Z-Power LED X10490 Technical Data Sheet Specification FCW321G SSC Drawn Approval CUSTOMER Approval Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Technical Data Sheet CONTENTS 1. Absolute Maximum Ratings 2. Electro Characteristics 3. Outline Dimension 4. Electro-Optical characteristic Diagram 5. Color & Binning 6. Rank of WH603R 7. Reliability tests 8. Packing 9. Soldering 10. Precaution for use Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Technical Data Sheet FCW321G Description Features 사진 - Vary Thin PKG of Reflector type - Surface-mounted chip LED device. - Pb-free and RoHS complaint component. - High brightness - Low Thermal Resistance - Tape and Reel packing. FCW321G • 3.5 X 2.8 X 0.6 mm • Emitted Color : White • CIE chromaticity x : 0.3 • y : 0.3 Material : InGaN Applications • Electric appliance • Other decoration lighting Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Technical Data Sheet 1. Absolute maximum ratings (Ta=25℃) Parameter Symbol Value Unit Power Dissipation Pd 306 mW Forward Current IF 90 mA Peak Forward Current IFM *1 300 mA Reverse Voltage VR 5 V Operation Temperature Topr. -30 ~ 85 ℃ Storage Temperature Tstg. -40 ~ 100 ℃ *1 IFM conditions: Pulse width Tw≤0.1ms and Duty ratio≤1/10. 2. Electro-Optical Characteristics Characteristics Forward Voltage Zener Voltage Luminous Intensity *2 Symbol VF VF(Z) IV (Ta=25℃) Condition Min Typ Max IF=90㎃ 2.8 3.4 3.8 IF=1㎂ 1.7 2.7 IF=10㎂ 2.0 2.7 IF(Z)=5mA 0.7 - 1.5 IF=90㎃ 5 7 13 IF=200㎃ (Flash mode) *3 7 12.5 - IF=300㎃ (Peak current mode) *4 9 17 - Unit V V cd Illumination lx IF=200㎃ (Flash mode) *3 - 25.5 - [email protected] - 12.5 - lx@1m Luminous Flux lm IF=90㎃ - 39.5 - lm Chromaticity Coordinates X IF=90㎃ 0.295 0.330 0.368 Y IF=90㎃ 0.288 0.330 0.380 Viewing Angle Δ1/2θ IF=90㎃ - 120 - ˚ *2 The luminous intensity IV is measured at the peak of the spatial pattern which may not be aligned with the mechanical axis of the LED package. *3 Flash mode condition is Pulse width Tw = 2sec, Duty ratio = 2 / 7 *4 Peak current mode is Pulse width Tw≤300ms, Duty ratio≤1/10 [Note] ( Tolerance : IV±10%, color coordinate ±0.01, VF ±0.1 ) Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Technical Data Sheet 3.Outline Dimension [TOP VIEW] [SIDE VIEW] [BOTTOM VIEW] [INNER CIRCUIT] ( Tolerance: ±0.1, Unit: mm ) - Recommended Soldering Design Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Forward Current vs. Forward Voltage (Ta=25 OC ) 1000 Forward Current [mA] 100 10 1 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 Forward Voltage [V] Relative Luminous Intensity vs Forward Current (Ta=25 OC ) 3.0 2.5 Relative Luminosity [a.u.] Z-Power LED X10490 Technical Data Sheet 4. Electro-Optical characteristic Diagram 2.0 1.5 1.0 0.5 0.0 0 50 100 150 200 Forward Current [mA] 250 300 Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Technical Data Sheet 4. Electro-Optical characteristic Diagram Ambient Temperature vs. Allowable Forward Current 100 ) A m (F I t n e r r u c d r a w r o F 80 60 40 20 0 25 50 75 ) C o ( a T e r u t a r e p m e t t n e i b m A 0 -25 100 Radiation Diagram (Ta=25 OC ) 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 120 130 140 150 160 110 100 90 80 70 60 50 40 30 20 170 10 180 0 Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Spectrum (TA=25℃, IF=90mA) 1.0 Relative Luminous Intensity (a.u.) Z-Power LED X10490 Technical Data Sheet 4. Electro-Optical