GP1FAV55TK0F GP1FAV55TK0F Fiber Optic Transmitter Square connector With mounting hole With shutter ■Description ■Agency approvals/Compliance GP1FAV55TK0F has a built-in LED with a peak light emission wavelength of 660 nm and the associated drive IC, and the input is TTL level compatible. This device is possible to high speed transmission of high quality audio signal (Transfer rate: MAX 50 Mb/s) 1. Compliant with JEITA RC-5720B and CP1201 2. Compliant with RoHS directive (2002/95/EC) ■Applications AV equipment (DVD, CD, MD players etc.) ■Features 1. Fiber optic transmitter 2. Square connector (JEITA RC-5720B) 3. With mounting hole 4. With shutter function 5. Supply voltage : 5 V 6. Transfer rate : 50 Mb/s Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Sheet No.: E2-A00701EN Date Dec.01.2006 ©SHARP Corporation 1 GP1FAV55TK0F ■Outline Dimensions Symbol A B C D Description Holder Shutter Fixing pin Lead pin (Unit: mm) Material PBT (Color : Black) PBT (Color : Black) PBT (Color : Black) Cu Alloy (SnCu plating) [1] φ2 .3 ± 0. 1 co un ter bo re φ4 [2] (Lead root) (Lead root) Example of mounting drawing from solder side. Unspecified tolerance ± 0.1 Internal Equivalent Circuit Pin Arrangement Vin *1 LED DRIVER IC Vcc GND *1 Input conditions of Vin terminal are designed to conform to TTL and CMOS. It is recommended that the output of TTL and high speed CMOS be used in the input for Vin terminal. [2]Portion marking 1) The connector joint area complies with the square connector JEITA RC-5720B. 2) [1] portion : “S” mark, [2] portion : Model No. and date code shall be indicated. 3) Unspecified tolerance are ± 0.3 4) Since there are other products which has a different fixing pin shape, please make sure to confirm reference mounting drawing for this device. Production year (Last digit of production year) Production month 5 5 Jan to Sep: 1 - 9 10 Oct: X 11 Nov: Y 12 Dec: Z T Model Number Product mass : approx. 3 g Sheet No.: E2-A00701EN 2 GP1FAV55TK0F ■Absolute Maximum Ratings Parameter Supply voltage Input voltage Operating temperature Storage temperature Soldering temperature *1 Symbol Rating VCC -0.5 to +7.0 Vin -05. to VCC+0.5 Topr -20 to +70 Tstg -30 to +80 260 Tsol 380 Unit Remark V V °C °C °C 5 s or less/time up to 2 times. 4 s or less/time up to 1 time. °C Soldering by hand at each terminal. *2 *1 Solder at a position more than 1.6 mm away from the base of the lead terminal. Reflow is not available. *2 Do not contact top of soldering iron to lead terminal directly. ■Recommended Operating Conditions Parameter Supply voltage Operating transfer rate Symbol VCC T MIN. 4.75 - TYP. 5.0 - MAX. 5.25 50.0 Unit Remark V Mb/s NRZ signal duty 50% ■Electro-optical Characteristics (Ta = 25 °C, VCC = 5V) Parameter Symbol Conditions MIN. λp Peak emission wavelength 630 PC Output optical power couple into fiber Measurement method refer to Fig. 1 -21 ICC Supply current ViH Measurement method refer to Fig. 2 High level input voltage 2.0 ViL Low level input voltage tpLH L → H delay time → t H L delay time pHL Measurement method refer to Fig. 3, 4 Δtw Pulse width distortion -9 Δtj Jitter - TYP. 660 -18 8 1 MAX. Unit 690 nm -15 dBm 13 mA V 0.8 V 180 ns 180 ns +9 ns 8 ns Sheet No.: E2-A00701EN 3 GP1FAV55TK0F ■Measurement Method Fig. 1 Output Optical Power Coupled Into Fiber Standard fiber optic cable GP1FAV55TK0F Device under test Vcc Vin Optical power meter (Anritsu) ML93B GND The optical power meter must be calibrated to 660 nm. (0 dBm = 1 mW) Vcc D Notes 1. Vcc = 5.0 V (State of operating) 2. To bundle up the standard fiber optic cable, make it into a loop with the diameter D = 10 cm or more. (The standard fiber optic cable will be specified elsewhere.) Fig. 2 Input Voltage and Supply Current Standard fiber optic cable GP1FAV55TK0F Device under test Vin Vcc Optical power meter (Anritsu) ML93B GND The optical power meter must be calibrated to 660 nm. (0 dBm = 1 mW) Icc Vin Vcc Input conditions and judgment method No. Input conditions V 1 in = 2.0 V or more Vin = 0.8 V or less 2 Judgment method -21 ≤ PC ≤ -15 dBm, ICC = 13 mA or less PC ≤ -36 dBm, ICC = 13 mA or less Notes Vcc = 5.0 V (State of operating) Sheet No.: E2-A00701EN 4 GP1FAV55TK0F Fig. 3 Pulse Response and Jitter Standard fiber optic cable GP1FAV55TK0F Device under test Vin Vcc Standard receiver Output signal GND Icc Vin Vcc Oscilloscope (band width: 1 GHz) Trigger: CH1 Mode: Storage mode CH1 CH2 Input Oscilloscope 1 1 0 0 Input signal 12.5 Mb/s bi-phase PRBS signal Fig. 4 Input Signal (12.5 Mb/s Bi-phase PRBS Signal) Input signal 50% tpHL tpLH Standard receiver output 50% ∆tjr ∆tjf Notes (1) The wave form write time shall be 4 s. But do not allow the wave form to be distorted by increasing the brightness too much. (2) VCC = 5.0 V (State of operating) (3) The probe for the oscilloscope must be more than 1 MΩ and less than 10 pF. Sheet No.: E2-A00701EN 5 GP1FAV55TK0F ■Design and Production Notes (1) Stabilization of power supply line Please put a by-pass capacitor (0.1 μF) close to the device at least within 7 mm of the terminal. Please also put a 4.7 μF capacitor across the power supply line nearby. (2) Soldering condition Solder at the condition within the absolute maximum ratings in this sheet. In case of using flow soldering, please make sure of the conditions of process at the flow equipment. Also, do not use reflow soldering. In case of soldering by hand, do not contact top of soldering iron to lead terminal directly. (Solder at a position more than 1.6 mm away from the base of the lead terminal.) (3) About getting dirt and dust in the connector coupling portion In case dirt or dust comes into the connector coupling portion, please use a blower to take it off. Any rigid rod-like object must not be inserted since into the coupling portion. The internal device might be damaged, resulting deteriorated characteristics. (4) Cleaning Do not immerse for cleaning. The solvent would get into the connector coupling portion resulting deteriorated characteristics. Should it be necessary to remove the flux, please use one of the following solvents only to be applied with a brush. Solvent : Isopropyl alcohol, Methyl alcohol (5) Ground during assembling The human body and the soldering iron must be grounded against the static breakdown of the device during assembling. Please avoid touching the device terminals as much as possible before assembling. (6) Assembly of the device Please fix this device with a screw. In case that this device is not fixed with a screw, stress by detaching connector of internal elements and leads can adversely affect the device’s reliability. Excessive torque can deform the package and damage the optics. It can also adversely affect the device’s reliability because the device is used under continuous stress. Please confirm the limit of fixing torque to the installation before fixing actually. Recommended values Screw : M3.0 × 8 mm tapping screw Fixing torque : 0.7 to 0.8 N·m Force applied by driver etc. : 39 N or less Note : Please contact and consult with a Sharp sales representative for any questions about above. (7) Input signal This product is designed intentionally based upon the signal transmission which is defined by the digital audio interface standard ; CP1201. When a signal out of JEITA standard CP-1201 is inputted to this device, there might be a case that this device can not transmit a signal correctly to receiving unit. (8) Fixing pin Since there are other products which has a different fixing pin shape, please make sure to confirm reference mounting drawing for this device. (9) Damage to connector coupling portion Please do not stress the connector coupling portion excessively since there might be a case that the shutter can’t operate normally. (10) About getting the flux into connector coupling portion Please avoid getting a flux into connector coupling portion of this device, because there might be a case that the characteristics deteriorate the shutter can’t operate normally. Sheet No.: E2-A00701EN 6 GP1FAV55TK0F ●Presence of ODC etc. This product shall not contain the following materials. And they are not used in the production process for this product. Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform) Specific brominated flame retardants such as the PBB and PBDE are not used in this product at all. This product shall not contain the following materials banned in the RoHS Directive (2002/95/EC). • Lead, Mercury, Cadmium, Hexavalent chromium, Polybrominated biphenyls (PBB), Polybrominated diphenyl ethers (PBDE). ■Packing Specifications PRODUCT TRAY PRODUCT Cross section of tray PACKING MATERIAL Tray : Polystyrene PACKING METHOD Each tray holds 200 pieces. Sheet No.: E2-A00701EN 7 GP1FAV55TK0F ■Important Notices · The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii) SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). · Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. · Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection · If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is necessary to obtain approval to export such SHARP devices. · This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. · Contact and consult with a SHARP representative if there are any questions about the contents of this publication. Sheet No.: E2-A00701EN 8