Intersil ISL83204A 60v/2.5a peak, high frequency full bridge fet driver Datasheet

ISL83204A
®
Data Sheet
March 20, 2007
60V/2.5A Peak, High Frequency Full Bridge
FET Driver
The ISL83204A is a high frequency, medium voltage Full
Bridge N-Channel FET driver IC, available in 20 lead plastic
SOIC and DIP packages. The ISL83204A includes an input
comparator used to facilitate the “hysteresis” and PWM
modes of operation. Its HEN (high enable) lead can force
current to freewheel in the bottom two external power
MOSFETs, maintaining the upper power MOSFETs off.
Since it can switch at frequencies up to 1MHz, the
ISL83204A is well suited for driving Voice Coil Motors,
switching power amplifiers and power supplies.
ISL83204A can also drive medium voltage brush motors,
and two ISL83204As can be used to drive high performance
stepper motors, since the short minimum “on-time” can
provide fine micro-stepping capability.
Short propagation delays of approximately 55ns maximize
control loop crossover frequencies and dead-times which
can be adjusted to near zero to minimize distortion, resulting
in precise control of the driven load.
FN6397.2
Features
• Drives N-Channel FET Full Bridge Including High Side
Chop Capability
• Bootstrap Supply Max Voltage to 75VDC
• Drives 1000pF Load at 1MHz in Free Air at +50°C with
Rise and Fall Times of Typically 10ns
• User-Programmable Dead Time
• Charge-Pump and Bootstrap Maintain Upper Bias
Supplies
• DIS (Disable) Pin Pulls Gates Low
• Input Logic Thresholds Compatible with 5V to 15V Logic
Levels
• Very Low Power Consumption
• Undervoltage Protection
• Pb-Free Plus Anneal Available (RoHS Compliant)
Applications
• Medium/Large Voice Coil Motors
Ordering Information
PART
NUMBER
ISL83204AIPZ
(Note)
• Full Bridge Power Supplies
TEMP
RANGE
(°C)
PART
MARKING
PKG.
PACKAGE DWG. #
ISL83204AIPZ -40 to +85 20 Ld PDIP
(Pb-Free)
E20.3
ISL83204AIBZ* ISL83204AIBZ -40 to +85 20 Ld SOIC
(Note)
(Pb-Free)
M20.3
• Uninterruptible Power Supplies
• High Performance Motor Controls
• Noise Cancellation Systems
• Battery Powered Vehicles
*Add “-T” suffix for tape and reel.
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100%
matte tin plate termination finish, which are RoHS compliant and
compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
1
• Switching Power Amplifiers
Pinout
ISL83204A
(20 LD PDIP, 20 LD SOIC)
TOP VIEW
BHB
1
HEN
2
19 BHS
DIS
3
18 BLO
VSS
4
17 BLS
OUT
5
16 VDD
IN+
6
15 VCC
IN-
7
14 ALS
HDEL
8
13 ALO
LDEL
9
12 AHS
AHB 10
11 AHO
20 BHO
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2007. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
ISL83204A
Application Block Diagram
60V
12V
BHO
BHS
HEN
LOAD
BLO
DIS
ISL83204A
IN+
ALO
AHS
IN-
AHO
GND
Functional Block Diagram
GND
(1/2 ISL83204A)
HIGH VOLTAGE BUS ≤ 60VDC
AHB
10
UNDERVOLTAGE
CHARGE
PUMP
LEVEL SHIFT
AND LATCH
DRIVER
CBS
AHS
VDD 16
HEN
AHO
11
12
2
TURN-ON
DELAY
DBS
DIS
3
OUT
5
IN+
6
IN_
7
HDEL
8
LDEL
9
VSS
4
TO VDD (PIN 16)
15 VCC
DRIVER
TURN-ON
DELAY
+
-
ALO
13
ALS
CBF
+12VDC
BIAS
SUPPLY
14
2
FN6397.2
March 20, 2007