characteristic Diagram 0.8 0.6 0.4 0.2 0.0 350 400 450 500 550 600 650 700 750 800 Wavelength (nm) Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Technical Data Sheet 5. Color & Binning 0.9 520 0.8 540 0.7 560 0.6 CIE (y) 500 580 0.5 0.4 600 620 0.3 640 0.2 0.1 0.0 0.0 480 460 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 CIE (x) Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) 0.40 0.38 Y - Coordinate Z-Power LED X10490 Technical Data Sheet 5. Color & Binning C rank 0.36 0.34 B rank 0.32 0.30 0.28 0.30 0.32 0.34 0.36 0.38 X - Coordinate ※ Color Rank Bin B C CIE x CIE y 0.3054 0.3150 0.3300 0.3061 0.3430 0.3300 0.3180 0.3370 0.3430 0.3300 0.3180 0.3370 0.3425 0.3800 0.3675 0.3730 Rev. 00 September 2008 * Measurement Uncertainty of the Color Coordinates : ± 0.01 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Technical Data Sheet 6. Rank of FCW321G (1) Luminous Intensity: Iv [mcd] Rank Iv [mcd] A 5000 ~ 8000 B 8000 ~ 13000 Condition IF =90mA (2) Color Coordinate: x, y Rank B C 1 2 3 4 x 0.3054 0.3300 0.3430 0.3180 y 0.3150 0.3061 0.3300 0.3370 x 0.3430 0.3180 0.3425 0.3675 y 0.3300 0.3370 0.3800 0.3730 Condition IF =90mA (3) Forward voltage: VF VF [V] Condition 2.8 ~ 3.8 IF =90mA Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Technical Data Sheet 7. Reliability Tests Item Condition Note Failures Life Test Ta = RT, IF = 90mA 1000hrs 0/22 High Temperature Operating Ta = 85ºC, IF = 90mA 1000hrs 0/22 Low Temperature Operating Ta = -30ºC, IF = 90mA 1000hrs 0/22 Thermal Shock Ta = -30ºC (30min) ~ 85ºC (30min) (Transfer time : 10sec, 1Cycle = 1hr) 100 cycles 0/40 Resistance to soldering Heat Ts = 255 ± 5ºC, t = 10sec 1 time 0/22 ESD (Human Body Model) 1kV, 1.5kΩ ; 100pF 1 time 0/22 High Temperature Storage Ta = 100ºC 1000hrs 0/22 Low Temperature Storage Ta = -40ºC 1000hrs 0/22 Temperature Humidity Storage Ta = 85ºC, RH = 85% 1000hrs 0/22 Temperature Humidity Operating Ta = 85ºC, RH = 85%, IF = 90mA 100hrs 0/22 < Judging Criteria For Reliability Tests > VF USL[1] X 1.2 IR USL X 2.0 ФV LSL [2] X 0.7 Notes : [1] USL : Upper Standard Level [2] LSL : Lower Standard Level. Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) 4.0±0.1 2.9±0.1 +0.1 -0 0.25±0.05 (2.75) 8.0±0.1 3.5±0.05 3.7±0.1 1.5 1.75±0.1 Marking Direction 0.85±0.1 180 11.4 +0 -3 9 ±0.3 +0.2 -0 2 ±0.2 60 Z-Power LED X10490 Technical Data Sheet 8. Packing 22 13 ±0.2 Label Tolerance: ±0.2, Unit: ㎜ (1) Quantity: 2,000pcs./Reel (2) Cumulative Tolerance: Cumulative Tolerance/10pitches to be ±0.2mm (3) Adhesion Strength of Cover Tape: Adhesion strength to be 0.1-0.7N when the over tape is turned off from the carrier tape at10˚angle to be the carrier tape. (4) Package: P/N, Manufacturing data Code No. and quantity to be indicated on a damp proof Package. Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Technical Data Sheet ● Reel Packing Structure Reel Product No.: SSC-FCW321G Quantity : 2000 Batch/Lot number :############ Aluminum Vinyl Bag Product No.: SSC-FCW321G Quantity : 2000 Batch/Lot number : ############ Outer Box *Material: Paper(SW3B(B)) TYPE SIZE(mm) a 7inch 245 b 220 c 142 c TUV CHIP LED MADE IN KOREA Acriche Semiconductor EcoLight RoHS b a PART : SSC-FCW321G CODE : Q'YT : 20,000EA LOT NO : DATE : SEOUL SEMICONDUCTOR CO.,LTD Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Technical Data Sheet 9. Soldering (1) Lead Solder Lead Solder Lead