DTB114TK Transistors Digital transistor (built-in resistor) DTB114TK zFeatures 1) Built-in bias resistors enable the configuration of an inverter circuit without connecting external input resistors. 2) The bias resistors consist of thin-film resistors with complete isolation to allow positive biasing of the input, and parasitic effects are almost completely eliminated. 3) Only the on / off conditions need to be set for operation, making device design easy. 4) Higher mounting densities can be achieved. zCircuit schematic C B R1 E E : Emitter C : Collector B : Base zAbsolute maximum ratings (Ta=25°C) Symbol Limits Unit Collector-base voltage VCBO −50 V Collector-emitter voltage VCEO −40 V Emitter-base voltage VEBO −5 V Collector current IC −500 mA Collector power dissipation PC 200 mW Junction temperature Tj 150 C Storage temperature Tstg −55 to +150 C Parameter zPackage, marking, and packaging specifications Part No. DTB114TK Package SMT3 Marking F94 Packaging code T146 Basic ordering unit (pieces) 3000 Rev.A 1/2 DTB114TK Transistors zExternal characteristics (Ta=25°C) Symbol Min. Typ. Max. Unit Collector-base breakdown voltage Parameter BVCBO −50 − − V IC= −50µA Collector-emitter breakdown voltage BVCEO −40 − − V IC= −1mA Emitter-base breakdown voltage BVEBO −5 − − V IE= −50µA Collector cutoff current ICBO − − −0.5 µA VCB= −50V Emitter cutoff curren IEBO − − −0.5 µA VEB= −4V VCE(sat) − − −0.3 V IC/IB= −50mA/−2.5mA DC current transfer ratio hFE 100 250 600 − IC= −50mA , VCE= −5V Input resistance R1 7 10 13 kΩ − Transition frequency fT − 200 − MHz VCE= −10V , IE=50mA , f=100MHz ∗ Collector-emitter saturation voltage Conditions ∗Transition frequency of the device. 1k VCE=5V Ta=25°C DC CURRENT GAIN : hFE 500 Ta=100°C 200 Ta= −40°C 100 50 20 10 5 2 1 500µ 1m 2m 5m 10m 20m 50m 100m 200m 500m COLLECTOR CURRENT : IC (A) Fig.1 DC current gain vs. Collector current COLLECTOR SATURATION VOLTAGE : VCE(sat) (V) zElectrical characteristics curves 1 IC/IB=20/1 500m 200m Ta=100°C Ta=25°C 100m 50m Ta= −40°C 20m 10m 5m 2m 1m 500µ 1m 2m 5m 10m 20m 50m 100m 200m 500m COLLECTOR CURRENT : IC (A) Fig.2 Collector-emitter saturation voltage vs. Collector current Rev.A 2/2 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1