ISL83204A
Typical Application (Hysteresis Mode Switching)
60V
1 BHB
BHO 20
2 HEN
BHS 19
DIS
3 DIS
BLO 18
4 VSS
BLS 17
5 OUT
6 IN+
6V
7 ININ
ISL83204A
12V
8 HDEL
LOAD
VDD 16
VCC 15
12V
ALS 14
ALO 13
9 LDEL
AHS 12
10 AHB
AHO 11
GND
+
6V
GND
3
FN6397.2
March 20, 2007
ISL83204A
Absolute Maximum Ratings
Thermal Information
Supply Voltage, VDD and VCC . . . . . . . . . . . . . . . . . . . . -0.3V to 16V
Logic I/O Voltages . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD +0.3V
Voltage on AHS, BHS . -6.0V (Transient) to 70V (+25°C to +125°C)
Voltage on AHS, BHS . . -6.0V (Transient) to 70V (-55°C to +125°C)
Voltage on ALS, BLS . . . . . . . -2.0V (Transient) to +2.0V (Transient)
Voltage on AHB, BHB . . . . . . VAHS, BHS -0.3V to VAHS, BHS +VDD
Voltage on ALO, BLO. . . . . . . . . . . . .VALS, BLS -0.3V to VCC +0.3V
Voltage on AHO, BHO . . . . . . VAHS, BHS -0.3V to VAHB, BHB +0.3V
Input Current, HDEL and LDEL . . . . . . . . . . . . . . . . . . -5mA to 0mA
Phase Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns
All Voltages relative to VSS, unless otherwise specified.
Thermal Resistance (Typical, Note 1)
θJA (°C/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
85
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
Maximum Power Dissipation at +85°C
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .470mW
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .530mW
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Operating Max. Junction Temperature. . . . . . . . . . . . . . . . . . +125°C
Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300°C
(For SOIC - Lead Tips Only)
Operating Conditions
Supply Voltage, VDD and VCC . . . . . . . . . . . . . . . . . . +9.5V to +15V
Voltage on ALS, BLS . . . . . . . . . . . . . . . . . . . . . . . . . -1.0V to +1.0V
Voltage on AHB, BHB . . . . . . . .VAHS, BHS +5V to VAHS, BHS +15V
Voltage on AHs, BHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60V
Input Current, HDEL and LDEL . . . . . . . . . . . . . . . .-500μA to -50μA
Operating Ambient Temperature Range . . . . . . . . . .-40°C to +85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications
VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL = 100k, and
TA = +25°C, Unless Otherwise Specified
TJ = +25°C
PARAMETERS
TJ = -40°C to +125°C
MIN
TYP
MAX
MIN
MAX
UNITS
IN- = 2.5V, Other Inputs = 0V
8
11
14
7
14
mA
Outputs switching f = 500kHz, No
Load
8
12
15
8
15
mA
IN- = 2.5V, Other Inputs = 0V,
IALO = IBLO = 0
-
25
80
-
100
μA
f = 500kHz, No Load
1
1.25
2.0
0.8
3
mA
IN- = 2.5V, Other Inputs = 0V,
IAHO = IBHO = 0,
VDD = VCC =VAHB = VBHB = 10V
-50
-25
-11
-60
-10
μA
SYMBOL
TEST CONDITIONS
SUPPLY CURRENTS AND CHARGE PUMPS
VDD Quiescent Current
IDD
VDD Operating Current
IDDO
VCC Quiescent Current
ICC
VCC Operating Current
ICCO
AHB, BHB Quiescent
Current -Qpump Output
Current
IAHB, IBHB
AHB, BHB Operating
Current
IAHBO,
IBHBO
f = 500kHz, No Load
0.62
1.2
1.5
0.5
1.9
mA
AHS, BHS, AHB, BHB
Leakage Current
IHLK
VBHS = VAHS = 60V,
VAHB = VBHB = 75V
-
0.02
1.0
-
10
μA
11.5
12.6
14.0
10.5
14.5
V
