Maxim MAX619ESA Regulated 5v charge-pump dc-dc converter Datasheet

19-0227; Rev 2; 5/96
NUAL
KIT MA
ATION
EET
H
S
A
EVALU
T
WS DA
FOLLO
Regulated 5V Charge-Pump
DC-DC Converter
____________________________Features
♦ Regulated 5V ±4% Charge Pump
♦ Output Current Guaranteed over Temperature
20mA (VIN ≥ 2V)
50mA (VIN ≥ 3V)
♦ 2V to 3.6V Input Range
♦ No Inductors; Very Low EMI Noise
♦ Ultra-Small Application Circuit (0.1in2)
♦ Uses Small, Inexpensive Capacitors
♦ 500kHz Internal Oscillator
♦ Logic-Controlled 1µA Max Shutdown
Supply Current
♦ Shutdown Disconnects Load from Input
♦ 8-Pin DIP and SO Packages
________________________Applications
Two Battery Cells to 5V Conversion
_______________Ordering Information
PART
Local 3V-to-5V Conversion
TEMP. RANGE
PIN-PACKAGE
MAX619CPA
0°C to +70°C
8 Plastic DIP
MAX619CSA
0°C to +70°C
8 SO
MAX619C/D
0°C to +70°C
MAX619EPA
-40°C to +85°C
8 Plastic DIP
Minimum Component DC-DC Converters
MAX619ESA
-40°C to +85°C
8 SO
Remote Data-Acquisition Systems
MAX619MJA
-55°C to +125°C
8 CERDIP
Portable Instruments & Handy-Terminals
Battery-Powered Microprocessor-Based Systems
5V Flash Memory Programmer
Compact 5V Op-Amp Supply
Dice*
* Dice are specified at TA = +25 °C.
Regulated 5V Supply from Lithium Backup Battery
Switching Drive Voltage for MOSFETs in
Low-Voltage Systems
__________________Pin Configuration
__________Typical Operating Circuit
TOP VIEW
INPUT
2V to 3.6V
10µF
C1+ 1
7 SHDN
MAX619
C2+ 4
DIP/SO
OUTPUT
5V, 20mA
MAX619
ON/OFF
SHDN
C1+
6 GND
5 C2-
OUT
10µF
8 C1-
IN 2
OUT 3
IN
C2+
0.22µF
0.22µF
C1-
GND
C2-
________________________________________________________________ Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800
MAX619
_______________General Description
The MAX619 step-up charge-pump DC-DC converter
delivers a regulated 5V ±4% output at 50mA over temperature. The input voltage range is 2V to 3.6V (two
battery cells).
The complete MAX619 circuit fits into less than 0.1in2 of
board space because it requires only four external
capacitors: two 0.22µF flying capacitors, and 10µF
capacitors at the input and output.
Low operating supply current (150µA max) and low
shutdown supply current (1µA max) make this device
ideal for small, portable, and battery-powered applications. When shut down, the load is disconnected from
the input.
The MAX619 is available in 8-pin DIP and SO packages.
MAX619
Regulated 5V Charge-Pump
DC-DC Converter
ABSOLUTE MAXIMUM RATINGS
VIN to GND ............................................................-0.3V to +5.5V
VOUT to GND .........................................................-0.3V to +5.5V
SHDN to GND ..............................................-0.3V to (VIN + 0.3V)
IOUT Continuous (Note 1)..................................................120mA
Continuous Power Dissipation (TA = +70°C)
Plastic DIP (derate 9.09mW/°C above +70°C) ............727mW
SO (derate 5.88mW/°C above +70°C) .........................471mW
CERDIP (derate 8.00mW/°C above +70°C) .................640mW
Operating Temperature Ranges
MAX619C_ _ .......................................................0°C to +70°C
MAX619E_ _ ....................................................-40°C to +85°C
MAX619MJA ..................................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +165°C
Lead Temperature (soldering, 10sec) .............................+300°C
Note 1: The MAX619 is not short-circuit protected.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VIN = 2V to 3.6V, C1 = C2 = 0.22µF, C3 = C4 = 10µF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
Input Voltage
SYMBOL
CONDITIONS
VIN
MIN
TYP
2
MAX
UNITS
3.6
V
5.2
V
2.0V ≤ VIN ≤ 3.6V, 0mA ≤ IOUT ≤ 20mA
Output Voltage
VOUT
3.0V ≤ VIN ≤ 3.6V, 0mA ≤ IOUT ≤ 50mA, MAX619C
3.0V ≤ VIN ≤ 3.6V, 0mA ≤ IOUT ≤ 45mA, MAX619E
4.8
5.0
3.0V ≤ VIN ≤ 3.6V, 0mA ≤ IOUT ≤ 40mA, MAX619M
Output Ripple
No-Load Supply Current
VRIPPLE
IIN
Eff
Switching Frequency
SHDN Input Threshold
SHDN Input Current
2
100
2V ≤ VIN ≤ 3.6V, IOUT = 0mA
2V ≤ VIN ≤ 3.6V, IOUT = 0mA,
VSHDN = VIN
Shutdown Supply
Current
Efficiency
No load to full load
MAX619C/E
170
µA
0.02
1
µA
10
MAX619M
VIN = 3V, IOUT = 20mA
82
VIN = 3V, IOUT = 30mA
82
VIN = 2V, IOUT = 20mA
80
At full load
%
500
VIH
kHz
0.7 x VIN
VIL
IIH
mV
75
0.4
VSHDN = VIN
MAX619C/E
±1
MAX619M
±10
________________________________________________________________________________________
V
µA
Regulated 5V Charge-Pump
DC-DC Converter
EFFICIENCY vs. OUTPUT CURRENT
AND INPUT VOLTAGE
200
VIN = 1.8V
75
VIN = 3.3V
E
B
120
100
80
VIN = 3.6V
70
A
B
C
D
E
F
G
A
60
VIN = 2.4V
40
65
VIN = 2.7V
100
C
140
VIN = 2.0V
IIN (mA)
EFFICIENCY (%)
80
SHDN = 0V
F
160
VIN = 3.0V
1000
G
D
180
20
VIN
IOUT
1.8
2.0
2.4
2.7
3.0
3.6
3.3
18
36
41
64
72
94
100
MAX
IIN (µA)
90
85
NO-LOAD INPUT CURRENT
vs. INPUT VOLTAGE
INPUT CURRENT vs. OUTPUT CURRENT
1.0
1
10
IOUT (mA)
100
SHDN = VIN
0.1
0.01
1.5
0
60
10
0 10 20 30 40 50 60 70 80 90 100
2.0
2.5
3.0
5.06
90
5.04
85
3.6V
V= IN
= 3.6V
EFFICIENCY (%)
VOUT (V)
VOUT (V)
IOUT = 20mA
5.02
4.95
4.90
VIN = 1.8V
VIN = 2.0V
4.85
5.00
4.98
VIN = 2.4V, 2.7V
VIN = 3.0V
4.80
4.96
10
100
80
75
70
65
4.94
4.75
1
4.5
IOUT = 10mA
VIN = 3.3V
5.00
4.0
EFFICIENCY vs. INPUT VOLTAGE
OUTPUT VOLTAGE vs. INPUT VOLTAGE
OUTPUT VOLTAGE vs. OUTPUT CURRENT
5.05
3.5
VIN (V)
IOUT (mA)
60
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
1.5
2.0
2.5
VIN (V)
IOUT (mA)
LOAD-TRANSIENT RESPONSE
2ms/div
TOP TRACE: OUTPUT CURRENT, 0mA to 25mA, 10mA/div
BOTTOM TRACE: OUTPUT VOLTAGE, 5mV/div, AC-COUPLED
3.0
3.5
4.0
VIN (V)
LINE-TRANSIENT RESPONSE (IOUT = 20mA)
2ms/div
RLOAD = 250Ω, VOUT = 5V, IOUT = 20mA
TOP TRACE: VIN = 2V to 3V, 1V/div
BOTTOM TRACE: OUTPUT VOLTAGE, 50mV/div, AC-COUPLED
________________________________________________________________________________________
3
MAX619
__________________________________________Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
MAX619
Regulated 5V Charge-Pump
DC-DC Converter
_____________________Pin Description
PIN NAME
FUNCTION
1
C1+
Positive Terminal for C1
2
IN
3
OUT
+5V Output Voltage. VOUT = 0V when in
shutdown mode.
4
C2+
Positive Terminal for C2
5
C2-
Negative Terminal for C2
6
GND
Ground
7
SHDN
Active-High CMOS Logic-Level Shutdown Input
8
C1-
Input Supply Voltage
Negative Terminal for C1
_______________Detailed Description
Operating Principle
The MAX619 provides a regulated 5V output from a 2V
to 3.6V (two battery cells) input. Internal charge pumps
and external capacitors generate the 5V output, eliminating the need for inductors. The output voltage is
regulated to 5V ±4% by a pulse-skipping controller that
turns on the charge pump when the output voltage
begins to droop.
To maintain the greatest efficiency over the entire input
voltage range, the MAX619’s internal charge pump
operates as a voltage doubler when VIN ranges from
3.0V to 3.6V, and as a voltage tripler when VIN ranges
from 2.0V to 2.5V. When VIN ranges from 2.5V to 3.0V,
4
the MAX619 switches between doubler and tripler
mode on alternating cycles, making a 2.5 x VIN charge
pump. To further enhance efficiency over the input
range, an internal comparator selects the higher of VIN
or V OUT to run the MAX619’s internal circuitry.
Efficiency with VIN = 2V and IOUT = 20mA is typically
80%.
Figure 1 shows a detailed block diagram of the
MAX619. In tripler mode, when the S1 switches close,
the S2 switches open and capacitors C1 and C2
charge up to VIN. On the second half of the cycle, C1
and C2 are connected in series between IN and OUT
when the S1 switches open and the S2 switches close,
as shown in Figure 1. In doubler mode, only C2 is
used.
During one oscillator cycle, energy is transferred from
the input to the charge-pump capacitors, and then
from the charge-pump capacitors to the output capacitor and load. The number of cycles within a given time
frame increases as the load increases or as the input
supply voltage decreases. In the limiting case, the
charge pumps operate continuously, and the oscillator
frequency is nominally 500kHz.
Shutdown Mode
The MAX619 enters low-power shutdown mode when
SHDN is a logic high. SHDN is a CMOS-compatible
input. In shutdown mode, the charge-pump switching
action is halted, OUT is disconnected from IN, and
VOUT falls to 0V. Connect SHDN to ground for normal
operation. When VIN = 3.6V, VOUT typically reaches
5V in 0.5ms under no-load conditions after SHDN goes
low.
________________________________________________________________________________________
Regulated 5V Charge-Pump
DC-DC Converter
MAX619
IN
C3
10µF
MAX619
P
IC
POWER
S1A
C2+
*
P
OUT
S2A
C4
C2
0.22µF
IN
S1B
C2-
VIN/VOUT
CONTROL
LOGIC
S2B
C1+
10µF
FB
SWITCH
CONTROL
BUS
VREF
S1C
C1
0.22µF
SHDN
SD
S2C
C1S1D
GND
*
SWITCHES SHOWN IN TRIPLER MODE, DISCHARGE CYCLE
Figure 1. Block Diagram
________________________________________________________________________________________
5
MAX619
Regulated 5V Charge-Pump
DC-DC Converter
__________Applications Information
Capacitor Selection
Charge-Pump Capacitors C1 and C2
The values of charge-pump capacitors C1 and C2 are
critical to ensure adequate output current and avoid
excessive peak currents. Use values in the range of
0.22µF to 1.0µF. Larger capacitors (up to 50µF) can
be used, but larger capacitors will increase output ripple. Ceramic or tantalum capacitors are recommended.
