LE200S-CD 200W Single Output LED Driver Series Features High Efficiency (up to 93%) Wide Range Universal Input 90-305 VAC Active Power Factor Correction (0.99 typical) Constant Current Output Dimming Function Lightning Protection Waterproof (IP67) Overcurrent, Overvoltage, Overtemperature Protection Meets UL8750 & EN61347 Safety 3 Year Warranty Description The LE200S-CD Series operate from a 90 ~ 305Vac input range. These units will provide up to a 0.7A of output current and a maximum output voltage of 285Vdc for 200 W maximum output power. They are designed to be highly efficient and highly reliable. The standard features include dimming control, lightning protection, over voltage protection, short circuit protection, and over temperature protection. Model Selection Model Number Output Current Output Voltage LE200S70CD 665mA-735mA 143V – 285V Notes: Efficiency* 110Vac 220Vac 90%-91% 92%-93% Ripple & Noise** Regulation Line Load 8.6V pk-pk max. ±1% ±3% Overvoltage Trip Level 342V – 428V 1. Efficiency measured at full load, at input voltage noted. 2. Measured at 20MHz bandwidth, with noise probe directly across output terminals, and load terminated with 0.1µF ceramic and 10µF low ESR electrolytic capacitors. General Specifications AC Input Input Current Inrush Current Input Fuses www.slpower.com Turn On Time 90-305Vac, 47-63Hz, 1∅ 100Vac: 2.4A, 220Vac: 1.2A 230Vac, cold start: will not exceed 65A Overload Protection Dimming Function 1.0 seconds, max. Constant Current 1-10Vdc source or External Resistor can be used for dimming control. See below. XA, 250VAC fuses provided on all models LE200S-CD REV 2.0,11-FEB-13 1 LE200S-CD 200W Single Output LED Driver Series General Specifications (continued) Earth Leakage Current Efficiency Output Power Short Circuit Protection <0.75mA@277Vac, 50Hz See Models chart. 200W continuous Provided - no damage to unit, self-recovery. Overvoltage Protection Latch mode. AC input will need to be reset to return to normal operation after an OVP condition. See chart for trip range. Overtemperature Protection Latch mode. AC input will need to be reset to return to normal operation after an OTP condition. Trip Temperature = 110°C typical. Ripple and Noise See chart Operating Temperature Output Voltage See chart Relative Humidity 10% to 100% operating 5% to 100%, non-operating +/- 3%. See chart Safety Standards UL8750, UL935, UL1012, CSA-C22.2 No. 107.1, EN61347-1, EN61347-2-13 Total Regulation Dimensions Weight MTBF 330,000 hours (450mA model, 110Vac input, 80% load, 25°C ambient, per MIL-HDBK-217F). Lifetime 90,000 hours (1400mA model, at 110Vac input, 80% load, 45°C ambient temperature). W: 3.13” x L: 9.37” x H: 1.81” 1500g Operating: -35°C to +70°C Non-operating: -40°C to +85°C EMI/EMC Compliance Emissions EN55015, Radiated & Conducted with 6db of margin EMI for Lighting Equipment EN61547 Static Discharge Immunity EN61000-4-2, 4kV Contact Discharge, 8kV air discharge Radiated RF Immunity EN61000-4-3 EFT/Burst Immunity EN61000-4-4 Line Surge Immunity EN61000-4-5, 4kV line-line, 6kV line-earth Conducted RF Immunity EN61000-4-6 Power Frequency Magnetic Field Immunity EN61000-4-8 Voltage Dip Immunity EN61000-4-11 Line Harmonic Emissions EN61000-3-2 Flicker Test EN61000-3-3 www.slpower.com LE200S-CD REV 2.0,11-FEB-13 2 LE200S-CD 200W Single Output LED Driver Series Derating Curves Mechanical Drawing www.slpower.com LE200S-CD REV 2.0,11-FEB-13 3 LE200S-CD 200W Single Output LED Driver Series Dimming Control The dimmer control may be operated from either a potentiometer or from an input signal of 1 – 10 Vdc. Two recommended implementations are provided below. Parameters: Parameter Min. Typ. Max. Absolute Max. Voltage on the 1-10V input -2V - 12V Sink Current on the 1-10V input pin 0mA - 1mA Notes LE200SXXXCD Dimming Configuration using External Voltage LE150SXXXCD Dimming Configuration using External Resistance Dimming Control Notes: 1. Io is actual output current and Ir is rated current without dimming control. 2. For the driver to operate properly, the load voltage must be maintained above the minimum voltage threshold (approx. 50% of the max. output voltage for any given model). 3. If the output voltage is maintained above 50% of the maximum output voltage, the dimming control may be operated over the entire 1-10V range with output current varying from 100% down to practically 10%. 4. The dimming signal is allowed to be less than 1V, however, when it for 0-1V, the output current is 10%Io. 5. Do not connect the GND of dimming to the output; otherwise, the LED driver can not work normally. Data Sheet © 2012 SL Power Electronics Corp. The information and specifications contained herein are believed to be correct at the time of publication. However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice. www.slpower.com LE200S-CD REV 2.0,11-FEB-13 4