AD AD8598AN Dual 7 ns single supply comparator Datasheet

a
FEATURES
7 ns Propagation Delay
Single Supply Operation: +3 V to +10 V
Low Power
Symmetrical Layout
Latch Function
TSSOP Packages
APPLICATIONS
Clock Recovery and Clock Distribution
High Speed Data
Line Receivers
Phase Detectors
Digital Communications
I and Q Detection
High Speed Sampling
Upgrade for MAX912
Satellite Receivers
PCMCIA Cards
Wireless Data Links
Battery Operated Instrumentation
Dual 7 ns
Single Supply Comparator
AD8598
PIN CONFIGURATIONS
N-16, RU-16 and R-16A
QB
QA 1
16
QA 2
15
QB
GND 3
14
GND
LEA 4
AD8598
13
LEB
NC 5
TOP VIEW
(Not to Scale)
12
NC
V– 6
11
V+
IN A– 7
10
IN B–
IN A+ 8
9
IN B+
NC = NO CONNECT
GENERAL DESCRIPTION
The AD8598 is a dual 7 ns comparator with digital latches.
Separate supplies enable the input stage to be operated from
+5 V to as high as ± 5 V.
Ultrafast 7 ns propagation delay makes the AD8598 a good
choice for timing circuits and line receivers. Propagation delays
for rising and falling signals are closely matched and track over
temperature. This matched delay makes the AD8598 a good
choice for clock recovery, since the duty cycle of the output will
match the duty cycle of the input.
The AD8598 has the same pinout as the DIP version of the
AD9698. For a single comparator like the AD8598, please refer
to the AD8561 data sheet.
The AD8598 is specified over the industrial (–40°C to +85°C)
temperature range. The AD8598 is available in both the 16-lead
plastic DIP, 16-lead TSSOP or narrow R-16A surface mount
packages.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 1998
AD8598–SPECIFICATIONS
ELECTRICAL SPECIFICATIONS (@ V+ = +5.0 V, V– = V
Parameter
Symbol
INPUT CHARACTERISTICS
Offset Voltage
VOS
Offset Voltage Drift
Input Bias Current
Input Offset Current
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
Large Signal Voltage Gain
Input Capacitance
LATCH ENABLE INPUT
Logic “1” Voltage Threshold
Logic “0” Voltage Threshold
Logic “1” Current
Logic “0” Current
Latch Enable
Pulsewidth
Setup Time
Hold Time
∆VOS/∆T
IB
IB
IOS
VCM
CMRR
AVO
CIN
VIH
VIL
IIH
IIL
GND
= 0 V, TA = +25ⴗC unless otherwise noted)
Conditions
Min
–40°C ≤ TA ≤ +85°C
VCM = 0 V
–40°C ≤ TA ≤ +85°C
VCM = 0 V
0 V ≤ VCM ≤ +3.0 V
RL = 10 kΩ
–6
–7
0.0
65
+2.0
VLH = +3.0 V
VLL = +0.3 V
–1.0
–4
tPW(E)
tS
tH
Typ
Max
Units
2.3
7
8
mV
mV
µV/°C
µA
µA
µA
V
dB
V/V
pF
4
–3
–3.5
±4
+3.0
85
+3,000
3.0
+1.65
+1.60
–0.3
–2
+0.8
V
V
µA
µA
6
1
1.2
ns
ns
ns
+3.5
+0.25
V
V
V
DIGITAL OUTPUTS
Logic “1” Voltage
Logic “1” Voltage
Logic “0” Voltage
VOH
VOH
VOL
IOH = –50 µA, ∆VIN > 250 mV
IOH = –3.2 mA, ∆VIN > 250 mV
IOL = 3.2 mA, ∆VIN > 250 mV
DYNAMIC PERFORMANCE␣
Propagation Delay
tP
200 mV Step with 100 mV Overdrive
–40°C ≤ TA ≤ +85°C
100 mV Step with 5 mV Overdrive
6.75
8
8
9.8
13
ns
ns
ns
∆tP
100 mV Step with 100 mV Overdrive1
20% to 80%
80% to 20%
0.5
3.8
1.5
2.0
ns
ns
ns
PSRR
I+
+4.5 V ≤ V+ ≤ +5.5 V
Propagation Delay
Differential Propagation Delay
(Rising Propagation Delay vs.
