PRODUCT DATASHEET HighBay series last update 24/5/2017 DETAILS Product Number CS14891_HB-IP-2X6-M Family HighBay Type Assembly Color clear Diameter 173 + 71,4 mm Height 11,39 mm Style rectang Optic Material PMMA Holder Material Fastening pin, screw Status production ready ROHS Comliant Yes Date Updated 24/05/2017 OPTICAL PROPERTIES Viewing Light Effi- LED Angle Beam ciency cd/lm Connector XM-L 27 deg Medium 94 % 3.100 - XP-G3 32 deg Medium 94 % 2.400 - XP-L 39 deg Medium 94 % 1.700 - XP-L2 39 deg Medium 94 % 1.700 - XT-E 25 deg Medium 92 % 3.100 - H35C1 (LEMWA33) sim: 35 Medium sim: 94 % sim: 2.100 - LUXEON XR-TX (L2T0-xxyy012M) 28 deg Medium 94 % 2.950 - LUXEON T 29 deg Medium 94 % 2.700 - LUXEON 5050 sim: 37 Medium sim: 93 % sim: 1.980 - NVSxE21A 24 deg Medium 92 % 4.100 - Oslon Square PC 29 deg Medium 93 % 2.690 - Fortimo FastFlex LED board 2x6 DPX G432 deg Medium 94 % 2.400 - Fortimo FastFlex LED board 2x6 DP G4 sim: 26 Medium sim: 94 % sim: 3.950 - Z5M1/Z5M2 30 deg Medium 93 % 2.630 - Z8Y22P 30 deg Medium 93 % 2.500 - June 13th 2017 8:00 Copyright Ledil Oy - Subject to change without prior notice - Page 1/1 Ledil Oy Salorankatu 10 24240 SALO, Finland http://www.ledil.com email: [email protected] FAX: +358-2-733 8001 2 Fasten middle screws first. Recommended torque with pan head screw: 0.57Nm (for 1.6mm thick PCB, no thermal pad) (rib) 2.65 A 3 Silicone seal is tested to work in LEDiL test assemblies. Customer is recommended to test the sealing in the end product due many variables, such as heat sink surface and possible chemical traces 9.64 1.6 (1.6mm pcb) Section view C-C Scale 1:1 1 2 71.4 1 Section view D-D Scale 2:1 INDEX PART NO DESCRIPTION MATERIAL COLOUR D E 173 H B 3.2 Ribs Tolerances if not otherwise shown According to DIN ISO 2768-1 Linear measures: up to 30mm class M, otherwise class C According to DIN ISO 2768-2 Form and position: class L THIRD ANGLE PROJECTION: E M3 screw size 2 3.4 D 3.4 6 5.35 50.8 Wiring: PCB is fully sealed between the lens with silicone seal and the heatsink. Wiring needs to be done through the PCB and heatsink to maintain high IP rating. (silicone) 25.4 61 ( 44.9 ) 54.2 3.2 1.65 54.2 4 Detail B Scale 2:1 11.39 1.7 54.2 3 LED position A Detail A Scale 2:1 5.35 2 4 B 3.2 1 PCB typically 146,6mm PCB typically 45mm 25.4 C D E F G H ( 146.5 ) G This drawing is the property of LEDiL Oy. It may not be reproduced, copied or communicated without a written agreement with LEDiL Oy. C14018 - 2X6-SEAL25 HB-IP-2X6 Silicone PMMA Ledil Oy Salorankatu 10 FIN 24240 SALO Finland DRAWING TITLE MechDrawing_HB-IP-2X6 SIZE A3 SCALE 1 PART NUMBER 1:1 WEIGHT - B SHEET A 1/1 NOTE: The typical divergence will be changed by different color, chip size and chip position tolerance. The typical total divergence is the full angle measured where the luminous intensity is half of the peak value.