Tel : +44 118 979 1238 Fax : +44 118 979 1283 Email: [email protected] The ACTF9001/1220.0/QCC8B is a low-loss, compact and economical” surface wave acoustic” (SAW) RF filter in an SMD QCC8B package for Digital Set Top Box applications. 1.Package Dimension (QCC8B) 2. Pin Configuration 1,2 Input 5,6 Output 3,7 To be grounded 4,8 Case Ground Sign Data (unit: mm) Sign Data (unit: mm) A 1.00 D 1.50 B 1.27 E 3.80 C 0.60 F 3.80 3. Matching Circuit No matching network required for operation at 200 Ω In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered - Registration number 6830/2 For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com 1 OF 4 Issue : 1 C1 Date : SEPT 04 Tel : +44 118 979 1238 Fax : +44 118 979 1283 Email: [email protected] 4. Typical Frequency Response 5.Performance 5-1.Maximum ratings Rating Value Units Input Power Level 0 dBm DC Voltage 0 V Operable temperature range -40 to +85 °C Storage temperature range -40 to +85 °C In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered - Registration number 6830/2 For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com 2 OF 4 Issue : 1 C1 Date : SEPT 04 Tel : +44 118 979 1238 Fax : +44 118 979 1283 Email: [email protected] 5-2.Electronic characteristics Operating temperature range: Terminating source impedance: Terminating load impedance: T = -40 °c… +85 °c ZS= 200 Ω ZL = 200 Ω Characteristic Min. Centre Frequency fC Maximum insertion Loss (±4MHz) IL max Ripple in passband (±4MHz) Attenuation Group delay ripple Aperture 500 kHz Typ. 1220.0 ∆ α α rel 3.5 Units MHz 4.7 5.8 dB 0.8 1.5 dB 500.00 …. fc–91.00 MHz fc–91.00 …. f c–85.00 MHz 50.0 60.0 50.0 60.0 fc–76.00 …. f c–68.00 MHz 46.0 55.0 fc–88.00 MHz 50.0 60.0 fc–72.00 MHz 48.0 58.0 fc–44.00 MHz 50.0 60.0 fc–36.00 MHz 46.0 52.0 fc+70.00 …. 2000.00 MHz 50.0 55.0 ∆ Max. dB τ 1216.00 …… 1224.00 MHz 15 ns In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered - Registration number 6830/2 For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com 3 OF 4 Issue : 1 C1 Date : SEPT 04 Tel : +44 118 979 1238 Fax : +44 118 979 1283 Email: [email protected] 5-3.Electronic characteristics Operating temperature range: Terminating source impedance: Terminating load impedance: T = 20 °c … 70 °c ZS= 200 Ω ZL = 200 Ω Characteristic Min. Centre Frequency fC Minimum Insertion Loss Units MHz IL min 3.5 1210.00 …. 1229.00 MHz Relative attenuation ( relative to IL min) 4.5 5.8 dB 1.0 3.0 dB α ∆ Ripple in passband Aperture 500 kHz Max. 1220.0 1210.00 …. 1229.00 MHz Group delay ripple Typ. α rel 500.00 …. f C–91.00 MHz 46.0 56.0 fC–91.00 …. fC–85.00 MHz 46.0 56.0 fC–76.00 …. fC–68.00 MHz 42.0 51.0 fC–88.00 MHz 46.0 56.0 fC–72.00 MHz 44.0 54.0 fC–44.00 MHz 46.0 56.0 fC–36.00 MHz 42.0 48.0 fC +70.00 …. 2000.00 MHz 46.0 51.0 ∆ dB τ 1210.00 …… 1229.00 MHz 40 ns iCAUTION: Electrostatic Sensitive Device. Observe precautions for handling! 1. 2. 3. 4. 5. 6. The frequency f C is defined as the midpoint between the 3dB frequencies. Unless noted otherwise, all measurements are made with the filter installed in the specified test fixture that is connected to a 50 Ω test system with VSWR≤1.2:1. The test fixture L and C are adjusted for minimum insertion loss at the filter centre frequency, f C. Note that insertion loss, bandwidth, and passband shape are dependent on the impedance matching component values and quality. Unless noted otherwise, specifications apply over the entire specified operating temperature range. The specifications of this device are based on the test circuit shown above and subject to change or obsolescence without notice. All equipment designs utilizing this product must be approved by the appropriate government agency prior to manufacture or sale. Our liability is only assumed for the Surface Acoustic Wave (SAW) component(s) per se, not for applications, processes and circuits implemented within components or assemblies. In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice. ISO9001: 2000 Registered - Registration number 6830/2 For quotations or further information please contact us at: 3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK http://www.actcrystals.com 4 OF 4 Issue : 1 C1 Date : SEPT 04