Falling Propagation Delay)
Rise Time
Fall Time
POWER SUPPLY␣
Power Supply Rejection Ratio
Positive Supply Current (V+ Pin)
tP
Ground Supply Current (GND Pins)
IGND
Analog Supply Current (V– Pin)
I–
–40°C ≤ TA ≤ +85°C
VO = 0 V, RL = ∞
–40°C ≤ TA ≤ +85°C
–40°C ≤ TA ≤ +85°C
+3.5
+2.4
50
65
9.0
4.4
4.6
+0.4
12.0
15.0
6.6
7.6
9.0
11.0
dB
mA
mA
mA
mA
mA
mA
NOTES
1
Guaranteed by design.
Specifications subject to change without notice.
–2–
REV. A
AD8598
ELECTRICAL SPECIFICATIONS (@ V+ = +5.0 V, V
Parameter
Symbol
INPUT CHARACTERISTICS
Offset Voltage
VOS
Offset Voltage Drift
Input Bias Current
Input Offset Current
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
Large Signal Voltage Gain
Input Capacitance
LATCH ENABLE INPUT
Logic “1” Voltage Threshold
Logic “0” Voltage Threshold
Logic “1” Current
Logic “0” Current
Latch Enable
Pulsewidth
Setup Time
Hold Time
∆VOS/∆T
IB
IB
IOS
VCM
CMRR
AVO
CIN
VIH
VIL
IIH
IIL
GND
= 0 V, V– = –5 V, TA = +25ⴗC unless otherwise noted)
Conditions
Min
–40°C ≤ TA ≤ +85°C
VCM = 0 V
–40°C ≤ TA ≤ +85°C
VCM = 0 V
–5.0 V ≤ VCM ≤ +3.0 V
RL = 10 kΩ
–6
–7
–5.0
65
+2.0
VLH = +3.0 V
VLL = +0.3 V
–1
–4
Typ
Max
Units
1
7
8
mV
mV
µV/°C
µA
µA
µA
V
dB
V/V
pF
4
–3
–2.5
±4
+3.0
85
+3,000
3.0
+1.65
+1.60
–0.5
–2
+0.8
6
1.0
1.2
tPW(E)
tS
tH
V
V
µA
µA
ns
ns
ns
DIGITAL OUTPUTS
Logic “1” Voltage
Logic “0” Voltage
VOH
VOL
IOH = –3.2 mA
IOL = 3.2 mA
DYNAMIC PERFORMANCE␣
Propagation Delay
tP
200 mV Step with 100 mV Overdrive
–40°C ≤ TA ≤ +85°C
100 mV Step with 5 mV Overdrive
6.5
8
7
9.8
13
ns
ns
ns
∆tP
100 mV Step with 100 mV Overdrive1
20% to 80%
80% to 20%
0.5
3.8
1.5
1
2
ns
ns
ns
ns
PSRR
± 4.5 V ≤ VCC and VEE ≤ ± 5.5 V
VO = 0 V, RL = ∞
Propagation Delay
Differential Propagation Delay
(Rising Propagation Delay vs.
Falling Propagation Delay)
Rise Time
Fall Time
Dispersion
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current
Positive Supply Current (V+ Pin)
tP
I+
Ground Supply Current (GND Pins)
IGND
Analog Supply Current (V– Pin)
I–
–40°C ≤ TA ≤ +85°C
VO = 0 V, RL = ∞
–40°C ≤ TA ≤ +85°C
–40°C ≤ TA ≤ +85°C
NOTES
1
Guaranteed by design.
Specifications subject to change without notice.
