MD-010 M D -0 10 GPS Disciplined Oscillator Module Former Model C6300 MD-010 The MD010 is a Vectron standard platform module that provides 1 pps TTL,10 MHz sine wave and 10 MHz square wave outputs that are disciplined to an external 1pps reference. Internal to the module is a Vectron oscillator, ranging from a TCXO to a double oven OCXO, dependent upon performance requirements. Internal oscillators are capable of achieving an aging rate less as high as than 0.1ppb/day and stability over the operating temperature range of less than 0.2ppb. In addition to the 7 standard models included in this data sheet, due to Vectron’s extensive portfolio of oscillators and a firmware driven architecture, Vectron can customize a solution for your specific application. Features • • • • • • Applications Embedded GPS Receiver 1pps TTL output signals standard 10MHz sinewave and square wave outputs standard Other output frequencies available Embedded oscillator dependent upon holdover requirements Serial communications interface standard • • • • • • • 3G Basestations (WCDMA, CDMA2000) LTE WiMAX Basestations Digital Video Broadcast E911 Location Systems General Timing and Synchronization Military Radio Block Diagram Manual Holdover Serial Communications Interface Output Locked Module OK Hardware Reset Processor/ Controller Output Frequency Generation 1PPS Input (Optional - other input options available) Quartz Oscillator (OCXO or TCXO) Figure 1. Functional Block Diagram Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com 1PPS Output RF Output (10 MHz standard - other frequencies available) Summary Specifications Comparitive Performance of Standard Modules Model Embedded Oscillator Typical Uses MD-0100-DXJ-TCXO-10M0000000 TCXO MD-0102-DXJ-HPTC-10M0000000 High Precision TCXO Applications requiring 1 hour hold over on the order of 10 us MD-0101-DXJ-EMXO-10M0000000 EMXO Applications requiring 8 hour hold over on the order of 100 us MD-0101-DXJ-DAEM-10M0000000 Digitally Assisted EMXO Applications requiring a GPS disciplined clock with little or no hold over Application requiring 8 hour hold over of 100us over extended temperature ranges OCXO MD-0103-BXJ-OCXO-10M0000000 Applications requiring 8 hour hold over of 50 us over extended temperature ranges MD-0103-BXJ-DAOC-10M0000000 Digitally Assisted OCXO MD-0104-BXJ-DOCX-10M0000000 Double Oven OCXO Applications requiring 24 hour hold over on the order of 20 us Applications with stringent hold over requirements, 8.6 us over 24 hour Hold Over Performance (detailed performance on page 5) 1 Hold Over Time 10 min 1 hr 1 hr 8 hr Hold Over DT= Temperature Change 2 oC DT= DT= 2 oC 10 oC Model 8 hr 24hr 24 hr DT= DT= DT= DT= 2 oC 10 oC 2 oC 10 oC Maximum Accumulated Hold Over in us MD-0100-DXJ-TCXO-10M0000000 4.9 32 120 500 1200 2400 4700 MD-0102-DXJ-HPTC-10M0000000 1.5 12 27 270 380 2000 2400 MD-0101-DXJ-EMXO-10M0000000 2.5 12.5 60 105 490 340 1500 MD-0101-DXJ-DAEM-10M0000000 0.4 2 8.7 20 75 90 250 MD-0103-BXJ-OCXO-10M0000000 0.14 0.9 4 9 30 35 100 MD-0103-BXJ-DAOC-10M0000000 0.05 0.24 0.4 4.5 3.7 18 21 MD-0104-BXJ-DOCX-10M0000000 0.05 0.09 .21 1 2.5 5.9 10 Summary Performance Characteristics Model Warm Up Time (minutes) Aging / day (ppb)1 Temperature Stability (ppb)2 Module Height (mm) MD-0110-DXJ-TCXO-10M0000000 5 40 280 11 100 ns 5E-12 0.3 0.3 5 Accuracy to UTC (+/-1sigma) Accuracy (+/-) 3 Warm Steady up State Power @ Power @ 25 oC 25 oC (W) (W) Voltage (V) MD-0112-DXJ-HPTC-10M0000000 5 40 50 12.6 100 ns 5E-12 0.35 0.3 5 MD-0111-DXJ-EMXO-10M0000000 10 1 75 11.8 50 ns 2E-12 1.75 0.6 5 MD-0111-DXJ-DAEM-10M0000000 10 1 10 11.8 50 ns 2E-12 1.75 0.6 5 MD-0113-BXJ-OCXO-10M0000000 18 0.2 4 19.5 50 ns 1E-12 4.2 3 12 MD-0113-BXJ-DAOC-10M0000000 18 0.2 0.2 19.5 50 ns 1E-12 4.2 3 12 MD-0114-BXJ-DOCX-10M0000000 18 0.1 0.2 21.3 50 ns 1E-12 14 5.3 12 Phase Noise/ AVAR -10 Hz -100 Hz -1 kHz -10 kHz -100 kHz AVAR (t=1s) AVAR (t=10s) MD-0100-DXJ-TCXO-10M0000000 -95 -120 -140 -155 -155 tbd tbd MD-0102-DXJ-HPTC-10M0000000 -80 -110 -130 -140 -150 tbd tbd MD-0101-DXJ-EMXO-10M0000000 -100 -130 -140 -145 -150 1E-10 5E-10 MD-0101-DXJ-DAEM-10M0000000 -100 -130 -140 -145 -150 1E-10 5E-10 MD-0103-BXJ-OCXO-10M0000000 -120 -135 -145 -145 -145 1E-11 2E-11 MD-0103-BXJ-DAOC-10M0000000 -120 -135 -145 -145 -145 1E-11 2E-11 MD-0104-BXJ-DOCX-10M0000000 -120 -135 -145 -145 -145 1E-11 2E-11 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com 2 Specifications RF Output Waveform Characteristics (via sma) Parameter Min Typical Waveform Output Power Max Units Condition Sinewave +3.0 +9.0 +11.0 dBm 50 Ohm, 12 V supply models +2.0 +5.0 +7.5 dBm 50 Ohm, 5 V supply models Harmonics -30 dBc 50 Ohm Spurious -70 dBc 50 Ohm RF Output Waveform Characteristics (via pin 8) Waveform High Level Output Voltage (VOH) HCMOS 4.5 3.0 Low Level Output Voltage (VOL) Rise/Fall Time Duty Cycle 40 Parameter Min 5.0 VDC <-0.5mA Load, 12 V supply models 3.3 VDC <-0.5mA Load, 5 V supply models 0.0 0.4 VDC <0.5mA Load, 12 V supply models 0.0 0.3 VDC <0.5mA Load, 5 V supply models 3 5 nSec 15 pF 50 60 % 15 pF 1pps Output Characteristics (via SMA and pin 2) Typical Waveform High-level output voltage (VOH) Max Units Condition 5.0 VDC 50 Ohms, 12 V supply models TTL 4.0 2.3 Low-level output voltage (VOL) Pulse Width 3.3 VDC 50 Ohms, 5V supply models 0.0 0.4 VDC 50 Ohms, 12 V supply models 0.0 0.3 VDC 50 Ohms, 5V supply models us default value user programmable 100 ns to 999.9999 ms 10 External 1PPS Reference Input (Pin 1) Waveform High-Level Output Voltage (VOH) TTL 2.4 Low-Level Output Voltage (VOL) Pulse width7 0.0 5.0 VDC 0.4 VDC 10 50 Ohms input impedance uSec Lock Status Indicator (Pin 9)4 Parameter Min Module Locked Module Not Locked Typical Max Units Condition 4.5 5.0 VDC <5mA Load, 12 V supply model 3.0 3.3 VDC <5mA Load, 5V supply model 0 0.5 VDC <5mA Load, 12 V Supply model 0 0.3 VDC <5mA Load, 5V supply model Module Hardware OK Indicator (Pin 10) 5 Module Hardware OK Module Hardware Failure 4.5 5.0 VDC <5mA Load, 12 V supply model 3.0 3.3 VDC <5mA Load, 5V supply model 0 0.5 VDC <5mA Load, 12 V Supply model 0 0.3 VDC <5mA Load, 5V supply model Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com 3 Specifications Module Hardware Reset (Pin 12) 6 