CAT24AA01, CAT24AA02 1-Kb and 2-Kb I2C CMOS Serial EEPROM Description The CAT24AA01/24AA02 are 1−Kb and 2−Kb CMOS Serial EEPROM devices internally organized as 128x8/256x8 bits. They feature a 16−byte page write buffer and support the Standard (100 kHz), Fast (400 kHz) and Fast−Plus (1 MHz) I2C protocols. In contrast to the CAT24C01/24C02, the CAT24AA01/24AA02 have no external address pins, and are therefore suitable in applications that require a single CAT24AA01/02 on the I 2C bus. www.onsemi.com TSOT−23 TD SUFFIX CASE 419AE Features • • • • • • • • • • Supports Standard, Fast and Fast−Plus I2C Protocol 1.7 V to 5.5 V Supply Voltage Range 16−Byte Page Write Buffer Hardware Write Protection for Entire Memory Schmitt Triggers and Noise Suppression Filters on I2C Bus Inputs (SCL and SDA) Low Power CMOS Technology 1,000,000 Program/Erase Cycles 100 Year Data Retention Industrial Temperature Range These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS Compliant PIN CONFIGURATIONS TSOT−23 SCL 1 VSS 2 SDA 3 5 WP 4 VCC (Top View) MARKING DIAGRAM VCC RSYM SCL CAT24AA01 CAT24AA02 SDA RS = Device Code Y = Production Year (Last Digit) M = Production Month (1−9, O, N, D) WP VSS PIN FUNCTION Figure 1. Functional Symbol Pin Name Function SDA Serial Data/Address SCL Clock Input WP Write Protect VCC Power Supply VSS Ground ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 10 of this data sheet. © Semiconductor Components Industries, LLC, 2015 May, 2015 − Rev. 5 1 Publication Order Number: CAT24AA01/D CAT24AA01, CAT24AA02 Table 1. ABSOLUTE MAXIMUM RATINGS Parameters Ratings Units Storage Temperature −65 to +150 °C Voltage on any Pin with Respect to Ground (Note 1) −0.5 to +6.5 V Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. The DC input voltage on any pin should not be lower than −0.5 V or higher than VCC + 0.5 V. During transitions, the voltage on any pin may undershoot to no less than −1.5 V or overshoot to no more than VCC + 1.5 V, for periods of less than 20 ns. Table 2. REABILITY CHARACTERISTICS (Note 2) Symbol NEND (Note 3) TDR Parameter Endurance Data Retention Min Units 1,000,000 Program/Erase Cycles 100 Years 2. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100 and JEDEC test methods. 3. Page Mode @ 25°C Table 3. D.C. OPERATING CHARACTERISTICS (VCC = 1.7 V to 5.5 V, TA = −40°C to 85°C, unless otherwise specified.) Symbol Parameter Test Conditions ICCR Read Current Read, fSCL = 400 kHz ICCW Min Max Units 0.5 mA Write Current Write 1 mA ISB Standby Current All I/O Pins at GND or VCC 1 mA IL I/O Pin Leakage Pin at GND or VCC 1 mA VIL Input Low Voltage −0.5 VCC x 0.3 V VIH Input High Voltage VCC x 0.7 VCC + 0.5 V VOL1 Output Low Voltage VCC ≥ 2.5 V, IOL = 3.0 mA 0.4 V VOL2 Output Low Voltage VCC < 2.5 V, IOL = 1.0 mA 0.2 V Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. Table 4. PIN IMPEDANCE CHARACTERISTICS (VCC = 1.7 V to 5.5 V, TA = −40°C to 85°C, unless otherwise specified.) Symbol Parameter Conditions Max Units CIN (Note 2) SDA I/O Pin Capacitance VIN = 0 V 8 pF CIN (Note 2) Input Capacitance (other pins) VIN = 0 V 6 pF IWP (Note 4) WP Input Current VIN < VIH 100 mA VIN > VIH 1 4. When not driven, the WP pin is pulled down to GND internally. For improved noise immunity, the internal pull−down is relatively strong; therefore the external driver must be able to supply the pull−down current when attempting to drive the input HIGH. To conserve power, as the input level exceeds the trip point of the CMOS input buffer (~ 0.5 x VCC), the strong pull−down reverts to a weak current source. www.onsemi.com 2 CAT24AA01, CAT24AA02 Table 5. A.C. CHARACTERISTICS (Note 5) (VCC = 1.7 V to 5.5 V, TA = −40°C to 85°C, unless otherwise specified.) FSCL tHD:STA Fast 1 MHz VCC = 1.7 