NC7WZ14 TinyLogic® UHS Dual Inverter with Schmitt Trigger Inputs Features Description Ultra-High Speed: tPD 3.2ns (Typical) into 50pF at 5V VCC High Output Drive: ±24mA at 3V VCC Power Down High Impedance Inputs/Outputs The NC7WZ14 is a dual inverter with Schmitt trigger input from Fairchild's Ultra-High Speed (UHS) Series of TinyLogic. The device is fabricated with advanced CMOS technology to achieve ultra-high speed with high output drive while maintaining low static power dissipation over a very broad VCC operating range. The device is specified to operate over the 1.65V to 5.5V VCC range. The inputs and outputs are high-impedance when VCC is 0V. Inputs tolerate voltages up to 7V independent of VCC operating voltage. Schmitt trigger inputs achieve typically 1V hysteresis between the positive-and negative-going input threshold voltage at 5V. Proprietary Noise/EMI Reduction Circuitry Broad VCC Operating Range: 1.65V to 5.5V Matches Performance of LCX when Operated at 3.3V VCC Over-Voltage Tolerance Inputs Facilitate 5V to 3V Translation Ultra-Small MicroPak™ Packages Space-Saving SC70 Package Ordering Information Operating Temperature Top Mark NC7WZ14P6X -40 to +85°C Z14 6-Lead SC70, EIAJ SC-88a, 1.25mm Wide 3000 Units on Tape & Reel NC7WZ14EP6X -40 to +125°C Z14 6-Lead SC70, EIAJ SC-88a, 1.25mm Wide 3000 Units on Tape & Reel NC7WZ14L6X -40 to +85°C A9 6-Lead MicroPak™, 1.00mm Wide 5000 Units on Tape & Reel NC7WZ14FHX -40 to +85°C A9 6-Lead, MicroPak2, 1x1mm Body, .35mm Pitch 5000 Units on Tape & Reel Part Number © 1999 Fairchild Semiconductor Corporation NC7WZ14 • Rev. 1.0.7 Package Packing Method www.fairchildsemi.com NC7WZ14 — TinyLogic® UHS Dual Inverter with Schmitt Trigger Inputs June 2011 IEEC/IEC Figure 1. Logic Symbol Pin Configurations Figure 2. SC70 (Top View) A1 1 6 Y1 GND 2 5 VCC A2 3 4 Y2 Figure 3. MicroPak (Top Through View) AAA Pin One Notes: 1. AAA represents Product Code Top Mark (see ordering code). 2. Orientation of Top Mark determines Pin One location. Read the top product code mark left to right. Pin One is the lower left pin. Figure 4. SC70 Pin 1 Orientation NC7WZ14 — TinyLogic® UHS Dual Inverter with Schmitt Trigger Inputs Connection Diagrams Pin Definitions Pin # SC70 Pin # MicroPak Name Description 1 1 A1 2 2 GND 3 3 A2 Input 4 4 Y2 Output 5 5 VCC Supply Voltage 6 6 Y1 Output Input Ground Function Table Y= /A Inputs Output A Y L H H L H = HIGH Logic Level L = LOW Logic Level © 1999 Fairchild Semiconductor Corporation NC7WZ14 • Rev. 1.0.7 www.fairchildsemi.com 2 Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. Max. Unit VCC Supply Voltage -0.5 7.0 V VIN DC Input Voltage -0.5 7.0 V VOUT 7.0 V IIK DC Input Diode Current VIN < -0.5V -50 mA IOK DC Output Diode Current VOUT < -0.5V -50 mA IOUT DC Output Current ±100 mA DC VCC or Ground Current ±50 mA +150 °C +150 °C +260 °C ICC or IGND TSTG DC Output Voltage -0.5 Storage Temperature Range -65 TJ Junction Temperature Under Bias TL Junction Lead Temperature (Soldering, 10 Seconds) SC70-6 PD ESD Power Dissipation TA=85°C 170 TA=125°C 104 MicroPak-6 130 MicroPak2-6 120 Human Body Model, JEDEC:JESD22-A114 4000 Charge Device Model, JEDEC:JESD22-C101 2000 mW V Recommended Operating Conditions(3) The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol VCC VIN VOUT TA JA Parameter Conditions Min. Max. Supply Voltage Operating 1.65 5.50 Supply Voltage Data Retention 1.5 5.5 0 5.5 V V Input Voltage Output Voltage Operating Temperature Thermal Resistance 0 VCC SC70-6 -40 +125 MicroPak-6 -40 +85 MicroPak2-6 -40 +85 SC70-6 390 MicroPak-6 500 MicroPak2-6 560 NC7WZ14 — TinyLogic® UHS Dual Inverter with Schmitt Trigger Inputs Absolute Maximum Ratings Unit V °C °C/W Note: 3. Unused inputs must be held HIGH or LOW. They may not float. © 1999 Fairchild Semiconductor Corporation NC7WZ14 • Rev. 1.0.7 www.fairchildsemi.com 3 Symbol Parameter VCC (V) TA=-40 to +85°C TA=+25°C Conditions Min. Typ. Max. VP VN VH Positive Threshold Voltage Negative Threshold Voltage Hysteresis Voltage 0.60 1.40 0.60 1.40 0.60 1.40 1.50 0.70 1.50 0.70 1.50 2.30 1.00 1.80 1.00 1.80 1.00 1.80 3.00 1.30 2.20 1.30 2.20 1.30 2.20 4.50 1.90 3.10 1.90 3.10 2.00 3.20 5.50 2.20 3.60 2.20 3.60 2.30 3.70 1.65 0.20 0.50 0.80 0.20 0.80 0.30 0.90 1.80 0.25 0.56 0.90 0.25 0.90 0.35 1.00 2.30 0.40 0.75 1.15 0.40 1.15 0.50 1.20 3.00 0.60 0.98 1.50 0.60 1.50 0.70 1.60 4.50 1.00 1.42 2.00 1.00 2.00 1.10 2.20 5.50 1.20 1.68 2.30 1.20 2.30 1.40 2.50 1.65 0.10 0.48 0.90 0.10 0.90 0.10 0.90 1.80 0.15 0.51 1.00 0.15 1.00 0.15 1.00 2.30 0.25 0.62 1.10 0.25 1.10 0.25 1.10 3.00 0.40 0.76 1.20 0.40 1.20 0.40 1.20 4.50 0.60 1.01 1.50 0.60 1.50 0.60 1.50 1.70 0.70 1.70 0.70 1.70 5.50 0.70 1.20 1.65 1.55 1.65 1.55 1.55 1.70 1.80 1.70 1.70 2.20 2.30 2.20 2.20 2.90 3.00 2.90 2.90 VIN=VIL, IOH=-100µA 4.50 4.40 4.50 4.40 4.40 1.65 IOH=-4mA 1.29 1.52 1.29 1.26 2.30 IOH=-8mA 1.90 2.14 1.90 1.80 3.00 IOH=-16mA 2.40 2.75 2.40 2.30 3.00 IOH=-24mA 2.30 2.62 2.30 2.20 4.50 IOH=-32mA 3.80 4.13 0.10 0.10 0.10 1.80 0.00 0.10 0.10 0.10 0.00 0.10 0.10 0.10 0.00 0.10 0.10 0.10 3.00 IIN Input Leakage Current IOFF Power Off Leakage Current ICC Quiescent Supply Current © 1999 Fairchild Semiconductor Corporation NC7WZ14 • Rev. 1.0.7 4.50 1.65 IOL=4mA V V 3.70 0.00 VIN=VIH, IOL=100µA V V 1.65 2.30 LOW Level Output Voltage 3.80 Units Max. 0.70 3.00 VOL Min. 1.65 2.30 HIGH Level Output Voltage Max. 1.80 1.80 VOH Min. TA=-40 to +125°C 0.00 0.10 0.10 0.10 0.08 0.24 0.24 0.26 V 2.30 IOL=8mA 0.10 0.30 0.30 0.32 3.00 IOL=16mA 0.16 0.40 