TI1 LMC6041AIMX Lmc6041 cmos single micropower operational amplifier Datasheet

LMC6041
www.ti.com
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
LMC6041 CMOS Single Micropower Operational Amplifier
Check for Samples: LMC6041
FEATURES
DESCRIPTION
1
•
•
•
•
•
2
Low Supply Current: 14 μA (Typ)
Operates from 4.5V to 15.5V Single Supply
Ultra Low Input Current: 2 fA (Typ)
Rail-to-Rail Output Swing
Input Common-Mode Range Includes Ground
APPLICATIONS
•
•
•
•
•
•
•
Battery Monitoring and Power Conditioning
Photodiode and Infrared Detector Preamplifier
Silicon Based Transducer Systems
Hand-Held Analytic Instruments
pH Probe Buffer Amplifier
Fire and Smoke Detection Systems
Charge Amplifier for Piezoelectric Transducers
Ultra-low power consumption and low input-leakage
current are the hallmarks of the LMC6041. Providing
input currents of only 2 fA typical, the LMC6041 can
operate from a single supply, has output swing
extending to each supply rail, and an input voltage
range that includes ground.
The LMC6041 is ideal for use in systems requiring
ultra-low power consumption. In addition, the
insensitivity to latch-up, high output drive, and output
swing to ground without requiring external pull-down
resistors make it ideal for single-supply batterypowered systems.
Other applications for the LMC6041 include bar code
reader amplifiers, magnetic and electric field
detectors, and hand-held electrometers.
This device is built with TI's advanced Double-Poly
Silicon-Gate CMOS process.
See the LMC6042 for a dual, and the LMC6044 for a
quad amplifier with these features.
Connection Diagrams
Top View
Figure 1. 8-Pin SOIC or PDIP Package
See Package Number D0008A or P0008E
Figure 2. Low-Leakage Sample and Hold
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1994–2013, Texas Instruments Incorporated
LMC6041
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1) (2)
Differential Input Voltage
±Supply Voltage
Supply Voltage (V+ − V−)
16V
Output Short Circuit to V−
See (3)
Output Short Circuit to V+
See (4)
Lead Temperature (Soldering, 10 sec.)
260°C
−65°C to +150°C
Storage Temperature Range
Junction Temperature
110°C
ESD Tolerance (5)
500V
Current at Input Pin
±5 mA
Current at Output Pin
±18 mA
Current at Power Supply Pin
35 mA
(V+) + 0.3V, (V−) − 0.3V
Voltage at Input/Output Pin
See (6)
Power Dissipation
(1)
(2)
(3)
(4)
(5)
(6)
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating conditions indicate conditions for
which the device is intended to be functional, but do not ensure specific performance limits. For ensured specifications and test
conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed.
If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications.
Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature of 110°C. Output currents in excess of ±30 mA over long term may adversely
affect reliability.
Do not connect output to V+ when V+ is greater than 13V or reliability may be adversely affected.
Human body model, 1.5 kΩ in series with 100 pF.
The maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(max) − TA)/θJA.
Operating Ratings
Temperature Range
LMC6041AI, LMC6041I
−40°C ≤ TJ ≤ +85°C
4.5V ≤ V+ ≤ 15.5V
Supply Voltage
See (1)
Power Dissipation
Thermal Resistance (θJA)
(1)
(2)
2
(2)
8-Pin PDIP package
101°C/W
8-Pin SOIC package
165°C/W
For operating at elevated temperatures the device must be derated based on the thermal resistance θJA with PD = (TJ − TA)/θJA.
All numbers apply for packages soldered directly into a PC board.
Submit Documentation Feedback
Copyright © 1994–2013, Texas Instruments Incorporated
Product Folder Links: LMC6041
LMC6041
www.ti.com
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
Electrical Characteristics
Unless otherwise specified, all limits ensured for TA = TJ = 25°C. Boldface limits apply at the temperature extremes. V+ = 5V,
V− = 0V, VCM = 1.5V, VO = V+/2, and RL > 1M unless otherwise specified.
