus
saving chip area. The transconductance reduction is
accomplished by splitting the collectors of Q20 and Q18.
Another feature of this input stage is that the input common
mode range can include the negative supply or ground, in
single supply operation, without saturating either the input
devices or the differential to single–ended converter. The
second stage consists of a standard current source load
amplifier stage.
3.0 V to VCC(max)
1.0 V/DIV
VCC = 15 Vdc
RL = 2.0 kΩ
TA = 25°C
5.0 µs/DIV
Figure 2. Large Signal Voltage Follower Response
Each amplifier is biased from an internal–voltage
regulator which has a low temperature coefficient thus
giving each amplifier good temperature characteristics as
well as excellent power supply rejection.
VCC
VCC
1
1
1.5 V to VCC(max)
2
2
3
3
4
4
1.5 V to VEE(max)
VEE
VEE/Gnd
Single Supply
Split Supplies
Figure 3.
http://onsemi.com
5
LM324, LM324A, LM224, LM2902, LM2902V, NCV2902
20
120
A VOL, LARGE-SIGNAL
OPEN LOOP VOLTAGE GAIN (dB)
± V , INPUT VOLTAGE (V)
I
18
16
14
12
10
Negative
8.0
Positive
6.0
4.0
2.0
0
0
2.0
4.0
6.0
8.0
10
12
14
16
18
80
60
40
20
0
-20
20
1.0
10
100
1.0 k
10 k
100 k
± VCC/VEE, POWER SUPPLY VOLTAGES (V)
f, FREQUENCY (Hz)
Figure 4. Input Voltage Range
Figure 5. Open Loop Frequency
14
1.0 M
550
RL = 2.0 kΩ
VCC = 15 V
VEE = Gnd
Gain = -100
RI = 1.0 kΩ
RF = 100 kΩ
12
10
8.0
VO , OUTPUT VOLTAGE (mV)
VOR , OUTPUT VOLTAGE RANGE (Vpp )
VCC = 15 V
VEE = Gnd
TA = 25°C
100
6.0
4.0
2.0
500
Input
450
Output
400
350
300
250
VCC = 30 V
VEE = Gnd
TA = 25°C
CL = 50 pF
200
0
1.0
10
100
0
1000
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
f, FREQUENCY (kHz)
t, TIME (µs)
Figure 6. Large–Signal Frequency Response
Figure 7. Small–Signal Voltage Follower
Pulse Response (Noninverting)
8.0
TA = 25°C
RL = 2.1
1.8
I IB , INPUT BIAS CURRENT (nA)
I CC , POWER SUPPLY CURRENT (mA)
2.4
1.5
1.2
0.9
0.6
0.3
0
0
5.0
10
15
20
25
VCC, POWER SUPPLY VOLTAGE (V)
30
90
80
70
35
0
Figure 8. Power Supply Current versus
Power Supply Voltage
2.0
4.0
6.0 8.0
10
12
14 16
VCC, POWER SUPPLY VOLTAGE (V)
Figure 9. Input Bias Current versus
Power Supply Voltage
http://onsemi.com
6
18
20
LM324, LM324A, LM224, LM2902, LM2902V, NCV2902
50 k
R1
VCC
R2
MC1403
5.0 k
VCC
-
2.5 V
10 k
Vref
1/4
Vref =
R
R1
R2
a R1
e2
Vref
1/4
eo
VOH
R1
+
VO
1/4
LM324
-
Vin
1
CR
LM324
+
VinH =
R
-
100 k
C
C
R
1/4
LM324
+
-
100 k
1/4
-
LM324
+
Vref
R1
VinH
Vref
Figure 13. Comparator with Hysteresis
R
R2
VinL
R1
(VOH - VOL)
R1 + R2
R
R2
VOL
R1
(VOH - Vref) + Vref
R1 + R2
H=
Figure 12. High Impedance Differential Amplifier
C1
VO
R1
(VOL - Vref) + Vref
VinL =
R1 + R2
eo = C (1 + a + b) (e2 - e1)
Vin
For: fo = 1.0 kHz
R = 16 kΩ
C = 0.01 µF
Hysteresis
LM324
+
1/4
C
R
-
b R1
C
R
Figure 11. Wien Bridge Oscillator
LM324
R1
1