0.40 0.43 3.00 IOL=24mA 0.24 0.55 0.55 0.60 4.50 IOL=32mA 0.25 0.55 0.55 0.60 ±0.1 ±1.0 ±2.0 µA 1 10 20 µA 1.0 10 20 µA 0 to 5.5 0 1.65 to 5.50 VIN=5.5V, GND VIN or VOUT=5.5V VIN=5.5V, GND NC7WZ14 — TinyLogic® UHS Dual Inverter with Schmitt Trigger Inputs DC Electrical Characteristics www.fairchildsemi.com 4 Symbol Parameter VCC (V) TA=+25°C Conditions TA=-40 to +85°C TA=-40 to +125°C Units Figure Min. Typ. Max. Min. Max. Min. Max. 1.65 2.5 7.6 13.1 2.5 14.5 2.5 14.7 1.80 2.5 6.3 10.9 2.5 12.0 2.5 12.3 1.8 4.3 7.4 1.8 8.1 1.8 8.4 3.30 ± 0.30 1.5 3.3 5.0 1.5 5.5 1.5 5.8 5.00 ± 0.50 1.0 2.7 4.1 1.0 4.5 1.0 4.8 3.30 ± 0.30 CL=50pF, 5.00 ± 0.50 RL=500 1.8 4.0 6.0 1.8 6.6 1.8 6.9 1.2 3.2 4.9 1.2 5.4 1.2 5.7 2.50 ± 0.20 tPLH, tPHL CIN CPD Propagation Delay CL=15pF, RL=1M Input Capacitance 0.00 2.5 Power Dissipation (4) Capacitance 3.30 11.0 5.00 12.5 Figure 5 Figure 6 ns Figure 5 Figure 6 pF pF Figure 7 Note: 4. CPD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (ICCD) at no output loading and operating at 50% duty cycle. CPD is related to ICCD dynamic operating current by the expression: ICCD=(CPD)(VCC)(fIN)+(ICCstatic). Note: 5. CL includes load and stray capacitance; Input PRR=1.0MHz; tW =500ns Figure 5. AC Test Circuit NC7WZ14 — TinyLogic® UHS Dual Inverter with Schmitt Trigger Inputs AC Electrical Characteristics Figure 6. AC Waveforms Note: 6. Input=AC Waveform; tr=tf=1.8ns; PRR=variable; Duty Cycle =50%. Figure 7. ICCD Test Circuit © 1999 Fairchild Semiconductor Corporation NC7WZ14 • Rev. 1.0.7 www.fairchildsemi.com 5 NC7WZ14 — TinyLogic® UHS Dual Inverter with Schmitt Trigger Inputs Physical Dimensions SYMM C L 2.00±0.20 0.65 A 0.50 MIN 6 4 B PIN ONE 1.25±0.10 1 1.90 3 0.30 0.15 (0.25) 0.40 MIN 0.10 0.65 A B 1.30 LAND PATTERN RECOMMENDATION 1.30 1.00 0.80 SEE DETAIL A 1.10 0.80 0.10 C 0.10 0.00 C 2.10±0.30 SEATING PLANE NOTES: UNLESS OTHERWISE SPECIFIED GAGE PLANE (R0.10) 0.25 0.10 0.20 A) THIS PACKAGE CONFORMS TO EIAJ SC-88, 1996. B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS DO NOT INCLUDE BURRS OR MOLD FLASH. D) DRAWING FILENAME: MKT-MAA06AREV6 30° 0° 0.46 0.26 DETAIL A SCALE: 60X Figure 8. 6-Lead, SC70, EIAJ SC-88a, 1.25mm Wide Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. Tape and Reel Specification Please visit Fairchild Semiconductor’s online packaging area for the most recent tape and reel specifications: http://www.fairchildsemi.com/products/analog/pdf/sc70-6_tr.pdf. Package Designator P6X © 1999 Fairchild Semiconductor Corporation NC7WZ14 • Rev. 1.0.7 Tape Section Cavity Number Cavity Status Cover Type Status Leader (Start End) 125 (Typical) Empty Sealed Carrier 3000 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed www.fairchildsemi.com 6 NC7WZ14 — TinyLogic® UHS Dual