V – 5.5 V VCC = 2.5 V – 5.5 V Min Parameter Symbol Standard VCC = 1.7 V – 5.5 V Clock Frequency Max Min 100 START Condition Hold Time Max Min 400 Max Units 1000 kHz 4 0.6 0.25 ms tLOW Low Period of SCL Clock 4.7 1.3 0.5 ms tHIGH High Period of SCL Clock 4 0.6 0.5 ms 4.7 0.6 0.25 ms 0 0 ns tSU:STA START Condition Setup Time tHD:DAT Data In Hold Time 0 tSU:DAT Data In Setup Time 250 tR (Note 6) SDA and SCL Rise Time 1000 300 300 ns tF (Note 6) SDA and SCL Fall Time 300 300 100 ns tSU:STO STOP Condition Setup Time tBUF Bus Free Time Between STOP and START tAA SCL Low to Data Out Valid tDH Data Out Hold Time Ti (Note 6) ns 0.6 0.25 ms 4.7 1.3 0.5 ms 3.5 100 Noise Pulse Filtered at SCL and SDA Inputs 0.9 50 100 WP Setup Time 0 tHD:WP WP Hold Time 2.5 tPU (Notes 6, 7) 100 4 tSU:WP tWR 100 0.4 50 100 0 ns 100 ns ms 0 2.5 ms ms 1 Write Cycle Time 5 5 5 ms Power−up to Ready Mode 1 1 1 ms 5. Test conditions according to “A.C. Test Conditions” table. 6. Tested initially and after a design or process change that affects this parameter. 7. tPU is the delay between the time VCC is stable and the device is ready to accept commands. Table 6. A.C. TEST CONDITIONS Input Levels 0.2 x VCC to 0.8 x VCC Input Rise and Fall Times ≤ 50 ns Input Reference Levels 0.3 x VCC, 0.7 x VCC Output Reference Levels 0.5 x VCC Output Load Current Source: IOL = 3 mA (VCC ≥ 2.5 V); IOL = 1 mA (VCC < 2.5 V); CL = 100 pF www.onsemi.com 3 CAT24AA01, CAT24AA02 I2C BUS PROTOCOL Power−On Reset (POR) Each CAT24AA01/02 incorporates Power−On Reset (POR) circuitry which protects the internal logic against powering up in the wrong state. The device will power up into Standby mode after VCC exceeds the POR trigger level and will power down into Reset mode when VCC drops below the POR trigger level. This bi−directional POR behavior protects the device against brown−out failure, following a temporary loss of power. The 2−wire I2C bus consists of two lines, SCL and SDA, connected to the VCC supply via pull−up resistors. The Master provides the clock to the SCL line, and the Master and Slaves drive the SDA line. A ‘0’ is transmitted by pulling a line LOW and a ‘1’ by releasing it HIGH. Data transfer may be initiated only when the bus is not busy (see A.C. Characteristics). During data transfer, SDA must remain stable while SCL is HIGH. START/STOP Condition An SDA transition while SCL is HIGH creates a START or STOP condition (Figure 2). A START is generated by a HIGH to LOW transition, while a STOP is generated by a LOW to HIGH transition. The START acts like a wake−up call. Absent a START, no Slave will respond to the Master. The STOP completes all commands. Pin Description SCL: The Serial Clock input pin accepts the clock signal generated by the Master. SDA: The Serial Data I/O pin accepts input data and delivers output data. In transmit mode, this pin is open drain. Data is acquired on the positive edge, and delivered on the negative edge of SCL. WP: When the Write Protect input pin is forced HIGH by an external source, all write operations are inhibited. When the pin is not driven by an external source, it is pulled LOW internally. Device Addressing The Master addresses a Slave by creating a START condition and then broadcasting an 8−bit Slave address (Figure 3). The four most significant bits of the Slave address are 1010 (Ah). For the CAT24AA01/02 the next three bits must be 000. The last bit, R/W, instructs the Slave to either provide (1) or accept (0) data, i.e. it signals a Read (1) or a Write (0) request. Functional Description The CAT24AA01/02 supports the Inter−Integrated Circuit (I2C) Bus protocol. The protocol relies on the use of a Master device, which provides the clock and directs bus traffic, and Slave devices which