-10
0
+10
-15
+15
mV
IIB
0
0.5
2
0
4
μA
Input Offset Current
IOS
-1
0
+1
-2
+2
μA
Input Common Mode
Voltage Range
CMVR
1
-
VDD - 1.5
1
VDD - 1.5
V
AHB-AHS, BHB-BHS
Qpump Output Voltage
VAHB - VAHS IAHB = IAHB = 0, No Load
VBHB - VBHS
INPUT COMPARATOR PINS: IN+, IN-, OUT
Offset Voltage
VOS
Input Bias Current
4
Over Common Mode Voltage
Range
FN6397.2
March 20, 2007
ISL83204A
Electrical Specifications
VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL = 100k, and
TA = +25°C, Unless Otherwise Specified (Continued)
TJ = +25°C
PARAMETERS
SYMBOL
TEST CONDITIONS
TJ = -40°C to +125°C
MIN
TYP
MAX
MIN
MAX
UNITS
-
25
-
-
-
V/mV
Voltage Gain
AVOL
OUT High Level Output
Voltage
VOH
IN+ >IN-, IOH = -250μA
VDD - 0.4
-
-
VDD - 0.5
-
V
OUT Low Level Output
Voltage
VOL
IN+ <IN-, IOL = +250μA
-
-
0.4
-
0.5
V
Low Level Output Current
IOL
VOUT = 6V
6.5
14
19
6
20
mA
High Level Output Current
IOH
VOUT = 6V
-17
-10
-3
-20
-2.5
mA
Low Level Input Voltage
VIL
Full Operating Conditions
-
-
1.0
-
0.8
V
High Level Input Voltage
VIH
Full Operating Conditions
2.5
-
-
2.7
-
V
-
35
-
-
-
mV
INPUT PINS: DIS
Input Voltage Hysteresis
Low Level Input Current
IIL
VIN = 0V, Full Operating Conditions
-130
-100
-75
-135
-65
μA
High Level Input Current
IIH
VIN = 5V, Full Operating Conditions
-1
-
+1
-10
+10
μA
Low Level Input Voltage
VIL
Full Operating Conditions
-
-
1.0
-
0.8
V
High Level Input Voltage
VIH
Full Operating Conditions
2.5
-
-
2.7
-
V
-
35
-
-
-
mV
INPUT PINS: HEN
Input Voltage Hysteresis
Low Level Input Current
IIL
VIN = 0V, Full Operating Conditions
-260
-200
-150
-270
-130
μA
High Level Input Current
IIH
VIN = 5V, Full Operating Conditions
-1
-
+1
-10
+10
μA
IHDEL = ILDEL = -100μA
4.9
5.1
5.3
4.8
5.4
V
TURN-ON DELAY PINS: LDEL AND HDEL
LDEL, HDEL Voltage
VHDEL,V
GATE DRIVER OUTPUT PINS: ALO, BLO, AHO, AND BHO
Low Level Output Voltage
VOL
IOUT = 100mA
0.7
0.85
1.0
0.5
1.1
V
High Level Output Voltage
VCC - VOH
IOUT = -100mA
0.8
0.95
1.1
0.5
1.2
V
Peak Pullup Current
IO+
VOUT = 0V
1.7
2.6
3.8
1.4
4.1
A
Peak Pulldown Current
IO-
VOUT = 12V
1.7
2.4
3.3
1.3
3.6
A
Under Voltage, Rising
Threshold
UV+
8.1
8.8
9.4
8.0
9.5
V
Under Voltage, Falling
Threshold
UV-
7.6
8.3
8.9
7.5
9.0
V
Under Voltage, Hysteresis
HYS
0.25
0.4
0.65
0.2
0.7
V
5
FN6397.2
March 20, 2007
ISL83204A
Switching Specifications VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL = 10k,
CL = 1000pF, and TA = +25°C, Unless Otherwise Specified
TJ = +25°C
PARAMETERS
SYMBOL
TEST CONDITIONS
TJ = - 40°C to +125°C
MIN TYP MAX
MIN
MAX
UNITS
Lower Turn-off Propagation Delay (IN+/IN- to ALO/BLO)
tLPHL
-
40
70
-
90
ns
Upper Turn-off Propagation Delay (IN+/IN- to AHO/BHO)
tHPHL
-
50
80
-
110
ns
Lower Turn-on Propagation Delay (IN+/IN- to ALO/BLO)
tLPLH
-
40
70
-
90
ns
Upper Turn-on Propagation Delay (IN+/IN- to AHO/BHO)
tHPLH
-
70
110
-
140
ns
Rise Time
tR
-
10
25
-
35
ns
Fall Time
tF
-
10
25
-
35
ns
Turn-on Input Pulse Width
tPWIN-ON
50
-
-
50
-
ns
Turn-off Input Pulse Width
tPWIN-OFF
40
-
-
40
-
ns
Disable Turn-off Propagation Delay
(DIS - Lower Outputs)
tDISLOW
-
45
75
