ON MC10E431 5v ecl 3â bit differential flipâ flop Datasheet

MC10E431, MC100E431
5 V ECL 3‐Bit Differential
Flip‐Flop
Description
The MC10E/100E431 is a 3-bit flip-flop with differential clock,
data input and data output.
The asynchronous Set and Reset controls are edge-triggered rather
than level controlled. This allows the user to rapidly set or reset the
flip-flop and then continue clocking at the next clock edge, without the
necessity of de-asserting the set/reset signal (as would be the case with
a level controlled set/reset).
The E431 is also designed with larger internal swings, an approach
intended to minimize the time spent crossing the threshold region and
thus reduce the metastability susceptibility window.
The differential input structures are clamped so that the inputs of
unused registers can be left open without upsetting the bias network of
the device. The clamping action will assert the D and the CLK sides of
the inputs. Because of the edge triggered flip-flop nature of the device
simultaneously opening both the clock and data inputs will result in an
output which reaches an unidentified but valid state. Note that the
input clamps only operate when both inputs fall to 2.5 V below VCC.
The VBB pin, an internally generated voltage supply, is available to
this device only. For single-ended input conditions, the unused
differential input is connected to VBB as a switching reference voltage.
VBB may also rebias AC coupled inputs. When used, decouple VBB
and VCC via a 0.01 mF capacitor and limit current sourcing or sinking
to 0.5 mA. When not used, VBB should be left open.
The 100 Series contains temperature compensation.
Features
•
•
•
•
•
•
•
•
•
•
•
•
Edge-Triggered Asynchronous Set and Reset
Differential D, CLK and Q; VBB Reference Available
1100 MHz Min. Toggle Frequency
PECL Mode Operating Range: VCC = 4.2 V to 5.7 V
with VEE = 0 V
NECL Mode Operating Range: VCC = 0 V
with VEE = −4.2 V to −5.7 V
Internal Input 50 kW Pulldown Resistors
ESD Protection:
♦ > 2 kV Human Body Model
♦ > 200 V Machine Model
♦ > 2 kV Charged Device Model
Meets or Exceeds JEDEC Spec EIA/JESD78 IC
Latchup Test
Moisture Sensitivity: Level 3 (Pb-Free)
(For Additional Information, see Application Note AND8003/D)
Flammability Rating: UL 94 V−0 @ 0.125 in,
Oxygen Index: 28 to 34
Transistor Count = 348 Devices
These Devices are Pb-Free, Halogen Free and are RoHS Compliant
© Semiconductor Components Industries, LLC, 2016
July, 2016 − Rev. 11
1
www.onsemi.com
PLCC−28
FN SUFFIX
CASE 776−02
MARKING DIAGRAM*
1 28
MCxxxE431FNG
AWLYYWW
xxx
A
WL
YY
WW
G
= 10 or 100
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb-Free Package
*For additional marking information, refer to
Application Note AND8002/D.
ORDERING INFORMATION
Device
Package
Shipping†
MC10E431FNG
PLCC−28
(Pb-Free)
37 Units / Tube
MC10E431FNR2G
PLCC−28
(Pb-Free)
500 Tape & Reel
MC100E431FNR2G
PLCC−28
(Pb-Free)
500 Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer
to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
Publication Order Number:
MC10E431/D
MC10E431, MC100E431
VBB
CLK2 CLK2
25
24
23
D2
D2
R2
S2
22
21
20
19
Table 1. PIN DESCRIPTION
PIN
FUNCTION
CLK1
26
18
Q2
D[0:2], D[0:2]
ECL Differential Data Inputs
CLK1
27
17
Q2
CLK[0:2], CLK[0:2]
ECL Differential Clock
R1
16
VCC
S[0:2]
ECL Edge Triggered Set Inputs
28
R[0:2]
ECL Edge Triggered Reset Input
1
15
Q1
Q[0:2], Q[0:2]
ECL Differential Data Outputs
Q1
VBB
Reference Voltage Output
VCC, VCCO
Positive Supply
VEE
Negative Supply
VEE
MC10E431/MC100E431
S1
2
14
D1
3
13
Q0
D1
4
12
Q0
5
6
7
CLK0 CLK0 D0
8
9
10
D0
R0
S0
11
VCCO
* All VCC and VCCO pins are tied together on the die.