REV. A
–3–
+2.6
55
+3.5
+0.2
+0.3
70
9.4
4.4
4.8
V
V
dB
13.0
15.0
6.6
7.6
9.0
11.0
mA
mA
mA
mA
mA
mA
AD8598–SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
Parameter
(@ V+ = +3.0 V, V– = VGND = 0 V, TA = +25ⴗC unless otherwise noted)
Symbol
INPUT CHARACTERISTICS␣
Offset Voltage
Input Bias Current
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS␣
Output High Voltage1
Output Low Voltage
POWER SUPPLY␣
Power Supply Rejection Ratio
Supply Currents
Positive Supply Current (V+ Pin)
Min
Typ
VCM = 0 V
–40°C ≤ TA ≤ +85°C
–6
–7
0
50
–3.0
–4
VOS
IB
IB
VCM
CMRR
+0.1 V ≤ VCM ≤ +1.5 V
VOH
VOL
IOH = –3.2 mA, VIN > 250 mV
IOL = +3.2 mA, VIN > 250 mV
PSRR
+2.7 V ≤ VCC, VEE ≤ +6 V
VO = 0 V, RL = ∞
I+
Ground Supply Current (GND Pins)
IGND
Analog Supply Current (V– Pin)
I–
DYNAMIC PERFORMANCE␣
Propagation Delay
Conditions
tP
Max
Units
7
mV
µA
µA
V
dB
+1.5
+1.2
+0.3
40
dB
8.0
–40°C ≤ TA ≤ +85°C
3.2
–40°C ≤ TA ≤ +85°C
4.8
–40°C ≤ TA ≤ +85°C
100 mV Step with 20 mV Overdrive2
V
V
8.5
9.0
11.0
5.0
6.0
6.6
7.6
mA
mA
mA
mA
mA
mA
9.8
ns
NOTES
1
Output high voltage without pull-up resistor. It may be useful to have a pull-up resistor to V+ for +3 V operation.
2
Guaranteed by design.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS
Total Analog Supply Voltage . . . . . . . . . . . . . . . . . . . . . +14 V
Digital Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . +7 V
Analog Positive Supply–Digital Positive Supply . . . . . –600 mV
Input Voltage1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±7 V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . ±8 V
Output Short-Circuit Duration to GND . . . . . . . . . Indefinite
Storage Temperature Range
N, R, RU Package . . . . . . . . . . . . . . . . . . –65°C to +150°C
Operating Temperature Range . . . . . . . . . . . –40°C to +85°C
Junction Temperature Range
N, R, RU Package . . . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature Range (Soldering, 10 sec) . . . . . . . +300°C
Package Type
␪JA2
␪JC
Units
16-Lead Plastic DIP
16-Lead SOIC
16-Lead TSSOP
103
158
240
43
43
43
°C/W
°C/W
°C/W
NOTES
1
The analog input voltage is equal to ±7 V or the analog supply voltage, whichever
is less.
2
θ JA is specified for the worst case conditions, i.e., θ JA is specified for device in socket
for P-DIP and θ JA is specified for device soldered in circuit board for SOIC and
TSSOP packages.
ORDERING GUIDE
Model
Temperature
Range
Package
Descriptions
Package
Options
AD8598AN
AD8598ARU
AD8598AR
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
16-Lead Plastic DIP
16-Lead Thin Shrink Small Outline (TSSOP)
16-Lead Narrow Body IC
N-16
RU-16
R-16A
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD8598 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
–4–
WARNING!
ESD SENSITIVE DEVICE
REV. A
AD8598
Typical Performance Characteristics (V+ = +5 V, V– = 0 V, T = +25ⴗC unless otherwise noted)
A
5
3
+258C
2
1
0
22.5 22.0 21.5 21.0 20.5 0
0.5 1.0 1.5
DIFFERENTIAL INPUT VOLTAGE – mV
Figure 1. Output Voltage vs. Differential Input Voltage
100
25 24 23 22 21 0 1 2 3
INPUT VOLTAGE – mV
4
tPD 2
FALLING EDGE
tPD +
FALLING EDGE
5
20
30
40
10
LOAD CAPACITANCE – pF
0
10
5
30
STEP SIZE = 800mV
400mV
200mV
20
100mV
10
0
0.5
1
1.5
SOURCE RESISTANCE – kV
15
5
5
4.75
5
5.25
SUPPLY VOLTAGE – Volts
5.5
Figure 6. Propagation Delay vs. Positive Supply Voltage
4
15
125
3
2408C
+1258C
10
5
0
100
Figure 7. Propagation Delay vs.
