HI-8190H, HI-8191H, HI-8192H July 2013 12W, Quad, SPST, 3.3V / 5.0V compatible Analog Switch with High Operating Temperature GENERAL DESCRIPTION FEATURES The HI-8190H family are quad analog CMOS switches fabricated with Silicon-on-Insulator (SOI) technology for latch-up free operation and maximum switch isolation. They are optimized for use in high temperature avionics applications. The devices are capable of operating at extended temperature ranges of -55°C to 175°C for plastic packages and -55°C to 200°C for the ceramic CERDIP-16 package. · Extended Temperature Ranges The switch voltages can range from bipolar ± 3.3V to ± 15V or single ended from 3.3V to 15V. The logic supply can range from 3.3V to 5.0V. The HI-8190H provides four each normally open switches when the switch control inputs are Low. The HI-8191H provides four each normally closed switches when the switch control inputs are Low. The HI-8192H provides a combination of two normally On and two normally Off switches. The limits of the operating range are defined by the V+/V- bias voltage (railto-rail switching capability). On-resistance of each switch depends upon only the VLOGIC selection. At 5V, RON ranges from 10W to 17W while at 3.3V supply RON ranges from 10W to 22W. Each switch is designed using back to back high voltage transistors. Switch transistors are symmetrical and conduct equally well in either direction. Signal range can run the full rails. Off leakages are very low (1 nA typical) and charge injection is less than 3 pC. Switch ESD tolerance is greater than 4 KV. The Off state is achieved first before any On condition is applied. Switching times with a 3.3V VLOGIC supply are typically 35 ns to the On state and 20 ns to the Off state. APPLICATIONS · Down-hole drilling and oil exploration · High temperature avionics · Data bus isolation · Data Acquisition Systems · Engine controllers (FADEC) (DS8190H Rev. New) · -55°C to 175°C (plastic packages) · -55°C to 200°C (ceramic CERDIP-16 package) · ± 3.3V to ± 15V CMOS analog switches · Low RON: 12 W to 15 W typical · Robust CMOS Silicon-on-Insulator (SOI) technology · SOI switch isolation with 1nA typical Off leakage · Superior ESD protection > 4KV HBM · Fast switching time with break-before-make · Low power PIN CONFIGURATIONS (Top Views) IN1 1 16 IN2 S1A 2 15 S2A S1B 3 14 S2B V- 4 13 V+ GND 5 12 VLOGIC S4B 6 11 S3B S4A 7 10 S3A IN4 8 9 IN3 HI-8190PSH, 16-Pin SOIC PRODUCT OPTIONS PART TYPE IN1 HI-8190H 0 1 HI-8191H 0 1 HI-8192H 0 1 HOLT INTEGRATED CIRCUITS www.holtic.com Switch 1 Open Closed Closed Open Open Closed IN2 0 1 0 1 0 1 Switch 2 Open Closed Closed Open Closed Open IN3 0 1 0 1 0 1 Switch 3 Open Closed Closed Open Closed Open IN4 0 1 0 1 0 1 Switch 4 Open Closed Closed Open Open Closed 07/13 HI-8190H, HI-8191H, HI-8192H PIN DESCRIPTIONS SIGNAL FUNCTION IN1 S1A S1B VGND S4B S4A IN4 IN3 S3A S3B VLOGIC V+ S2B S1B IN2 Logic Input Switch Node Switch Node Supply Supply Switch Node Switch Node Logic Input Logic Input Switch Node Switch Node Supply Supply Switch Node Switch Node Logic input DESCRIPTION HI-8190H and HI-8192H are normally Open when input Low Switch 1 Node Switch 1 Node Negative supply for