-
95
ns
Disable Turn-off Propagation Delay
(DIS - Upper Outputs)
tDISHIGH
-
55
85
-
105
ns
tDLPLH
-
45
70
-
90
ns
tREF-PW
240
380
500
200
600
ns
tUEN
-
480
630
-
750
ns
Disable to Lower Turn-on Propagation Delay
(DIS - ALO and BLO)
Refresh Pulse Width (ALO and BLO)
Disable to Upper Enable (DIS - AHO and BHO)
HEN-AHO, BHO Turn-off, Propagation Delay
tHEN-PHL
RHDEL = RLDEL = 10k
-
40
70
-
90
ns
HEN-AHO, BHO Turn-on, Propagation Delay
tHEN-PLH
RHDEL = RLDEL = 10k
-
60
90
-
110
ns
TRUTH TABLE
INPUT
OUTPUT
IN+ >IN-
HEN
U/V
DIS
ALO
AHO
BLO
BHO
X
X
X
1
0
0
0
0
0
0
0
0
1
0
0
0
1
1
0
0
0
1
1
0
0
1
0
0
1
0
0
1
1
0
0
0
0
0
1
0
X
X
1
X
0
0
0
0
6
FN6397.2
March 20, 2007
ISL83204A
Pin Descriptions
PIN
NUMBER
SYMBOL
1
BHB
B High-side Bootstrap supply. External bootstrap diode and capacitor are required. Connect cathode of bootstrap
diode and positive side of bootstrap capacitor to this pin. Internal charge pump supplies 30μA out of this pin to
maintain bootstrap supply. Internal circuitry clamps the bootstrap supply to approximately 12.8V.
2
HEN
High-side Enable input. Logic level input that when low overrides IN+/IN- (Pins 6 and 7) to put AHO and BHO drivers
(Pins 11 and 20) in low output state. When HEN is high AHO and BHO are controlled by IN+/IN- inputs. The pin can
be driven by signal levels of 0V to 15V (no greater than VDD).
3
DIS
DISable input. Logic level input that when taken high sets all four outputs low. DIS high overrides all other inputs.
When DIS is taken low the outputs are controlled by the other inputs. The pin can be driven by signal levels of 0V to
15V (no greater than VDD).
4
VSS
Chip negative supply, generally will be ground.
5
OUT
OUTput of the input control comparator. This output can be used for feedback and hysteresis.
6
IN+
Noninverting input of control comparator. If IN+ is greater than IN- (Pin 7) then ALO and BHO are low level outputs
and BLO and AHO are high level outputs. If IN+ is less than IN- then ALO and BHO are high level outputs and BLO
and AHO are low level outputs. DIS (Pin 3) high level will override IN+/IN- control for all outputs. HEN (Pin 2) low level
will override IN+/IN- control of AHO and BHO. When switching in four quadrant mode, dead time in a half bridge leg
is controlled by HDEL and LDEL (Pins 8 and 9).
7
IN-
Inverting input of control comparator. See IN+ (Pin 6) description.
8
HDEL
High-side turn-on DELay. Connect resistor from this pin to VSS to set timing current that defines the turn-on delay of
both high-side drivers. The low-side drivers turn-off with no adjustable delay, so the HDEL resistor guarantees no
shoot-through by delaying the turn-on of the high-side drivers. HDEL reference voltage is approximately 5.1V.
9
LDEL
Low-side turn-on DELay. Connect resistor from this pin to VSS to set timing current that defines the turn-on delay of
both low-side drivers. The high-side drivers turn-off with no adjustable delay, so the LDEL resistor guarantees no
shoot-through by delaying the turn-on of the low-side drivers. LDEL reference voltage is approximately 5.1V.