Parameter
VOS
Test Conditions
Typical (1)
Input Offset Voltage
1
TCVOS
Input Offset Voltage
Average Drift
IB
Input Bias Current
0.002
IOS
Input Offset Current
0.001
RIN
Input Resistance
CMRR
Common Mode Rejection
Ratio
0V ≤ VCM ≤ 12.0V
V+ = 15V
75
Positive Power Supply
Rejection Ratio
5V ≤ V+ ≤ 15V
VO = 2.5V
75
−PSRR
Negative Power Supply
Rejection Ratio
0V ≤ V− ≤ −10V
VO = 2.5V
CMR
Input Common-Mode
Voltage Range
V+ = 5V and 15V
for CMRR ≥ 50 dB
+PSRR
LMC6041AI
Limit (2)
3
6
mV
6.3
max
μV/°C
4
4
pA
max
2
2
pA
max
68
62
dB
66
60
min
68
62
dB
66
60
min
94
84
74
dB
83
73
min
−0.4
−0.1
−0.1
V
0
0
max
V+ − 2.3V
V+ − 2.3V
V
>10
TeraΩ
+
Large Signal Voltage Gain
RL = 100 kΩ (3)
Sourcing
Sinking
RL = 25 kΩ (3)
VO
Output Swing
1000
500
+
V − 2.5V
V − 2.4V
min
400
300
V/mV
300
200
min
180
90
V/mV
120
70
min
200
100
V/mV
Sourcing
1000
160
80
min
Sinking
250
100
50
V/mV
60
40
min
4.987
4.970
4.940
V
4.950
4.910
min
0.030
0.060
V
0.050
0.090
max
4.920
4.870
V
4.870
4.820
min
0.010
0.080
0.130
V
0.130
0.180
max
14.970
14.920
14.880
V
14.880
14.820
min
0.007
0.030
0.060
V
0.050
0.090
max
14.950
14.900
14.850
V
14.850
14.800
min
0.100
0.150
V
0.150
0.200
max
V+ = 5V
RL = 100 kΩ to V+/2
0.004
V+ = 5V
RL = 25 kΩ to V+/2
V+ = 15V
RL = 100 kΩ to V+/2
V+ = 15V
RL = 25 kΩ to V+/2
4.980
0.022
(1)
(2)
(3)
Units
(Limit)
3.3
1.3
V+ − 1.9V
AV
LMC6041I
Limit (2)
Typical Values represent the most likely parametric norm.
All limits are ensured at room temperature (standard type face) or at operating temperature extremes (bold face type).
V+ = 15V, VCM = 7.5V and RL connected to 7.5V. For Sourcing tests, 7.5V ≤ VO ≤ 11.5V. For Sinking tests, 2.5V ≤ VO ≤ 7.5V.
Submit Documentation Feedback
Copyright © 1994–2013, Texas Instruments Incorporated
Product Folder Links: LMC6041
3
LMC6041
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
www.ti.com
Electrical Characteristics (continued)
Unless otherwise specified, all limits ensured for TA = TJ = 25°C. Boldface limits apply at the temperature extremes. V+ = 5V,
V− = 0V, VCM = 1.5V, VO = V+/2, and RL > 1M unless otherwise specified.
Parameter
ISC
Output Current
V+ = 5V
Test Conditions
Typical (1)
LMC6041AI
Limit (2)
LMC6041I
Limit (2)
22
16
13
mA
10
8
min
16
13
mA
8
8
min
15
15
mA
10
10
min
21
mA
min
Sourcing, VO = 0V
Sinking, VO = 5V
ISC
Output Current
V+ = 15V
IS
Supply Current
21
Sourcing, VO = 0V
40
Sinking, VO = 13V (4)
39
24
8
8
VO = 1.5V
14
20
26
μA
24
30
max
26
34
μA
31
39
max
V+ = 15V
(4)
Units
(Limit)
18
Do not connect output to V+ when V+ is greater than 13V or reliability may be adversely affected.
AC Electrical Characteristics
Unless otherwise specified, all limits ensured for TA = TJ = 25°C. Boldface limits apply at the temperature extremes. V+ = 5V,
V− = 0V, VCM = 1.5V, VO = V+/2, and RL > 1M unless otherwise specified.
Parameter
SR
Slew Rate
Test Conditions
See (3)
Typ (1)
0.02
LMC6041AI
LMC6041I
Limit (2)
Units
(Limit)
0.015
0.010
V/μs
0.010
0.007
min
Limit
(2)
GBW
Gain-Bandwidth Product
75
kHz
φm
Phase Margin
60
Deg
en
Input-Referred Voltage Noise
F = 1 kHz
83
nV/√Hz
in
Input-Referred Current Noise
F = 1 kHz
0.0002
pA/√Hz
THD
Total Harmonic Distortion
F = 1 kHz, AV = −5
RL = 100 kΩ, VO = 2 Vpp
±5V Supply
0.01
%
(1)
(2)
(3)
4
Typical Values represent the most likely parametric norm.