Warning: All VCC, VCCO, and VEE pins must be externally connected to Power Supply to guarantee proper operation.
Figure 1. Pinout: PLCC-28 (Top View)
S0
D0
D0
D
CLK0
CLK0
R0
S1
D1
D1
S
R
D
CLK1
CLK1
S
R
Q
Q0
Q
Q0
Q
Q1
Q
Q1
Q
Q2
Q
Q2
Table 2. FUNCTION TABLE
Dn
CLKn
Rn
Sn
L
Z
L
L
L
H
Z
L
L
H
X
X
Z
L
L
X
X
L
Z
H
Z = Low to high transition
X = Don’t Care
R1
S2
D2
D2
D
CLK2
CLK2
S
R
R2
VBB
Figure 2. Logic Diagram
www.onsemi.com
2
Qn
MC10E431, MC100E431
Table 3. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
VCC
PECL Mode Power Supply
VEE = 0 V
VI
PECL Mode Input Voltage
NECL Mode Input Voltage
VEE = 0 V
VCC = 0 V
Iout
Output Current
Continuous
Surge
IBB
VBB Sink/Source
TA
Operating Temperature Range
Tstg
Storage Temperature Range
qJA
Thermal Resistance (Junction-to-Ambient)
0 lfpm
500 lfpm
qJC
Thermal Resistance (Junction-to-Case)
Standard Board
Tsol
Wave Solder (Pb-Free)
Condition 2
Rating
Unit
8
V
6
−6
V
50
100
mA
±0.5
mA
0 to +85
°C
−65 to +150
°C
PLCC−28
PLCC−28
63.5
43.5
°C/W
PLCC−28
22 to 26
°C/W
265
°C
VI v VCC
VI w VEE
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
www.onsemi.com
3
MC10E431, MC100E431
Table 4. 10E SERIES PECL DC CHARACTERISTICS (VCCx= 5.0 V; VEE= 0.0 V (Note 1))
0°C
Symbol
Characteristic
Min
25°C
Typ
Max
110
132
Min
85°C
Typ
Max
110
132
Min
Typ
Max
Unit
110
132
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 2)
3980
4070
4160
4020
4105
4190
4090
4185
4280
mV
VOL
Output LOW Voltage (Note 2)
3050
3210
3370
3050
3210
3370
3050
3227
3405
mV
VIH
Input HIGH Voltage (Single-Ended)
3830
3995
4160
3870
4030
4190
3940
4110
4280
mV
VIL
Input LOW Voltage (Single-Ended)
3050
3285
3520
3050
3285
3520
3050
3302
3555
mV
VBB
Output Voltage Reference
3.62
3.74
3.65
3.75
3.69
3.81
V
Input HIGH Voltage Common Mode
Range (Differential Configuration) (Note 3)
2.7
5.0
2.7
5.0
2.7
5.0
V
150
mA
VIHCMR
IIH
Input HIGH Current
IIL
Input LOW Current
150
0.5
0.3
150
0.5
0.25
0.3
0.2
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification
limit values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.06 V.
2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
Table 5. 10E SERIES NECL DC CHARACTERISTICS (VCCx= 0.0 V; VEE= −5.0 V (Note 1)
0°C
Symbol
Characteristic
Min
25°C
Typ
Max
110
132
Min
85°C
Typ
Max
110
132
Min
Typ
Max
Unit
110
132
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 2)
−1020
−930
−840
−980
−895
−810
−910
−815
−720
mV
VOL
Output LOW Voltage (Note 2)
−1950
−1790
−1630
−1950
−1790
−1630
−1950
−1773
−1595
mV
VIH
Input HIGH Voltage (Single-Ended)
−1170
−1005
−840
−1130
−970
−810
−1060
−890
−720
mV
VIL
Input LOW Voltage (Single-Ended)
−1950
−1715
−1480
−1950
−1715
−1480
−1950
−1698
−1445
mV
VBB
Output Voltage Reference
−1.38
−1.27
−1.35
−1.25
−1.31
−1.19
V
Input HIGH Voltage Common Mode
Range (Differential Configuration) (Note 3)
−2.3
0.0
−2.3
0.0
−2.3
0.0
V
150
mA
VIHCMR
IIH
Input HIGH Current
IIL
Input LOW Current
150
0.5
0.3
150
0.5
0.065
0.3
0.2
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification
limit values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.06 V.