execute requests. The CAT24AA01/02 operates as a Slave device. Both Master and Slave can transmit or receive, but only the Master can assign those roles. Acknowledge During the 9th clock cycle following every byte sent onto the bus, the transmitter releases the SDA line, allowing the receiver to respond. The receiver then either acknowledges (ACK) by pulling SDA LOW, or does not acknowledge (NoACK) by letting SDA stay HIGH (Figure 4). Bus timing is illustrated in Figure 5. SCL SDA START CONDITION STOP CONDITION Figure 2. Start/Stop Timing 1 0 1 0 0 0 0 R/W Figure 3. Slave Address Bits www.onsemi.com 4 CAT24AA01, CAT24AA02 BUS RELEASE DELAY (TRANSMITTER) SCL FROM MASTER 1 BUS RELEASE DELAY (RECEIVER) 8 9 DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER START ACK SETUP (≥ tSU:DAT) ACK DELAY (≤ tAA) Figure 4. Acknowledge Timing tHIGH tF tLOW tR tLOW SCL tHD:DAT tSU:STA tHD:STA tSU:DAT tSU:STO SDA IN tAA tDH tBUF SDA OUT Figure 5. Bus Timing WRITE OPERATIONS Byte Write Acknowledge Polling To write data to memory, the Master creates a START condition on the bus and then broadcasts a Slave address with the R/W bit set to ‘0’. The Master then sends an address byte and a data byte and concludes the session by creating a STOP condition on the bus. The Slave responds with ACK after every byte sent by the Master (Figure 5). The STOP starts the internal Write cycle, and while this operation is in progress (tWR), the SDA output is tri−stated and the Slave does not acknowledge the Master (Figure 6). As soon (and as long) as internal Write is in progress, the Slave will not acknowledge the Master. This feature enables the Master to immediately follow−up with a new Read or Write request, rather than wait for the maximum specified Write time (tWR) to elapse. Upon receiving a NoACK response from the Slave, the Master simply repeats the request until the Slave responds with ACK. Hardware Write Protection With the WP pin held HIGH, the entire memory is protected against Write operations. If the WP pin is left floating or is grounded, it has no impact on the Write operation. The state of the WP pin is strobed on the last falling edge of SCL immediately preceding the 1st data byte (Figure 8). If the WP pin is HIGH during the strobe interval, the Slave will not acknowledge the data byte and the Write request will be rejected. Page Write The Byte Write operation can be expanded to Page Write, by sending more than one data byte to the Slave before issuing the STOP condition (Figure 7). Up to 16 distinct data bytes can be loaded into the internal Page Write Buffer starting at the address provided by the Master. The page address is latched, and as long as the Master keeps sending data, the internal byte address is incremented up to the end of page, where it then wraps around (within the page). New data can therefore replace data loaded earlier. Following the STOP, data loaded during the Page Write session will be written to memory in a single internal Write cycle (tWR). Delivery State The CAT24AA01/02 is shipped erased, i.e., all bytes are FFh. www.onsemi.com 5 CAT24AA01, CAT24AA02 BUS ACTIVITY: MASTER S T A R T SLAVE ADDRESS ADDRESS BYTE DATA BYTE a7 ÷ a 0 d7 ÷ d0 S T O P P S A C K SLAVE A C K A C K Figure 6. Byte Write Sequence SCL 8th Bit Byte n SDA ACK tWR STOP CONDITION START CONDITION ADDRESS Figure 7. Write Cycle Timing BUS ACTIVITY: S T A MASTER R T DATA BYTE n ADDRESS BYTE SLAVE ADDRESS DATA BYTE n+1 DATA BYTE n+x S T O P S P A C K SLAVE A C K A C K A C K n =1 x v15 Figure 8. Page Write Sequence ADDRESS BYTE DATA BYTE 1 8 a7 a0 9 1 8 d7 d0 SCL SDA tSU:WP WP tHD:WP Figure 9. WP Timing www.onsemi.com 6 A C K CAT24AA01, CAT24AA02 READ OPERATIONS Immediate Read condition and broadcasts a Slave