UNISONIC TECHNOLOGIES CO., LTD LR1108 CMOS IC 1A FAST ULTRA LOW DROPOUT LINEAR REGULATOR DESCRIPTION The UTC LR1108 operate from a +2.5V ~ +7.0V input supply as fast ultra low-dropout linear regulators. Wide output voltage range options are available. The fast response characteristic to make UTC LR1108 suitable for low voltage microprocessor application. The low quiescent current operation and low dropout quality caused by the CMOS process. The UTC LR1108 has ultra low dropout voltage; 300mV at 1A load current typically. The ground pin current is typically 200uA at 1mA load current. ERROR Flag: When the output voltage drops 10% below nominal value Error flag goes low. Output Voltage Precision: Multiple output voltage options are available and ranging from 1.2V ~ 5.0V at room temperature with a guaranteed accuracy of ±1.5%, and ±3.0% when varying line, load and temperature. FEATURES * Ultra Low Dropout Voltage * Low Ground Pin Current * 0.04% Load Regulation * The Guaranteed Output Current is 1A DC * Output Voltage Accuracy ± 1.5% * ERROR Flag Indicates Output Status * Low Output Capacitor Required * Over temperature Protection And Over current Protection ORDERING INFORMATION Ordering Number Lead Free Halogen Free LR1108L-xx-AA3-c-R LR1108G-xx-AA3-c-R LR1108L-xx-AB3-c-R LR1108G-xx-AB3-c-R LR1108L-xx-TN3-c-R LR1108G-xx-TN3-c-R LR1108L-xx-AF5-R LR1108G-xx-AF5-R www.unisonic.com.tw Copyright © 2012 Unisonic Technologies Co., Ltd Package SOT-223 SOT-89 TO-252 SOT-25 I Pin Assignment c A: GOI C: GIO D: IGO G SD ERROR Packing Tape Reel O 1 of 6 QW-R102-031.I LR1108 CMOS IC MARKING INFORMATION PACKAGE VOLTAGE CODE MARKING SOT-223 4 5 15 :1.5V 18:1.8V 25:2.5V 2J:2.85V 33:3.3V 50: 5.0V SOT-25 SPXX 1 2 G: Halogen Free L : Lead Free 3 TO-252 SOT-89 PIN DESCRIPTION For SOT-223/SOT-89/TO-252 Package PIN CODE & NO PIN NAME A C D 2 3 3 VOUT 1 1 2 GND 3 2 1 VIN For SOT-25 Package PIN NO PIN NAME 1 VIN 2 GND I/O 3 SD I 4 ERROR O 5 VOUT O I/O O DESCRIPTION Output Voltage Ground Input Supply DESCRIPTION Input supply Ground Shutdown LR1108 enable; when the SD pin connects to GND will shutdown the LR1108; At normal operation, SD must be tied to VDD through a 10KΩ pull up resistor. Error flag, active low; when the output dropout of regulation due to low input voltage, the LR1108 produces a logic low signal at the ERROR pin. Output voltage UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 6 QW-R102-031.I LR1108 CMOS IC BLOCK DIAGRAM UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 6 QW-R102-031.I LR1108 CMOS IC ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL RATINGS UNIT 2.5~7.0 V Input Voltage (Operating) (Note 10) VIN Input Voltage (Survival) -0.3~+7.5 V Shutdown Input Voltage VIN(SHDN) -0.3~VIN+0.3 V Output Voltage (Survival), (Note 4, 5) VOUT -0.3~+7.5 V IOUT (Survival) Short Circuit Protected Maximum Voltage for ERROR Pin VIN+0.3 V Maximum Operating Current (DC) 1 A Power Dissipation (Note 2) PD Internally Limited Junction Temperature TJ +125 °C Operating Temperature TOPR -40~+125 °C Storage Temperature TSTG -65~+150 °C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. THERMAL DATA PARAMETER Junction to Ambient Junction to Case SYMBOL SOT-223 SOT-25 TO-252 SOT-89 SOT-223 SOT-25 TO-252 SOT-89 θJA θJC RATINGS 165 249 112 179 15 165 12 47 UNIT ℃/W ℃/W ELECTRICAL CHARACTERISTICS Limits in standard typeface are for TJ = 25°C, and limits in boldface type apply over the full operating temperature range. (TJ = 25°C, VIN = VO(NOM) + 1V, IL = 10mA, COUT = 2.2μF, VSD = VIN-0.3V, unless otherwise specified.) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT +1.5 0mA ≤ IL ≤ 1A -1.5 % 0 Output Voltage Tolerance (Note 6) VOUT +3 VOUT +1 ≤ VIN≤ 7.0V -3 Output Voltage Line Regulation (Note 6) △VOUT VOUT+1V<VIN<7.0V 0.05 % Output Voltage Load Regulation (Note 6) △VOUT/△IOUT 10mA < IL < 1A 0.04 % Dropout Voltage (Note 8) VD IL = 1A 300 500 mV 200 IL = 0mA Ground Pin Current In Normal Operation IGND uA Mode IL = 1A 300 Peak Output Current IO(PEAK) (Note 2) 1 A SHORT CIRCUIT PROTECTION Short Circuit Current ISC 2 A OVER TEMPERATURE PROTECTION Shutdown Threshold TSHDN(THR) 165 °C Thermal Shutdown Hysteresis TSHDN(HYS) 10 °C SHUTDOWN INPUT VIN Output = High VIN-0.3 V Shutdown Threshold VSHDN Output = Low 0 0.2 Turn-off Delay tD(OFF) IL = 1A 20 μs Turn-on Delay tD(ON) IL = 1A 25 μs SD Input Current ISD VSD = VIN 1 nA UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 4 of 6 QW-R102-031.I LR1108 CMOS IC ELECTRICAL CHARACTERISTICS(Cont.) PARAMETER ERROR FLAG COMPARATOR ERROR Flag Saturation ERROR Flag Pin Leakage Current Threshold Threshold Hysteresis Flag Reset Delay AC PARAMETERS SYMBOL VEF(SAT) II(LEAK) VT VTHR tD TEST CONDITIONS MIN ISINK = 100μA (Note 7) (Note 7) 5 2 TYP MAX UNIT 0.02 1 10 5 1 0.1 V nA % % μs 16 8 VIN = VOUT + 1.5V 60 COUT=100uF, VOUT = 3.3V dB Ripple Rejection PSRR VIN = VOUT + 0.3V 40 COUT=100uF, VOUT = 3.3V Output Noise Density ρN(L/F) f = 120Hz 0.8 μV BW = 10Hz ~ 100kHz 150 Output Noise Voltage eN μVRMS BW = 300Hz ~ 300kHz 100 Note 1. Conditions for which the device is intended to be functional is indicated by operating ratings, but specific performance limits isn’t be guaranteed. To make sure of specifications and test conditions, read Electrical Characteristics. Only for the test conditions listed the guaranteed specifications can be applied. When the device is not operated under the listed test conditions some performance characteristics may degrade. 2. Devices must be derated based on package thermal resistance at elevated temperatures. 3. The most likely parametric norm represents at 25°C. 4. The LR1108 output must be diode-clamped to ground. If used in a dual-supply system where the regulator load is returned to a negative supply. 5. Between the VIN and VOUT terminals the output PMOS structure contains a diode. This diode is reverse biased normally. If the voltage at the output terminal is forced to be higher than the voltage at the input terminal this diode will get forward biased. This diode can withstand 1Amp of peak current and 200mA of DC current typically. 6. Output voltage line regulation is the change in output voltage from the nominal value which is due to change in the input line voltage. Which is defined as the change in output voltage from the nominal value due to change in load current is output voltage load regulation. The load regulation and line regulation specification include the typical number only. But, the limits for load and line regulation are included in the output voltage tolerance specification. 7. Error Flag hysteresis and threshold are specified as regulated output voltage’s percentage. 8. At which the output drops 2% below the normal value dropout voltage is defined as the minimum input to output differential voltage. Only to output voltages of 2.5V and above dropout voltage specification applies. For output voltages below 2.5V, since the minimum input voltage is 2.5V, the drop-out voltage is nothing but the input to output differential. 9. Specification has been tested at -40°C ≤ TJ ≤ +85°Ccause under shutdown conditions the temperature rise of the device is negligible. 10. The minimum operating VIN value is equal to [VOUT(NOM) + VDROPOUT] or 2.5V, just the greater. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 6 QW-R102-031.I LR1108 CMOS IC TYPICAL APPLICATION CIRCUIT INPUT 3.3V±10% VIN VOUT 2.5V, 500mA VOUT UTC LR1108 CIN 1µF SD* SD ERROR ERROR (Note) COUT 4.7µF GND Note: SD and ERROR pins must be pulled high through a 10kΩ pull-up resistor. Connect the ERROR pin to ground if this function is not used. TYPICAL CHARACTERISTICS Dropout Voltage vs. Output Current Dropout Voltage, VD (mV) 350 300 250 200 150 100 50 0 0 250 500 750 1000 Output Current, IOUT (mA) UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 6 QW-R102-031.I