Solder 2.5~5 o C / sec. Pre-heat 120~150℃ Pre-heat time 120 sec. Max. Peak-Temperature 240℃ Max. Soldering time Condition 10 sec. Max. 2.5~5 C / sec. Pre-heating 120~150 oC 240 oC Max. 10 sec. Max. 60sec. Max. Above 200 oC 120sec. Max. (2) Lead-Free Solder Lead-frame Solder 1~5 o C / sec. Lead Free Solder Pre-heat 150~200℃ Pre-heat time 120 sec. Max. Peak-Temperature 260℃ Max. Soldering time Condition 10 sec. Max. 1~5 o C / sec. Pre-heating 150~200 o C 260 oC Max. 10 sec. Max. 60sec. Max. Above 220 oC 120sec. Max. (3) Hand Soldering conditions Do not exceed 3 seconds at maximum 280ºC under soldering iron. (4) The encapsulated material of the LEDs is silicone. Precautions should be taken to avoid the strong pressure on the encapsulated part. So when using the chip mounter, the picking up nozzle that does not affect the silicone resign should be used. Note : In case that the soldered products are reused in soldering process, we don’t guarantee the products. Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00) Z-Power LED X10490 Technical Data Sheet 10. Precaution for use (1) Storage In order to avoid the absorption of moisture, it is recommended to store in the dry box (or desiccator) with a desiccant. Otherwise, to store them in the following environment is recommended. Temperature : 5℃~30℃ Humidity : 60%HR max. (2) Attention after opened However LED is corresponded SMD, when LED be soldered dip, interfacial separation may affect the light transmission efficiency, causing the light intensity to drop. Attention in followed. a. After opened and mounted, the soldering shall be quickly. b. Keeping of a fraction Temperature : 5 ~ 40℃ Humidity : less than 30% (3) In case of more than 1 week passed after opening or change color of indicator on desiccant components shall be dried 10-12hr. at 60±5℃. (4) In case of supposed the components is humid, shall be dried dip-solder just before. 100Hr at 80±5℃ or 12Hr at 100±5℃. (5) Any mechanical force or any excess vibration shall not be accepted to apply during cooling process to normal temp. after soldering. (6) Quick cooling shall not be avoid. (7) Components shall not be mounted on warped direction of PCB. (8) Anti radioactive ray design is not considered for the products listed here in. (9) Gallium arsenide is used in some of the products listed in this publication. These products are dangerous if they are burned or smashed in the process of disposal. It is also dangerous to drink the liquid or inhale the gas generated by such products when chemically disposed. (10) This device should not be used in any type of fluid such as water, oil, organic solvent and etc. When washing is required, IPA should be used. (11) When the LEDs are illuminating, operating current should be decided after considering the ambient maximum temperature. (12) LEDs must be stored to maintain a clean atmosphere. If the LEDs are stored for 3 months or more after being shipped from SSC, a sealed container with a nitrogen atmosphere should be used for storage. (13) The LEDs must be soldered within seven days after opening the moisture-proof packing. (14) Repack unused products with anti-moisture packing, fold to close any opening and then store in a dry place. (15) The appearance and specifications of the product may be modified for improvement without notice. Rev. 00 September 2008 www.ZLED.com Document No. : SSC-QP-7-07-24 (Rev.00)