All limits are ensured at room temperature (standard type face) or at operating temperature extremes (bold face type).
V+ = 15V. Connected as Voltage Follower with 10V step input. Number specified in the slower of the positive and negative slew rates.
Submit Documentation Feedback
Copyright © 1994–2013, Texas Instruments Incorporated
Product Folder Links: LMC6041
LMC6041
www.ti.com
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
Typical Performance Characteristics
VS = ± 7.5V, TA = 25°C unless otherwise specified
Supply Current
vs
Supply Voltage
Offset Voltage
vs
Temperature of Five Representative Units
Figure 3.
Figure 4.
Input Bias Current
vs
Temperature
Input Bias Current
vs
Input Common-Mode Voltage
Figure 5.
Figure 6.
Input Common-Mode Voltage Range
vs
Temperature
Output Characteristics
Current Sinking
Figure 7.
Figure 8.
Submit Documentation Feedback
Copyright © 1994–2013, Texas Instruments Incorporated
Product Folder Links: LMC6041
5
LMC6041
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
VS = ± 7.5V, TA = 25°C unless otherwise specified
6
Output Characteristics
Current Sourcing
Input Voltage Noise
vs
Frequency
Figure 9.
Figure 10.
Power Supply Rejection Ratio
vs
Frequency
CMRR
vs
Frequency
Figure 11.
Figure 12.
CMRR
vs
Temperature
Open-Loop Voltage Gain
vs
Temperature
Figure 13.
Figure 14.
Submit Documentation Feedback
Copyright © 1994–2013, Texas Instruments Incorporated
Product Folder Links: LMC6041
LMC6041
www.ti.com
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
VS = ± 7.5V, TA = 25°C unless otherwise specified
Open-Loop
Frequency Response
Gain and Phase Responses
vs
Load Capacitance
Figure 15.
Figure 16.
Gain and Phase Responses
vs
Temperature
Gain Error (VOS
vs
VOUT)
Figure 17.
Figure 18.
Common-Mode Error
vs
Common-Mode Voltage of Three Representative Units
Non-Inverting Slew Rate
vs
Temperature
Figure 19.
Figure 20.
Submit Documentation Feedback
Copyright © 1994–2013, Texas Instruments Incorporated
Product Folder Links: LMC6041
7
LMC6041
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
VS = ± 7.5V, TA = 25°C unless otherwise specified
8
Inverting Slew Rate
vs
Temperature
Non-Inverting Large
Signal Pulse Response
(AV = +1)
Figure 21.
Figure 22.
Non-Inverting Small
Signal Pulse Response
Inverting Large-Signal
Pulse Response
Figure 23.
Figure 24.
Inverting Small Signal
Pulse Response
Stability
vs
Capacitive Load (AV = +1)
Figure 25.
Figure 26.
Submit Documentation Feedback
Copyright © 1994–2013, Texas Instruments Incorporated
Product Folder Links: LMC6041
LMC6041
www.ti.com
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
Typical Performance Characteristics (continued)
VS = ± 7.5V, TA = 25°C unless otherwise specified
Stability
vs
Capacitive Load (AV = ±10)
Figure 27.
Submit Documentation Feedback
Copyright © 1994–2013, Texas Instruments Incorporated
Product Folder Links: LMC6041
9
LMC6041
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
www.ti.com
APPLICATIONS HINTS
AMPLIFIER TOPOLOGY
The LMC6041 incorporates a novel op-amp design topology that enables it to maintain rail-to-rail output swing
even when driving a large load. Instead of relying on a push-pull unity gain output buffer stage, the output stage
is taken directly from the internal integrator, which provides both low output impedance and large gain. Special
feed-forward compensation design techniques are incorporated to maintain stability over a wider range of
operating conditions than traditional micropower op-amps. These features make the LMC6041 both easier to
design with, and provide higher speed than products typically found in this ultra-low power class.
COMPENSATING FOR INPUT CAPACITANCE
It is quite common to use large values of feedback resistance with amplifiers with ultra-low input current, like the
LMC6041.