Inverter with Schmitt Trigger Inputs Physical Dimensions 2X 0.05 C 1.45 B 2X (1) 0.05 C (0.254) (0.49) 5X 1.00 (0.75) PIN 1 IDENTIFIER 5 (0.52) 1X A TOP VIEW 0.55MAX (0.30) 6X PIN 1 0.05 C 0.05 0.00 RECOMMENED LAND PATTERN 0.05 C C 0.25 0.15 6X 1.0 DETAIL A 0.10 0.05 0.45 0.35 0.10 0.00 6X C B A C 0.40 0.30 0.35 5X 0.25 0.40 5X 0.30 0.5 (0.05) 6X BOTTOM VIEW DETAIL A PIN 1 TERMINAL 0.075 X 45 CHAMFER (0.13) 4X Notes: 1. CONFORMS TO JEDEC STANDARD M0-252 VARIATION UAAD 2. DIMENSIONS ARE IN MILLIMETERS 3. DRAWING CONFORMS TO ASME Y14.5M-1994 4. FILENAME AND REVISION: MAC06AREV4 5. PIN ONE IDENTIFIER IS 2X LENGTH OF ANY OTHER LINE IN THE MARK CODE LAYOUT. Figure 9. 6-Lead, MicroPak™, 1.0mm Wide Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. Tape and Reel Specification Please visit Fairchild Semiconductor’s online packaging area for the most recent tape and reel specifications: http://www.fairchildsemi.com/products/logic/pdf/micropak_tr.pdf. Package Designator L6X © 1999 Fairchild Semiconductor Corporation NC7WZ14 • Rev. 1.0.7 Tape Section Cavity Number Cavity Status Cover Type Status Leader (Start End) 125 (Typical) Empty Sealed Carrier 5000 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed www.fairchildsemi.com 7 NC7WZ14 — TinyLogic® UHS Dual Inverter with Schmitt Trigger Inputs Physical Dimensions 0.89 0.35 0.05 C 1.00 2X B A 5X 0.40 PIN 1 MIN 250uM 0.66 1.00 1X 0.45 6X 0.19 0.05 C TOP VIEW RECOMMENDED LAND PATTERN FOR SPACE CONSTRAINED PCB 2X 0.90 0.05 C 0.35 0.55MAX C 5X 0.52 SIDE VIEW 0.73 (0.08) 4X 1 DETAIL A 2 1X 0.57 0.09 0.19 6X 3 0.20 6X ALTERNATIVE LAND PATTERN FOR UNIVERSAL APPLICATION (0.05) 6X 5X 0.35 0.25 6 5 4 0.35 0.60 (0.08) 4X 0.10 .05 C C B A 0.40 0.30 BOTTOM VIEW NOTES: A. COMPLIES TO JEDEC MO-252 STANDARD B. DIMENSIONS ARE IN MILLIMETERS. C. DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994 D. LANDPATTERN RECOMMENDATION IS BASED ON FSC DESIGN. E. DRAWING FILENAME AND REVISION: MGF06AREV3 0.075X45° CHAMFER DETAIL A PIN 1 LEAD SCALE: 2X Figure 10. 6-Lead, MicroPak2, 1x1mm Body, .35mm Pitch Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. Tape and Reel Specification Please visit Fairchild Semiconductor’s online packaging area for the most recent tape and reel specifications: http://www.fairchildsemi.com/packaging/MicroPAK2_6L_tr.pdf. Package Designator FHX © 1999 Fairchild Semiconductor Corporation NC7WZ14 • Rev. 1.0.7 Tape Section Cavity Number Cavity Status Cover Type Status Leader (Start End) 125 (Typical) Empty Sealed Carrier 5000 Filled Sealed Trailer (Hub End) 75 (Typical) Empty Sealed www.fairchildsemi.com 8 NC7WZ14 — TinyLogic® UHS Dual Inverter with Schmitt Trigger Inputs © 1999 Fairchild Semiconductor Corporation NC7WZ14 • Rev. 1.0.7 www.fairchildsemi.com 9