LP62S16256F-I Series Preliminary 256K X 16 BIT LOW VOLTAGE CMOS SRAM Document Title 256K X 16 BIT LOW VOLTAGE CMOS SRAM Revision History History Issue Date Remark 0.0 Initial issue November 22, 2002 Preliminary 0.1 Change ICC2 from 15mA to 8mA April 18, 2003 0.2 Modify 48LD CSP bottom view outline drawing May 5, 2003 0.3 Modify 48LD CSP outline dimensions November 19, 2003 0.4 Add Pb-Free package type August 9, 2004 Rev. No. PRELIMINARY (August, 2004, Version 0.4) AMIC Technology, Corp. LP62S16256F-I Series Preliminary 256K X 16 BIT LOW VOLTAGE CMOS SRAM Features General Description Operating voltage: 2.7V to 3.6V Access times: 55ns / 70ns (max.) Current: Very low power version: Operating: 40mA (max.) Standby: 10µA (max.) Full static operation, no clock or refreshing required All inputs and outputs are directly TTL-compatible Common I/O using three-state output Data retention voltage: 2.0V (min.) Available in 44-pin TSOP and 48-ball CSP (6 × 8mm) packages The LP62S16256F-I is a low operating current 4,194,304-bit static random access memory organized as 262,144 words by 16 bits and operates on low power voltage from 2.7V to 3.6V. It is built using AMIC's high performance CMOS process. Inputs and three-state outputs are TTL compatible and allow for direct interfacing with common system bus structures. The chip enable input is provided for POWER-DOWN, device enable. Two byte enable inputs and an output enable input are included for easy interfacing. Data retention is guaranteed at a power supply voltage as low as 2.0V. Product Family Power Dissipation Standby Operating Data Retention (ISB1, Typ.) (ICC2, Typ.) (ICCDR, Typ.) Product Family Operating Temperature VCC Range Speed LP62S16256F-I -40°C ~ +85°C 2.7V~3.6V 55ns / 70ns 0.08µA 44L TSOP 5mA 0.3µA Package Type 48B CSP 1. Typical values are measured at VCC = 3.0V, TA = 25°C and not 100% tested. 2. Data retention current VCC = 2.0V. Pin Configurations TSOP A4 1 44 A5 A3 2 43 A6 A2 3 42 A7 A1 4 41 OE 40 HB 39 LB 38 I/O16 37 I/O15 36 I/O14 35 I/O13 34 GND 33 VCC 32 I/O12 31 I/O11 30 I/O10 29 I/O9 28 NC 27 A8 A0 5 CE 6 I/O1 7 I/O2 8 I/O3 9 I/O4 10 VCC 11 GND 12 I/O5 13 I/O6 14 I/O7 15 I/O8 16 LP62S16256FV-I PRELIMINARY CSP (Chip Size Package) 48-pin Top View WE 17 A17 18 A16 19 26 A9 A15 20 25 A10 A14 21 24 A11 A13 22 23 A12 (August, 2004, Version 0.4) 1 1 2 3 4 5 6 A LB OE A0 A1 A2 NC B I/O9 HB A3 A4 CE I/O1 C I/O10 I/O11 A5 A6 I/O2 I/O3 D GND I/O12 A17 A7 I/O4 VCC E VCC I/O13 NC A16 I/O5 GND F I/O15 I/O14 A14 A15 I/O6 I/O7 G I/O16 NC A12 A13 WE I/O8 H NC A8 A9 A10 A11 NC AMIC Technology, Corp. LP62S16256F-I Series Block Diagram VCC A0 GND 512 X 8192 DECODER MEMORY ARRAY A16 A17 I/O1 I/O9 COLUMN I/O INPUT INPUT DATA CIRCUIT DATA CIRCUIT I/O16 I/O8 CE LB HB OE WE CONTROL CIRCUIT Pin Descriptions -- TSOP Pin No. Symbol 1 - 5, 18 - 27, 42 - 44 A0 - A17 6 CE 7 - 10, 13 - 16, 29 - 32, 35 - 38 I/O1 - I/O16 17 WE Write Enable Input 39 LB Lower Byte Enable Input (I/O1 to I/O8) 40 HB Higher Byte Enable Input (I/O9 to I/O16) 41 OE Output Enable Input 11, 33 VCC Power 12, 34 GND Ground 28 NC PRELIMINARY Description Address Inputs Chip Enable Input