fo = 2 π RC
R2
1
CR
1/4
VO
1
V
2 CC
Figure 10. Voltage Reference
+
VCC
1/4
LM324
+
VO
LM324
+
VO = 2.5 V 1 +
e1
-
LM324
+
Vref
Bandpass
Output
R3
-
Vref
Vref =
1
V
2 CC
R3 = TN R2
C1 = 10C
For:fo=1.0 kHz
For:Q= 10
For:TBP= 1
For:TN= 1
Notch Output
Where:TBP=Center Frequency Gain
Where:TN=Passband Notch Gain
Figure 14. Bi–Quad Filter
http://onsemi.com
Vref
R1 = QR
R1
R2 =
TBP
C1
1/4
LM324
+
7
1/4
1
fo = 2 π RC
R
C
R1
R2
R3
= 160 kΩ
= 0.001 µF
= 1.6 MΩ
= 1.6 MΩ
= 1.6 MΩ
LM324, LM324A, LM224, LM2902, LM2902V, NCV2902
Vref =
Vref
1
V
2 CC
Triangle Wave
Output
+
R2
300 k
R3
1/4
LM324
-
+
75 k
VCC
1/4
LM324
-
R1
100 k
Vref
C
Square
Wave
Output
Vin
R1
R1 + RC
4 CRf R1
C
R3
-
if R3 =
Vref
R2 R1
R2 + R1
Figure 15. Function Generator
CO
1/4
VO
LM324
+
R2
Rf
f =
C
CO = 10 C
1
Vref = 2 VCC
Figure 16. Multiple Feedback Bandpass Filter
Given:fo=center frequency
A(fo)=gain at center frequency
Choose value fo, C
Then:
R3 =
Q
π fo C
R1 =
R3
2 A(fo)
R2 =
R1 R3
4Q2 R1 - R3
For less than 10% error from operational amplifier,
Qo fo
BW
where fo and BW are expressed in Hz.
If source impedance varies, filter may be preceded with
voltage follower buffer to stabilize filter parameters.
http://onsemi.com
8
< 0.1
LM324, LM324A, LM224, LM2902, LM2902V, NCV2902
ORDERING INFORMATION
Device
LM224D
Package
Operating Temperature Range
SO–14
Shipping
55 Units/Rail
LM224DR2
SO–14
LM224DTB
TSSOP–14
LM224DTBR2
TSSOP–14
2500 Tape & Reel
LM224N
PDIP–14
25 Units/Rail
LM324D
SO–14
55 Units/Rail
LM324DR2
SO–14
2500 Tape & Reel
LM324DTB
TSSOP–14
96 Units/Rail
LM324DTBR2
TSSOP–14
2500 Tape & Reel
LM324N
2500 Tape & Reel
–25°
5 to
o +85°C
85 C
PDIP–14
0° to +70°C
96 Units/Rail
25 Units/Rail
LM324AD
SO–14
LM324ADR2
SO–14
LM324ADTB
TSSOP–14
96 Units/Rail
LM324ADTBR2
TSSOP–14
2500 Tape & Reel
LM324AN
PDIP–14
25 Units/Rail
LM2902D
SO–14
55 Units/Rail
LM2902DR2
SO–14
2500 Tape & Reel
LM2902DTB
TSSOP–14
LM2902DTBR2
TSSOP–14
2500 Tape & Reel
PDIP–14
25 Units/Rail
LM2902N
55 Units/Rail
2500 Tape & Reel
–40°
0 to
o +105°C
05 C
96 Units/Rail
LM2902VD
SO–14
55 Units/Rail
LM2902VDR2
SO–14
2500 Tape & Reel
LM2902VDTB
TSSOP–14
LM2902VDTBR2
TSSOP–14
LM2902VN
NCV2902DR2
–40°
40° to +125°C
96 Units/Rail
2500 Tape & Reel
PDIP–14
25 Units/Rail
SO–14
2500 Tape & Reel
http://onsemi.com
9
LM324, LM324A, LM224, LM2902, LM2902V, NCV2902
MARKING DIAGRAMS
PDIP–14
N SUFFIX
CASE 646
14
14
14
LM324AN
AWLYYWW
1
14
LMx24N
AWLYYWW
LM2902N
AWLYYWW
1
LM2902VN
AWLYYWW
1
1
SO–14
D SUFFIX
CASE 751A
14
14
LM324AD
AWLYWW
1
14
LMx24D
AWLYWW
14
LM2902D
AWLYWW
1
LM2902VD
AWLYWW
1
1
TSSOP–14
DTB SUFFIX
CASE 948G
14
14
1
14
14
x24
324A
2902
AWYW
AWYW
AWYW
1
1
2902
V
AWYW
1
x
= 2 or 3
A
= Assembly Location
WL
= Wafer Lot
YY, Y = Year
WW, W = Work Week
*This marking diagram also applies to NCV2902.
