DATA SHORT To request the full datasheet, please visit: ISL79985 or ISL79986 4-Channel Differential Input Video Decoder with MIPI-CSI2/BT.656 Output for Around View Applications ISL79985, ISL79986 Features The ISL79985, ISL79986 integrates four high quality NTSC/PAL/SECAM video decoders that convert the analog composite video signal to digital component YCbCr data for automotive applications. Each channel contains a 10-bit ADC that supports single-ended, differential, and pseudo differential composite video inputs, proprietary clamp and gain controllers, thus, utilizes a 4H-comb filter for separating luminance and chrominance to reduce cross noise artifacts. Integrated short-to-battery and short-to-ground detection, advanced image enhancement capabilities such as the programmable Automatic Contrast Adjustment (ACA), and the MIPI-CSI2/ITU-R BT.656 output interface make the ISL79985, ISL79986 an ideal solution for demanding automotive around view applications. Analog Video Decoder Applications • Digital horizontal PLL for synchronization processing and pixel sampling • Software selectable analog input control allows for combinations of single-ended CVBS and differential CVBS • Integrated four video analog anti-aliasing filters and 10-bit CMOS ADCs with differential and single-ended inputs • Fully programmable static gain or automatic gain control for the Y-channel • Programmable white peak control for the Y-channel • 4-H adaptive comb filter Y/C separation • PAL delay line for color phase error correction • Digital subcarrier PLL for accurate color decoding • Automotive surround view • Advanced synchronization processing and sync detection for handling non-standard and weak signal • Automatic color control and color killer • Chroma IF compensation • Programmable output cropping AFE CLKO/ MPP[1] CSC CSC ADC AGC ACA AA FILTER 4H COMB VIDEO DE C ACA VIN1A MPP[0] VIN1B DEC_CH REGFILE DIAG1 AA FILTER 4H COMB VIDEO DE C ADC AGC VIN4A VIN4B AA FILTER DEC_CH DIAG4 PLL OSC XTO XTI PD SHORT DETECTION MIP ID1 REGFILE I2C INTE RFACE SCLK RSTB MIP ID0 REGFILE 4H COMB VIDEO DE C ADC AGC MIP IC REGFILE IRQ DEC_CH DIAG3 CSC 4H COMB VIDEO DE C ADC AGC CSC AA FILTER ACA VIN3B ACA VIN3A SDAT DEC_CH DIAG2 REGFILE MIP I CSI AND DPHY VIN2B FIFO CONTROL LINE INTERLEAVING ENGINE VIN2A FIGURE 1. ISL79985 BLOCK DIAGRAM June 24, 2016 FN8851.2 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2016. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. ISL79985, ISL79986 Features (Continued) Video Processing Miscellaneous • Automatic Contrast Adjustment (ACA) • Low power consumption • Programmable hue, brightness, saturation, contrast and sharpness. • Power save and power-down mode • Image enhancement with peaking and CTI • Short-to-ground detection MIPI Output (ISL79985) • 2-wire MPU serial bus interface • MIPI CSI-2 Version 1.1 compliant unidirectional output format • Single 27MHz crystal for all operations • Standard virtual channel support • 1.2V/3.3 V power supply • One or two data lanes • 48 Ld QFN package • YUV422 or RGB565 output format • AEC-Q100 qualified • Short-to-battery detection Digital Output (ISL79986) • Supports standard ITU-R BT.656 format or time multiplexed output with 27/54/108MHz • Output voltage 1.8V to 3.3V AFE CLKO/ MPP[1] AA FILTER ADC AGC DEC_CH MPP[0] CSC VIN1B 4H COMB VIDEO DEC ACA VIN1A REGFILE DIAG1 4H COMB VIDEO DEC DEC_CH DIAG3 AA FILTER 4H COMB VIDEO DEC ADC AGC DEC_CH DIAG4 RSTB XTO XTI SHORT DETECTION REGFILE I2C INTERFACE SCLK PLL OSC PD CSC VIN4B REGFILE ACA VIN4A VD[7:0] REGFILE IRQ ADC AGC SDAT AA FILTER CSC VIN3B ACA VIN3A REGFILE BT 656 DEC_CH DIAG2 FIFO CONTROL 4H COMB VIDEO DEC ADC AGC LINE INTERLEAVING ENGINE AA FILTER CSC VIN2B ACA VIN2A FIGURE 2. ISL79986 BLOCK DIAGRAM For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 or TS16949 quality systems as applicable noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com Submit Document Feedback 2 FN8851.2 June 24, 2016