2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
www.onsemi.com
4
MC10E431, MC100E431
Table 6. 100E SERIES PECL DC CHARACTERISTICS (VCCx= 5.0 V; VEE= 0.0 V (Note 1))
0°C
Symbol
Characteristic
Min
25°C
Typ
Max
110
132
Min
85°C
Typ
Max
110
132
Min
Typ
Max
Unit
127
152
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 2)
3975
4050
4120
3975
4050
4120
3975
4050
4120
mV
VOL
Output LOW Voltage (Note 2)
3190
3295
3380
3190
3255
3380
3190
3260
3380
mV
VIH
Input HIGH Voltage (Single-Ended)
3835
3975
4120
3835
3975
4120
3835
3975
4120
mV
VIL
Input LOW Voltage (Single-Ended)
3190
3355
3525
3190
3355
3525
3190
3355
3525
mV
VBB
Output Voltage Reference
3.62
3.74
3.62
3.74
3.62
3.74
V
Input HIGH Voltage Common Mode Range
(Differential Configuration) (Note 3)
2.7
5.0
2.7
5.0
2.7
5.0
V
150
mA
VIHCMR
IIH
Input HIGH Current
IIL
Input LOW Current
150
0.5
0.3
150
0.5
0.25
0.5
0.2
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.8 V.
2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
Table 7. 100E SERIES NECL DC CHARACTERISTICS (VCCx= 0.0 V; VEE= −5.0 V (Note 1))
0°C
Symbol
Characteristic
Min
25°C
Typ
Max
110
132
Min
85°C
Typ
Max
110
132
Min
Typ
Max
Unit
127
152
mA
IEE
Power Supply Current
VOH
Output HIGH Voltage (Note 2)
−1025
−950
−880
−1025
−950
−880
−1025
−950
−880
mV
VOL
Output LOW Voltage (Note 2)
−1810
−1705
−1620
−1810
−1745
−1620
−1810
−1740
−1620
mV
VIH
Input HIGH Voltage (Single-Ended)
−1165
−1025
−880
−1165
−1025
−880
−1165
−1025
−880
mV
VIL
Input LOW Voltage (Single-Ended)
−1810
−1645
−1475
−1810
−1645
−1475
−1810
−1645
−1475
mV
VBB
Output Voltage Reference
−1.38
−1.26
−1.38
−1.26
−1.38
−1.26
V
Input HIGH Voltage Common Mode Range
(Differential Configuration) (Note 3)
−2.3
0.0
−2.3
0.0
−2.3
0.0
V
150
mA
VIHCMR
IIH
Input HIGH Current
IIL
Input LOW Current
150
0.5
0.3
150
0.5
0.25
0.5
0.2
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with VCC. VEE can vary −0.46 V / +0.8 V.
2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V.
3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.
www.onsemi.com
5
MC10E431, MC100E431
Table 8. AC CHARACTERISTICS (VCCx= 5.0 V; VEE= 0.0 V or VCCx= 0.0 V; VEE= −5.0 V (Note 1))
−40°C
Min
Characteristic
Symbol
Typ
fMAX
Maximum Toggle Frequency
tPLH
tPHL
Propagation Delay to Output
CLK
R
S
550
500
500
700
725
725
tS
Setup Time
D
R (Note 2)
S (Note 2)
250
1100
1100
tH
Hold Time
D
250
CLK
400
25°C
Max
Min
Typ
85°C
Max
Min
Typ
Max
1.1
550
550
550
700
725
725
0
700
700
200
1000
1000
0
200
tPW
Minimum Pulse Width
tskew
Within-Device Skew (Note 3)
50
tJITTER
Random Clock Jitter (RMS)
<1
VPP
Input Voltage Swing
(Differential Configuration)
150
tr/tf
Rise/Fall Times (20−80%)
250
850
975
975
850
925
925
550
550
550
700
725
725
0
700
700
200
1000
1000
0
700
700
0
200
0
400
450
700
150
850
925
925
1000
ps
ps
50
ps
<1
ps
150
275
ps
ps
400
<1
1000
Unit
GHz
450
1000
mV
650
ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification
limit values are applied individually under normal operating conditions and not valid simultaneously.