Reset Module 0.5 VDC 2 kOhm internal pull up resistance 0.3 VDC 2 kOhm internal pull up resistance Manual Holdover Set (Pin 11) 7 Enter Manual Holdover 0 0.5 VDC 2 kOhm internal pull up resistance 0 0.3 VDC 2 kOhm internal pull up resistance Serial Communications Interface 8 Rx high-level input voltage (VIH) Rx low-level input voltage (VIL) 4.5 5.5 VDC 12 V supply model 3.0 3.3 VDC 5 V supply model -0.5 0.0 0.5 VDC 12 V supply model -0.3 0.0 0.3 VDC 5 V supply model Tx high-level output voltage (VOH) 4.5 5.0 VDC 12 V supply model 3.0 3.3 VDC 5 V supply model Tx low-level output voltage (VOL) -0.5 0.0 0.5 VDC 12 V supply model -0.3 0.0 0.3 VDC 5 V supply model Hz User configurable from 0 to 255 seconds Update rate 1 Communications Protocol Vectron Binary/NMEA 0183 See MD-010/MD-011Command List for Full Details Pulse width7 10 uSec Supply voltage +11.4 +12 +12.6 VDC 12 V supply models +4.75 +5 +5.25 VDC 5 V supply models Supply Voltage (Pin 7,15,16) Absolute Maximum Ratings Supply voltage (VS) Dc voltage on any I/O pin Output load AC ripple 15 VDC 12 V supply models 7.5 VDC 5 V supply models 5.5 V 50 mVpk-pk 10 Ohms 10Hz to 1MHz Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com 4 Detailed Hold Over Specifications (us) Holdover Capability - MD-0110-DXJ-TCXO-10M0000000 Holdover Time ΔT=2 ˚C ΔT=10 ˚C ΔT=20 ˚C ΔT=30 ˚C ΔT=45 ˚C9 1 minute 0.6 2.1 4 6 10 5 minutes 2 10 20 30 45 10 minutes 4.9 20 40 60 85 30 minutes 15 60 120 175 260 1 hour 32 120 240 350 520 Holdover Capability - MD-0112-DXJ-HPTC-10M0000000 Holdover Time ΔT=2 ˚C ΔT=10 ˚C ΔT=20 ˚C ΔT=30 ˚C ΔT=45 ˚C9 1 minute 0.25 0.5 1 1.2 1.7 5 minutes 0.75 2.1 4 5.5 8 10 minutes 1.5 4.3 8 10.8 16 30 minutes 4.8 13 23 33 55 1 hour 12 27 47 66 120 Holdover Capability - MD-0111-DXJ-EMXO-10M0000000 Holdover Time ΔT=2 ˚C ΔT=10 ˚C ΔT=20 ˚C ΔT=30 ˚C ΔT=45 ˚C9 30 minutes 6.5 31 60 95 140 1 hour 12.5 60 120 180 270 4 hours 52 250 480 725 1090 8 hours 105 490 970 1450 2170 24 hours 340 1500 2950 4380 6530 Holdover Capability - MD-0111-DXJ-DAEM-10M0000000 Holdover Time ΔT=2 ˚C ΔT=10 ˚C ΔT=20 ˚C ΔT=30 ˚C ΔT=45 ˚C9 30 minutes 1 4.5 8.2 12.3 19 1 hour 2 8.7 17 25 37 4 hours 8.5 34 70 100 150 8 hours 20 75 140 200 295 24 hours 90 240 440 630 920 ΔT=30 ˚C ΔT=45 ˚C9 Holdover Capability - MD-0110-DXJ-OCXO-10M0000000 Holdover Time ΔT=2 ˚C ΔT=10 ˚C ΔT=20 ˚C 30 minutes 0.45 1.8 3.4 5 7.4 1 hour 0.9 4 6.6 10 15 4 hours 3.6 14 27 40 60 8 hours 8 30 55 80 120 24 hours 32 100 170 250 360 Holdover Time ΔT=2 ˚C ΔT=10 ˚C ΔT=20 ˚C ΔT=30 ˚C ΔT=45 ˚C9 30 minutes 0.12 0.2 0.3 0.35 0.5 1 hour .24 0.4 0.5 1 1 4 hours 1 1.6 2.3 3 3.9 8 hours 4.5 3.7 5 3.5 8.2 24 hours 18 21 23 25 32 Holdover Capability - MD-0110-DXJ-DAOC-10M0000000 Holdover Capability - MD-0110-DXJ-DOCX-10M0000000 Holdover Time ΔT=2 ˚C ΔT=10 ˚C ΔT=20 ˚C ΔT=30 ˚C ΔT=45 ˚C9 30 minutes 0.05 0.11 0.19 0.27 0.4 1 hour .09 0.21 0.38 0.54 0.77 4 hours 0.4 0.91 1.54 2.2 3.1 8 hours 1.03 2 3.4 4.7 6.8 24 hours 5.9 9 12.8 17 23 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com 5 Specifications Environmental Conditions Parameter Min Operating temperature Max Units Condition see ordering information for avaialble ranges Humidity @ 40˚C Storage Temperature Typical -55 90 % +125 ˚C Reliability VI qualification includes aging various extreme temperatures, shock and vibration, temperature cycling, and IR reflow simulation. The MD-011 family is capable of meeting the following qualification tests: Environmental Compliance Parameter Conditions Mechanical shock MIL-STD-202, Method 213 condition B Mechanical vibration MIL-STD-202, Method 204 condition A Resistance to solvents MIL-STD-202, Method 215 Package Outline Handling Precautions Although ESD protection circuitry has been designed into the MD-011 proper precautions should be taken when handling and mounting. VI employs a human body model (HBM) and a charged-device model (CDM) for ESD susceptibility testing and design protection evaluation. ESD Ratings Model Minimum Conditions Human body model 1500 V MIL-STD-833, Method 3015 Charged device model 1000 V JEDEC, JESD22-C101 Package Outline 16 Pin I/O Connections Number oscillator height Name Description 1 PPS In External 1 PPS Input 2 PPS Out 1 PPS Output 3 Ground Ground 4 Ground Ground 5 Rx Serial Communications Receive 6 Tx Serial Communications Transmit 7 Vcc Power Supply 8 RF Out RF HCMOS Output 9 Locked Logic-high = Output locked to GPS 10 Module OK Logic low = Failure with module operation 11 ManHold Manual Holdover Input 12 Reset Hardware reset 13 Ground Ground 14 Ground Ground Notes: 15 Vcc Power Supply • RF and 1pps input and output connectors are MCX type (SMA, SMB, MMCX connectors 16 Vcc Power Supply require additional part numbers). • Keyed connector is Samtec FTSH-108-01LDVK type. • Dimensions: mm • Module height in part number is the sum of oscillator height, board, and clearance • Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com 6 Accessories Vectron Partnumber Description MD-010-EK MD-010X-XXX-XXXX Module with Evaluation Kit C6001A1-0001 GPS Timing Antenna, Active, +5Vdc C6001A1-0002 Antenna Cable, 10 meter length, N-Plug to SMA Plug Ordering Information Instructions The MD-010 series of GPS disciplined oscillators has multiple options with embedded OCXOs, Double OCXOs, EMXOs and TCXOs. Options are created to optimize customer hold over requirements while meeting pricing needs. Customization to unique customer requirements is available and is common for this level of integration. Common customizations include alternate output frequencies, temperature ranges, differing values and methods of hold over specification, and holdover optimization in the frequency domain. . Not all combinations of codes are available. The table below lists exisiting combinations available as of the date of publication of this data sheet. Please contact the factory for additional options. Ordering Information MD - 010 3 - B X J - OCXO - 10M0000000 Frequency Product Family MD: Precision Modules Embedded Oscillator TCXO (Temperature Compensated XO) HPTC (High Precision TCXO) EMXO (Evacuated Miniaturized Oven Controlled XO) DAEM (Digitally Assisted EMXO) OCXO (Oven Controlled XO) DAOC (Digitally Assisted OCXO) DOCX (Double Oven Controlled XO) Package 65x115mm Height 0: 11 mm 1: 11.8 mm 2: 13 mm 3: 19.5 mm 4: 21.3mm 5: 25 mm 6: 30 mm Supply Voltage A: + 15V B: +12V D: +5V RF Output Code X: standard outputs per specification Temperature Range D: -40°C to +70°C E: -40°C to +85°C J: -20°C to +70°C T: 0°C to +70°C Available Models (standard models highlighted) MD-0100-DXD-TCXO-10M0000000 MD-0102-DXD-HPTC-10M0000000 MD-0101-DXD-EMXO-10M0000000 MD-0100-DXE-TCXO-10M0000000 MD-0102-DXE-HPTC-10M0000000 MD-0101-DXE-EMXO-10M0000000 MD-0100-DXJ-TCXO-10M0000000 MD-0102-DXJ-HPTC-10M0000000 MD-0101-DXJ-EMXO-10M0000000 MD-0100-DXT-TCXO-10M0000000 MD-0102-DXT-HPTC-10M0000000 MD-0101-DXT-EMXO-10M0000000 MD-0101-DXD-DAEM-10M0000000 MD-0103-DXD-OCXO-10M0000000 MD-0103-DXD-DAOC-10M0000000 MD-0101-DXE-DAEM-10M0000000 MD-0103-DXE-OCXO-10M0000000 MD-0103-DXE-DAOC-10M0000000 MD-0101-DXJ-DAEM-10M0000000 MD-0103-DXJ-OCXO-10M0000000 MD-0103-DXJ-DAOC-10M0000000 MD-0101-DXT-DAEM-10M0000000 MD-0103-DXT-OCXO-10M0000000 MD-0103-DXT-DAOC-10M0000000 MD-0103-BXJ-OCXO-10M0000000 MD-0103-BXT-OCXO-10M0000000 MD-0104-DXJ-DOCX-10M0000000 MD-0104-DXT-DOCX-10M0000000 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com 7 Notes 1) 2) Holdover and aging performance is after 7 days of power-on time. Temperature stabilities apply to -20 to +70 ˚C modules. For other temperatures the temperature stability will vary, however the hold over values over defined temperature ranges remain constant. 3) 24 hour average when locked to external 1PPS 4) The status locked indicator is intended to indicate when the module is fully locked to external 1 pps. 5) The Hardware OK indicator is intended to indicate when the module is operating properly without any failures including hardware, software or parameter out of range, see protocol. 6) Open collector input bit. 7) If the minimum supply current is not exceeded, the Antenna Open Flag will be set. Over current will be set if maximum is exceeded. Circuit has overcurrent protection. 8) The Rx pin is the serial interface input and the Tx pin is the serial interface output. The serial interface shall operate at 9600 baud with eight (8) data bits, one (1) stop bit and no parity. 9) This holdover performance also applies to the temperature deviation over the entire operating range of -20 to +70˚C. Application Notes 1) 2) 3) Holdover Contributions and Calculations - please contact for a copy Vectron Discipline and Hold Over Process and Algorithms - please contact us for a copy Utilizing Disciplined Oscillators as Frequency References - please contact factory For Additional Information, Please Contact 8 USA: Vectron International 267 Lowell Road Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 Europe: Vectron International Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 7268.801.100 Fax: +49 (0) 7268.801.282 Asia: Vectron International 1F-2F, No 8 Workshop, No 308 Fenju Road WaiGaoQiao Free Trade Zone Pudong, Shanghai, China 200131 Tel: 86.21.5048.0777 Fax: 86.21.5048.1881 Disclaimer Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Rev: 100509 dmc Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com 8