Although the LMC6041 is highly stable over a wide range of operating conditions, certain precautions must be
met to achieve the desired pulse response when a large feedback resistor is used. Large feedback resistors and
even small values of input capacitance, due to transducers, photodiodes, and circuits board parasitics, reduce
phase margins.
When high input impedance are demanded, guarding of the LMC6041 is suggested. Guarding input lines will not
only reduce leakage, but lowers stray input capacitance as well. (See Printed-Circuit-Board Layout for High
Impedance Work.)
Figure 28. Cancelling the Effect of Input Capacitance
The effect of input capacitance can be compensated for by adding a capacitor. Adding a capacitor, Cf, around
the feedback resistor (as in Figure 28 ) such that:
(1)
or
R1 CIN ≤ R2 Cf
(2)
Since it is often difficult to know the exact value of CIN, Cf can be experimentally adjusted so that the desired
pulse response is achieved. Refer to the LMC660 and the LMC662 for a more detailed discussion on
compensating for input capacitance.
CAPACITIVE LOAD TOLERANCE
Direct capacitive loading will reduce the phase margin of many op-amps. A pole in the feedback loop is created
by the combination of the op-amp's output impedance and the capacitive load. This pole induces phase lag at the
unity-gain crossover frequency of the amplifier resulting in either an oscillatory or underdamped pulse response.
With a few external components, op amps can easily indirectly drive capacitive loads, as shown in Figure 29.
10
Submit Documentation Feedback
Copyright © 1994–2013, Texas Instruments Incorporated
Product Folder Links: LMC6041
LMC6041
www.ti.com
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
Figure 29. LMC6041 Noninverting Gain of 10 Amplifier, Compensated to Handle Capacitive Loads
In the circuit of Figure 29, R1 and C1 serve to counteract the loss of phase margin by feeding the high frequency
component of the output signal back to the amplifier's inverting input, thereby preserving phase margin in the
overall feedback loop.
Capacitive load driving capability is enhanced by using a pull up resistor to V+ (Figure 30 ). Typically a pull up
resistor conducting 10 μA or more will significantly improve capacitive load responses. The value of the pull up
resistor must be determined based on the current sinking capability of the amplifier with respect to the desired
output swing. Open loop gain of the amplifier can also be affected by the pull up resistor (see Electrical
Characteristics).
Figure 30. Compensating for Large
Capacitive Loads with a Pull Up Resistor
PRINTED-CIRCUIT-BOARD LAYOUT
FOR HIGH-IMPEDANCE WORK
It is generally recognized that any circuit which must operate with less than 1000 pA of leakage current requires
special layout of the PC board. When one wishes to take advantage of the ultra-low bias current of the
LMC6041, typically less than 2fA, it is essential to have an excellent layout. Fortunately, the techniques of
obtaining low leakages are quite simple. First, the user must not ignore the surface leakage of the PC board,
even though it may sometimes appear acceptably low, because under conditions of high humidity or dust or
contamination, the surface leakage will be appreciable.
To minimize the effect of any surface leakage, lay out a ring of foil completely surrounding the LMC6041's inputs
and the terminals of capacitors, diodes, conductors, resistors, relay terminals, etc. connected to the op-amp's
inputs, as in Figure 31. To have a significant effect, guard rings should be placed on both the top and bottom of
the PC board. This PC foil must then be connected to a voltage which is at the same voltage as the amplifer
inputs, since no leakage current can flow between two points at the same potential. For example, a PC board
trace-to-pad resistance of 1012Ω, which is normally considered a very large resistance, could leak 5 pA if the
trace were a 5V bus adjacent to the pad of the input. This would cause a 100 times degradation from the
LMC6041's actual performance. However, if a guard ring is held within 5 mV of the inputs, then even a
resistance of 1011Ω would cause only 0.05 pA of leakage current. See Figure 34 for typical connections of guard
rings for standard op-amp configurations.
Submit Documentation Feedback
Copyright © 1994–2013, Texas Instruments Incorporated
Product Folder Links: LMC6041
11
LMC6041
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
www.ti.com
Figure 31. Example of Guard Ring
in P.C. Board Layout
Figure 32. Inverting Amplifier
Figure 33. Follower
Non-Inverting Amplifier
Figure 34. Typical Connections of Guard Rings
The designer should be aware that when it is inappropriate to lay out a PC board for the sake of just a few
circuits, there is another technique which is even better than a guard ring on a PC board: Don't insert the
amplifier's input pin into the board at all, but bend it up in the air and use only air as an insulator. Air is an
excellent insulator. In this case you may have to forego some of the advantages of PC board construction, but
the advantages are sometimes well worth the effort of using point-to-point up-in-the-air wiring. See Figure 35.