1. 10 Series: VEE can vary −0.46 V / +0.06 V.
100 Series: VEE can vary −0.46 V / +0.8 V.
2. These setup times define the minimum time the CLK or SET/RESET input must wait after the assertion of the RESET/SET input to assure
the proper operation of the flip-flop.
3. Within-device skew is defined as identical transitions on similar paths through a device.
www.onsemi.com
6
MC10E431, MC100E431
Q
Zo = 50 W
D
Receiver
Device
Driver
Device
Q
D
Zo = 50 W
50 W
50 W
VTT
VTT = VCC − 2.0 V
Figure 3. Typical Termination for Output Driver and Device Evaluation
(See Application Note AND8020/D − Termination of ECL Logic Devices)
Resource Reference of Application Notes
AN1405/D
− ECL Clock Distribution Techniques
AN1406/D
− Designing with PECL (ECL at +5.0 V)
AN1503/D
− ECLinPSt I/O SPiCE Modeling Kit
AN1504/D
− Metastability and the ECLinPS Family
AN1568/D
− Interfacing Between LVDS and ECL
AN1672/D
− The ECL Translator Guide
AND8001/D
− Odd Number Counters Design
AND8002/D
− Marking and Date Codes
AND8020/D
− Termination of ECL Logic Devices
AND8066/D
− Interfacing with ECLinPS
AND8090/D
− AC Characteristics of ECL Devices
www.onsemi.com
7
MC10E431, MC100E431
PACKAGE DIMENSIONS
28 LEAD PLLC
FN SUFFIX
CASE 776−02
ISSUE F
B
Y BRK
−N−
0.007 (0.180)
U
M
T L-M
0.007 (0.180)
M
N
S
T L-M
S
S
N
S
D
Z
−M−
−L−
W
28
D
X
V
1
G1
0.010 (0.250)
T L-M
S
N
S
S
VIEW D−D
Z
A
0.007 (0.180)
R
0.007 (0.180)
M
M
T L-M
S
T L-M
S
N
N
H
S
0.007 (0.180)
M
T L-M
N
S
S
S
K1
C
E
0.004 (0.100)
G
J
S
K
SEATING
PLANE
F
VIEW S
G1
0.010 (0.250)
−T−
T L-M
S
N
VIEW S
S
NOTES:
1. DATUMS -L-, -M-, AND -N- DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM -T-, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE
MOLD FLASH. ALLOWABLE MOLD FLASH IS
0.010 (0.250) PER SIDE.
4. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR
BURRS, GATE BURRS AND INTERLEAD
FLASH, BUT INCLUDING ANY MISMATCH
BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
INCHES
MIN
MAX
0.485
0.495
0.485
0.495
0.165
0.180
0.090
0.110
0.013
0.021
0.050 BSC
0.026
0.032
0.020
--0.025
--0.450
0.456
0.450
0.456
0.042
0.048
0.042
0.048
0.042
0.056
--0.020
2_
10_
0.410
0.430
0.040
---
www.onsemi.com
8
MILLIMETERS
MIN
MAX
12.32
12.57
12.32
12.57
4.20
4.57
2.29
2.79
0.33
0.53
1.27 BSC
0.66
0.81
0.51
--0.64
--11.43
11.58
11.43
11.58
1.07
1.21
1.07
1.21
1.07
1.42
--0.50
2_
10_
10.42
10.92
1.02
---
0.007 (0.180)
M
T L-M
S
N
S
MC10E431, MC100E431
ECLinPS is a trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC10E431/D
Similar pages