http://onsemi.com
10
*
LM324, LM324A, LM224, LM2902, LM2902V, NCV2902
PACKAGE DIMENSIONS
PDIP–14
N SUFFIX
CASE 646–06
ISSUE M
14
8
1
7
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
B
A
F
DIM
A
B
C
D
F
G
H
J
K
L
M
N
L
N
C
–T–
SEATING
PLANE
J
K
H
D 14 PL
G
M
0.13 (0.005)
INCHES
MIN
MAX
0.715
0.770
0.240
0.260
0.145
0.185
0.015
0.021
0.040
0.070
0.100 BSC
0.052
0.095
0.008
0.015
0.115
0.135
0.290
0.310
--10
0.015
0.039
MILLIMETERS
MIN
MAX
18.16
18.80
6.10
6.60
3.69
4.69
0.38
0.53
1.02
1.78
2.54 BSC
1.32
2.41
0.20
0.38
2.92
3.43
7.37
7.87
--10
0.38
1.01
M
SO–14
D SUFFIX
CASE 751A–03
ISSUE F
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
–A–
14
8
–B–
1
P 7 PL
0.25 (0.010)
7
G
B
M
M
F
R X 45 C
–T–
SEATING
PLANE
D 14 PL
0.25 (0.010)
M
K
M
T B
S
A
S
http://onsemi.com
11
J
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
8.55
8.75
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0
7
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.337
0.344
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0
7
0.228
0.244
0.010
0.019
LM324, LM324A, LM224, LM2902, LM2902V, NCV2902
PACKAGE DIMENSIONS
TSSOP–14
DTB SUFFIX
CASE 948G–01
ISSUE O
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH
OR GATE BURRS SHALL NOT EXCEED 0.15
(0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED
0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN
EXCESS OF THE K DIMENSION AT MAXIMUM
MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE DETERMINED
AT DATUM PLANE -W-.
14X K REF
0.10 (0.004)
0.15 (0.006) T U
M
T U
V
S
S
S
N
2X
14
L/2
0.25 (0.010)
8
M
B
–U–
L
PIN 1
IDENT.
F
7
1
0.15 (0.006) T U
N
S
DETAIL E
K
A
–V–
ÇÇÇ
ÉÉ
ÇÇÇ
ÉÉ
K1
J J1
SECTION N–N
–W–
C
0.10 (0.004)
–T– SEATING
PLANE
D
G
H
DETAIL E
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
--1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.50
0.60
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0
8
INCHES
MIN
MAX
0.193
0.200
0.169
0.177
--0.047
0.002
0.006
0.020
0.030
0.026 BSC
0.020
0.024
0.004
0.008
0.004
0.006
0.007
0.012
0.007
0.010
0.252 BSC
0
8
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make
changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all
liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
http://onsemi.com
12
LM324/D