Document 536-1 Shielded Power Inductors–LPS5010 Series • Very low DCR; excellent current handling • 5.0 × 5.0 mm footprint; less than 1.0 mm tall Designer’s Kit C407 contains 3 each of all values Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 70 – 75 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 1000/7″reel; 3000/13″ reel Plastic tape: 12 mm wide, 0.3 mm thick, 8 mm pocket spacing, 1.02 mm pocket depth Recommended pick and place nozzle OD: 5 mm; ID: ≤ 2.5 mm PCB washing Only pure water or alcohol recommended DCR SRF max3 typ4 ±20% (µH) (Ohms) (MHz) Inductance2 Part number1 LPS5010-471ML_ LPS5010-821ML_ LPS5010-152ML_ LPS5010-222ML_ LPS5010-332ML_ LPS5010-472ML_ LPS5010-562ML_ LPS5010-682ML_ LPS5010-103ML_ LPS5010-153ML_ 0.47 0.82 1.5 2.2 3.3 4.7 5.6 6.8 10 15 Isat (A)5 10% 20% 30% drop drop drop Irms (A)6 20°C 40°C rise rise 0.038 0.058 0.072 0.100 0.125 290 195 168 144 105 3.1 2.3 1.7 1.4 1.1 3.3 2.5 1.8 1.5 1.2 3.4 2.6 1.9 1.6 1.3 2.0 1.2 0.90 0.88 0.86 2.7 1.5 1.4 1.2 1.1 0.175 0.240 0.255 0.350 0.500 76 75 71 51 39 0.95 0.90 0.82 0.66 0.55 1.1 0.97 0.90 0.72 0.59 1.1 1.00 0.93 0.74 0.62 0.85 0.75 0.74 0.73 0.68 0.98 0.92 0.85 0.80 0.75 0.670 1.05 1.45 2.00 3.10 32 26 20 15 12 0.47 0.38 0.31 0.26 0.21 0.51 0.42 0.34 0.29 0.23 0.53 0.43 0.36 0.30 0.24 0.46 0.40 0.33 0.25 0.21 0.62 0.55 0.44 0.35 0.28 11 9.0 7.0 5.5 4.5 0.20 0.18 0.15 0.12 0.090 0.22 0.20 0.16 0.13 0.11 0.23 0.21 0.17 0.14 0.11 0.19 0.17 0.15 0.13 0.11 0.25 0.23 0.20 0.185 0.150 LPS5010-223ML_ LPS5010-333ML_ LPS5010-473ML_ LPS5010-683ML_ LPS5010-104ML_ 22 33 47 68 100 LPS5010-124ML_ LPS5010-154ML_ LPS5010-224ML_ LPS5010-334ML_ LPS5010-474ML_ 120 150 220 330 470 3.50 4.25 6.25 8.60 12.7 LPS5010-564ML_ LPS5010-684ML_ LPS5010-105ML_ 560 680 1000 15.7 20.0 28.0 4.0 0.090 0.10 0.10 3.7 0.090 0.097 0.10 3.0 0.087 0.096 0.10 0.10 0.135 0.090 0.125 0.080 0.110 1. Please specify termination and packaging codes: LPS5010-105MLC Termination: L = RoHS compliant silver-palladiumplatinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: C= 7″ machine-ready reel. EIA-481 embossed plastic tape (1000 parts per full reel). B= Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D= 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (3500 parts per full reel). 2. Inductance tested at 100 kHz, 0.1 Vrms using an Agilent/HP 4192A. Inductance at 1 MHz is the same for parts with SRF ≥10 MHz. 3. DCR measured on a micro-ohmmeter. 4. SRF measured using Agilent/HP 8753ES or equivalent. 5. DC current that causes the specified inductance drop from its value without current. 6. Current that causes the specified temperature rise from 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 Document 536-1 Revised 10/06/08 Document 536-2 Shielded SMT Power Inductors – LPS5010 Series Typical L vs Current Typical L vs Frequency 10000 10000 1000 µH 100 100 µH 10 10 µH 1 0.1 1 0.1 100 µH 100 10 µH 10 0.82 µH 1 0.82 µH 0.01 1000 µH 1000 Inductance (µH) Inductance (µH) 1000 10 0.1 0.01 10 Frequency (MHz) 0.189 ±0.003* 4,80 ±0,076 Current Derating 120 110 100 0.189 ±0.003* 4,80 ±0,076 XXX X 90 80 70 Dash number 60 Winding direction Internal code Recommended Land Pattern 50 40 30 20 25°C Percent of rated current 1 0.1 Current (A) Isat Irms 10 0 -40 -20 0 20 0.060 1,50 40 60 80 100 0.138 3,50 0.090 2,30 0.0354 ±0.004 0,90 ±0,10 45° typ 120 140 Ambient temperature (°C) 0.039 typ 1,00 0.039 typ 1,00 are of the case not * Dimensions including the termination. For maximum overall dimensions including the termination, add 0.005 in / 0,13 mm. Dimensions are in 0.060 1,50 0.134 3,40 0.197 5,00 inches mm Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 0.197 5,00 0.134 0.090 3,40 2,30 Document 536-2 Revised 10/06/08