Data Inputs/Outputs No Connection (August, 2004, Version 0.4) 2 AMIC Technology, Corp. LP62S16256F-I Series Pin Description - CSP Symbol A0 - A17 CE Description Symbol Description Address Inputs HB Higher Byte Enable Input (I/O9 - I/O16) Chip Enable OE Output Enable I/O1 - I/O16 Data Input/Output VCC Power Supply WE Write Enable Input GND Ground LB Byte Enable Input (I/O1 - I/O8) NC No Connection Recommended DC Operating Conditions (TA = -40°C to + 85°C) Symbol Parameter Min. Typ. Max. Unit 2.7 3 3.6 V 0 0 0 V VCC Supply Voltage GND Ground VIH Input High Voltage 2.2 - VCC + 0.3 V VIL Input Low Voltage -0.3 - +0.6 V CL Output Load - - 30 pF TTL Output Load - - 1 - PRELIMINARY (August, 2004, Version 0.4) 3 AMIC Technology, Corp. LP62S16256F-I Series Absolute Maximum Ratings* *Comments VCC to GND .............................................. -0.5V to +4.0V IN, IN/OUT Volt to GND................... -0.5V to VCC + 0.5V Operating Temperature, Topr ...................-40°C to +85°C Storage Temperature, Tstg.....................-55°C to +125°C Power Dissipation, PT....................................................................... 0.7W Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to this device. These are stress ratings only. Functional operation of this device at these or any other conditions above those indicated in the operational sections of this specification is not implied or intended. Exposure to the absolute maximum rating conditions for extended periods may affect device reliability. DC Electrical Characteristics (TA = -40°C to + 85°C, VCC = 2.7V to 3.6V, GND = 0V) Symbol Parameter LP62S16256F-55LLI / 70LLI Unit Min. Typ. Max. - - 1 µA 1 µA Conditions ⏐ILI⏐ Input Leakage Current ⏐ILO⏐ Output Leakage Current - Active Power Supply Current - - 5 mA CE = VIL, II/O = 0mA - 25 40 mA Min. Cycle, Duty = 100% ICC ICC1 - VIN = GND to VCC CE = VIH HB = VIH or OE = VIH or WE = VIH VI/O = GND to VCC CE = VI, II/O = 0mA Dynamic Operating Current CE = VIL, VIH = VCC, VIL = 0V, f = 1MHz, II/O = 0 mA ICC2 - 5 8 mA ISB - - 1 mA CE = VIH VCC ≤ 3.3V - 0.3 10 µA CE ≥ VCC - 0.2V, VCC ≤ 3.3V VIN ≥ 0V ISB1 Standby Current VOL Output Low Voltage - - 0.4 V IOL = 2.1 mA VOH Output High Voltage 2.2 - - V IOH = -1.0 mA PRELIMINARY (August, 2004, Version 0.4) 4 AMIC Technology, Corp. LP62S16256F-I Series Truth Table I/O1 to I/O8 Mode I/O9 to I/O16 Mode VCC Current CE OE WE LB HB H X X X X Not selected Not selected ISB1, ISB X X X H H High - Z High - Z ISB1, ISB L L Read Read ICC1, ICC2, ICC L H Read High - Z ICC1, ICC2, ICC H L High - Z Read ICC1, ICC2, ICC L L Write Write ICC1, ICC2, ICC L H Write High - Z ICC1, ICC2, ICC H L High - Z Write ICC1, ICC2, ICC L L L X H L L H H L X High - Z High - Z ICC1, ICC2, ICC L H H X L High - Z High - Z ICC1, ICC2, ICC Note: X = H or L Capacitance (TA = 25°C, f = 1.0MHz) Symbol Parameter Min. Max. Unit Conditions CIN* Input Capacitance 6 pF VIN = 0V CI/O* Input/Output Capacitance 8 pF VI/O = 0V * These parameters are sampled and not 100% tested. PRELIMINARY (August, 2004, Version 0.4) 5 AMIC Technology, Corp. LP62S16256F-I Series AC Characteristics (TA = -40°C to +85°C, VCC = 2.7V to 3.6V) Symbol Parameter LP62S16256F-55LLI LP62S16256F-70LLI Unit Min. Max. Min. Max. 55 - 70 - ns Read Cycle tRC Read Cycle Time tAA Address Access Time - 55 - 70 ns tACE Chip Enable Access Time - 55 - 70 ns tBE Byte Enable Access Time - 55 - 70 ns tOE Output Enable to Output Valid - 30 - 35 ns tCLZ Chip Enable to Output in Low Z 10 - 10 - ns tBLZ Byte Enable to Output in Low Z 10 - 10 - ns tOLZ Output Enable to Output in Low Z 5 - 5 - ns tCHZ Chip Disable to Output in High Z - 20 - 25 ns tBHZ Byte Disable to Output in High Z - 20 - 25 ns tOHZ Output Disable to Output in High Z - 20 - 25 ns tOH Output Hold from Address Change 5 - 5 - ns tWC Write Cycle Time 55 - 70 - ns tCW Chip Enable to End of Write 50 - 60 - ns tBW Byte Enable to End of Write 50 - 60 - ns tAS Address Setup Time 0 - 0 - ns tAW Address Valid to End of Write 50 - 60 - ns tWP Write Pulse Width 40 - 50 - ns tWR Write Recovery Time 0 - 0 - ns tWHZ Write to Output in High Z - 25 - 25 ns tDW Data to Write Time Overlap 25 - 30 - ns tDH Data Hold from Write Time 0 - 0 - ns tOW Output Active from End of Write 5 - 5 - ns Write Cycle Note: tCHZ, tBHZ and tOHZ and tWHZ are defined as the time at which the outputs achieve the open circuit condition and are not referred to output voltage levels. PRELIMINARY (August, 2004, Version 0.4) 6 AMIC Technology, Corp. LP62S16256F-I Series Timing Waveforms Read Cycle 1(1, 2, 4) tRC Address tAA tOH tOH DOUT Read Cycle 2(1, 2, 3) tRC Address tAA CE tACE tCHZ5 tCLZ5 tBE HB, LB tBLZ5 tBHZ5 OE tOE tOHZ5 tOLZ5 DOUT Notes: 1. WE is high for Read Cycle. 2. Device is continuously enabled CE = VIL, HB = VIL and, or LB = VIL. 3. Address valid prior to or coincident with CE and ( HB and, or LB ) transition low. 4. OE = VIL. 5. Transition is measured ±500mV from steady state. This parameter is sampled and not 100% tested. PRELIMINARY (August, 2004, Version 0.4) 7 AMIC Technology, Corp. LP62S16256F-I Series Timing Waveforms (continued) Write Cycle 1 (Write Enable Controlled) tWC Address tWR3 tAW tCW CE tBW HB, LB tAS1 tWP2 WE tDH tDW DATA IN tWHZ4 tOW DATA OUT Write Cycle 2 (Chip Enable Controlled) tWC Address tAW tAS 1 tWR3 tCW2 CE tBW HB, LB tWP WE tDW tDH DATA IN tWHZ4 tOW DATA OUT PRELIMINARY (August, 2004, Version 0.4) 8 AMIC Technology, Corp. LP62S16256F-I Series Timing Waveforms (continued) Write Cycle 3 (Byte Enable Controlled) tWC Address tAW tCW CE tAS1 tWR3 tBW2 HB, LB tWP WE tDH tDW DATA IN tWHZ4 tOW DATA OUT Notes: 1. tAS is measured from the address valid to the beginning of Write. 2. A Write occurs during the overlap (tWP, tBW) of a low CE , WE and ( HB and , or LB ). 3. tWR is measured from the earliest of CE or WE or ( HB and , or LB ) going high to the end of the Write cycle. 