TI1 LM140K-15/NOPB 3-terminal positive regulator Datasheet

LM140K
www.ti.com
SNVS994 – JULY 2013
LM140K 3-Terminal Positive Regulator
Check for Samples: LM140K
FEATURES
DESCRIPTION
•
•
•
•
•
•
The LM140K monolithic 3-terminal positive voltage
regulator employs internal current-limiting, thermal
shutdown and safe-area compensation, making them
essentially indestructible. If adequate heat sinking is
provided, they can deliver over 1.0A output current.
They are intended as fixed voltage regulators in a
wide range of applications including local (on-card)
regulation for elimination of noise and distribution
problems associated with single-point regulation. In
addition to use as fixed voltage regulators, these
devices can be used with external components to
obtain adjustable output voltages and currents.
1
2
Complete Specifications at 1A Load
Output Voltage Tolerances of ±4% at Tj = 25°C
Internal Thermal Overload Protection
Internal Short-circuit Current Limit
Output Transistor Safe Area Protection
P+ Product Enhancement Tested
Considerable effort was expended to make the entire
series of regulators easy to use and minimize the
number of external components. It is not necessary to
bypass the output, although this does improve
transient response. Input bypassing is needed only if
the regulator is located far from the filter capacitor of
the power supply.
The LM140K is available in 5V, 12V and 15V options
in the steel TO-3 power package.
Typical Applications
*Required if the regulator is located far from
the power supply filter.
**Although no output capacitor is needed
for stability, it does help transient response.
(If needed, use 0.1 μF, ceramic disc).
VOUT = 5V + (5V/R1 + IQ) R2 5V/R1 > 3 IQ,
load regulation (Lr) ≈ [(R1 + R2)/R1] (Lr of
LM140K-5.0).
Figure 2. Adjustable Output Regulator
Figure 1. Fixed Output Regulator
ΔIQ = 1.3 mA over line and load changes.
Figure 3. Current Regulator
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2013, Texas Instruments Incorporated
LM140K
SNVS994 – JULY 2013
www.ti.com
Connection Diagrams
Figure 4. TO-3 Metal Can (Bottom View)
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1) (2) (3)
DC Input Voltage
35V
Internal Power Dissipation (4)
Internally Limited
Maximum Junction Temperature
150°C
−65°C to +150°C
Storage Temperature Range
Lead Temperature (Soldering, 10 sec.)
TO-3 Package (NDS)
ESD Susceptibility (5)
(1)
(2)
(3)
(4)
(5)
300°C
2 kV
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Conditions are conditions under which
the device functions but the specifications might not be ensured. For ensured specifications and test conditions see the Electrical
Characteristics.
Specifications and availability for military grade LM140H/883 and LM140K/883 can be found in the LM140QML datasheet (SNVS382).
Specifications and availability for military and space grade LM140H/JAN and LM140K/JAN can be found in the LM140JAN datasheet
(SNVS399).
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
The maximum allowable power dissipation at any ambient temperature is a function of the maximum junction temperature for operation
(TJMAX = 125°C or 150°C), the junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA). PDMAX = (TJMAX −
TA)/θJA. If this dissipation is exceeded, the die temperature will rise above TJMAX and the electrical specifications do not apply. If the die
temperature rises above 150°C, the device will go into thermal shutdown. For the TO-3 package (NDS), the junction-to-ambient thermal
resistance (θJA) is 39°C/W. When using a heatsink, θJA is the sum of the 4°C/W junction-to-case thermal resistance (θJC) of the TO-3
package and the case-to-ambient thermal resistance of the heatsink.
ESD rating is based on the human body model, 100 pF discharged through 1.5 kΩ.
Operating Conditions (1)
Temperature Range (TA) (2)
(1)
(2)
2
LM140
−55°C to +125°C
Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Conditions are conditions under which
the device functions but the specifications might not be ensured. For ensured specifications and test conditions see the Electrical
Characteristics.