12
Submit Documentation Feedback
Copyright © 1994–2013, Texas Instruments Incorporated
Product Folder Links: LMC6041
LMC6041
www.ti.com
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
(Input pins are lifted out of PC board and soldered directly to components. All other pins connected to PC board.)
Figure 35. Air Wiring
Typical Single-Supply Applications
(V+ = 5.0 VDC)
The extremely high input impedance, and low power consumption, of the LMC6041 make it ideal for applications
that require battery-powered instrumentation amplifiers. Examples of these type of applications are hand-held pH
probes, analytic medical instruments, magnetic field detectors, gas detectors, and silicon based pressure
transducers.
Figure 36. Two Op-Amp Instrumentation Amplifier
The circuit in Figure 36 is recommended for applications where the common-mode input range is relatively low
and the differential gain will be in the range of 10 to 1000. This two op-amp instrumentation amplifier features an
independent adjustment of the gain and common-mode rejection trim, and a total quiescent supply current of less
than 28 μA. To maintain ultra-high input impedance, it is advisable to use ground rings and consider PC board
layout an important part of the overall system design (see Printed-Circuit-Board Layout for High Impedance
Work). Referring to Figure 36, the input voltages are represented as a common-mode input VCM plus a
differential input VD.
Rejection of the common-mode component of the input is accomplished by making the ratio of R1/R2 equal to
R3/R4. So that where,
(3)
A suggested design guideline is to minimize the difference of value between R1 through R4. This will often result
in improved resistor tempco, amplifier gain, and CMRR over temperature. If RN = R1 = R2 = R3 = R4 then the
gain equation can be simplified:
(4)
Due to the “zero-in, zero-out” performance of the LMC6041, and output swing rail-rail, the dynamic range is only
limited to the input common-mode range of 0V to VS–2.3V, worst case at room temperature. This feature of the
LMC6041 makes it an ideal choice for low-power instrumentation systems.
Submit Documentation Feedback
Copyright © 1994–2013, Texas Instruments Incorporated
Product Folder Links: LMC6041
13
LMC6041
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
www.ti.com
A complete instrumentation amplifier designed for a gain of 100 is shown in Figure 37. Provisions have been
made for low sensitivity trimming of CMRR and gain.
Figure 37. Low-Power Two-Op-Amp Instrumentation Amplifier
Figure 38. Low-Leakage Sample and Hold
Figure 39. Instrumentation Amplifier
Figure 40. 1 Hz Square-Wave Oscillator
14
Submit Documentation Feedback
Copyright © 1994–2013, Texas Instruments Incorporated
Product Folder Links: LMC6041
LMC6041
www.ti.com
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
Figure 41. AC Coupled Power Amplifier
Submit Documentation Feedback
Copyright © 1994–2013, Texas Instruments Incorporated
Product Folder Links: LMC6041
15
LMC6041
SNOS610E – DECEMBER 1994 – REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision D (March 2013) to Revision E
•
16
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 15
Submit Documentation Feedback
Copyright © 1994–2013, Texas Instruments Incorporated
Product Folder Links: LMC6041
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LMC6041AIM
NRND
SOIC
D
8
95
TBD
Call TI
Call TI
-40 to 85
LMC60
41AIM
LMC6041AIM/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
LMC60
41AIM
LMC6041AIMX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
LMC60
41AIM
LMC6041IM
NRND
SOIC
D
8
95
TBD
Call TI
Call TI
-40 to 85
LMC60
41IM
LMC6041IM/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
LMC60
41IM
LMC6041IMX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
SN | CU SN
Level-1-260C-UNLIM
-40 to 85
LMC60
41IM
LMC6041IN/NOPB
ACTIVE
PDIP
P
8
40
Green (RoHS
& no Sb/Br)
SN | CU SN
Level-1-NA-UNLIM
-40 to 85
LMC60
41IN
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
1-Nov-2013
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LMC6041AIMX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LMC6041IMX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Sep-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LMC6041AIMX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
LMC6041IMX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated