ON MC10H141 Four-bit universal shift register Datasheet

 SEMICONDUCTOR TECHNICAL DATA
The MC10H141 is a four–bit universal shift register. This device is a
functional/pinout duplication of the standard MECL 10K part with 100%
improvement in propagation delay and operation frequency and no increase in
power supply current.
L SUFFIX
CERAMIC PACKAGE
CASE 620–10
• Shift frequency, 250 MHz Min
• Power Dissipation, 425 mW Typical
• Improved Noise Margin 150 mV (over operating voltage and
temperature range)
• Voltage Compensated
• MECL 10K–Compatible
P SUFFIX
PLASTIC PACKAGE
CASE 648–08
FN SUFFIX
PLCC
CASE 775–02
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
VEE
VI
–8.0 to 0
Vdc
0 to VEE
Vdc
Power Supply (VCC = 0)
Input Voltage (VCC = 0)
Output Current — Continuous
— Surge
Iout
50
100
mA
Operating Temperature Range
TA
Tstg
0 to +75
°C
–55 to +150
–55 to +165
°C
°C
Storage Temperature Range — Plastic
— Ceramic
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%)
0°
25°
75°
Symbol
Min
Max
Min
Max
Min
Max
Unit
Power Supply Current
IE
IinH
—
112
—
102
—
112
mA
Input Current Low
High Output Voltage
Low Output Voltage
High Input Voltage
Low Input Voltage
IinL
VOH
VOL
VIH
VIL
S1 S2
L
L Parallel Entry
L
H
Shift Right*
H
L
Shift Left*
H
H
Stop Shift
—
—
—
405
416
510
—
—
—
255
260
320
—
—
—
0.5
—
0.5
—
0.3
Hold Time —
Data, Select
Set–up Time
Data
Select
Rise Time
Fall Time
Shift Frequency
tpd
thold
255
260
320
D1
D2
D3
Q2n
Q3n
DR
DL
Q0n
Q1n
Q2n
Q0n
Q1n
Q2n
32n
VCC1
1
16
VCC2
—
µA
Q2
2
15
Q1
–1.02 –0.84 –0.98 –0.81 –0.92
–0.735
Vdc
Q3
3
14
Q0
–1.95 –1.63 –1.95 –1.63 –1.95
–1.60
Vdc
–1.17 –0.84 –1.13 –0.81 –1.07
–0.735
Vdc
C
4
13
DL
–1.95 –1.48 –1.95 –1.48 –1.95
–1.45
Vdc
DR
5
12
D0
D3
6
11
D1
S2
7
10
S1
VEE
8
9
D2
1.0
2.0
1.0
2.0
1.1
2.1
ns
1.0
—
1.0
—
1.0
—
ns
1.5
3.0
—
—
1.5
3.0
—
—
1.5
3.0
—
—
tr
tf
0.5
2.4
0.5
2.4
0.5
2.4
0.5
2.4
0.5
2.4
0.5
2.4
ns
fshift
250
—
250
—
250
—
MHz
tset
ns
ns
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
NOTE:
Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit
board and transverse air flow greater than 500 Iinear fpm is maintained. Outputs are terminated through
a 50 ohm resistor to –2.0 volts.
9/96
 Motorola, Inc. 1996
D0
Q1n
DIP
PIN ASSIGNMENT
µA
AC PARAMETERS
Propagation Delay
OUTPUTS
OPERATING
Q1
Q0
MODE
n + 1 Q2n + 1 Q3n + 1
n+1
* Outputs as exist after pulse appears at “C” input with
input conditions as shown (Pulse Positive transition of
clock input).
Characteristic
Input Current High
Pins 5,6,9,11,12,13
Pins 7,10
Pin 4
TRUTH TABLE
SELECT
2–131
REV 6
MC10H141
LOGIC DIAGRAM
D3
D2
D1
D0
PARALLEL ENTER
S1
1 OF 4
DECODER
S2
SHIFT RIGHT
DR
SHIFT LEFT
DL
HOLD
D Q
D Q
D Q
D Q
C
C
C
C
C
Q3
Q2
Q1
Q0
VCC1 = PIN 1
SCC2 = PIN 16
VEE = PIN 8
APPLICATION INFORMATION
information on the positive edge of the clock. The
four operations are stop shift, shift left, shift right, and
parallel entry of data. The other six inputs are all data
type inputs; four for parallel entry data, and one for
shifting in from the left (DL) and one for shifting in
from the right (DR).
The MC10H141 is a four–bit universal shift
register which performs shift left, or shift right,
serial/parallel in, and serial/parallel out operations
with no external gating. Inputs S1 and S2 control the
four possible operations of the register without
external gating of the clock. The flip–flops shift
MOTOROLA
2–132
MECL Data
DL122 — Rev 6
MC10H141
OUTLINE DIMENSIONS
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 775–02
ISSUE C
0.007 (0.180) M T L–M
B
Y BRK
–N–
U
N
S
0.007 (0.180) M T L–M
S
S
N
S
D
–L–
–M–
Z
W
20
D
1
V
0.010 (0.250)
G1
X
S
T L–M
S
N
S
VIEW D–D
A
0.007 (0.180) M T L–M
S
N
S
R
0.007 (0.180) M T L–M
S
N
S
Z
C
H
–T–
SEATING
PLANE
F
VIEW S
G1
0.010 (0.250) S T L–M
S
0.007 (0.180)
M
T L–M
S
N
S
VIEW S
S
N
S
NOTES:
1. DATUMS –L–, –M–, AND –N– DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS PLASTIC
BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM –T–, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE MOLD
FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250)
PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN THE
PACKAGE BOTTOM BY UP TO 0.012 (0.300).
DIMENSIONS R AND U ARE DETERMINED AT THE
OUTERMOST EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,
GATE BURRS AND INTERLEAD FLASH, BUT
INCLUDING ANY MISMATCH BETWEEN THE TOP
AND BOTTOM OF THE PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037 (0.940).
THE DAMBAR INTRUSION(S) SHALL NOT CAUSE
THE H DIMENSION TO BE SMALLER THAN 0.025
(0.635).
MECL Data
DL122 — Rev 6
N
K
0.004 (0.100)
J
S
K1
E
G
0.007 (0.180) M T L–M
2–133
DIM
A
B
C
E
F
G
H
J
K
R
U
V
W
X
Y
Z
G1
K1
INCHES
MIN
MAX
0.385
0.395
0.385
0.395
0.165
0.180
0.090
0.110
0.013
0.019
0.050 BSC
0.026
0.032
0.020
–––
0.025
–––
0.350
0.356
0.350
0.356
0.042
0.048
0.042
0.048
0.042
0.056
–––
0.020
2_
10 _
0.310
0.330
0.040
–––
MILLIMETERS
MIN
MAX
9.78
10.03
9.78
10.03
4.20
4.57
2.29
2.79
0.33
0.48
1.27 BSC
0.66
0.81
0.51
–––
0.64
–––
8.89
9.04
8.89
9.04
1.07
1.21
1.07
1.21
1.07
1.42
–––
0.50
2_
10 _
7.88
8.38
1.02
–––
MOTOROLA
MC10H141
OUTLINE DIMENSIONS
L SUFFIX
CERAMIC DIP PACKAGE
CASE 620–10
ISSUE V
–A–
16
9
1
8
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
4. DIMENSION F MAY NARROW TO 0.76 (0.030)
WHERE THE LEAD ENTERS THE CERAMIC
BODY.
–B–
C
L
DIM
A
B
C
D
E
F
G
H
K
L
M
N
–T–
K
N
SEATING
PLANE
M
E
F
J
G
D
16 PL
0.25 (0.010)
16 PL
0.25 (0.010)
M
T A
T B
M
–A–
9
1
8
B
F
C
L
S
–T–
SEATING
PLANE
K
H
G
D
M
J
16 PL
0.25 (0.010)
M
MILLIMETERS
MIN
MAX
19.05
19.93
6.10
7.49
–––
5.08
0.39
0.50
1.27 BSC
1.40
1.65
2.54 BSC
0.21
0.38
3.18
4.31
7.62 BSC
0_
15 _
0.51
1.01
S
P SUFFIX
PLASTIC DIP PACKAGE
CASE 648–08
ISSUE R
16
S
INCHES
MIN
MAX
0.750
0.785
0.240
0.295
–––
0.200
0.015
0.020
0.050 BSC
0.055
0.065
0.100 BSC
0.008
0.015
0.125
0.170
0.300 BSC
0_
15 _
0.020
0.040
T A
M
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
DIM
A
B
C
D
F
G
H
J
K
L
M
S
INCHES
MIN
MAX
0.740
0.770
0.250
0.270
0.145
0.175
0.015
0.021
0.040
0.70
0.100 BSC
0.050 BSC
0.008
0.015
0.110
0.130
0.295
0.305
0_
10 _
0.020
0.040
MILLIMETERS
MIN
MAX
18.80
19.55
6.35
6.85
3.69
4.44
0.39
0.53
1.02
1.77
2.54 BSC
1.27 BSC
0.21
0.38
2.80
3.30
7.50
7.74
0_
10 _
0.51
1.01
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
MFAX: [email protected] – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
◊
MOTOROLA
2–134
*MC10H141/D*
MC10H141/D
MECL Data
DL122 — Rev 6
Similar pages