address with the R/W bit set to ‘1’. The Slave responds with ACK after every byte sent by the Master and then sends out data residing at the selected address. After receiving the data, the Master responds with NoACK and then terminates the session by creating a STOP condition on the bus (Figure 11). To read data from memory, the Master creates a START condition on the bus and then broadcasts a Slave address with the R/W bit set to ‘1’. The Slave responds with ACK and starts shifting out data residing at the current address. After receiving the data, the Master responds with NoACK and terminates the session by creating a STOP condition on the bus (Figure 10). The Slave then returns to Standby mode. Sequential Read If, after receiving data sent by the Slave, the Master responds with ACK, then the Slave will continue transmitting until the Master responds with NoACK followed by STOP (Figure 12). During Sequential Read the internal byte address is automatically incremented up to the end of memory, where it then wraps around to the beginning of memory. For the CAT24AA01, the internal address counter will not wrap around at the end of the 128 byte memory space. Selective Read To read data residing at a specific address, the selected address must first be loaded into the internal address register. This is done by starting a Byte Write sequence, whereby the Master creates a START condition, then broadcasts a Slave address with the R/W bit set to ‘0’ and then sends an address byte to the Slave. Rather than completing the Byte Write sequence by sending data, the Master then creates a START BUS ACTIVITY: MASTER N O S T A R T S AT CO KP SLAVE ADDRESS P S A C K SLAVE 8 SCL DATA BYTE 9 8th Bit SDA DATA OUT NO ACK STOP Figure 10. Immediate Read Sequence and Timing S T A MASTER R T S T A R T BUS ACTIVITY: ADDRESS BYTE SLAVE ADDRESS S N O S AT CO KP SLAVE ADDRESS P S A C K SLAVE A C K A C K DATA BYTE Figure 11. Selective Read Sequence N O BUS ACTIVITY: MASTER A C K SLAVE ADDRESS A C K S A T CO K P A C K P SLAVE A C K DATA BYTE n DATA BYTE n+1 DATE BYTA n+2 Figure 12. Sequential Read Sequence www.onsemi.com 7 DATA BYTE n+x CAT24AA01, CAT24AA02 PACKAGE DIMENSIONS SOIC 8, 150 mils CASE 751BD−01 ISSUE O E1 E SYMBOL MIN A 1.35 1.75 A1 0.10 0.25 b 0.33 0.51 MAX c 0.19 0.25 D 4.80 5.00 E 5.80 6.20 E1 3.80 4.00 1.27 BSC e PIN # 1 IDENTIFICATION NOM h 0.25 0.50 L 0.40 1.27 θ 0º 8º TOP VIEW D h A1 θ A c e b L END VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-012. www.onsemi.com 8 CAT24AA01, CAT24AA02 PACKAGE DIMENSIONS TSOT−23, 5 LEAD CASE 419AE−01 ISSUE O SYMBOL D MIN NOM A e E1 MAX 1.00 A1 0.01 0.05 0.10 A2 0.80 0.87 0.90 b 0.30 c 0.12 E 0.45 0.15 D 2.90 BSC E 2.80 BSC E1 1.60 BSC e 0.95 TYP L 0.30 L1 0.40 0.20 0.50 0.60 REF L2 0.25 BSC 0º θ 8º TOP VIEW A2 A b q L A1 c L1 SIDE VIEW END VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-193. www.onsemi.com 9 L2 CAT24AA01, CAT24AA02 Ordering Information Device Order Number Specific Device Marking Package Type CAT24AA01TDI−GT3 RS SOT−23−5 I = Industrial (−40°C to +85°C) NiPdAu Tape & Reel, 3,000 Units / Reel CAT24AA02TDI−GT3 RS SOT−23−5 I = Industrial (−40°C to +85°C) NiPdAu Tape & Reel, 3,000 Units / Reel Temperature Range Lead Finish Shipping 8. All packages are RoHS−compliant (Lead−free, Halogen−free). 9. The standard lead finish is NiPdAu. 10. For additional package and temperature options, please contact your nearest ON Semiconductor sales office. 11. For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. ON Semiconductor is licensed by Philips Corporation to carry the I2C Bus Protocol. ON Semiconductor and the are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 10 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative CAT24AA01/D