Temperature
REV. A
50
SINGLE SUPPLY
TA = +258C
STEP SIZE = 100mV
OVERDRIVE = 5mV
CAPACITANCE LOAD = 10pF
0
4.5
TIME – ns
PROPAGATION DELAY – ns
10
0
25
75
50
TEMPERATURE – 8C
40
+258C
VS = +5V, SINGLE SUPPLY
STEP SIZE = 100mV
OVERDRIVE = 5mV,
LOAD CAPACITANCE = 10pF
–25
20
30
OVERDRIVE – mV
10
20
0
–50
10
Figure 3. Propagation Delay vs.
Overdrive
2
Figure 5. Propagation Delay vs.
Source Resistance
20
0
20
VS = +5V, SINGLE SUPPLY
TA = +258C
OVERDRIVE = 10mV
CAPACITANCE LOAD = 10pF
0
50
TA = +258C
0
PROPAGATION DELAY – ns
15
15
5
Figure 2. Typical Distribution of Input
Offset Voltage
PROPAGATION DELAY – ns
PROPAGATION DELAY – ns
200
40
VS = +5V, SINGLE SUPPLY
STEP SIZE = 100mV
OVERDRIVE LOAD = 5mV
Figure 4. Propagation Delay vs. Load
Capacitance
PROPAGATION DELAY – ns
300
0
20
15
400
PROPAGATION DELAY – ns
NUMBER OF COMPARATORS
OUTPUT VOLTAGE – Volts
2408C
10
VS = +5V, SINGLE SUPPLY
STEP SIZE = 100mV
CAPACITANCE LOAD = 10pF
VS = +5V, SINGLE SUPPLY
4
0
20
500
+1258C
VS = +5V
STEP SIZE = 100mV
OVERDRIVE = 5mV
LOAD CAPACITANCE = 10pF
0
2
3
4
1
COMMON-MODE VOLTAGE – Volts
HOLD TIME
SETUP TIME
1
5
Figure 8. Propagation Delay vs. VCM
–5–
2
0
–50
–25
0
25
50
75
TEMPERATURE – 8C
100
125
Figure 9. Latch Setup-and-Hold Time
vs. Temperature
AD8598
5.0
0.4
TA = 2408C
TA = +258C
0.2
TA = +1258C
0.1
4.4
TA = +1258C
3.8
TA = +258C
3.2
TA = 2408C
2.6
2.0
0
3
0
6
9
12
SINK CURRENT – mA
0
15
Figure 10. Output Low Voltage, VOL
vs. Sink Current
V+ = +5V, V2 = 0V
28.0
V+ = +5V, V2 = 25V
212.0
216.0
220.0
–75 –50 –25
24.0
TA = 2408C
28.0
TA = +258C
212.0
TA = +1258C
216.0
0
70
60
50
40
+1258C
30
20
+258C
–408C
4
6
8
10
SUPPLY VOLTAGE – Volts
12
Figure 13. Analog Supply Current vs.
Supply Voltage
21
22
23
24
10
0
2
0 25 50 75 100 125 150
TEMPERATURE – 8C
Figure 12. Analog Supply Current vs.
Temperature for ± 5 V Supplies
80
POSITIVE SUPPLY CURRENT – mA
I–, ANALOG SUPPLY CURRENT – mA
15
Figure 11. Output High Voltage, V OH
vs. Source Current
0
220.0
3
6
9
12
SOURCE CURRENT – mA
24.0
INPUT BIAS CURRENT – mA
0.3
0
I–, ANALOG SUPPLY CURRENT – mA
OUTPUT HIGH VOLTAGE – Volts
OUTPUT LOW VOLTAGE – Volts
0.5
1
10
FREQUENCY – MHz
100
Figure 14. Positive Supply Current
vs. Input Frequency
25
27.5
25
22.5
5
0
2.5
INPUT COMMON-MODE VOLTAGE – Volts
Figure 15. Input Bias Current vs. Input
Common-Mode Voltage for ± 5 V
Supplies
0
INPUT BIAS CURRENT – mA
21.0
22.0
23.0
24.0
25.0
275 250 225
0 25 50 75 100 125 150
TEMPERATURE – 8C
Figure 16. Input Bias Current vs.