10
AHB
A High-side Bootstrap supply. External bootstrap diode and capacitor are required. Connect cathode of bootstrap
diode and positive side of bootstrap capacitor to this pin. Internal charge pump supplies 30μA out of this pin to
maintain bootstrap supply. Internal circuitry clamps the bootstrap supply to approximately 12.8V.
11
AHO
A High-side Output. Connect to gate of A High-side power MOSFET.
12
AHS
A High-side Source connection. Connect to source of A High-side power MOSFET. Connect negative side of
bootstrap capacitor to this pin.
13
ALO
A Low-side Output. Connect to gate of A Low-side power MOSFET.
14
ALS
A Low-side Source connection. Connect to source of A Low-side power MOSFET.
15
VCC
Positive supply to gate drivers. Must be same potential as VDD (Pin 16). Connect to anodes of two bootstrap diodes.
16
VDD
Positive supply to lower gate drivers. Must be same potential as VCC (Pin 15). De-couple this pin to VSS (Pin 4).
17
BLS
B Low-side Source connection. Connect to source of B Low-side power MOSFET.
18
BLO
B Low-side Output. Connect to gate of B Low-side power MOSFET.
19
BHS
B High-side Source connection. Connect to source of B High-side power MOSFET. Connect negative side of
bootstrap capacitor to this pin.
20
BHO
B High-side Output. Connect to gate of B High-side power MOSFET.
DESCRIPTION
7
FN6397.2
March 20, 2007
ISL83204A
Timing Diagrams
tHPHL
tDT
tLPLH
U/V = DIS 0
HEN 1
IN+ > INALO
AHO
BLO
BHO
tHPLH
tLPHL
tR
tF
(10% - 90%) (90% - 10%)
tDT
FIGURE 1. BI-STATE MODE
tHEN-PHL
tHEN-PLH
U/V = DIS 0
HEN
IN+ > INALO
AHO
BLO
BHO
FIGURE 2. HIGH SIDE CHOP MODE
tDLPLH
tDIS
tREF-PW
U/V or DIS
HEN
IN+ > INALO
AHO
BLO
BHO
tUEN
FIGURE 3. DISABLE FUNCTION
8
FN6397.2
March 20, 2007
ISL83204A
Typical Performance Curves
VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V,
RHDEL = RLDEL = 100k, and TA = +25°C, Unless Otherwise Specified.
13.0
14
IDD SUPPLY CURRENT (mA)
IDD SUPPLY CURRENT (mA)
12.5
12
10
8
6
4
12.0
11.5
11.0
10.5
2
8
10
12
10.0
14
200k
400k
600k
800k
SWITCHING FREQUENCY (Hz)
0
VDD SUPPLY VOLTAGE (V)
FIGURE 4. QUIESCENT IDD SUPPLY CURRENT vs VDD
SUPPLY VOLTAGE
1M
FIGURE 5. IDDO NO-LOAD IDD SUPPLY CURRENT vs
FREQUENCY (Hz)
+125°C
20
+75°C
ICC SUPPLY CURRENT (mA)
FLOATING SUPPLY BIAS CURRENT (mA)
5
15
10
5
0
4
+25°C
0°C
3
-40°C
2
1
0
0
100k 200k 300k 400k 500k 600k 700k 800k 900k 1M
0
100k 200k 300k 400k 500k 600k 700k 800k 900k 1M
SWITCHING FREQUENCY (Hz)
SWITCHING FREQUENCY (Hz)
FIGURE 7. ICCO, NO-LOAD ICC SUPPLY CURRENT vs
FREQUENCY (Hz) TEMPERATURE
2.5
COMPARATOR INPUT CURRENT (μA)
FLOATING SUPPLY BIAS CURRENT (mA)
FIGURE 6. SIDE A, B FLOATING SUPPLY BIAS CURRENT vs
FREQUENCY (LOAD = 1000pF)
2.0
1.5
1.0
0.5
1.0
0.5
0.0
0
400k
200k
600k
800k
SWITCHING FREQUENCY (Hz)
1M
FIGURE 8. IAHB, IBHB NO-LOAD FLOATING SUPPLY BIAS