The maximum allowable power dissipation at any ambient temperature is a function of the maximum junction temperature for operation
(TJMAX = 125°C or 150°C), the junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA). PDMAX = (TJMAX −
TA)/θJA. If this dissipation is exceeded, the die temperature will rise above TJMAX and the electrical specifications do not apply. If the die
temperature rises above 150°C, the device will go into thermal shutdown. For the TO-3 package (NDS), the junction-to-ambient thermal
resistance (θJA) is 39°C/W. When using a heatsink, θJA is the sum of the 4°C/W junction-to-case thermal resistance (θJC) of the TO-3
package and the case-to-ambient thermal resistance of the heatsink.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM140K
LM140K
www.ti.com
SNVS994 – JULY 2013
LM140 Electrical Characteristics
55°C ≤ TJ ≤ + 150°C unless otherwise specified (1)
Output Voltage
Symbol
Input Voltage (unless otherwise noted)
Parameter
VO
5V
Output
Voltage
Conditions
10V
Line
Regulation
19V
Units
Max
Min
Typ
Max
Min
Typ
Max
TJ = 25°C, 5 mA ≤ IO ≤ 1A
4.9
5
5.1
11.75
12
12.25
14.7
15
15.3
V
PD ≤ 15W, 5 mA ≤ IO ≤ 1A
4.8
5.2
11.5
12.5
14.4
15.6
V
(7.5 ≤ VIN ≤ 20)
IO = 500 mA
TJ = 25°C, ΔVIN, −55°C ≤ TJ
≤ +150°C
(7.5 ≤ VIN ≤ 20)
3
10
4
5 mA ≤ IO ≤ 1.5A
10
250 mA ≤ IO ≤
750 mA
Over Temperature,
V
4
mV
(16 ≤ VIN ≤ 22)
25
12
22
(17.5 ≤ VIN ≤ 30)
30
(8 ≤ VIN ≤ 12)
mV
(17.9 ≤ VIN ≤ 30)
9
12
ΔVIN
V
22
18
(14.5 ≤ VIN ≤ 27)
4
Over Temperature
(17.9 ≤ VIN ≤ 30)
18
(14.8 ≤ VIN ≤ 27)
(7.5 ≤ VIN ≤ 20)
TJ = 25°C
TJ =
25°C
(14.8 ≤ VIN ≤ 27)
10
ΔVIN, −55°C ≤ TJ ≤ +150°C
Load
Regulation
23V
Typ
TJ = 25°C
ΔVO
15V
Min
VMIN ≤ VIN ≤ VMAX
ΔVO
12V
V
10
mV
30
mV
(20 ≤ VIN ≤ 26)
V
12
35
mV
32
15
19
21
mV
25
60
75
mV
5 mA ≤ IO ≤ 1A
IQ
ΔIQ
Quiescent
Current
TJ = 25°C
Quiescent
Current
Change
5 mA ≤ IO ≤ 1A
Over Temperature
6
6
mA
6.5
6.5
mA
0.5
TJ = 25°C, IO = 1A
0.5
0.5
0.8
VMIN ≤ VIN ≤ VMAX
(7.5 ≤ VIN ≤ 20)
IO = 500 mA
0.8
(14.8 ≤ VIN ≤ 27)
0.8
VMIN ≤ VIN ≤ VMAX
VN
6
6.5
TA = 25°C, 10 Hz ≤ f ≤ 100
kHz
Ripple
Rejection
TJ = 25°C, f = 120 Hz, IO =
1A
68
or f = 120 Hz, IO = 500 mA,
68
(15 ≤ VIN ≤ 30)
40
80
0.8
72
mA
(17.9 ≤ VIN ≤ 30)
V
90
μV
70
dB
60
61
V
0.8
75
61
mA
(17.9 ≤ VIN ≤ 30)
0.8
(8 ≤ VIN ≤ 25)
Output Noise
Voltage
mA
60
dB
Over Temperature,
VMIN ≤ VIN ≤ VMAX
RO
VIN
(1)
(18.5 ≤ VIN ≤ 28.5)
V
2.0
2.0
2.0
V
f = 1 kHz
8
18
19
mΩ
Short-Circuit
Current
TJ = 25°C
2.1
1.5
1.2
A
Peak Output
Current
TJ = 25°C
2.4
2.4
2.4
A
Average TC
of VO
Min, TJ = 0°C, IO = 5 mA
−0.6
−1.5
−1.8
mV/°C
Dropout
Voltage
TJ = 25°C, IO = 1A
Output
Resistance
Input Voltage TJ = 25°C
Required to
Maintain Line
Regulation
(8 ≤ VIN ≤ 18)
7.5
(15 ≤ VIN ≤ 25)
14.5
17.5
V
All characteristics are measured with a 0.22 μF capacitor from input to ground and a 0.1 μF capacitor from output to ground. All
characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tw ≤ 10 ms, duty cycle ≤ 5%).
Output voltage changes due to changes in internal temperature must be taken into account separately.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM140K
3
LM140K
SNVS994 – JULY 2013
www.ti.com
Typical Performance Characteristics
4
Maximum Average Power Dissipation
Output Voltage (Normalized to 1V at TJ = 25°C)
Figure 5.
Figure 6.
Ripple Rejection
Ripple Rejection
Figure 7.
Figure 8.
Output Impedance
Dropout Characteristics
Figure 9.
Figure 10.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM140K
LM140K
www.ti.com
SNVS994 – JULY 2013
Typical Performance Characteristics (continued)
Quiescent Current
Peak Output Current
Figure 11.
Figure 12.
Dropout Voltage
Quiescent Current
Figure 13.
Figure 14.
Line Regulation
140K, IOUT = 1A, TA = 25°C
Line Regulation
140K, VIN = 10V, TA = 25°C
Figure 15.
Figure 16.