Temperature
–6–
REV. A
AD8598
APPLICATIONS
Optimizing High Speed Performance
Note that signals much greater than +3.0 V will result in increased
input currents and may cause the device to operate more slowly.
As with any high speed comparator or amplifier, proper design
and layout techniques should be used to ensure optimal performance from the AD8598. The performance limits of high speed
circuitry can easily be a result of stray capacitance, improper
ground impedance or other layout issues.
The input bias current of the AD8598 is the same magnitude
(–3 µA typical) as the MAX912 (+3 µA typical), and the current flows out of the AD8598 and into MAX912. If relatively
low value resistors and/or low impedance sources are used on
the inputs, the voltage shift due to bias current should be small.
Minimizing resistance from source to the input is an important
consideration in maximizing the high speed operation of the
AD8598. Source resistance in combination with equivalent
input capacitance could cause a lagged response at the input,
thus delaying the output. The input capacitance of the AD8598,
in combination with stray capacitance from an input pin to
ground could result in several picofarads of equivalent capacitance. A combination of 3 kΩ source resistance and 5 pF of
input capacitance yields a time constant of 15 ns, which is
slower than the 5 ns capability of the AD8598. Source impedances should be less than 1 kΩ for the best performance.
The AD8598 (6.75 ns typical) is faster than the MAX912
(10 ns typical). While this is beneficial to many systems, timing
may need to be adjusted to take advantage of the higher speed.
The AD8598 has slightly more output voltage swing when the
output is lightly loaded.
The AD8598 uses less current (typically 10 mA) than the MAX912
(typically 12 mA).
Increasing Output Swing
Although not required for normal operation, the output voltage
swing of the AD8598 can be increased by connecting a 5 kΩ
resistor from the output of the device to the V+ power supply.
This configuration can be useful in low voltage power supply
applications where maximizing output voltage swing is important. Adding a 5 kΩ pull-up resistor to the device’s output will
not adversely affect the specifications of the AD8598.
It is also important to provide bypass capacitors for the power
supply in a high speed application. A 1 µF electrolytic bypass
capacitor should be placed within 0.5 inches of each power
supply pin to ground. These capacitors will reduce any potential
voltage ripples from the power supply. In addition, a 10 nF
ceramic capacitor should be placed as close as possible from the
power supply pins to ground. These capacitors act as a charge
reservoir for the device during high frequency switching.
Output Loading Considerations
The AD8598 output can deliver up to 40 mA of output current
without any significant increase in propagation delay. The
output of the device should not be connected to more than
twenty (20) TTL input logic gates, nor drive a load resistance
less than 100 Ω.
A ground plane is recommended for proper high speed performance. This can be created by using a continuous conductive
plane over the surface of the circuit board, only allowing breaks in
the plane for necessary current paths. The ground plane provides
a low inductance ground, eliminating any potential differences at
different ground points throughout the circuit board caused from
“ground bounce.” A proper ground plane also minimizes the
effects of stray capacitance on the circuit board.
To ensure the best performance from the AD8598 it is important to minimize capacitive loading of the output of the device.
Capacitive loads greater than 50 pF will cause ringing on the
output waveform and will reduce the operating bandwidth of
the comparator.
Replacing the MAX912
Setup and Hold Times for Latching the Output
The AD8598 is pin compatible with the MAX912 comparator.
While it is easy to replace the MAX912 with the higher performance AD8598, please note that there are differences, and it is
useful to check these to ensure proper operation.
The latch inputs can be used to retain data at the outputs of the
AD8598. When the voltage at the latch input goes high, the
output of the device will remain constant regardless of the input
voltages. The setup time for the latch is 2 ns–3 ns and the hold
time is 3 ns. This means that to ensure data retention at the
output, the input signal must be valid at least 5 ns before the
latch pin goes high and must remain valid at least 3 ns after the
latch pin goes high. Once the latch input voltage goes low, new
output data will appear in approximately 8 ns.
There are five major differences between the AD8598 and the
MAX912; input voltage range, input bias currents, speed, output swing and power consumption.
When operated on a +5 V single supply, the MAX912 has an
input voltage range from –0.2 V to +3.5 V. The AD8598 has an
input range from 0 V to +3.0 V. Signals above +3.0 V may
result in slower response times (see Figure 8). If both signals
exceed +3.0 V, the signals may be shifted or attenuated to bring
them into range, keeping in mind the note about source resistance in Optimizing High Speed Performance. If only one of the
signals exceeds +3.0 V only slightly, and the other signal is
always well within the 0 V to +3 V range, the comparator may
operate without changes to the circuit.
A logic high for the latch input is a minimum of +2.0 V and a
logic low is a maximum of +0.8 V. This makes the latch input
easily interface with TTL or CMOS logic gates. The latch
circuitry in the AD8598 has no built-in hysteresis.
Input Stage and Bias Currents
The AD8598 uses a PNP differential input stage that enables
the input common-mode range to extend all the way from the
negative supply rail to within +2.2 V of the positive supply rail.
The input common-mode voltage can be found as the average
of the voltage at the two inputs of the device. To ensure the
fastest response time, care should be taken not to allow the
input common-mode voltage to exceed either of these voltages.
Example: A comparator compares a fast moving signal to a fixed
+2.5 V reference. Since the comparator only needs to operate
when the signal is near +2.5 V, both signals will be within the
input range (near +2.5 V and well under +3.0 V) when the
comparator needs to change output.
REV. A
–7–
AD8598
The input bias current for the AD8598 is 3 µA. As with any
PNP differential input stage, this bias current will go to zero on
an input that is high and will double on an input that is low.
Care should be taken in choosing resistor values to be connected to the inputs as large resistors could cause significant
voltage drops due to the input bias current.
The input signal is directly connected to the noninverting input
of the comparator. The output is fed back to the inverting input
through R1 and R2. The ratio of R1 to R1 + R2 establishes the
width of the hysteresis window with VREF setting the center of
the window, or the average switching voltage. The Q output will
switch high when the input voltage is greater than VHI and will
not switch low again until the input voltage is less than VLO as
given in Equation 1:
The input capacitance for the AD8598 is typically 3 pF. This is
measured by inserting a 5 kΩ source resistance to the input and
measuring the change in propagation delay.
(
) R1+R1R2 +V
Using Hysteresis
V HI = V + –1–V REF
Hysteresis can easily be added to a comparator through the
addition of positive feedback. Adding hysteresis to a comparator
offers an advantage in noisy environments where it is not desirable for the output to toggle between states when the input
signal is near the switching threshold. Figure 17 shows a
method for configuring the AD8598 with hysteresis.

R1 
V LO =V REF 1–

 R1+ R2
SIGNAL
VREF
R1
REF
(1)
where V+ is the positive supply voltage.
The capacitor, CF, can also be added to introduce a pole into the
feedback network. This has the effect of increasing the amount of
hysteresis at high frequencies. This can be useful when comparing
a relatively slow signal in a high frequency noise environment. At
COMPARATOR
R2
1
, the hysteresis window
2π CF R2
approaches VHI = V+ – 1 V and VLO = 0 V. At frequencies less
than fP the threshold voltages remain as in Equation 1.
frequencies greater than fP =
CF
Figure 17. Configuring the AD8598 with Hysteresis
–8–
REV. A
AD8598
SPICE Model
* AD8598 SPICE Macro-Model Typical Values
* 4/98, Ver. 1.0
* TAM / ADSC
*
* Node assignments
*
non-inverting input
*
|
inverting input
*
|
|
positive supply
*
|
|
|
negative
*
|
|
|
|
*
|
|
|
|
*
|
|
|
|
*
|
|
|
|
*
|
|
|
|
.SUBCKT AD8598
1
2
99
50
*
* INPUT STAGE
*
*
Q1
4 3 5 PIX
Q2
6 2 5 PIX
IBIAS 99 5 800E-6
RC1
4 50 1E3
RC2
6 50 1E3
CL1
4 6 1E-12
CIN
1 2 3E-12
VCM1 99 7 1
D1
5 7 DX
EOS
3 1 POLY(1) (31,98) 1E-3 1
*
* Reference Voltage
*
EREF 98 0 POLY(2) (99,0) (50,0) 0 0.5 0.5
RREF 98 0 100E3
*
* CMRR=80dB, ZERO AT 1kHz
*
ECM1 30 98 POLY(2) (1,98) (2,98) 0 0.5 0.5
RCM1 30 31 10E3
RCM2 31 98 1
CCM1 30 31 15.9E-9
*
* Latch Section
*
RX 80 51 100E3
E1 10 98 (4,6) 1
S1 10 11 (80,51) SLATCH1
R2 11 12 1
C3 12 98 10E-12
E2 13 98 (12,98) 1
R3 12 13 500
*
* Power Supply Section
*
REV. A
–9–
supply
Latch
|
|
|
|
80
DGND
|
|
|
51
Q
|
|
45
QNOT
|
65
AD8598
GSY1 99 52 POLY(1) (99,50) 4E-3 -2.6E-4
GSY2 52 50 POLY(1) (99,50) 3.7E-3 -.6E-3
RSY 52 51 10
*
* Gain Stage Av=250 fp=100MHz
*
G2 98 20 (12,98) 0.25
R1 20 98 1000
C1 20 98 10E-13
D2 20 21 DX
D3 22 20 DX
V1 99 21 DC 0.8
V2 22 50 DC 0.8
*
* Q Output
*
Q3 99 41 46 NOX
Q4 47 42 50 NOX
RB1 43 41 200
RB2 40 42 5E3
CB1 99 41 10E-12
CB2 42 50 5E-12
RO1 46 45 2E3
RO2 47 45 500
EO1 98 43 POLY(1) (20,98) 0 1
EO2 40 98 POLY(1) (20,98) 0 1
*
* Q NOT Output
*
Q5 99 61 66 NOX
Q6 67 62 50 NOX
RB3 63 61 200
RB4 60 62 5E3
CB3 99 61 10E-12
CB4 62 50 5E-12
RO3 66 65 2E3
RO4 67 65 500
EO3 63 98 POLY(1) (20,98) 0 1
EO4 98 60 POLY(1) (20,98) 0 1
*
* MODELS
*
.MODEL PIX PNP(BF=100,IS=1E-16)
.MODEL NOX NPN(BF=100,VAF=130,IS=1E-14)
.MODEL DX D(IS=1E-16)
.MODEL SLATCH1 VSWITCH(ROFF=1E6,RON=500,VOFF=2.1,VON=1.4)
.ENDS AD8598
–10–
REV. A
AD8598
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
0.840 (21.33)
0.745 (18.93)
16
9
1
8
0.280 (7.11)
0.240 (6.10)
0.325 (8.25)
0.300 (7.62) 0.195 (4.95)
0.115 (2.93)
0.060 (1.52)
0.015 (0.38)
PIN 1
0.210 (5.33)
MAX
C3452a–8–10/98
16-Lead Plastic DIP
(N-16)
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
0.100
(2.54)
BSC
0.022 (0.558)
0.014 (0.356)
0.070 (1.77) SEATING
0.045 (1.15) PLANE
0.015 (0.381)
0.008 (0.204)
16-Lead Thin Shrink Small Outline
(RU-16)
0.201 (5.10)
0.193 (4.90)
16
9
0.256 (6.50)
0.246 (6.25)
0.177 (4.50)
0.169 (4.30)
1
0.006 (0.15)
0.002 (0.05)
SEATING
PLANE
8
PIN 1
0.0256
(0.65)
BSC
0.0433
(1.10)
MAX
0.0118 (0.30)
0.0075 (0.19)
0.0079 (0.20)
0.0035 (0.090)
88
08
0.028 (0.70)
0.020 (0.50)
16-Lead Narrow Body IC
(R-16A)
0.3937 (10.00)
0.3859 (9.80)
16
9
1
8
PIN 1
0.0098 (0.25)
0.0040 (0.10)
SEATING
PLANE
REV. A
0.0500
(1.27)
BSC
0.2440 (6.20)
0.2284 (5.80)
0.0688 (1.75)
0.0532 (1.35)
0.0196 (0.50)
3 458
0.0099 (0.25)
88
0.0192 (0.49)
08
0.0500 (1.27)
0.0099 (0.25)
0.0138 (0.35)
0.0160 (0.41)
0.0075 (0.19)
–11–
PRINTED IN U.S.A.
0.1574 (4.00)
0.1497 (3.80)