CURRENT vs FREQUENCY
9
-40
-20
0
20
40
60
80
100
120
JUNCTION TEMPERATURE (°C)
FIGURE 9. COMPARATOR INPUT CURRENT IL vs
TEMPERATURE AT VCM = 5V
FN6397.2
March 20, 2007
ISL83204A
Typical Performance Curves
VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V,
RHDEL = RLDEL = 100k, and TA = +25°C, Unless Otherwise Specified. (Continued)
-180
LOW LEVEL INPUT CURRENT (μA)
LOW LEVEL INPUT CURRENT (μA)
-90
-100
-110
-120
-50
-25
0
25
50
75
100
-190
-200
-210
-220
-230
-40
125
-20
0
JUNCTION TEMPERATURE (°C)
PROPAGATION DELAY (ns)
NO-LOAD FLOATING CHARGE PUMP VOLTAGE (V)
80
100
120
80
14
13
12
11
70
60
50
40
30
-20
0
20
40
60
80
100
-40
120
-20
JUNCTION TEMPERATURE (°C)
0
20
40
60
80
100
120
JUNCTION TEMPERATURE (°C)
FIGURE 12. AHB - AHS, BHB - BHS NO-LOAD CHARGE PUMP
VOLTAGE vs TEMPERATURE
FIGURE 13. UPPER DISABLE TURN-OFF PROPAGATION
DELAY tDISHIGH vs TEMPERATURE
80
PROPAGATION DELAY (ns)
525
PROPAGATION DELAY (ns)
60
FIGURE 11. HEN LOW LEVEL INPUT CURRENT IIL vs
TEMPERATURE
15
500
475
450
425
-50
40
JUNCTION TEMPERATURE (°C)
FIGURE 10. DIS LOW LEVEL INPUT CURRENT IIL vs
TEMPERATURE
10
-40
20
70
60
50
40
30
-25
0
25
50
75
100
125 150
JUNCTION TEMPERATURE (°C)
FIGURE 14. DISABLE TO UPPER ENABLE tUEN
PROPAGATION DELAY vs TEMPERATURE
10
-40
-20
0
20
40
60
80
100
120
JUNCTION TEMPERATURE (°C)
FIGURE 15. LOWER DISABLE TURN-OFF PROPAGATION
DELAY tDISLOW vs TEMPERATURE
FN6397.2
March 20, 2007
ISL83204A
Typical Performance Curves
VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V,
RHDEL = RLDEL = 100k, and TA = +25°C, Unless Otherwise Specified. (Continued)
80
70
PROPAGATION DELAY (ns)
REFRESH PULSE WIDTH (ns)
450
425
400
375
60
50
40
30
350
-50
-25
0
25
50
75
100
20
-40
125 150
-20
JUNCTION TEMPERATURE (°C)
40
60
80
100
120
FIGURE 17. DISABLE TO LOWER ENABLE tDLPLH
PROPAGATION DELAY vs TEMPERATURE
90
PROPAGATION DELAY (ns)
90
PROPAGATION DELAY (ns)
20
JUNCTION TEMPERATURE (°C)
FIGURE 16. tTREF-PW REFRESH PULSE WIDTH vs
TEMPERATURE
80
70
60
50
80
70
60
50
40
40
-40
-20
0
20
40
60
80
100
JUNCTION TEMPERATURE (°C)
-40
120
-20
0
20
40
60
80
100
120
JUNCTION TEMPERATURE (°C)
FIGURE 18. UPPER TURN-OFF PROPAGATION DELAY tHPHL
vs TEMPERATURE
FIGURE 19. UPPER TURN-ON PROPAGATION DELAY tHPLH
vs TEMPERATURE
90
90
PROPAGATION DELAY (ns)
PROPAGATION DELAY (ns)
0
80
70
60
50
80
70
60
50
40
40
-40
-20
0
20
40
60
80
100
JUNCTION TEMPERATURE (°C)
120
FIGURE 20. LOWER TURN-OFF PROPAGATION DELAY tLPHL
vs TEMPERATURE
11
-40
-20
0
20
40
60
80
100
JUNCTION TEMPERATURE (°C)
120
FIGURE 21. LOWER TURN-ON PROPAGATION DELAY tLPLH
vs TEMPERATURE
FN6397.2
March 20, 2007
ISL83204A
Typical Performance Curves
VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL =
13.5
13.5
12.5
12.5
TURN-ON RISE TIME (ns)
GATE DRIVE FALL TIME (ns)
100K, and TA = +25°C, Unless Otherwise Specified.