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM140K
5
LM140K
SNVS994 – JULY 2013
www.ti.com
Equivalent Schematic
6
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM140K
LM140K
www.ti.com
SNVS994 – JULY 2013
APPLICATION HINTS
The LM140K is designed with thermal protection, output short-circuit protection and output transistor safe area
protection. However, as with any IC regulator, it becomes necessary to take precautions to assure that the
regulator is not inadvertently damaged. The following describes possible misapplications and methods to prevent
damage to the regulator.
SHORTING THE REGULATOR INPUT
When using large capacitors at the output of these regulators, a protection diode connected input to output
(Figure 17) may be required if the input is shorted to ground. Without the protection diode, an input short will
cause the input to rapidly approach ground potential, while the output remains near the initial VOUTbecause of the
stored charge in the large output capacitor. The capacitor will then discharge through a large internal input to
output diode and parasitic transistors. If the energy released by the capacitor is large enough, this diode, low
current metal and the regulator will be destroyed. The fast diode in Figure 17 will shunt most of the capacitors
discharge current around the regulator. Generally no protection diode is required for values of output capacitance
≤ 10 μF.
RAISING THE OUTPUT VOLTAGE ABOVE THE INPUT VOLTAGE
Since the output of the device does not sink current, forcing the output high can cause damage to internal low
current paths in a manner similar to that just described in the “Shorting the Regulator Input” section.
REGULATOR FLOATING GROUND (Figure 18)
When the ground pin alone becomes disconnected, the output approaches the unregulated input, causing
possible damage to other circuits connected to VOUT. If ground is reconnected with power “ON”, damage may
also occur to the regulator. This fault is most likely to occur when plugging in regulators or modules with on card
regulators into powered up sockets. Power should be turned off first, thermal limit ceases operating, or ground
should be connected first if power must be left on.
TRANSIENT VOLTAGES
If transients exceed the maximum rated input voltage of the device, or reach more than 0.8V below ground and
have sufficient energy, they will damage the regulator. The solution is to use a large input capacitor, a series
input breakdown diode, a choke, a transient suppressor or a combination of these.
Figure 17. Input Short
Figure 18. Regulator Floating Ground
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM140K
7
LM140K
SNVS994 – JULY 2013
www.ti.com
Figure 19. Transients
When a value for θ(H–A) is found using the equation shown, a heatsink must be selected that has a value that is
less than or equal to this number.
θ(H–A) is specified numerically by the heatsink manufacturer in this catalog, or shown in a curve that plots
temperature rise vs power dissipation for the heatsink.
Typical Applications
INPUT
OUTPUT
VI
VO
+
+
0.22 PF
0.1 PF
GND
Bypass capacitors are recommended for optimum stability and transient response, and should be located as close as
possible to the regulator.
Figure 20. Fixed Output Regulator
INPUT
OUTPUT
VI
VO
0.22 PF
8
GND
Submit Documentation Feedback
0.1 PF
(NOTE 1)
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM140K
LM140K
www.ti.com
SNVS994 – JULY 2013
INPUT
VI
OUTPUT
VO
GND
0.22 PF
0.1 PF
Figure 21. High Input Voltage Circuits
Q1
2N6133
IQ1
VI
R1
3.0:
IREG
OUTPUT
IO MAX
VO
INPUT
0.22 PF
0.1 PF
GND
Figure 22. High Current Voltage Regulator
RSC
Q1
2N6132
IN
Q2
2N6124
INPUT
OUT
R1
3.0:
OUTPUT
0.22 PF
GND
0.1 PF
Figure 23. High Output Current, Short Circuit Protected
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM140K
9
LM140K
SNVS994 – JULY 2013
www.ti.com
INPUT
OUTPUT
+
+ OUT
+
0.1 PF
GND
INPUT
OUTPUT
+
+
GND
0.1 PF
- OUT
Figure 24. Positive and Negative Regulator
10
Submit Documentation Feedback
Copyright © 2013, Texas Instruments Incorporated
Product Folder Links: LM140K
PACKAGE OPTION ADDENDUM
www.ti.com
26-Jul-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM140K-12
ACTIVE
TO-3
NDS
2
50
TBD
Call TI
Call TI
-55 to 125
LM140K
12P+
LM140K-12/NOPB
ACTIVE
TO-3
NDS
2
50
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
-55 to 125
LM140K
12P+
LM140K-15
ACTIVE
TO-3
NDS
2
50
TBD
Call TI
Call TI
-55 to 125
LM140K
15P+
LM140K-15/NOPB
ACTIVE
TO-3
NDS
2
50
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
-55 to 125
LM140K
15P+
LM140K-5.0
ACTIVE
TO-3
NDS
2
50
TBD
Call TI
Call TI
-55 to 125
LM140K
5.0P+
LM140K-5.0/NOPB
ACTIVE
TO-3
NDS
2
50
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
-55 to 125
LM140K
5.0P+
LM140KG-12 MD8
ACTIVE
DIESALE
Y
0
221
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
-55 to 125
LM140KG-5 MD8
ACTIVE
DIESALE
Y
0
221
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
-55 to 125
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
(4)
26-Jul-2016
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
NDS0002A
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated