ES3A-ES3J Surface Mount Superfast Rectifiers Features ● Glass passivated chip junctions ● Ideal for automated placement ● Ultrafast reverse recovery time ● Low profile package ● High forward surge capability ● High temperature soldering： 260℃/10 seconds at terminals ● Component in accordance to RoHS 2002/95/1 and WEEE 2002/96/EC Major Ratings and Characteristics IF(AV) 3.0 A Case: JEDEC DO-214AA molded plastic VRRM 50 V to 600 V body over glass passivated chip IFSM 100 A Terminals: Solder plated, solderable per trr 35 nS J-STD-002B and JESD22-B102D VF 0.95 V, 1.25 V, 1.7 V Tj max. 150 °C Mechanical Date ● ● ● Polarity: Laser band denotes cathode end (TA = 25 °C unless otherwise noted) Maximum Ratings & Thermal Characteristics Items Symbol ES3A ES3B ES3C ES3D ES3E ES3G ES3H ES3J UNIT Maximum repetitive peak reverse voltage VRRM 50 100 150 200 300 400 500 600 V Maximum RMS voltage VRMS 35 70 105 140 210 280 350 420 V Maximum DC blocking voltage VDC 50 100 150 200 300 400 500 600 V Maximum average forward rectified current IF(AV) 3 A Peak forward surge current 8.3 ms single half sine-wave superimposed on rated load IFSM 100 A Thermal resistance from junction to lead(1) RθJL 25 ℃/ W TJ, TSTG –55 to +150 ℃ Operating junction and storage temperature range Note 1: Mounted on P.C.B. with 0.28 x 0.28” (7.0 x 7.0mm) copper pad areas. Electrical Characteristics Items Maximum Instantaneous forward voltage Maximum reverse current Reverse recovery time Typical junction capacitance (TA = 25 °C unless otherwise noted) Test conditions Symbol ES3A~D ES3E~G ES3H~J UNIT IF=3A(2) VF 0.95 1.25 1.70 V VR=VDC TA=25℃ TA=100℃ 5 50 μA IF=0.5A IR=1A Irr=0.25A trr 35 nS 4.0 V ,1MHz CJ 45 pF Note 2: Pulse test:300μs pulse width,1% duty cycle. http://www.trr-jx.com IR ES3A-ES3J Surface Mount Superfast Rectifiers Characteristic Curves http://www.trr-jx.com (TA=25 ℃ unless otherwise noted) ES3A-ES3J Surface Mount Superfast Rectifiers Package Outline Notice ● Product is intended for use in general electronics applications. ● Product should be worked less than the ratings; if exceeded, may cause permanent damage. or introduce latent failure ● The absolute maximum ratings are rated values and must not be exceeded during operation. The following are the general mechanisms. derating methods you design a circuit with a device. IF(AV) : We recommend that the worst case current be no greater than 80% . IFSM : This rating specifies the non-repetitive peak current. This is only applied for an abnormal operation, which the general during the lifespan of the device. TJ : Derate this rating when using a device in order to ensure high reliability. We recommend that the device be used at a TJ of below 125°C. ● TRR is registered trademark of Rising-sun Technology. Rising-sun Technology reserves the right to make changes to any product in this specification to improve reliability,functional characteristics,or design without notice. ● Rising-sun Technology does not assure any liability arising out of the applications or any product described in this specification. ● Rising-sun Technology advises customers to obtain the latest version of the device information before placing orders to verify that the required information is current. http://www.trr-jx.com