When using ceramic capacitors, the values of C3 and
C4 can be reduced to 2µF and 1µF, respectively. If the
input supply source impedance is very low, C3 may not
be necessary.
Many capacitors exhibit 40% to 50% variation over
temperature. Compensate for capacitor temperature
coefficient by selecting a larger nominal value to
ensure proper operation over temperature. Table 1 lists
capacitor suppliers.
Input and Output Capacitors, C3 and C4
The type of input bypass capacitor (C3) and output filter capacitor (C4) used is not critical, but it does affect
performance. Tantalums, ceramics, or aluminum electrolytics are suggested. For smallest size, use Sprague
595D106X0010A2 surface-mount capacitors, which
measure 3.7mm x 1.8mm (0.146in x 0.072in). For lowest ripple, use large, low effective-series-resistance
(ESR) ceramic or tantalum capacitors. For lowest cost,
use aluminum electrolytic or tantalum capacitors.
Figure 2 shows the component values for proper operation using minimal board space. The input bypass
capacitor (C3) and output filter capacitor (C4) should
both be at least 10µF when using aluminum electrolytics or Sprague’s miniature 595D series of tantalum chip
capacitors.
1
C2
0.22µF
8
2
6
2
CELLS
4
C2+
C1+
MAX619
C1–
IN
GND
5
C2–
7
SHDN
OUT
C1
0.22µF
3
C3
10µF
5V ±4%
@ 20mA
C4
10µF
Figure 2. Two-Cell to 5V Application Circuit
Table 1. Capacitor Suppliers
SUPPLIER
Murata Erie
Sprague Electric
(smallest size)
PHONE NUMBER
(814) 237-1431
(603) 224-1961
(207) 327-4140
FAX NUMBER
(814) 238-0490
(603) 224-1430
(207) 324-7223
CAPACITOR
CAPACITOR TYPE*
GRM42-6Z5U10M50
0.1µF ceramic (SM)
GRM42-6Z5U22M50
0.22µF ceramic (SM)
RPI123Z5U105M50V
1.0µF ceramic (TH)
RPE121Z5U104M50V
0.1µF ceramic (TH)
595D106X0010A2
10µF tantalum (SM)
* Note: (SM) denotes surface-mount component, (TH) denotes through-hole component.
6
________________________________________________________________________________________
Regulated 5V Charge-Pump
DC-DC Converter
___________________Chip Topography
Paralleling Devices
Two MAX619s can be placed in parallel to increase
output drive capability. The IN, OUT, and GND pins
can be paralleled, but C1 and C2 pins cannot. The
input bypass capacitor and output filter capacitor are,
to some extent, shared when two circuits are paralleled. If the circuits are physically close together, it
may be possible to use a single bypass and a single
output capacitor, each with twice the value of the single
circuit. If the MAX619s cannot be placed close together, use separate bypass and output capacitors. The
amount of output ripple observed will determine
whether single input bypass and output filter capacitors
can be used.
C1+
C1-
SHDN
IN
0.115”
(2.921mm)
OUT
GND
C2+
C20.072”
(1.828mm)
TRANSISTOR COUNT: 599;
SUBSTRATE CONNECTED TO GND.
MAX619
OUT
IN
GND
INPUT
5V, 40mA
MAX619
OUT
IN
GND
Figure 3. Paralleling Two MAX619s
________________________________________________________________________________________
7
MAX619
Layout Considerations
The MAX619’s high oscillator frequency makes good
layout important. A good layout ensures stability and
helps maintain the output voltage under heavy loads.
For best performance, use very short connections to
the capacitors.
Similar pages