Revised June 2005 FST16862 20-Bit Bus Switch General Description Features The Fairchild Switch FST16862 provides 20-bits of highspeed CMOS TTL-compatible bus switching. The low On Resistance of the switch allows inputs to be connected to outputs without adding propagation delay or generating additional ground bounce noise. ■ 4: switch connection between two ports. The device is organized as a 20-bit bus switch. When OEX is LOW, the switch is ON and Port A is connected to Port B. When OEX is HIGH, a high impedance state exists between the A and B Ports. ■ Control inputs compatible with TTL level. ■ Minimal propagation delay through the switch. ■ Low lCC. ■ Zero bounce in flow-through mode. Ordering Code: Order Number FST16862QSP FST16862MTD Package Number Package Description MQA48A 48-Lead Quarter Size Very Small Outline Package (QVSOP), JEDEC MO-154, 0.150" Wide (Preliminary) MTD48 48-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code. Logic Diagram © 2005 Fairchild Semiconductor Corporation DS500702 www.fairchildsemi.com FST16862 20-Bit Bus Switch October 2001 FST16862 Connection Diagram Truth Table Inputs OEx L H Inputs/Outputs A, B B A Z Pin Descriptions www.fairchildsemi.com 2 Pin Name Description OEx Bus Switch Enables A Bus A B Bus B Supply Voltage (VCC) DC Switch Voltage (VS) (Note 2) DC Input Voltage (VIN) (Note 3) DC Input Diode Current (lIK) VIN 0V Recommended Operating Conditions (Note 4) 0.5V to 7.0V 0.5V to 7.0V 0.5V to 7.0V 50 mA DC Output (IOUT) Current 128 mA DC VCC/GND Current (ICC/IGND) Storage Temperature Range (TSTG) 4.0V to 5.5V Power Supply Operating (VCC) Input Voltage (VIN) 0V to 5.5V Output Voltage (VOUT) 0V to 5.5V Input Rise and Fall Time (tr, tf) r100 mA 65qC to 150 qC Switch Control Input 0 ns/V to 5 ns/V Switch I/O 0 ns/V to DC -40 qC to 85 qC Free Air Operating Temperature (TA) Note 1: The “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum rating. The “Recommended Operating Conditions” table will define the conditions for actual device operation. Note 2: VS is the voltage observed/applied at either the A or B Ports across the switch. Note 3: The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. Note 4: Unused control inputs must be held HIGH or LOW. They may not float. DC Electrical Characteristics Symbol VCC (V) Parameter 40 qC to 85 qC TA Min Typ (Note 5) Max 1.2 4.5 Units IIN 18 mA VIK Clamp Diode Voltage VIH HIGH Level Input Voltage 4.0 - 5.5 VIL LOW Level Input Voltage 4.0 - 5.5 0.8 V II Input Leakage Current 5.5 r1.0 PA 0 r1.0 PA VIN 5.5 r1.0 PA 0 d A, B d VCC 2.0 V Conditions V 0 d VIN d 5.5V 5.5V IOZ OFF-STATE Leakage Current RON Switch On Resistance 4.5 4 7 : VIN 0V, IIN 64 mA (Note 6) 4.5 4 7 : VIN 0V, IIN 30 mA 4.5 7 12 : VIN 2.4V, IIN 15 mA 4.0 11 20 : VIN 2.4V, IIN 15 mA VCC or GND, IOUT ICC Quiescent Supply Current 5.5 3 PA VIN ' ICC Increase in ICC per Input 5.5 2.5 mA One Input at 3.4V (Note 7) Note 5: Typical values are at VCC 0 Other Inputs at VCC or GND 5.0V and TA 25qC Note 6: Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower of the voltages on the two (A or B) pins. Note 7: Per TTL driven input, control pins only. 3 www.fairchildsemi.com FST16862 Absolute Maximum Ratings(Note 1) FST16862 AC Electrical Characteristics CL Symbol Parameter tPHL, tPLH Propagation Delay Bus-to-Bus (Note 8) tPZH, tPZL Output Enable Time tPHZ, tPLZ TA 40 qC to 85 qC, 50pF, RU RD 500: VCC 4.5 – 5.5V Min Max Output Disable Time 1.0 1.0 VCC 4.0V Min Units Figure Number Conditions Max 0.25 0.25 ns VI OPEN Figures 1, 2 5.0 5.3 ns VI 7V for tPZL VI OPEN for tPZH Figures 1, 2 VI 7V for tPLZ VI OPEN for tPHZ 6.0 6.3 ns Figures 1, 2 Note 8: This parameter is guaranteed by design but is not tested. The bus switch contributes no propagation delay other than the RC delay of the typical On Resistance of the switch and the 50pF load capacitance, when driven by an ideal voltage source (zero output impedance). Capacitance (Note 9) Symbol CIN CI/O Note 9: TA Parameter Typ Max Units Conditions Control Pin Input Capacitance 3 pF VCC Input/Output Capacitance “OFF State” 6 pF VCC, OE 25qC, f 1 Mhz, Capacitance is characterized but not tested. AC Loading and Waveforms Note: Input driven by 50: source terminated in 50: Note: CL includes load and stray capacitance Note: Input PRR 1.0 MHz, tW 500 ns FIGURE 1. AC Test Circuit FIGURE 2. AC Waveforms www.fairchildsemi.com 4 5.0V, VIN 0V 5.0V, VIN 0V FST16862 Physical Dimensions inches (millimeters) unless otherwise noted 48-Lead Quarter Size Very Small Outline Package (QVSOP), JEDEC MO-154, 0.150" Wide Package Number MQA48A (Preliminary) 5 www.fairchildsemi.com FST16862 20-Bit Bus Switch Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 48-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide Package Number MTD48 Technology Description The Fairchild Switch family derives from and embodies Fairchild’s proven switch technology used for several years in its 74LVX3L384(FST3384) bus switch product. Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com www.fairchildsemi.com 6