4. OE level is high or low. 5. Transition is measured ±500mV from steady state. This parameter is sampled and not 100% tested. PRELIMINARY (August, 2004, Version 0.4) 9 AMIC Technology, Corp. LP62S16256F-I Series AC Test Conditions Input Pulse Levels 0.4V to 2.4V Input Rise And Fall Time 5 ns Input and Output Timing Reference Levels 1.5V Output Load See Figures 1 and 2 TTL TTL CL CL 30pF 5pF * Including scope and jig. * Including scope and jig. Figure 1. Output Load Figure 2. Output Load for tCLZ, tOLZ, tCHZ, tOHZ, tWHZ, and tOW Data Retention Characteristics (TA = -40°C to 85°C) Symbol Parameter Min. Typ. Max. Unit VDR VCC for Data Retention 2.0 - 3.6 V ICCDR Data Retention Current - 0.08 3* µA tCDR Chip Disable to Data Retention Time 0 - - ns tRC - - ns 5 - - ms tR Operation Recovery Time tVR VCC Rising Time from Data Retention Voltage to Operating Voltage * LP62S16256F-55LLI / 70LLI PRELIMINARY ICCDR: max. (August, 2004, Version 0.4) Conditions CE ≥ VCC - 0.2V VCC = 2.0V, CE ≥ VCC - 0.2V VIN ≥ 0V See Retention Waveform 1µA at TA = 0°C to + 40°C 10 AMIC Technology, Corp. LP62S16256F-I Series Low VCC Data Retention Waveform DATA RETENTION MODE 2.7V 2.7V VCC tCDR tR VDR ≥ 2.0V tVR VIH CE VIH CE ≥ VDR - 0.2V Ordering Information Part No. Access Time (ns) Operating Current Max. (mA) Standby Current Max. (µA) LP62S16256FV-55LLI Package 44L TSOP LP62S16256FV-55LLIF 44L Pb-Free TSOP 55 40 10 LP62S16256FU-55LLI 48L CSP LP62S16256FU-55LLIF 48L Pb-Free CSP LP62S16256FV-70LLI 44L TSOP LP62S16256FV-70LLIF 44L Pb-Free TSOP 70 40 10 LP62S16256FU-70LLI 48L CSP LP62S16256FU-70LLIF 48L Pb-Free CSP PRELIMINARY (August, 2004, Version 0.4) 11 AMIC Technology, Corp. LP62S16256F-I Series Package Information TSOP 44L TYPE II Outline Dimensions unit: inches/mm HE 0.254 23 E 44 L L1 1 22 B e D S Symbol y A L1 L A1 A2 c D Dimension in inch Dimension in mm Min. Nom. Max. Min. Nom. Max. A - - 0.047 - - 1.20 A1 0.002 - - 0.05 - - A2 0.037 0.039 0.041 0.95 1.00 1.05 B 0.010 0.014 0.018 0.25 0.35 0.45 c - 0.006 - - 0.15 - D 0.721 0.725 0.729 18.31 18.41 18.51 E 0.396 0.400 0.404 10.06 10.16 10.26 e - 0.031 - - 0.80 - HE 0.455 0.463 0.471 11.56 11.76 11.96 L 0.016 0.020 0.024 0.40 0.50 0.60 L1 - 0.031 - - 0.80 - S - - 0.036 - - 0.93 y - - 0.004 - - 0.10 θ 0° - 5° 0° - 5° Notes: 1. Dimension D&E do not include interlead flash. 2. Dimension B does not include dambar protrusion/intrusion. 3. Dimension S includes end flash. PRELIMINARY (August, 2004, Version 0.4) 12 AMIC Technology, Corp. LP62S16256F-I Series Package Information 48LD CSP ( 6 x 8 mm ) Outline Dimensions unit: mm (48TFBGA) TOP VIEW BOTTOM VIEW Ball#A1 CORNER 0.10 S C 0.25 S C A B Ball*A1 CORNER b (48X) 6 5 4 3 2 1 1 2 3 4 5 6 A B C D E F G H E E1 e A B C D E F G H B A 0.10 C SIDE VIEW D 0.20(4X) A2 SEATING PLANE A1 (0.36) C Symbol A A1 A2 D E D1 E1 e b A // 0.25 C e D1 Dimensions in mm MIN. NOM. MAX. 1.00 0.20 0.48 5.90 7.90 ------0.30 1.10 0.25 0.53 6.00 8.00 3.75 5.25 0.75 0.35 1.20 0.30 0.58 6.10 8.10 ------0.40 Note: 1. THE BALL DIAMETER, BALL PITCH, STAND-OFF & PACKAGE THICKNESS ARE DIFFERENT FROM JEDEC SPEC MO192 (LOW PROFILE BGA FAMILY). 2. PRIMARY DATUM C AND SEATING PLANE ARE DEFINED BY THE SPHERICAL CROWNS OF THE SOLDER BALLS. 3. DIMENSION b IS MEASURED AT THE MAXIMUM. THERE SHALL BE A MINIMUM CLEARANCE OF 0.25mm BETWEEN THE EDGE OF THE SOLDER BALL AND THE BODY EDGE. 4. BALL PAD OPENING OF SUBSTRATE IS Φ 0.3mm (SMD) SUGGEST TO DESIGN THE PCB LAND SIZE AS Φ 0.3mm (NSMD) PRELIMINARY (August, 2004, Version 0.4) 13 AMIC Technology, Corp.