Bipolar configuration. GND for Unipolar use Reference Ground Switch 4 Node Switch 4 Node HI-8190H and HI-8192H are normally Open when input Low HI-8191H and HI-8192H are normally Closed when input Low Switch 3 Node Switch 3 Node 3.3V or 5.0V Logic supply Positive supply for Bipolar and Unipolar configurations Switch 2 Node Switch 2 Node HI-8191H and HI-8192H are normally Closed when input Low 24W 24W 22W 22W T = +200°C VLOGIC = 3.3V 18W 16W VLOGIC = 5.0V 18W T = +25°C 16W T = -55°C 14W 14W 12W 12W 10W 10W 8W -15V -10V -5V T = +125°C 20W RON RON 20W 0V 5V 10V 15V 8W -15V -10V VSWITCH Typical RON as a function of VLOGIC and VSWITCH (10mA switch current, 25°C) -5V 0V VSWITCH 5V 10V Typical RON as a function of VSWITCH and Temperature (10mA switch current) VLOGIC = 5V HOLT INTEGRATED CIRCUITS 2 15V HI-8190H, HI-8191H, HI-8192H ABSOLUTE MAXIMUM RATINGS (Voltages referenced to GND = 0V) Supply Voltage, V+: ............................................................................16.5V Operating Temperature Range: (Plastic) ........................ -55°C to +175°C Supply Voltage, V-:.............................................................................-16.5V (Ceramic) ...................... -55°C to +200°C Supply Volgate, VLOGIC .........................................................................5.5V Switch Current (either direction, DC): .................................................20mA Peak Switch Current (1 ms pulse, 10% duty cycle max.)..................100mA Storage Temperature Range: ......................................-65°C to +150°C Digital Input Voltage (IN1-4):.....................................-0.3V to VLOGIC + 0.3V Reflow Soldering Temperature: .......................................... +260°C Max. NOTE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS V+ = 15V, V- = -15V, GND = 0V. Operating temperature range (unless otherwise noted). VLOGIC = 3.3V PARAMETER SYMBOL CONDITIONS FIGURE MIN TYP MAX VLOGIC = 5.0V MIN TYP MAX UNIT SWITCH PARAMETERS Switch Signal Range Switch Resistance Leakage VRANGE -15 +15 V 10 8 17 26 W W 5 5 nA 2 20 20 nA Switch voltage ± 15V, 200°C 2 5 5 µA Switch voltage ± 15V, -55°C 2 150 150 nA RON 25°C, 10mA -55°C to +125°C, 10mA 1 1 |ISWLEAK| Switch voltage ± 15V, 25°C 2 |ISWLEAK| Switch voltage ± 15V, 125°C |ISWLEAK| |ISWLEAK| 10 8 22 26 LOGIC INPUTS Input High Voltage VIH 70 70 %VLOGIC Input Low Voltage VIL Input Current IIN VIN = 0V or VIN=VLOGIC VLOGIC Current IDD1 Any state 2.0 4.0 µA V+ Current IDD2 Any state 2.0 2.0 µA V- Current IEE Any state TON V+/V- = ±10V, 25°C VS = ±10V, -55°C to +125°C 3 3 55 V+/V- = ±10V, 25°C VS = ±10V, -55°C to +125°C 3 3 35 10V signal, 25°C 10V signal, -55°C to +125°C 4 4 30 -0.5 0.5 30 -0.5 0.5 %VLOGIC µA SUPPLY -2.0 µA -2.0 DYNAMIC PARAMETERS Turn On Time Turn Off time Break-Before-Make Time TOFF TD 35 75 ns ns 25 ns ns 20 40 8 4 55 8 ns ns 4 Charge Injection Q VS=0V, RS=0W, 25°C 5 4 4 pC Off Isolation RR f = 1 MHz, 25°C 6 65 65 dB Crosstalk CR f = 1 MHz, 25°C 7 90 90 dB COFF CON Switch Off, 25°C Switch On, 25°C 8 9 5 20 5 20 pF pF Capacitance HOLT INTEGRATED CIRCUITS 3 HI-8190H, HI-8191H, HI-8192H TEST CIRCUITS IDS V1 SA VS + - RON = V1/IDS + - VS Figure 1 - On Resistance +5V 0.1µF 0.1µF VIN (HI-8191) V+ SA VD + - Figure 2 - Off Leakage +15V VLOGIC ID(OFF) SB A IS(OFF) SA A SB 50% 50% 50% 50% VIN (HI-8190) SB VOUT IN VS GND + - 90% 300W 35pF V- 50% VOUT 0.1µF -15V t ON t OFF Figure 3. Switching Times 0.1µF +5V +15V VLOGIC V+ 0.1µF 5V VIN 50% 50% 0V VS1 VS2 S1A S1B S2A S2B IN VOUT1 VOUT2 35pF GND V- 35pF 0.1µF 90% 50% VOUT1 300W 300W 90% VOUT2 50% -15V tD Figure 4. Break-Before-Make Time Delay (HI-8192H) HOLT INTEGRATED CIRCUITS 4 tD HI-8190H, HI-8191H, HI-8192H RS +5V +15V VLOGIC V+ SA SB VOUT VIN IN VS GND + - CL 10nF V- DVOUT VOUT -15V QINJ = CL x DVOUT Figure 5. Charge Injection 0.1µF 0.1µF +5V +15V VLOGIC 0.1µF +15V VLOGIC V+ SA1 V+ SA +5V SB VOUT 0.1µF SB1 50W IN1 VS IN IN2 GND 50W V- VS 0.1µF SB2 VOUT 50W -15V SA2 GND NC V0.1µF -15V Figure 7 - Channel-to-Channel Crosstalk Figure 6 - Off Isolation 0.1µF +5V +15V VLOGIC V+ SA Capacitance Meter f=1MHz 0.1µF 0.1µF SB +15V VLOGIC V+ SA Capacitance Meter f=1MHz IN GND +5V V- SB VS IN GND V- 0.1µF 0.1µF -15V -15V Figure 8 - Off Capacitance Figure 9 - On Capacitance HOLT INTEGRATED CIRCUITS 5 0.1µF HI-8190H, HI-8191H, HI-8192H FREQUENCY RESPONSE Figure 10 shows a typical frequency response. Frequency Response 0.0 -1.0 LOSS (dB) -2.0 -3.0 -4.0 -5.0 -6.0 -7.0 0 1 10 Frequency (MHz) Figure 10. Frequency Response. HOLT INTEGRATED CIRCUITS 6 100 HI-8190H, HI-8191H, HI-8192H ORDERING INFORMATION HI - 819x PS H F PART NUMBER F PART NUMBER PS PART NUMBER LEAD FINISH 100% Matte Tin (Pb-free, RoHS compliant) PACKAGE DESCRIPTION o o 16 PIN PLASTIC NARROW BODY SOIC (16HN): -55 C to +175 C. FUNCTION 8190 QUAD SWITCH, NORMALLY OPEN 8191 QUAD SWITCH, NORMALLY CLOSED 8192 QUAD SWITCH, TWO NORMALLY OPEN, TWO NORMALLY CLOSED HI - 819x CR H PART NUMBER CR PART NUMBER PACKAGE DESCRIPTION o o 16 PIN CERDIP (16D) not available Pb-free: -55 C to +200 C. FUNCTION 8190 QUAD SWITCH, NORMALLY OPEN 8191 QUAD SWITCH, NORMALLY CLOSED 8192 QUAD SWITCH, TWO NORMALLY OPEN, TWO NORMALLY CLOSED HOLT INTEGRATED CIRCUITS 7 HI-8190, HI-8191, HI-8192 REVISION HISTORY P/N Rev DS8190H New Date 07/23/13 Description of Change Initial release HOLT INTEGRATED CIRCUITS 8 HI-8190 PACKAGE DIMENSIONS inches (millimeters) 16-PIN PLASTIC SMALL OUTLINE (SOIC) - NB (Narrow Body) .0087 ± .0012 (.220 ± .029) .390 ± .004 (9.90 ± .10) .236 ±.008 (5.99 ±.20) Package Type: 16HN .1525 ± .0025 (3.87 ± .06) Top View See Detail A .0165 ± .003 (.419 ± .089) .061 ± .007 (1.549 ± .178) .050 BSC (1.27) 0° to 8° .0069 ± .0029 (.176 ± .074) .033 ± .017 (.838 ± .432) BSC = “Basic Spacing between Centers” is theoretical true position dimension and has no tolerance. (JEDEC Standard 95) Detail A inches (millimeters) 16-PIN CERDIP Package Type: 16D .050 max (1.27 max) .790 max (20.006 max) .005 min (.127 min) .288 ±.005 (7.315 ±.125) .056 typ (1.422 typ) .100 BSC (2.54) .310 ±.010 (7.874 ±.254) .180 max (4.572 max) .200 max (5.080 max) .015 min (.381 min) .125 min (3.175 min) .018 ±.003 (.457 ±.760) 0° to 15° BSC = “Basic Spacing between Centers” is theoretical true position dimension and has no tolerance. (JEDEC Standard 95) HOLT INTEGRATED CIRCUITS 9 .010 ±.002 (.254 ±.051)