11.5
10.5
9.5
11.5
10.5
9.5
8.5
-40
-20
0
20
40
60
80
100
8.5
-40
120
-20
0
JUNCTION TEMPERATURE (°C)
FIGURE 22. GATE DRIVE FALL TIME tF vs TEMPERATURE
60
80
100
120
1500
1250
5.5
VCC - VOH (mV)
HDEL, LDEL INPUT VOLTAGE (V)
40
FIGURE 23. GATE DRIVE RISE TIME tR vs TEMPERATURE
6.0
5.0
1000
750
-40°C
0°C
500
4.5
+25°C
250
+75°C
+125°C
0
4.0
-40
-20
0
20
40
60
80
100
10
120
12
14
BIAS SUPPLY VOLTAGE (V)
JUNCTION TEMPERATURE (°C)
FIGURE 24. VLDEL, VHDEL VOLTAGE vs TEMPERATURE
FIGURE 25. HIGH LEVEL OUTPUT VOLTAGE, VCC - VOH vs
BIAS SUPPLY AND TEMPERATURE AT 100μA
3.5
GATE DRIVE SINK CURRENT (A)
1500
1250
1000
VOL (mV)
20
JUNCTION TEMPERATURE (°C)
750
-40°C
500
0°C
+25°C
250
+75°C
+125°C
0
10
3.0
2.5
2.0
1.5
1.0
0.5
0.0
12
BIAS SUPPLY VOLTAGE (V)
14
FIGURE 26. LOW LEVEL OUTPUT VOLTAGE VOL vs BIAS
SUPPLY AND TEMPERATURE AT 100μA
12
6
7
8
9
10
11
12
13
14
15
16
VCC, VDD, VAHG, VBHB (V)
FIGURE 27. PEAK PULLDOWN CURRENT IO- BIAS SUPPLY
VOLTAGE
FN6397.2
March 20, 2007
ISL83204A
Typical Performance Curves
VDD = VCC = VAHB = VBHB = 12V, VSS = VALS = VBLS = VAHS = VBHS = 0V, RHDEL = RLDEL =
100K, and TA = +25°C, Unless Otherwise Specified. (Continued)
500
LOW VOLTAGE BIAS CURRENT (mA)
GATE DRIVE SINK CURRENT (A)
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
6
7
8
9
10
11
12
13
14
15
200
100
10,000
50
3,000
20
1,000
10
100
5
2
1
0.5
0.2
0.1
16
1k
2k
VCC, VDD, VABH, VBHB (V)
10k
20k
50k 100k 200k
500k 1M
SWITCHING FREQUENCY (Hz)
FIGURE 28. PEAK PULLUP CURRENT IO+ vs SUPPLY
VOLTAGE
FIGURE 29. LOW VOLTAGE BIAS CURRENT IDD AND ICC
(LESS QUIESCENT COMPONENT) vs
FREQUENCY AND GATE LOAD CAPACITANCE
9.0
BIAS SUPPLY VOLTAGE, VDD (V)
1000
500
LEVEL-SHIFT CURRENT (μA)
5k
200
100
50
20
UV+
8.8
8.6
UV8.4
8.2
10
10k
20k
50k
100k
200k
500k
1M
50
25
0
25
SWITCHING FREQUENCY (Hz)
50
75
100
125
150
TEMPERATURE (°C)
FIGURE 30. HIGH VOLTAGE LEVEL-SHIFT CURRENT vs
FREQUENCY AND BUS VOLTAGE
FIGURE 31. UNDERVOLTAGE LOCKOUT vs TEMPERATURE
150
DEAD-TIME (ns)
120
90
60
30
0
10
50
100
150
200
HDEL/LDEL RESISTANCE (kΩ)
250
FIGURE 32. MINIMUM DEAD-TIME vs DEL RESISTANCE
13
FN6397.2
March 20, 2007
ISL83204A
Dual-In-Line Plastic Packages (PDIP)
N
E20.3 (JEDEC MS-001-AD ISSUE D)
E1
INDEX
AREA
1 2 3
20 LEAD DUAL-IN-LINE PLASTIC PACKAGE
N/2
INCHES
-B-
SYMBOL
-AD
E
BASE
PLANE
-C-
SEATING
PLANE
A2
A
L
D1
e
B1
D1
eA
A1
eC
B
0.010 (0.25) M
C
L
C A B S
C
eB
NOTES:
1. Controlling Dimensions: INCH. In case of conflict between English
and Metric dimensions, the inch dimensions control.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Symbols are defined in the “MO Series Symbol List” in Section 2.2
of Publication No. 95.
4. Dimensions A, A1 and L are measured with the package seated in
JEDEC seating plane gauge GS-3.
5. D, D1, and E1 dimensions do not include mold flash or protrusions.
Mold flash or protrusions shall not exceed 0.010 inch (0.25mm).
6. E and eA are measured with the leads constrained to be perpendicular to datum -C- .
MILLIMETERS
MIN
MAX
MIN
MAX
NOTES
A
-
0.210
-
5.33
4
A1
0.015
-
0.39
-
4
A2
0.115
0.195
2.93
4.95
-
B
0.014
0.022
0.356
0.558
-
B1
0.045
0.070
1.55
1.77
8
C
0.008
0.014
0.204
0.355
-
D
0.980
1.060
24.89
26.9
5
D1
0.005
-
0.13
-
5
E
0.300
0.325
7.62
8.25
6
E1
0.240
0.280
6.10
7.11
5
e
0.100 BSC
2.54 BSC
-
eA
0.300 BSC
7.62 BSC
6
eB
-
0.430
-
10.92
7
L
0.115
0.150
2.93
3.81
4
N
20
20
9
Rev. 0 12/93
7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater.
8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm).
9. N is the maximum number of terminal positions.
10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3,
E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm).
14
FN6397.2
March 20, 2007
ISL83204A
Small Outline Plastic Packages (SOIC)
M20.3 (JEDEC MS-013-AC ISSUE C)
20 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE
N
INDEX
AREA
H
0.25(0.010) M
B M
INCHES
E
MILLIMETERS
SYMBOL
MIN
MAX
MIN
MAX
NOTES
A
0.0926
0.1043
2.35
2.65
-
A1
0.0040
0.0118
0.10
0.30
-
B
0.014
0.019
0.35
0.49
9
C
0.0091
0.0125
0.23
0.32
-
D
0.4961
0.5118
12.60
13.00
3
E
0.2914
0.2992
7.40
7.60
4
-B1
2
3
L
SEATING PLANE
-A-
A
D
h x 45°
-C-
e
α
e
A1
B
C
0.10(0.004)
0.25(0.010) M
C A M
B S
0.050 BSC
1.27 BSC
-
H
0.394
0.419
10.00
10.65
-
h
0.010
0.029
0.25
0.75
5
L
0.016
0.050
0.40
1.27
6
N
α
20
0°
20
8°
0°
7
8°
NOTES:
Rev. 2 6/05
1. Symbols are defined in the “MO Series Symbol List” in Section
2.2 of Publication Number 95.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate
burrs. Mold flash, protrusion and gate burrs shall not exceed
0.15mm (0.006 inch) per side.
4. Dimension “E” does not include interlead flash or protrusions.
Interlead flash and protrusions shall not exceed 0.25mm (0.010
inch) per side.
5. The chamfer on the body is optional. If it is not present, a visual
index feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater
above the seating plane, shall not exceed a maximum value of
0.61mm (0.024 inch)
10. Controlling dimension: MILLIMETER. Converted inch
dimensions are not necessarily exact.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
15
FN6397.2
March 20, 2007
Similar pages